Growth and Optical Properties of Direct Band Gap Ge/Ge0.87Sn0.13 Core/Shell Nanowire Arrays.

Group IV semiconductor optoelectronic devices are now possible by using strain-free direct band gap GeSn alloys grown on a Ge/Si virtual substrate with Sn contents above 9%. Here, we demonstrate the growth of Ge/GeSn core/shell nanowire arrays with Sn incorporation up to 13% and without the formation of Sn clusters. The nanowire geometry promotes strain relaxation in the Ge0.87Sn0.13 shell and limits the formation of structural defects. This results in room-temperature photoluminescence centered at 0.465 eV and enhanced absorption above 98%. Therefore, direct band gap GeSn grown in a nanowire geometry holds promise as a low-cost and high-efficiency material for photodetectors operating in the short-wave infrared and thermal imaging devices.

Boosting Hole Mobility in Coherently Strained [110]-Oriented Ge-Si Core-Shell Nanowires.

The ability of core-shell nanowires to overcome existing limitations of heterostructures is one of the key ingredients for the design of next generation devices. This requires a detailed understanding of the mechanism for strain relaxation in these systems in order to eliminate strain-induced defect formation and thus to boost important electronic properties such as carrier mobility. Here we demonstrate how the hole mobility of [110]-oriented Ge-Si core-shell nanowires can be substantially enhanced thanks to the realization of large band offset and coherent strain in the system, reaching values as high as 4200 cm2/(Vs) at 4 K and 1600 cm2/(Vs) at room temperature for high hole densities of 1019 cm-3. We present a direct correlation of (i) mobility, (ii) crystal direction, (iii) diameter, and (iv) coherent strain, all of which are extracted in our work for individual nanowires. Our results imply [110]-oriented Ge-Si core-shell nanowires as a promising candidate for future electronic and quantum transport devices.

Atom-by-Atom Analysis of Semiconductor Nanowires with Parts Per Million Sensitivity.

The functionality of semiconductor devices is determined by the incorporation of dopants at concentrations down to the parts per million (ppm) level and below. Optimization of intentional and unintentional impurity doping relies on methods to detect and map the level of impurities. Detecting such low concentrations of impurities in nanostructures is however challenging to date as on the one hand methods used for macroscopic samples cannot be applied due to the inherent small volumes or faceted surfaces and on the other hand conventional microscopic analysis techniques are not sufficiently sensitive. Here, we show that we can detect and map impurities at the ppm level in semiconductor nanowires using atom probe tomography. We develop a method applicable to a wide variety of nanowires relevant for electronic and optical devices. We expect that it will contribute significantly to the further optimization of the synthesis of nanowires, nanostructures and devices based on these structures.

An atomic scale study of surface termination and digital alloy growth in InGaAs/AlAsSb multi-quantum wells.

An atomic scale study has been performed to understand the influence of the (As,Sb) shutter sequences during interface formation on the optical properties of InGaAs/AlAsSb quantum wells. Our cross-sectional scanning tunneling microscopy results show that the onset of the Sb profile is steep in the Sb-containing layers whereas an appreciable segregation of Sb in the subsequently grown Sb free layers is observed. The steep rise of the Sb profile is due to extra Sb that is supplied to the surface prior to the growth of the Sb-containing layers. No relation is found between the (As,Sb) termination conditions of the Sb-containing layers and the resulting Sb profiles in the capping layers. Correspondingly we see that the optical properties of these quantum wells are also nearly independent on the (As,Sb) shutter sequences at the interface. Digital alloy growth in comparison to conventional molecular beam epitaxy growth was also explored. X-ray results suggest that the structural properties of the quantum well structures grown by conventional molecular beam epitaxy techniques are slightly better than those formed by digital alloy growth. However photoluminescence studies indicate that the digital alloy samples give rise to a more intense and broader photoluminescence emission. Cross-sectional scanning tunneling microscopy measurements reveal that lateral composition modulations present in the digital alloys are responsible for the enhancement of the photoluminescence intensity and inhomogeneous broadening.

Bistable Si dopants in the GaAs (1 1 0) surface.

In this review, recent work is discussed on bistable Si dopants in the GaAs (1 1 0) surface, studied by scanning tunneling microscopy (STM). The bistability arises because the dopant atom can switch between a positive and a negative charge state, which are associated with two different lattice configurations. Manipulation of the Si atom charge configuration is achieved by tuning the local band bending with the STM tip. Furthermore, illuminating the sample with a laser also influences the charge state, allowing the operation of the dopant atom as an optical switch. The switching dynamics without illumination is investigated in detail as a function of temperature, lateral tip position, and applied tunneling conditions. A physical model is presented that independently describes the thermal and quantum tunneling contributions to the switching frequency and charge state occupation of a single Si atom. The basic functionality of a memory cell is demonstrated employing a single bistable Si dopant as the active element, using the STM tip as a gate to write and read the information.

Spin-orbit-induced circulating currents in a semiconductor nanostructure.

Circulating orbital currents produced by the spin-orbit interaction for a single electron spin in a quantum dot are explicitly evaluated at zero magnetic field, along with their effect on the total magnetic moment (spin and orbital) of the electron spin. The currents are dominated by coherent superpositions of the conduction and valence envelope functions of the electronic state, are smoothly varying within the quantum dot, and are peaked roughly halfway between the dot center and edge. Thus the spatial structure of the spin contribution to the magnetic moment (which is peaked at the dot center) differs greatly from the spatial structure of the orbital contribution. Even when the spin and orbital magnetic moments cancel (for g=0) the spin can interact strongly with local magnetic fields, e.g., from other spins, which has implications for spin lifetimes and spin manipulation.

Bistable charge configuration of donor systems near the GaAs(110) surfaces.

In gated semiconductor devices, the space charge layer that is located under the gate electrode acts as the functional element. With increasing gate voltage, the microscopic process forming this space charge layer involves the subsequent ionization or electron capture of individual dopants within the semiconductor. In this Letter, a scanning tunneling microscope tip is used as a movable gate above the (110) surface of n-doped GaAs. We study the build-up process of the space charge region considering donors and visualize the charge states of individual and multi donor systems. The charge configuration of single donors is determined by the position of the tip and the applied gate voltage. In contrast, a two donor system with interdonor distances smaller than 10 nm shows a more complex behavior. The electrostatic interaction between the donors in combination with the modification of their electronic properties close to the surface results in ionization gaps and bistable charge switching behavior.

Shape and size control of InAs/InP (113)B quantum dots by Sb deposition during the capping procedure.

The role of Sb atoms present on the growth front during capping of InAs/InP (113)B quantum dots (QDs) is investigated by cross-sectional scanning tunnelling microscopy, atomic force microscopy, and photoluminescence spectroscopy. Direct capping of InAs QDs by InP results in partial disassembly of InAs QDs due to the As/P exchange occurring at the surface. However, when Sb atoms are supplied to the growth surface before InP capping layer overgrowth, the QDs preserve their uncapped shape, indicating that QD decomposition is suppressed. When GaAs(0.51)Sb(0.49) layers are deposited on the QDs, conformal growth is observed, despite the strain inhomogeneity existing at the growth front. This indicates that kinetics rather than the strain plays the major role during QD capping with Sb compounds. Thus Sb opens up a new way to control the shape of InAs QDs.

Nanoscale potential fluctuations in (GaMn)As/GaAs heterostructures: from individual ions to charge clusters and electrostatic quantum dots.

During growth of the dilute p-type ferromagnetic semiconductor Ga1-xMnxAs, interstitial manganese, Mni(2+), is formed when x exceeds 2%. The double donor Mni(2+) compensates the free holes that mediate ferromagnetism. Annealing causes out-diffusion of these interstitials, thereby increasing the Curie temperature. Here, we use cross sectional scanning tunneling microscopy and spectroscopy to visualize the potential landscape which arises due to the clustering of Mni(2+) in annealed p-i-n (GaMn)As-GaAs double barrier heterostructures. We map the local minima in the potential landscape, link them to clusters of individual Mni(2+) ions, and show that the ions are doubly charged.

An atomically resolved study of InGaAs quantum dot layers grown with an indium flush step.

In this cross-sectional scanning tunnelling microscopy study we investigate the indium flush method as a means to control the height of self-assembled InGaAs quantum dots and wetting layers. The results show that application of an indium flush step during growth results in flattened dots and a reduced wetting layer of which the height can be precisely controlled by varying the height of the first capping layer.

Surface induced asymmetry of acceptor wave functions.

Measurements of the local density of states of individual acceptors in III-V semiconductors show that the symmetry of the acceptor states strongly depends on the depth of the atom below a (110) surface. Tight-binding calculations performed for a uniformly strained bulk material demonstrate that strain induced by the surface relaxation is responsible for the observed depth-dependent symmetry breaking of acceptor wave functions. As this effect is strongest for weakly bound acceptors, it explains within a unified approach the commonly observed triangular shapes of shallow acceptors and the crosslike shapes of deeply bound acceptor states in III-V materials.

Enhanced donor binding energy close to a semiconductor surface.

We measured the ionization threshold voltage of individual impurities close to a semiconductor-vacuum interface, where we use the STM tip to ionize individual donors. We observe a reversed order of ionization with depth below the surface, which proves that the binding energy is enhanced towards the surface. This is in contrast to the predicted reduction for a Coulombic impurity in the effective mass approach. We can estimate the binding energy from the ionization threshold and show experimentally that in the case of silicon doped gallium arsenide the binding energy gradually increases over the last 1.2 nm below the (110) surface.

Simple and efficient scanning tunneling luminescence detection at low-temperature.

We have designed and built an optical system to collect light that is generated in the tunneling region of a low-temperature scanning tunneling microscope. The optical system consists of an in situ lens placed approximately 1.5 cm from the tunneling region and an ex situ optical lens system to analyze the emitted light, for instance, by directing the light into a spectrometer. As a demonstration, we measured tip induced photoluminescence spectra of a gold surface. Furthermore, we demonstrate that we can simultaneously record scanning tunneling microscope induced luminescence and topography of the surface both with atomic resolution.

Controlled charge switching on a single donor with a scanning tunneling microscope.

The charge state of individually addressable impurities in semiconductor material was manipulated with a scanning tunneling microscope. The manipulation was fully controlled by the position of the tip and the voltage applied between tip and sample. The experiments were performed at low temperature on the (110) surface of silicon doped GaAs. Silicon donors up to 1 nm below the surface can be reversibly switched between their neutral and ionized state by the local potential induced by the tip. By using ultrasharp tips, the switching process occurs close enough to the impurity to be observed as a sharp circular feature surrounding the donor. By utilizing the controlled manipulation, we were able to map the Coulomb potential of a single donor at the semiconductor-vacuum interface.

Self-assembling processes involved in the molecular beam epitaxy growth of stacked InAs/InP quantum wires.

The growth mechanism of stacked InAs/InP(001) quantum wires (QWRs) is studied by combining an atomic-scale cross-sectional scanning tunnelling microscopy analysis with in situ and in real-time stress measurements along the [110] direction (sensitive to stress relaxation during QWR formation). QWRs in stacked layers grow by a non-Stranski-Krastanov (SK) process which involves the production of extra InAs by strain-enhanced As/P exchange and a strong strain driven mass transport. Despite the different growth mechanism of the QWR between the first and following layers of the stack, the QWRs maintain on average the same shape and composition in all the layers of the stack, revealing the high stability of this QWR configuration.

Oscillatory persistent currents in self-assembled quantum rings.

We report the direct measurement of the persistent current carried by a single electron by means of magnetization experiments on self-assembled InAs/GaAs quantum rings. We measured the first Aharonov-Bohm oscillation at a field of 14 T, in perfect agreement with our model based on the structural properties determined by cross-sectional scanning tunneling microscopy measurements. The observed oscillation magnitude of the magnetic moment per electron is remarkably large for the topology of our nanostructures, which are singly connected and exhibit a pronounced shape asymmetry.

Warping a single Mn acceptor wavefunction by straining the GaAs host.

Transition-metal dopants such as Mn determine the ferromagnetism in dilute magnetic semiconductors such as Ga(1-x)Mn(x)As. Recently, the acceptor states of Mn dopants in GaAs were found to be highly anisotropic owing to the symmetry of the host crystal. Here, we show how the shape of such a state can be modified by local strain. The Mn acceptors near InAs quantum dots are mapped at room temperature by scanning tunnelling microscopy. Dramatic distortions and a reduction in the symmetry of the wavefunction of the hole bound to the Mn acceptor are observed originating from strain induced by quantum dots. Calculations of the acceptor-state wavefunction in the presence of strain, within a tight-binding model and within an effective-mass model, agree with the experimentally observed shape. The magnetic easy axes of strained lightly doped Ga(1-x)Mn(x)As can be explained on the basis of the observed local density of states for the single Mn spin.

Spatial structure of Mn-Mn acceptor pairs in GaAs.

The local density of states of Mn-Mn pairs in GaAs is mapped with cross-sectional scanning tunneling microscopy and compared with theoretical calculations based on envelope-function and tight-binding models. These measurements and calculations show that the crosslike shape of the Mn-acceptor wave function in GaAs persists even at very short Mn-Mn spatial separations. The resilience of the Mn-acceptor wave function to high doping levels suggests that ferromagnetism in GaMnAs is strongly influenced by impurity-band formation. The envelope-function and tight-binding models predict similarly anisotropic overlaps of the Mn wave functions for Mn-Mn pairs. This anisotropy implies differing Curie temperatures for Mn delta-doped layers grown on differently oriented substrates.

Spatial structure of an individual Mn acceptor in GaAs.

The wave function of a hole bound to an individual Mn acceptor in GaAs is spatially mapped by scanning tunneling microscopy at room temperature and an anisotropic, crosslike shape is observed. The spatial structure is compared with that from an envelope-function, effective mass model and from a tight-binding model. This demonstrates that anisotropy arising from the cubic symmetry of the GaAs crystal produces the crosslike shape for the hole wave function. Thus the coupling between Mn dopants in GaMnAs mediated by such holes will be highly anisotropic.

Apparent antifungal activity of several lactic acid bacteria against Penicillium discolor is due to acetic acid in the medium.

Fifty-six dairy bacteria belonging to the genera Lactococcus, Lactobacillus, Pediococcus, Propionibacterium, Streptococcus, Enterococcus, Leuconostoc, and Brevibacterium were screened for antifungal activity against four species of fungi relevant to the cheese industry (Penicillium discolor, Penicillium commune, Penicillium roqueforti, and Aspergillus vesicolor). Most of the active strains belonged to the genus Lactobacillus, whereas Penicillium discolor was found to be the most sensitive of the four fungi investigated. Further studies on P. discolor showed antifungal activity only below pH 5. This effect of pH suggests that organic acids present in the culture could be involved in the detected activity. Determination of acid composition revealed lactic acid production for active dairy strains and the presence of acetic acid in active as well as inactive strains. It was demonstrated that the undissociated acetic acid originates from the bacterial growth medium. The synergistic effect of the acetic acid present and the lactic acid produced was likely the main factor responsible for the antifungal properties of the selected bacteria. These results could explain some discrepancies in reports of the antifungal properties of lactic acid bacteria, since the role of acetic acid has not been considered in previous studies.