Evaluation of slurry sampling preparation of enteral nutrition formulations for multielement determination using inductively coupled plasma optical emission spectrometry.

An analytical procedure for the multielement determination in enteral nutrition formulations employing slurry sampling and inductively coupled plasma optical emission spectrometry (ICP OES) is proposed. A two-level full-factorial design was applied to assess the influence of the presence of stabilizing agents (HNO3, Triton X-100 and ethanol) on the composition of the slurry. Multiple response was established as a dependent variable. The experimental conditions for the preparation of the slurry were: 2.0 mL of sample and 8.0 mL of 10% (v/v) HNO3. The limits of detection (LOD) were 5; 9; and 10 µg L-1 for Cu, Fe, Zn, respectively. For P, and K, the LOD were 8 and 24 mg L-1, respectively. The method was applied for the analysis of three enteral nutrition formulation samples and the obtained concentrations ranges were (in mg L-1): 0.41-0.43 (Cu), 2.0-2.9 (Fe), 1.7-3.1 (Zn), 682-1409 (K), and 217-344 (P).

Multivariate optimization of ultrasound-assisted extraction using Doehlert matrix for simultaneous determination of Fe and Ni in vegetable oils by high-resolution continuum source graphite furnace atomic absorption spectrometry.

A method for simultaneous determination of Fe (232.036 nm) and Ni (232.195 nm) in vegetable oil samples by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) after an acid extraction of the analytes is proposed. In the extraction step, hydrochloric, nitric and acetic acid solutions were tested. The optimization of the procedure was performed by applying Doehlert matrix, and multiple response was used for simultaneous evaluation of the performance of the extraction. The optimum conditions were: extraction time of 17 min, extraction temperature of 39 °C and sonication amplitude of 42%, employing 0.5 mol L-1 HCl as the extracting solvent. The limits of quantification were 60 and 160 ng g-1 for Fe and Ni, respectively. The method was applied to the analysis of vegetable oil samples and the results were compared with a method employing inductively coupled plasma optical emission spectrometry (ICP OES).

Focused microwave-induced combustion: a new technique for sample digestion.

A procedure for sample digestion based on focused microwave-induced combustion (FMIC) is proposed. This system was developed using a commercial focused microwave oven with a lab-made quartz sample holder and a modified glass vessel. Oxygen flow was used to start and support the combustion. A botanical sample was used to evaluate the operational conditions for further Al, Ba, Ca, Fe, Mg, Mn, Sr, and Zn determination by inductively coupled plasma optical emission spectrometry. Pelletized samples were positioned on the quartz holder, and 50 microL of 6 mol L(-1) NH(4)NO(3) solution was added as igniter. Combustion was completed in less than 2 min, and the temperature was higher than 950 degrees C. The use of a reflux step, the position of sample holder inside the vessel, sample mass, ignition and combustion time, oxygen flow rate, and condenser type were evaluated. Results were compared with those obtained by focused microwave-assisted wet digestion and by high pressure microwave-assisted wet digestion. Agreement of 95-103% was obtained for certified reference materials digested by FMIC (reflux step with 10 mL of 4 mol L(-1) HNO(3)). With the proposed procedure, a complete sample decomposition (residual carbon content lower than 0.5%) was achieved with low consumption of reagents as only 10 mL of diluted nitric acid was necessary. Low relative standard deviation (lower than 3.8%) was observed and high amount of sample (up to 1500 mg) could be digested that allowed lower limits of detection.

A preconcentration system for determination of copper and nickel in water and food samples employing flame atomic absorption spectrometry.

A separation/preconcentration procedure using solid phase extraction has been proposed for the flame atomic absorption spectrometric determination of copper and nickel at trace level in food samples. The solid phase is Dowex Optipore SD-2 resin contained on a minicolumn, where analyte ions are sorbed as 5-methyl-4-(2-thiazolylazo) resorcinol chelates. After elution using 1 mol L(-1) nitric acid solution, the analytes are determinate employing flame atomic absorption spectrometry. The optimization step was performed using a full two-level factorial design and the variables studied were: pH, reagent concentration (RC) and amount of resin on the column (AR). Under the experimental conditions established in the optimization step, the procedure allows the determination of copper and nickel with limit of detection of 1.03 and 1.90 microg L(-1), respectively and precision of 7 and 8%, for concentrations of copper and nickel of 200 microg L(-1). The effect of matrix ions was also evaluated. The accuracy was confirmed by analyzing of the followings certified reference materials: NIST SRM 1515 Apple leaves and GBW 07603 Aquatic and Terrestrial Biological Products. The developed method was successfully applied for the determination of copper and nickel in real samples including human hair, chicken meat, black tea and canned fish.