Knee Loading After ACL-R Is Related to Quadriceps Strength and Knee Extension Differences Across the Continuum of Care.

BACKGROUND: Quadriceps strength and knee extension are believed to be important in the ability to effectively load the knee after anterior cruciate ligament (ACL) reconstruction (ACL-R). PURPOSE: To compare quadriceps strength (QUADS), side-to-side knee extension difference (ExtDiff), and knee energy absorption contribution (EAC) in patients preoperatively, 12 weeks postoperatively, and at return to sport (RTS). A secondary aim was to determine how the factors of QUADS and ExtDiff contributed to the ability to load the knee (knee EAC) at each of the 3 time points. STUDY DESIGN: Case series; Level of evidence, 4. METHODS: Overall, 41 individuals (mean ± SD age, 15.95 ± 1.63 years) were enrolled in this study. QUADS, ExtDiff, and knee EAC during a double-limb squat were collected preoperatively, 12 weeks postoperatively, and at RTS. Isokinetic QUADS was collected at 60 deg/s, normalized to body mass, and averaged across 5 trials. Knee extension was measured with a goniometer, and ExtDiff was calculated for analyses. Knee EAC was measured during double-limb squat descent and was calculated as a percentage of total energy absorption for the limb. Observations were obtained from both the surgical and nonsurgical limbs at the 3 time points. A mixed regression model with random intercept to compare change over the 3 time points was used, and a model selection was conducted with Akaike information criteria. Significance was set at P < .05. RESULTS: Surgical limb QUADS was significantly lower preoperatively (mean ± SD, 1.37 ± 0.49 N·m/kg; P = .0023) and at 12 weeks (1.11 ± 0.38 N·m/kg; P < .0001) than at RTS (1.58 ± 0.47 N·m/kg). Nonsurgical limb QUADS was also significantly lower preoperatively (2.01 ± 0.54 N·m/kg; P < .0256) and at 12 weeks (2.03 ± 0.48 N·m/kg; P < .0233) than at RTS (2.18 ± 0.54 N·m/kg). Knee EAC for the surgical limb was significantly lower at 12 weeks than at RTS (40.98% ± 13.73% vs 47.50% ± 12.04%; P < .0032), and ExtDiff was significantly greater preoperatively than at RTS (-2.68° ± 3.19° vs -0.63° ± 1.43°; P < .0001). Preoperatively, QUADS for both the surgical (P < .0003) and nonsurgical (P = .0023) limbs was a significant predictor of surgical limb knee EAC, explaining 33.99% of the variance. At 12 weeks, surgical limb QUADS was a significant predictor (P < .0051) of surgical limb knee EAC, explaining 18.83% of the variance. At RTS, ExtDiff was a significant predictor (P = .0201) of surgical limb knee EAC, explaining 12.92% of the variance. CONCLUSION: The ability to load the knee after ACL injury changes across the continuum of care and is related to QUADS and ExtDiff. These results provide clinicians with insight into potential contributing factors that may limit knee loading during the rehabilitation process.

Stability of Locking Plate and Compression Screws for Lapidus Arthrodesis: A Biomechanical Comparison of Plate Position.

Lapidus (first tarsometatarsal joint) arthrodesis is an established and widely used procedure for the management of moderate to severe hallux valgus, especially in cases involving hypermobility of the first tarsometatarsal joint. Multiple fixation methods are available, and several previous investigations have studied the relative strengths of these methods, including dorsomedial and plantar plating comparisons. However, these studies compared plates of varying designs and mechanical properties and used varying modes of compression and interfragmentary screw techniques. The present study mechanically investigated the resulting motion, stiffness, and strength of identical locking plate constructs fixed at various anatomic positions around the first tarsometatarsal joint. In a bench-top study, fourth-generation composite bones were divided into 3 fixation groups, each having identical interfragmentary screw applications, and randomized to 1 of 3 plate positions: dorsal, medial, or plantar. The plates applied in each case were identical locking plates, precontoured to fit the anatomy. Each construct was experimentally tested using a cantilever bending approach. The outcomes obtained were stiffness, yield force, displacement at yield, ultimate force, and displacement at ultimate force. The plantar plate position showed superior initial stiffness and force to ultimate failure. The plantar and medial plate positions exhibited superior force to yield. The medial plate position was superior regarding displacement tolerated before the yield point and catastrophic failure. The dorsal plate position was not superior for any outcome measured. Plantar and medial plating each offered biomechanical benefits. Clinical studies using similarly matched constructs are required to show whether these findings translate into improved clinical outcomes.

Biomechanical behavior of novel composite PMMA-CaP bone cements in an anatomically accurate cadaveric vertebroplasty model.

Vertebral compression fractures are caused by many factors including trauma and osteoporosis. Osteoporosis induced fractures are a result of loss in bone mass and quality that weaken the vertebral body. Vertebroplasty and kyphoplasty, involving cement augmentation of fractured vertebrae, show promise in restoring vertebral mechanical properties. Some complications however, are reported due to the performance characteristics of commercially available bone cements. In this study, the biomechanical performance characteristics of two novel composite (PMMA-CaP) bone cements were studied using an anatomically accurate human cadaveric vertebroplasty model. The study involves mechanical testing on two functional cadaveric spinal unit (2FSU) segments which include monotonic compression and cyclical fatigue tests, treatment by direct cement injection, and microscopic visualization of sectioned vertebrae. The 2FSU segments were fractured, treated, and mechanically tested to investigate the stability provided by two novel bone cements; using readily available commercial acrylic cement as a control. Segment height and stiffness were tracked during the study to establish biomechanical performance. The 2FSU segments were successfully stabilized with all three cement groups. Stiffness values were restored to initial levels following fatigue loading. Cement interdigitation was observed with all cement groups. This study demonstrates efficient reinforcement of the fractured vertebrae through stiffness restoration. The pre-mixed composite cements were comparable to the commercial cement in their performance and interdigitative ability, thus holding promise for future clinical use. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2067-2074, 2017.

In Vitro and In Vivo Characterization of Premixed PMMA-CaP Composite Bone Cements.

Acrylic bone cements, although successful in the field of orthopedics, suffer from a lack of bioactivity, not truly integrating with surrounding bone. Bioactive fixation is expected to enhance cement performance because of the natural interlocking and bonding with bone, which can improve the augmentative potential of the material in applications such as vertebroplasty (VP). In a recent study, two composite cements (PMMA-hydroxyapatite and PMMA-brushite) showed promising results demonstrating no deterioration in rheological and mechanical properties after CaP filler addition. In this study, the dynamic properties of the cements were investigated in vitro and in vivo. The hypothesis was that these composite cements will provide osseointegration around the implanted cement and increase new bone formation, thus decreasing the risk of bone structural failure. The effects of CaP elution were thus analyzed in vitro using these cements. Mass-loss, pore formation, and mechanical changes were tracked after cement immersion in Hank's salt solution. PMMA-brushite was the only cement with a significant mass loss; however it showed low bulk porosity. Surface porosity increases were observed in both composite cements. Mechanical properties were maintained after cement immersion. In vitro culture studies tested preosteoblast cell viability and differentiation on the cement surface. Cell viability was demonstrated with MTT assay and confirmed on the cement surface. ALP assays showed no inhibition of osteoblast differentiation on the cement surface. In vivo experiments were performed using a rat tibiae model to demonstrate bone ingrowth around the implanted cements. Critical size defects were created and then filled with the cements. The animal studies showed no loss in mechanical strength after implantation and increased bone ingrowth around the composite cements. In summary, the composite cements provided bioactivity without sacrificing mechanical strength.

Stem geometry changes initial femoral fixation stability of a revised press-fit hip prosthesis: A finite element study.

BACKGROUND: Stable femoral fixation during uncemented total hip arthroplasty is critical to allow for subsequent osseointegration of the prosthesis. Varying stem designs provide surgeons with multiple options to gain femoral fixation. OBJECTIVE: The purpose of this study was to compare the initial fixation stability of cylindrical and tapered stem implants using two different underreaming techniques (press-fit conditions) for revision total hip arthroplasty (THA). METHODS: A finite element femur model was created from three-dimensional computed tomography images simulating a trabecular bone defect commonly observed in revision THA. Two 18-mm generic femoral hip implants were modeled using the same geometry, differing only in that one had a cylindrical stem and the other had a 2 degree tapered stem. Surgery was simulated using a 0.05-mm and 0.01-mm press-fit and tested with a physiologically relevant loading protocol. RESULTS: Mean contact pressure was influenced more by the surgical technique than by the stem geometry. The 0.05-mm press-fit condition resulted in the highest contact pressures for both the cylindrical (27.35 MPa) and tapered (20.99 MPa) stems. Changing the press-fit to 0.01-mm greatly decreased the contact pressure by 79.8% and 78.5% for the cylindrical (5.53 MPa) and tapered (4.52 MPa) models, respectively. The cylindrical stem geometry consistently showed less relative micromotion at all the cross-sections sampled as compared to the tapered stem regardless of press-fit condition. CONCLUSIONS: This finite element analysis study demonstrates that tapered stem results in lower average contact pressure and greater micromotion at the implant-bone interface than a cylindrical stem geometry. More studies are needed to establish how these different stem geometries perform in such non-ideal conditions encountered in revision THA cases where less bone stock is available.

Comparing the Knotless Tension Band and the Traditional Stainless Steel Wire Tension Band Fixation for Medial Malleolus Fractures: A Retrospective Clinical Study.

The traditional stainless steel wire tension band (WTB) has been popularized for small avulsion fractures at the medial malleolus. Despite the tension band principle creating a stable construct, complications continue to arise utilizing the traditional stainless steel WTB with patients experiencing hardware irritation at the tension band site and subsequent hardware removal. Coupled with hardware irritation is fatigue failure with the wire. The goal of this investigation was to retrospectively compare this traditional wire technique to an innovative knotless tension band (KTB) technique in order to decrease costly complications. A total of 107 patients were reviewed with a minimum follow-up of 1 year. Outcome measures include descriptive data, fracture classification, results through economic costs, and fixation results (including hardware status, healing status, pain status, and time to healing). The KTB group had a 13% lower true cost as compared to the WTB group while the fixation results were equivocal for the measured outcomes. Our results demonstrate that the innovative KTB is comparable to the traditional WTB while offering a lower true cost, an irritation free reduction all without the frustration of returning to the operating room for additional hardware removal, which averages approximately to $8,288.

Restoring lumbar spine stiffness using an interspinous implant in an ovine model of instability.

BACKGROUND: The objective of this study was to determine the effect of an interspinous implant on lumbar spine stability and stiffness during dorsoventral loading. METHODS: Twelve Merino lambs were mechanically tested in vivo. Oscillatory (2 Hz) loads were applied to L2 under load control while displacements were monitored. Tri-axial accelerometers further quantified adjacent L3-L4 accelerations. Dorsoventral lumbar spine stiffness and L3 and L4 dorsoventral and axial displacements were determined over six trials of 20 cycles of loading. Four conditions were examined: 1) initial intact, 2) following destabilization at L3-L4, 3) following the insertion of an InSwing(®) interspinous device at L3-L4, and 4) with the implant secured with a tension band. Comparisons were performed using a one-way ANOVA with repeated measures and post-hoc Bonferroni correction. FINDINGS: Compared to the intact condition, destabilization significantly decreased lumbar stiffness by 4.5% (P=.001) which was only recovered by the interspinous device with tension band. The interspinous device caused a significant 9.75% (P=.001) increase in dorsoventral stiffness from destabilization that increased 14% with the tension band added (P=.001). The tension band was responsible for decreased displacements from the intact (P=.038), instability (P=.001), and interspinous device (P=.005) conditions. Dorsoventral L3-L4 motion significantly improved with the interspinous device (P=.01) and the addition of the tension band (P=.001). No significant differences in L3-L4 intersegmental stability were noted for axial motion in the sagittal plane. INTERPRETATION: This ovine model provided objective in vivo biomechanical evidence of lumbar instability and its restoration by means of an interspinous implant during dorsoventral spinal loading.

Effect of Posterior Tibial Slope on Flexion and Anterior-Posterior Tibial Translation in Posterior Cruciate-Retaining Total Knee Arthroplasty.

Reduced posterior tibial slope (PTS) and posterior tibiofemoral translation (PTFT) in posterior cruciate-retaining (PCR) total knee arthroplasty (TKA) may result in suboptimal flexion. We evaluated the relationship between PTS, PTFT, and total knee flexion after PCR TKA in a cadaveric model. We performed a balanced PCR TKA using 9 transfemoral cadaver specimens and changed postoperative PTS in 1° increments. We measured maximal flexion and relative PTFT at maximal flexion. We determined significant changes in flexion and PTFT as a function of PTS. Findings showed an average increase in flexion of 2.3° and average PTFT increase of 1mm per degree of PTS increase when increasing PTS from 1° to 4° (P<.05). Small initial increases in PTS appear to significantly increase knee flexion and PTFT.

Fully Threaded Versus Partially Threaded Screws: Determining Shear in Cancellous Bone Fixation.

Many researchers have studied and compared various forms of intraosseous fixation. No studies have examined the effects of shear through stiffness and failure strength of a fully threaded versus a partially threaded screw. Our hypothesis was that the fully threaded lag screw technique would provide greater shear strength and resistance. Thirty-six synthetic sawbone blocks were used to test screw fixation. In group 1 (n = 9), 2 blocks were fixed together using a fully threaded 4.0-mm stainless steel cancellous bone screw and the lag technique. In group 2 (n = 8), 2 blocks were fixed together using the standard manufacturer-recommended method for inserting 4.0-mm partially threaded stainless steel cancellous bone screws. The constructs were then mechanically tested. Shear was applied by compressing each construct at an axial displacement rate of 0.5 mm/s until failure. The fully threaded screw had a significantly greater (p = .026) initial stiffness (106.4 ± 15.8 N/mm) than the partially threaded screw (80.1 ± 27.5 N/mm). The yield load and displacement for the fully threaded group (429.4 ± 11.7 N and 7.2 ± 0.35 mm) were 64% and 67% greater than those for the partially threaded screw group (261.4 ± 26.1 N and 4.3 ± 1.03 mm), respectively. The results of the present study have demonstrated the importance of a full-thread construct to prevent shear and to decrease strain at the fracture. The confirmation of our hypothesis questions the future need and use of partially threaded screws for cancellous bone fixation.

Two novel high performing composite PMMA-CaP cements for vertebroplasty: An ex vivo animal study.

There is a growing body of the literature on new cement formulations that address the shortcomings of PMMA bone cements approved for use in vertebroplasty (VP) and balloon kyphoplasty (BKP). The present study is a contribution to these efforts by further characterization of two pre-mixed CaP filler-reinforced PMMA bone cements intended for VP; namely, PMMA-HA and PMMA-brushite cements. Each of these cements showed acceptable levels of various properties determined in porcine vertebral bodies. These properties included radiographic contrast, maximum exotherm temperature setting time, cement extravasation, stiffness change after fatigue loading, change of VB height after fracture following fatigue loading, and interdigitation. Each property value was comparable to or better than that for a PMMA bone cement approved for use in BKP. Thus, the results for the composite bone cements are promising.

Dual small fragment plating improves screw-to-screw load sharing for mid-diaphyseal humeral fracture fixation: a finite element study.

BACKGROUND: A smaller humerus in some patients makes the use of a large fragment fixation plate difficult. Dual small fragment plate constructs have been suggested as an alternative. OBJECTIVE: This study compares the biomechanical performance of three single and one dual plate construct for mid-diaphyseal humeral fracture fixation. METHODS: Five humeral shaft finite element models (1 intact and 4 fixation) were loaded in torsion, compression, posterior-anterior (PA) bending, and lateral-medial (LM) bending. A comminuted fracture was simulated by a 1-cm gap. Fracture fixation was modelled by: (A) 4.5-mm 9-hole large fragment plate (wide), (B) 4.5-mm 9-hole large fragment plate (narrow), (C) 3.5-mm 9-hole small fragment plate, and (D) one 3.5-mm 9-hole small fragment plate and one 3.5-mm 7-hole small fragment plate. RESULTS: Model A showed the best outcomes in torsion and PA bending, whereas Model D outperformed the others in compression and LM bending. Stress concentrations were located near and around the unused screw holes for each of the single plate models and at the neck of the screws just below the plates for all the models studied. Other than in PA bending, Model D showed the best overall screw-to-screw load sharing characteristics. CONCLUSION: The results support using a dual small fragment locking plate construct as an alternative in cases where crutch weight-bearing (compression) tolerance may be important and where anatomy limits the size of the humerus bone segment available for large fragment plate fixation.

Characterization of a new composite PMMA-HA/Brushite bone cement for spinal augmentation.

Calcium phosphate fillers have been shown to increase cement osteoconductivity, but have caused drawbacks in cement properties. Hydroxyapatite and Brushite were introduced in an acrylic two-solution cement at varying concentrations. Novel composite bone cements were developed and characterized using rheology, injectability, and mechanical tests. It was hypothesized that the ample swelling time allowed by the premixed two-solution cement would enable thorough dispersion of the additives in the solutions, resulting in no detrimental effects after polymerization. The addition of Hydroxyapatite and Brushite both caused an increase in cement viscosity; however, these cements exhibited high shear-thinning, which facilitated injection. In gel point studies, the composite cements showed no detectable change in gel point time compared to an all-acrylic control cement. Hydroxyapatite and Brushite composite cements were observed to have high mechanical strengths even at high loads of calcium phosphate fillers. These cements showed an average compressive strength of 85 MPa and flexural strength of 65 MPa. A calcium phosphate-containing cement exhibiting a combination of high viscosity, pseudoplasticity and high mechanical strength can provide the essential bioactivity factor for osseointegration without sacrificing load-bearing capability.

Preparation and Characterization of Injectable Brushite Filled-Poly (Methyl Methacrylate) Bone Cement.

Powder-liquid poly (methyl methacrylate) (PMMA) bone cements are widely utilized for augmentation of bone fractures and fixation of orthopedic implants. These cements typically have an abundance of beneficial qualities, however their lack of bioactivity allows for continued development. To enhance osseointegration and bioactivity, calcium phosphate cements prepared with hydroxyapatite, brushite or tricalcium phosphates have been introduced with rather unsuccessful results due to increased cement viscosity, poor handling and reduced mechanical performance. This has limited the use of such cements in applications requiring delivery through small cannulas and in load bearing. The goal of this study is to design an alternative cement system that can better accommodate calcium-phosphate additives while preserving cement rheological properties and performance. In the present work, a number of brushite-filled two-solution bone cements were prepared and characterized by studying their complex viscosity-versus-test frequency, extrusion stress, clumping tendency during injection through a syringe, extent of fill of a machined void in cortical bone analog specimens, and compressive strength. The addition of brushite into the two-solution cement formulations investigated did not affect the pseudoplastic behavior and handling properties of the materials as demonstrated by rheological experiments. Extrusion stress was observed to vary with brushite concentration with values lower or in the range of control PMMA-based cements. The materials were observed to completely fill pre-formed voids in bone analog specimens. Cement compressive strength was observed to decrease with increasing concentration of fillers; however, the materials exhibited high enough strength for consideration in load bearing applications. The results indicated that partially substituting the PMMA phase of the two-solution cement with brushite at a 40% by mass concentration provided the best combination of the properties investigated. This alternative material may find applications in systems requiring highly injectable and viscous cements such as in the treatment of spinal fractures and bone defects.

Dual plating of humeral shaft fractures: orthogonal plates biomechanically outperform side-by-side plates.

BACKGROUND: Single large-fragment plate constructs currently are the norm for internal fixation of middiaphyseal humerus fractures. In cases where humeral size is limited, however, dual small-fragment locking plate constructs may serve as an alternative. The mechanical effects of different possible plate configurations around the humeral diaphysis may be important, but to our knowledge, have yet to be investigated. QUESTIONS/PURPOSES: We used finite element analysis to compare the simulated mechanical performance of five different dual small-fragment locking plate construct configurations for humeral middiaphyseal fracture fixation in terms of (1) stiffness, (2) stress shielding of bone, (3) hardware stresses, and (4) interfragmentary strain. METHODS: Middiaphyseal humeral fracture fixation was simulated using the finite element method. Three 90° and two side-by-side seven-hole and nine-hole small-fragment dual locking plate configurations were tested in compression, torsion, and combined loading. The configurations chosen are based on implantation using either a posterior or anterolateral approach. RESULTS: All three of the 90° configurations were more effective in restoring the intact compressive and torsional stiffness as compared with the side-by-side configurations, resulted in less stress shielding and stressed hardware, and showed interfragmentary strains between 5% to 10% in torsion and combined loading. CONCLUSIONS: The nine-hole plate anterior and seven-hole plate lateral (90° apart) configuration provided the best fixation. Our findings show the mechanical importance of plate placement with relation to loading in dual-plate fracture-fixation constructs. CLINICAL RELEVANCE: The results presented provide novel biomechanical information for the orthopaedic surgeon considering different treatment options for middiaphyseal humeral fractures.

A biomechanical investigation of a knotless tension band in medial malleolar fracture models in composite Sawbones®.

The present study introduces a knotless tension band construct and compares its biomechanical behavior with that of a traditional stainless steel tension band construct. Fourth-generation composite tibial Sawbones(®) were used in the present study. Fracture models were created to mimic Orthopaedic Trauma Association type 44-B2.2 ankle fractures. A total of 20 specimens were randomized evenly into a stainless steel tension band group (control group); or a knotless tension band group. The fixation constructs were mechanically tested, and the stiffness and failure strengths were calculated. Two failure strengths were determined: the engineering-based failure strength, defined as the greatest tensile load tolerated by the construct; and the clinical failure strength, defined as the force required to displace the fracture by 2 mm. We used 2-tailed independent samples t tests to compare and identify significant differences. The knotless tension band construct was 7.7% stronger and 33.2% stiffer and required a 36.7% greater force to displace the fracture by 2 mm. Independent sample t tests confirmed that differences in mean stiffness (p = .003) and clinical failure strength (p = .003) were statistically significant. Although the mean engineering strength for the knotless group was greater than that for the stainless steel group, this difference was not statistically significant (p = .170). This knotless tension band construct could potentially offer both clinical and biomechanical advantages compared with the current stainless steel standard.

Effects of comprehensive osteopathic manipulative treatment on balance in elderly patients: a pilot study.

CONTEXT: Falls, many of which are caused by balance problems, are a leading cause of injuries in elderly persons. Few studies have investigated osteopathic manipulative treatment (OMT) for patients with balance problems. OBJECTIVE: To test whether an OMT protocol with an emphasis on cranial manipulation can improve vestibular balance control structures and postural stability in a healthy elderly population. DESIGN: A pilot prospective clinical trial. SETTING: Research laboratories of the University of North Texas Health Science Center Texas College of Osteopathic Medicine in Fort Worth. PATIENTS: Forty healthy elderly patients aged 65 or older were enrolled and separated into an OMT group and a control group. Owing to the recruitment process and limited time for the study, the first 20 patients to enroll were in the OMT group, and the next 20 were in the control group. Patients were excluded if they had a condition that could impair balance. INTERVENTION: The OMT protocol comprised 7 OMT techniques applied weekly by the same osteopathic physician before balance tests. Patients in the control group received no treatment. MAIN OUTCOME MEASURES: Patients were asked to stand on a force plate and to perform 3 balance tests: (1) eyes open, (2) eyes closed, and (3) a modified Romberg test. The center of pressure between their feet was recorded for 30 seconds. The average center of pressure displacement for each test was used to determine anteroposterior (AP) sway and mediolateral (ML) sway. Balance tests were performed each week for 4 weeks. Tests were performed at the same time of day as the first test. RESULTS: Changes in AP sway values between visits 1 and 4 were as follows: eyes open, -0.72 and 0.75 mm for the control and OMT groups, respectively; eyes closed, -0.49 and 0.44 mm; and Romberg test, -0.17 and 0.52 mm. The changes in ML sway values between visits 1 and 4 were as follows: eyes open, -0.58 and 0.07 mm for the control and OMT groups, respectively; eyes closed, -0.21 and 0.03 mm; and Romberg test, -0.15 and 0.39 mm. The OMT group had significantly reduced sway for the eyes-open test after 4 visits (P=.001). CONCLUSION: The OMT protocol used in the present study improved the postural stability of healthy elderly patients, as measured by changes in sway values. (ClinicalTrials.gov number NCT01153412).

Gliding resistance and triggering after venting or A2 pulley enlargement: a study of intact and repaired flexor tendons in a cadaveric model.

PURPOSE: This study compared the effect of 2 techniques of pulley management--venting and pulley enlargement (complete A2 incision with pulley repair and sheath closure using a retinacular graft)--on gliding resistance and on the incidence of triggering following zone 2 flexor tendon repairs in human cadaver specimens. METHODS: In vitro gliding resistance and the incidence of triggering were determined in 10 human cadaver specimens under 5 progressive conditions: (1) intact, (2) tendon repair (both tendons cut and repaired with the sheath intact), (3) condition 2 plus 50% venting of the distal A2 pulley, (4) condition 2 with venting extended to 66% of distal A2, and (5) condition 4 plus pulley enlargement. Triggering was determined in the same specimens by 2 computational algorithms that detected force changes in the load cells used to measure gliding resistance. RESULTS: Tendon repair increased gliding resistance from the intact condition by an average of 229%. Gliding resistance was reduced in conditions 3, 4, and 5 from the repair condition by 15%, 25%, and 22%, respectively. Triggering commenced with tendon repair in some specimens, and its incidence increased with 50% venting. Further venting reduced triggering, but not as effectively as pulley enlargement did. CONCLUSIONS: In this cadaveric study, venting and pulley enlargement reduce gliding resistance by equivalent amounts. Triggering persisted despite venting. The surgeon should carefully examine tendon repairs for free gliding. Pulley enlargement might be more effective than venting in reducing the incidence of triggering.

Management of a post-operative multi-resistant infectious spondylitis associated with a kyphotic deformity.

Anterior spinal infection (prevertebral abscess and/or discitis) after posterior instrumentation for vertebral fractures is a challenging complication, since a new implant may become necessary anteriorly, in a septic environment. Generally accepted management guidelines are yet to be established. The authors present a case of posterior instrumentation for fractures of T12 and L1, complicated after 9 months with an anterior infection (prevertebral abscess and discitis) with extended-spectrum beta-lactamase (ESBL) producing Escherichia coli (E. coli). This case is unique in that the multi-resistant organism was isolated only after the second stage of infection treatment, which consisted of anterior débridement and anterior implantation of titanium cages and rods. In this particular case, infection was controlled despite implantation of multiple cages, screws and rods, and fusion was achieved, by means of intravenous antibiotic treatment for 12 months. At the latest follow-up, 24 months post surgery, there was no evidence of infection. This problem case may be helpful for surgeons confronted with spinal deformities secondary to infections with multi-resistant organisms.

Primary tendon sheath enlargement and reconstruction in zone 2: an in vitro biomechanical study on tendon gliding resistance.

PURPOSE: To investigate our hypothesis that primary pulley enlargement and repair using an extensor retinaculum graft will reduce tendon repair gliding resistance. The benefit of pulley enlargement has been tested in experimental animals, but its effect on gliding resistance in vitro using human fingers is not known. METHODS: In vitro gliding resistance in the proximal tendon sheaths (A1 through A3) was measured and compared in 7 cadaver fingers using the method of Uchiyama and colleagues at a fixed 50 degrees over the proximal sheath under 3 conditions: (1) intact tendons with intact proximal sheath; (2) laceration and 2-strand core plus running epitenon repair of the tendons with intact sheath; and (3) repaired tendons with enlargement of the A2 pulley and adjacent proximal sheath by incision and repair with an extensor retinacular graft. Results were analyzed statistically. RESULTS: Gliding resistance increased from an average of 0.44 N +/- 0.07 in the intact condition to an average of 1.51 N +/- 0.23 (a mean increase of 243%) when the tendons were cut and repaired. Enlarging the proximal sheath by sheath incision and graft repair reduced the gliding resistance from the repair condition to 1.04 N +/- 0.15 (a mean decrease of 31%). These changes are statistically significant. CONCLUSIONS: In vitro, repaired tendons had a greater resistance to gliding than that of the intact tendons through the proximal sheath when tested by the method of Uchiyama and colleagues. Enlargement and repair with an extensor retinacular graft of the A2 pulley and adjacent sheath significantly reduced resistance to repaired tendon gliding. These findings support further investigation into the concept that primary pulley enlargement may improve tendon function after repair.

Effect of a novel interspinous implant on lumbar spinal range of motion.

Interspinous devices have been introduced to provide a minimally invasive surgical alternative for patients with lumbar spinal stenosis or foraminal stenosis. Little is known however, of the effect of interspinous devices on intersegmental range of motion (ROM). The aim of this in vivo study was to investigate the effect of a novel minimally invasive interspinous implant, InSwing, on sagittal plane ROM of the lumbar spine using an ovine model. Ten adolescent Merino lambs underwent a destabilization procedure at the L1-L2 level simulating a stenotic degenerative spondylolisthesis (as described in our earlier work; Spine 15:571-576, 1990). All animals were placed in a side-lying posture and lateral radiographs were taken in full flexion and extension of the trunk in a standardized manner. Radiographs were repeated following the insertion of an 8-mm InSwing interspinous device at L1-L2, and again with the implant secured by means of a tension band tightened to 1 N/m around the L1 and L2 spinous processes. ROM was assessed in each of the three conditions and compared using Cobb's method. A paired t-test compared ROM for each of the experimental conditions (P < 0.05). After instrumentation with the InSwing interspinous implant, the mean total sagittal ROM (from full extension to full flexion) was reduced by 16% from 6.3 degrees to 5.3 +/- 2.7 degrees. The addition of the tension band resulted in a 43% reduction in total sagittal ROM to 3.6 +/- 1.9 degrees which approached significance. When looking at flexion only, the addition of the interspinous implant without the tension band did not significantly reduce lumbar flexion, however, a statistically significant 15% reduction in lumbar flexion was observed with the addition of the tension band (P = 0.01). To our knowledge, this is the first in vivo study radiographically showing the advantage of using an interspinous device to stabilize the spine in flexion. These results are important findings particularly for patients with clinical symptoms related to instable degenerative spondylolisthesis.