Effect of using households' information and communication technology on CO2 emissions-empirical evidence of the city of Novi Sad.

Globally, the carbon footprint (CF) is constantly increasing, contrasting with the decreasing trend observed for decades in the European Union (EU) countries, where EU guidelines are responsibly followed and outlined in its strategic documents. Information and communication technology (ICT) carbon emissions have historically increased in parallel with global emissions, contributing to continuous increases in ICT's CF over time, even when excluding full life cycle emissions. This study examines the impact of ICT on household electricity consumption, aiming to quantify the potential reduction of greenhouse gas (GHG) emissions through improved household energy efficiency. The methodology includes the data collection on ICT device usage in households within the city of Novi Sad (Republic of Serbia), employing the survey method that queries respondents on device quantities and their usage patterns. This study provides results for decision-makers to recognize concrete benefits from the transition to a circular economy (CE) and low-carbon emissions, which are reflected as benefits for the local community and socio-economic environment.

Natural Rubber Composites Using Hydrothermally Carbonized Hardwood Waste Biomass as a Partial Reinforcing Filler-Part II: Mechanical, Thermal and Ageing (Chemical) Properties.

Natural rubber composites were reinforced by the co-fillers 'hydrochar' (HC), obtained by hydrothermal carbonization of hardwood sawdust and commercial carbon black (CB). The content of the combined fillers was kept constant while their ratio was varied. The aim was to test the suitability of HC as a partial filler in natural rubber. Due to its larger particle size and hence smaller specific surface area, large amounts of HC reduced the crosslinking density in the composites. On the other hand, due to its unsaturated organic character, HC was found to display interesting chemical effects: if it was used as the exclusive filler component, it displayed a very strong anti-oxidizing effect, which greatly stabilized the rubber composite against oxidative crosslinking (and hence embrittlement). HC also affected the vulcanization kinetics in different ways, depending on the HC/CB ratio. Composites with HC/CB ratios 20/30 and 10/40 displayed interesting chemical stabilization in combination with fairly good mechanical properties. The performed analyses included vulcanization kinetics, tensile properties, determination of density of permanent and reversible crosslinking in dry and swollen states, chemical stability tests including TGA, thermo-oxidative aging tests in air at 180 °C, simulated weathering in real use conditions ('Florida test'), and thermo-mechanical analyses of degraded samples. Generally, the results indicate that HC could be a promising filler material due to its specific reactivity.

A Novel Approach for Simulation and Optimization of Rubber Vulcanization.

The kinetic model, encompassing the curing and reversion phenomena of the NR/SBR rubber vulcanization process, was developed by means of the finite element method simultaneously with heat transfer equations, including heat generation due to curing reactions. The vulcanization simulation was conducted for three spheres of different diameters (1, 5 and 10 cm) and two rubber wheels, one of which was a commercial product of the rubber industry. The proposed advanced simulation model, based on products' two-dimensional axisymmetry, includes cooling after vulcanization, during which the crosslinking reactions continue to take place as a result of the products' heated interiors. As a criterion for removing the product from the mold, an average vulcanization degree of 0.9 was set, whereby, during cooling, the vulcanization degree increases, due to crosslinking reactions. Based on the minimal difference between the maximal and minimal vulcanization degrees, which did not exceed a value of 0.0142, the optimal process parameters for each product were determined, achieving homogeneity and obtaining high-quality rubber products, while simultaneously ensuring a more efficient vulcanization process and enhanced cost effectiveness for the rubber industry.

Natural Rubber Composites Using Hydrothermally Carbonized Hardwood Waste Biomass as a Partial Reinforcing Filler- Part I: Structure, Morphology, and Rheological Effects during Vulcanization.

A new generation biomass-based filler for natural rubber, 'hydrochar' (HC), was obtained by hydrothermal carbonization of hardwood waste (sawdust). It was intended as a potential partial replacement for the traditional carbon black (CB) filler. The HC particles were found (TEM) to be much larger (and less regular) than CB: 0.5-3 µm vs. 30-60 nm, but the specific surface areas were relatively close to each other (HC: 21.4 m2/g vs. CB: 77.8 m2/g), indicating a considerable porosity of HC. The carbon content of HC was 71%, up from 46% in sawdust feed. FTIR and 13C-NMR analyses indicated that HC preserved its organic character, but it strongly differs from both lignin and cellulose. Experimental rubber nanocomposites were prepared, in which the content of the combined fillers was set at 50 phr (31 wt.%), while the HC/CB ratios were varied between 40/10 and 0/50. Morphology investigations proved a fairly even distribution of HC and CB, as well as the disappearance of bubbles after vulcanization. Vulcanization rheology tests demonstrated that the HC filler does not hinder the process, but it significantly influences vulcanization chemistry, canceling scorch time on one hand and slowing down the reaction on the other. Generally, the results suggest that rubber composites in which 10-20 phr of CB are replaced by HC might be promising materials. The use of HC in the rubber industry would represent a high-tonnage application for hardwood waste.