Faraday isolator for a 100 J/10 Hz pulsed laser.

We report the first-ever, to the best of our knowledge, demonstration of the optical isolation of a kilowatt average power pulsed laser. A Faraday isolator capable of stable protection of the laser amplifier chain delivering 100 J nanosecond laser pulses at the repetition rate of 10 Hz has been developed and successfully tested. The isolator provided an isolation ratio of 30.46 dB in the course of an hour-long testing run at full power without any noticeable decrease due to the thermal effects. This is the first-ever, to the best of our knowledge, demonstration of a nonreciprocal optical device operated with such a powerful high-energy, high-repetition-rate laser beam, opening up the possibilities for this type of laser to be used for a number of industrial and scientific applications.

Silicon Brewster plate wavelength separator for a mid-IR optical parametric source.

The availability of optical elements for the mid-infrared wavelength range, such as polarizers and wavelength separators, is limited especially when a broadband wavelength range coverage is required. We propose a polarizer based on uncoated silicon Brewster plates. A detailed analysis of the polarizer's contrast and the influence of parasitic reflections, its dependence on wavelength, and the angular misalignment is shown. Two different arrangements of the two- and four-plate polarizers are discussed. With contrast including the influence of parasitic reflections of over 103 for the whole transparency range of silicon (1.2-6.5 µm), the four-plate polarizer is an effective, low-cost, high-power compatible tool providing sufficient contrast for signal and idler beam separation of the broadband mid-infrared Type II optical parametric sources. The proposed polarizers can function as an attenuator assembly without any wave plate.

Faraday Rotation of Dy2O3, CeF3 and Y3Fe5O12 at the Mid-Infrared Wavelengths.

The relatively narrow choice of magneto-active materials that could be used to construct Faraday devices (such as rotators or isolators) for the mid-infrared wavelengths arguably represents a pressing issue that is currently limiting the development of the mid-infrared lasers. Furthermore, the knowledge of the magneto-optical properties of the yet-reported mid-infrared magneto-active materials is usually restricted to a single wavelength only. To address this issue, we have dedicated this work to a comprehensive investigation of the magneto-optical properties of both the emerging (Dy2O3 ceramics and CeF3 crystal) and established (Y3Fe5O12 crystal) mid-infrared magneto-active materials. A broadband radiation source was used in a combination with an advanced polarization-stepping method, enabling an in-depth analysis of the wavelength dependence of the investigated materials' Faraday rotation. We were able to derive approximate models for the examined dependence, which, as we believe, may be conveniently used for designing the needed mid-infrared Faraday devices for lasers with the emission wavelengths in the 2-µm spectral region. In the case of Y3Fe5O12 crystal, the derived model may be used as a rough approximation of the material's saturated Faraday rotation even beyond the 2-µm wavelengths.

Large-Beam Picosecond Interference Patterning of Metallic Substrates.

In this paper, we introduce a method to efficiently use a high-energy pulsed 1.7 ps HiLASE Perla laser system for two beam interference patterning. The newly developed method of large-beam interference patterning permits the production of micro and sub-micron sized features on a treated surface with increased processing throughputs by enlarging the interference area. The limits for beam enlarging are explained and calculated for the used laser source. The formation of a variety of surface micro and nanostructures and their combinations are reported on stainless steel, invar, and tungsten with the maximum fabrication speed of 206 cm2/min. The wettability of selected hierarchical structures combining interference patterns with 2.6 µm periodicity and the nanoscale surface structures on top were analyzed showing superhydrophobic behavior with contact angles of 164°, 156°, and 150° in the case of stainless steel, invar, and tungsten, respectively.

Spectroscopy and diode-pumped laser operation of transparent Tm:Lu3Al5O12 ceramics produced by solid-state sintering.

A transparent Tm:Lu3Al5O12 ceramic is fabricated by solid-state reactive sintering at 1830 °C for 30 h using commercial α-Al2O3 and Lu2O3/Tm2O3 powders and sintering aids - MgO and TEOS. The ceramic belongs to the cubic system and exhibits a close-packed structure (mean grain size: 21 µm). The in-line transmission at ∼1 µm is 82.6%, close to the theoretical limit. The spectroscopic properties of the ceramic are studied in detail. The maximum stimulated-emission cross-section is 2.37×10-21 cm2 at 1749nm and the radiative lifetime of the 3F4 state is about 10 ms. The modified Judd-Ofelt theory accounting for configuration interaction is applied to determine the transition probabilities of Tm3+, yielding the intensity parameters Ω2 = 2.507, Ω4 = 1.236, Ω6 = 1.340 [10-20 cm2] and α = 0.196×10-4 cm. The effect of excited configurations on lower-lying interconnected states with the same J quantum number is discussed. First laser operation is achieved under diode-pumping at 792 nm. A 4 at.% Tm:Lu3Al5O12 ceramic laser generated 3.12 W at 2022-2035nm with a slope efficiency of 60.2%. The ceramic is promising for multi-watt lasers at >2 µm.

Experimental study on compression of 216-W laser pulses below 2 ps at 1030 nm with chirped volume Bragg grating.

We report on the characterization of a high-power, chirped volume Bragg grating (CVBG) pulse compressor. It includes measurements of the CVBG's diffraction efficiency, beam profile, beam quality (M2 parameter), pulse spectrum, the CVBG's temperature, and the thermal lens. These parameters were monitored for a wide range of input laser powers and with different clamping forces applied on the CVBG. This analysis was performed with a CPA-based Yb:YAG thin-disk laser system operating at a wavelength of 1030 nm, a 92 kHz repetition rate, 2 ps pulse duration, and an average output power after compression of 216 W (270 W uncompressed), which is, to the best of our knowledge, the highest value reported to date using this pulse compression technique.

Micromachining of Invar with 784 Beams Using 1.3 ps Laser Source at 515 nm.

To fulfil the requirements for high-resolution organic light-emitting diode (OLED) displays, precise and high-quality micrometer-scale patterns have to be fabricated inside metal shadow masks. Invar has been selected for this application due to its unique properties, especially a low coefficient of thermal expansion. In this study, a novel cost-efficient method of multi-beam micromachining of invar will be introduced. The combination of a Meopta beam splitting, focusing and monitoring module with a galvanometer scanner and HiLASE high-energy pulse laser system emitting ultrashort pulses at 515 nm allows drilling and cutting of invar foil with 784 beams at once with high precision and almost no thermal effects and heat-affected zone, thus significantly improving the throughput and efficiency.

Verdet constant of potassium terbium fluoride crystal as a function of wavelength and temperature.

Potassium terbium fluoride KTb3F10 (KTF) crystal is a promising magneto-active material for creating multi-kilowatt average-power Faraday isolators operating at the visible and near-infrared wavelengths. Nevertheless, the key material's parameter needed for the design of any Faraday isolator-the Verdet constant, has not been comprehensively investigated yet. In this Letter, we report on measurement of the Verdet constant of the KTF crystal for wavelengths between 600 and 1500 nm and for temperatures ranging from 15 to 295 K. A suitable model for the Verdet constant as a function of wavelength and temperature has been developed and may be conveniently used for optimal design of KTF-based high-average-power Faraday isolators.

Novel unstable resonator configuration for highly efficient cryogenically cooled Yb:YAG Q-switched laser.

A novel method to shape the intensity distribution within an unstable laser cavity is demonstrated. This method is characterized by inscribing a tailored gain profile generated by a spatially tophat-shaped longitudinal pump beam into the gain medium. The mode shaping mechanism is still effective with zero output coupling. Therefore, this method enables to operate unstable laser cavities in cavity dump mode or as a regenerative amplifier. The theoretical background is described by means of geometrical optics, and operation of a prototype setup using cryogenically cooled Yb:YAG is demonstrated. The system produces 13ns pulses with 285 mJ at a repetition rate of 10 Hz, with an extraction efficiency of 35 %. Successful cavity dump operation is demonstrated with 110 mJ output energy.

Passive Q switching of Yb:CNGS lasers by Cr4+:YAG and V3+:YAG saturable absorbers.

Trigonal langasite-type ordered silicate crystal Yb:Ca3NbGa3Si2O14 (Yb:CNGS) is a promising material for efficient ∼1 µm lasers. We report on the first passively Q-switched Yb:CNGS laser using Cr4+:YAG and V3+:YAG saturable absorbers (SAs) with a 976 nm volume-Bragg-grating-stabilized diode as a pump source. The laser crystal was a c cut 3 at.% Yb:CNGS grown by the Czochralski method. It was placed in a compact microchip-type laser cavity. With a Cr4+:YAG SA, very stable 62.2 µJ/4.4 ns pulses were achieved at a repetition rate of 22.5 kHz. The average output power was 1.40 W at 1015.3 nm, corresponding to a Q switching conversion efficiency of 90%. With the V3+:YAG SA, the pulse characteristics were 13.3 µJ/11.1 ns at a higher repetition rate of 68.4 kHz. The performance of the Yb:CNGS/Cr4+:YAG was numerically modeled showing a good agreement with the experiment.

Fs-laser-written erbium-doped double tungstate waveguide laser.

We report on the first erbium (Er3+) doped double tungstate waveguide laser. As a gain material, we studied a monoclinic Er3+:KLu(WO4)2 crystal. A depressed-index buried channel waveguide formed by a 60 µm-diameter circular cladding was fabricated by 3D femtosecond direct laser writing. The waveguide was characterized by confocal laser microscopy, µ-Raman and µ-luminescence mapping, confirming that the crystallinity of the core is preserved. The waveguide laser, diode pumped at 981 nm, generated 8.9 mW at 1533.6 nm with a slope efficiency of 20.9% in the continuous-wave regime. The laser polarization was linear (E || Nm). The laser threshold was at 93 mW of absorbed pump power.

Efficient diode-pumped Er:KLu(WO4)2 laser at ∼1.61 µm.

We report on an efficient diode-pumped continuous-wave erbium-doped monoclinic double tungstate laser. It is based on a 1 at. % Er3+:KLu(WO4)2 (Er:KLuW) crystal cut along the Ng optical indicatrix axis. The Er:KLuW microchip laser, diode pumped at 0.98 µm, generates 268 mW at 1.610 µm with a slope efficiency of 30%. The output is linearly polarized (E||Nm), and the laser beam is nearly diffraction limited (Mp,m2<1.1). Spectroscopic properties of Er3+ in KLuW are also presented. The stimulated-emission cross-section σSE is 0.46×10-20 cm2 at ∼1.609 µm for E||Nm. The microchip Er:KLuW laser outperforms the commercial Er,Yb:glass.

Continuous-wave and passively Q-switched cryogenic Yb:KLu(WO4)2 laser.

We study cryogenic laser operation of an Yb-doped KLu(WO4)2 crystal pumped with a volume Bragg grating (VBG) stabilized diode laser at 981 nm. In the continuous wave laser regime, a maximum output power of 4.31 W is achieved at 80 K with a slope efficiency of 44.0% with respect to the incident pump power. Using a 85% initial transmission Cr:YAG crystal for passive Q-switching, an average output power of 2.11 W is achieved at 100 K for a repetition rate of 19 kHz. The pulse energy, pulse duration and peak power amount to 111 µJ, 231 ns and 0.48 kW, respectively.

Microchip Yb:CaLnAlO4 lasers with up to 91% slope efficiency.

Multi-watt continuous-wave (CW) operation of tetragonal rare-earth calcium aluminate Yb:CaLnAlO4(Ln=Gd,Y)) crystals in plano-plano microchip lasers was demonstrated with an almost quantum-defect-limited slope efficiency. Pumped at 978 nm by an InGaAs laser diode, a 3.4 mm long 8 at. % Yb:CaGdAlO4 laser generated 7.79 W at 1057-1065 nm with a slope efficiency of η=84% (with respect to the absorbed pump power). An even higher η=91% was achieved with a 2.5 mm long 3 at. % Yb:CaYAlO4 laser, from which 5.06 W were extracted at 1048-1056 nm. Both lasers produced linearly polarized output (σ-polarization) with an almost circular diffraction-limited beam (Mx,y2<1.1). The output performance of the developed lasers was modeled, yielding an internal loss coefficient as low as 0.004-0.007 cm-1. In addition, their spectroscopic properties were revisited.

100 J-level nanosecond pulsed diode pumped solid state laser.

We report on the successful demonstration of a 100 J-level, diode pumped solid state laser based on cryogenic gas cooled, multi-slab ceramic Yb:YAG amplifier technology. When operated at 175 K, the system delivered a pulse energy of 107 J at a 1 Hz repetition rate and 10 ns pulse duration, pumped by 506 J of diode energy at 940 nm, corresponding to an optical-to-optical efficiency of 21%. To the best of our knowledge, this represents the highest energy obtained from a nanosecond pulsed diode pumped solid state laser. This demonstration confirms the energy scalability of the diode pumped optical laser for experiments laser architecture.

Wavelength dependence of magneto-optic properties of terbium gallium garnet ceramics.

The wavelength dependence of magneto-optic properties of TGG ceramics, including the Verdet constant, has been investigated experimentally. The previously obtained Verdet constant of 36.4 rad/Tm for 1064 nm wavelength and 139.6 rad/Tm for 633 nm are in good agreement with presented white light measurements . The comparison with previously reported Verdet constant and absorption coefficient values for TGG single crystal has shown very similar results. These results lead to the conclusion that TGG ceramics is a very good alternative to TGG single crystal and is a powerful approach for realizing large-aperture optical isolators which are required in high-average-power laser systems.

1-J operation of monolithic composite ceramics with Yb:YAG thin layers: multi-TRAM at 10-Hz repetition rate and prospects for 100-Hz operation.

Experimental amplification of 10-ns pulses to energy of 1 J at repetition rate of 10-100 Hz in cryogenic multipass total-reflection active-mirror (TRAM) amplifier is reported for the first time. By using a monolithic multi-TRAM, which is a YAG ceramic composite with three thin Yb:YAG active layers, efficient energy extraction was achieved without parasitic lasing. A detailed measurement of output characteristics of the laser amplifier is presented; results are discussed and compared with numerical calculations.

Design and optimization of an adaptive optics system for a high-average-power multi-slab laser (HiLASE).

We report numerical and experimental results obtained with an optical setup that simulates the heating and cooling processes expected in a multi-slab high-average-power laser head. We have tested the performance of an adaptive optics system consisting of a photo-controlled deformable mirror (PCDM) and a Shack-Hartmann wavefront sensor for the effective correction of the generated wavefront aberrations. The performance of the adaptive optics system is characterized for different layouts of the actuator array and for different configurations of the heating mechanisms. The numerical results are benchmarked using a PCDM, which allowed us to experimentally compare the performances of different deformable mirrors.

Thermal effects in the Input Optics of the Enhanced Laser Interferometer Gravitational-Wave Observatory interferometers.

We present the design and performance of the LIGO Input Optics subsystem as implemented for the sixth science run of the LIGO interferometers. The Initial LIGO Input Optics experienced thermal side effects when operating with 7 W input power. We designed, built, and implemented improved versions of the Input Optics for Enhanced LIGO, an incremental upgrade to the Initial LIGO interferometers, designed to run with 30 W input power. At four times the power of Initial LIGO, the Enhanced LIGO Input Optics demonstrated improved performance including better optical isolation, less thermal drift, minimal thermal lensing, and higher optical efficiency. The success of the Input Optics design fosters confidence for its ability to perform well in Advanced LIGO.

Active-mirror-laser-amplifier thermal management with tunable helium pressure at cryogenic temperatures.

We illustrate the benefits of a thin, low pressure helium cell for efficient and safe heat removal in cryogenically-cooled active mirror laser amplifiers operating in the [100 J-1 kJ]/[1-10 Hz] range. A homogeneous gain medium temperature distribution averaging 160 K is obtained with a sub-mm helium-filled gap between the gain medium and a copper plate at 77 K. A significant degree of flexibility for tuning the temperature in the amplifier can be achieved by varying the pressure of the helium gas in the 10(2) to 10(5) Pa range.