Microfracture technique combined with mesenchymal stem cells inducer represses miR-708-5p to target special at-rich sequence-binding protein 2 to drive cartilage repair and regeneration in rabbit knee osteoarthritis.

Knee osteoarthritis (KOA) is a degenerative joint illness which leads to knee pain and functional limitation. In this study, we combined microfracture surgery with kartogenin (KGN), a small bioactive molecule used to promote the differentiation of mesenchymal stem cells (MSCs), and explored its impact on cartilage repair and possible latent mechanisms of action. The research offers a brand-new idea for the clinical cure of KOA. The microfracture technique in combination with KNG treatment was performed on a rabbit model of KOA. Animal behaviour was evaluated after the intra-articular injection of miR-708-5p and Special AT-rich sequence binding protein 2 (SATB2) lentiviruses. Later, the expression of the tumour necrosis factor α (TNF-α) and interleukin- 1 (IL-1), the pathology of synovial tissue and cartilage tissue, and the positive cartilage type II collagen, MMP-1, MMP-3 and TIMP-1 were detected. Finally, a luciferase assay was conducted to verify the interaction of miR-708-5p and SATB2. Our results showed that miR-708-5p was elevated in the rabbit KOA model; however, the expression of SATB2 was reduced. Meanwhile, the microfracture technology combined with MSCs inducer KGN drove cartilage repair and regeneration in rabbit KOA by repressing the miR-708-5p expression. We also found that miR-708-5p directly targeted the SATB2 mRNA to regulate its expression. Furthermore, our data urged that elevating miR-708-5p or restraining SATB2 may reverse the therapeutic effect of the microfracture technique combined with MSCs inducer on rabbit KOA. Microfracture technique combined with MSCs inducer represses miR-708-5p to target SATB2 to drive cartilage repair and regeneration in rabbit KOA. This indicates that the microfracture technique combined with MSCs inducers is supposed to be an effective latent method for osteoarthritis cure.

Design and localization algorithm of flap guide plate for jaw defect based on digital 3D printing.

The anterolateral thigh flap is often used to repair the wound tissue defect. Because it is difficult to carry out the perforating vessels before and after the operation, it is considered to use digital design combined with 3D printing technology to prepare the digital three-dimensional guide plate, and at the same time, the guide plate positioning algorithm is designed according to the error caused by the different placement of the guide plate at the site to be transplanted. First of all, select the patients with jaw defect, make the patient's jaw model, obtain the corresponding plaster working model through 3D scanning, obtain STL data, design the guide plate in combination with Rihnoceros and other software, and print the flap guide plate corresponding to jaw defect with the help of metal powder using 3D printer. Based on sequential CT images, the localization algorithm takes the improved genetic algorithm as the research object, extracts the information of the transplantation area as the parameter space, codes the parameters such as the coordinates of the end points of the flap transplantation, and constructs the target function and fitness function of the transplantation. In the experiment, the soft tissue of the patients with jaw defects can be well repaired based on the guide plate. The positioning algorithm locates the flap graft under the condition of less environmental parameters, and obtains the corresponding diameter parameters.

Feasibility of polyethylene composites reinforced by distillers dried fibers with solubles (DDFS) after different generations of ethanol fermentation.

In order to effectively evaluate the distillers dried fibers with solubles (DDFS) obtained from biorefinery processes, sorghum distiller (SD), cassava distiller (CD) and corn cob distiller (CCD) residuals from different generation bioethanol plants were used as the reinforcing phase for polyethylene composites. The mechanical performances and the physical properties of the polyethylene/DDFS composites were evaluated. The results showed that the CCD reinforced specimen offered the best mechanical performances, with a flexural strength of 21.8 ± 2.2 MPa and a tensile strength of 39.7 ± 3.2 MPa. After multigelation, the retention ratios of the rupture modulus and the elasticity modulus of the CCD reinforced specimen reached 88.7 ± 6.7% and 84.1 ± 2.7%, while after 2000 h of xenon lamp weathering they reached 96.2 ± 4.7% and 82 ± 1.8%, respectively. Hybridizing the biorefinery process with the process of composites production was feasible.

Effect of dilute alkaline pretreatment on the conversion of different parts of corn stalk to fermentable sugars and its application in acetone-butanol-ethanol fermentation.

To investigate the effect of dilute alkaline pretreatment on different parts of biomass, corn stalk was separated into flower, leaf, cob, husk and stem, which were treated by NaOH in range of temperature and chemical loading. The NaOH-pretreated solid was then enzymatic hydrolysis and used as the substrate for batch acetone-butanol-ethanol (ABE) fermentation. The results demonstrated the five parts of corn stalk could be used as potential feedstock separately, with vivid performances in solvents production. Under the optimized conditions towards high product titer, 7.5g/L, 7.6g/L, 9.4g/L, 7g/L and 7.6g/L of butanol was obtained in the fermentation broth of flower, leaf, cob, husk and stem hydrolysate, respectively. Under the optimized conditions towards high product yield, 143.7g/kg, 126.3g/kg, 169.1g/kg, 107.7g/kg and 116.4g/kg of ABE solvent were generated, respectively.

Effect of acid pretreatment on different parts of corn stalk for second generation ethanol production.

In this study, the effects of different parts of corn stalk, including stem, leaf, flower, cob and husk on second generation ethanol production were evaluated. FTIR, XRD and SEM were performed to investigate the effect of dilute acid pretreatment. The bagasse obtained after pretreatment were further hydrolyzed by cellulase and used as the substrate for ethanol fermentation. As results, hemicelluloses fractions in different parts of corn stalk were dramatically removed and the solid fractions showed vivid compositions and crystallinities. Compared with other parts of corn stalk, the cob had higher sugar content and better enzymatic digestibility. The highest glucose yield of 94.2% and ethanol production of 24.0 g L(-1) were achieved when the cob was used as feedstock, while the glucose yield and the ethanol production were only 86.0% and 17.1 g L(-1) in the case of flower.