Monolithic Use of Inert Gas for Highly Transparent and Conductive Indium Tin Oxide Thin Films.

Due to its excellent electrical conductivity, high transparency in the visible spectrum, and exceptional chemical stability, indium tin oxide (ITO) has become a crucial material in the fields of optoelectronics and nanotechnology. This article provides a thorough analysis of growing ITO thin films with various thicknesses to study the impact of thickness on their electrical, optical, and physical properties for solar-cell applications. ITO was prepared through radio frequency (RF) magnetron sputtering using argon gas with no alteration in temperature or changes in substrate heating, followed with annealing in a tube furnace under inert conditions. An investigation of the influence of thickness on the optical, electrical, and physical properties of the films was conducted. We found that the best thickness for ITO thin films was 100 nm in terms of optical, electrical, and physical properties. To gain full comprehension of the impact on electrical properties, the different samples were characterized using a four-point probe and, interestingly, we found a high conductivity in the range of 1.8-2 × 106 S/m, good resistivity that did not exceed 1-2 × 10-6 Ωm, and a sheet resistance lower than 16 Ω sq-1. The transparency values found using a spectrophotometer reached values beyond 85%, which indicates the high purity of the thin films. Atomic force microscopy indicated a smooth morphology with low roughness values for the films, indicating an adequate transitioning of the charges on the surface. Scanning electron microscopy was used to study the actual thicknesses and the morphology, through which we found no cracks or fractures, which implied excellent deposition and annealing. The X-ray diffraction microscopy results showed a high purity of the crystals, as the peaks (222), (400), (440), and (622) of the crystallographic plane reflections were dominant, which confirmed the existence of the faced-center cubic lattice of ITO. This work allowed us to design a method for producing excellent ITO thin films for solar-cell applications.

Shape-Stabilized PEGylated Silica Aerogel-Composite as an Energy Saving Building Material.

Balancing thermal and visual comfort in buildings necessitates effective insulation to counteract heat loss and gain, especially with temperature variances. One promising approach is to combine phase change materials, such as poly(ethylene glycol) (PEG), with high-performance insulators like silica aerogel (Siag). To bolster opto-thermal performance in building envelopes, we introduce a smart insulation composite material through PEG integration, i.e., PEGalyation with Siag. Central to this thermal behavior is the PEG's phase change properties, which foster a shape-stabilized framework with Siag through their porous confinement. Preliminary observations indicate notable capabilities of obstructing near-infrared light while preserving satisfactory visible transparency. An optimized Siag@PEG composite with 5% loading of PEG has the visible range transmission of ∼92%, a decrease of ∼72% in thermal conductivity which is lower than pure glass and PEG, leading to a temperature dependent switchable hydrophobic to hydrophilic wettability characteristics. As a prototype window, the thermal performance evaluation of the synthesized composite, through experimental and computational studies, shows a decrease in indoor temperature of ∼20% with a higher temperature difference of ∼20 °C between outdoor and indoor weather conditions. This lightweight composite can act as sponge media to fill inside the double-paned window and for retrofitting existing glazing to boost the energy efficiency of buildings with facile manufacturing and scalability.

Advancing Thermoelectric Materials: A Comprehensive Review Exploring the Significance of One-Dimensional Nano Structuring.

Amidst the global challenges posed by pollution, escalating energy expenses, and the imminent threat of global warming, the pursuit of sustainable energy solutions has become increasingly imperative. Thermoelectricity, a promising form of green energy, can harness waste heat and directly convert it into electricity. This technology has captivated attention for centuries due to its environmentally friendly characteristics, mechanical stability, versatility in size and substrate, and absence of moving components. Its applications span diverse domains, encompassing heat recovery, cooling, sensing, and operating at low and high temperatures. However, developing thermoelectric materials with high-performance efficiency faces obstacles such as high cost, toxicity, and reliance on rare-earth elements. To address these challenges, this comprehensive review encompasses pivotal aspects of thermoelectricity, including its historical context, fundamental operating principles, cutting-edge materials, and innovative strategies. In particular, the potential of one-dimensional nanostructuring is explored as a promising avenue for advancing thermoelectric technology. The concept of one-dimensional nanostructuring is extensively examined, encompassing various configurations and their impact on the thermoelectric properties of materials. The profound influence of one-dimensional nanostructuring on thermoelectric parameters is also thoroughly discussed. The review also provides a comprehensive overview of large-scale synthesis methods for one-dimensional thermoelectric materials, delving into the measurement of thermoelectric properties specific to such materials. Finally, the review concludes by outlining prospects and identifying potential directions for further advancements in the field.

Effectual visible light photocatalytic reduction of para-nitro phenol using reduced graphene oxide and ZnO composite.

Removing wastewater pollutants using semiconducting-based heterogeneous photocatalysis is an advantageous technique because it provides strong redox power charge carriers under sunlight irradiation. In this study, we synthesized a composite of reduced graphene oxide (rGO) and zinc oxide nanorods (ZnO) called rGO@ZnO. We established the formation of type II heterojunction composites by employing various physicochemical characterization techniques. To evaluate the photocatalytic performance of the synthesized rGO@ZnO composite, we tested it for reducing a common wastewater pollutant, para-nitro phenol (PNP), to para-amino phenol (PAP) under both ultraviolet (UV) and visible light irradiances. The rGOx@ZnO (x = 0.5-7 wt%) samples, comprising various weights of rGO, were investigated as potential photocatalysts for the reduction of PNP to PAP under visible light irradiation. Among the samples, rGO5@ZnO exhibited remarkable photocatalytic activity, achieving a PNP reduction efficiency of approximately 98% within a short duration of four minutes. These results demonstrate an effective strategy and provide fundamental insights into removing high-value-added organic water pollutants.

Effect of novel graphitic carbon/NiO hole transporting electrode on the photovoltaic and optical performance of semi-transparent perovskite solar cells.

Perovskite devices can play a critical role as tunable semi-transparent photovoltaics managing the buildings' energy health for energy harvesting, storage and utilization. Here we report ambient semi-transparent PSCs with novel graphitic carbon/NiO-based hole transporting electrodes having variable thicknesses achieving a highest efficiency of ∼14%. On the other hand, the altered thickness produced the highest average visible transparency (AVT) of the devices, nearly 35%, which also influenced other glazing-related parameters. This study envisages the impact of the electrode deposition technique on indispensable parameters like colour rendering index, correlated colour temperature, and solar factor evaluated using theoretical models to illuminate these CPSCs' colour and thermal comfort for BIPV integration. The solar factor value between 0 to 1, CRI value >80 and CCT value >4000 K make it a significant semi-transparent device. This research work suggests a possible approach to fabricating carbon-based PSC for high-performance semi-transparent solar cells.

Certified high-efficiency "large-area" perovskite solar module for Fresnel lens-based concentrated photovoltaics.

The future of energy generation is well in tune with the critical needs of the global economy, leading to more green innovations and emissions-abatement technologies. Introducing concentrated photovoltaics (CPVs) is one of the most promising technologies owing to its high photo-conversion efficiency. Although most researchers use silicon and cadmium telluride for CPV, we investigate the potential in nascent technologies, such as perovskite solar cell (PSC). This work constitutes a preliminary investigation into a "large-area" PSC module under a Fresnel lens (FL) with a "refractive optical concentrator-silicon-on-glass" base to minimize the PV performance and scalability trade-off concerning the PSCs. The FL-PSC system measured the solar current-voltage characteristics in variable lens-to-cell distances and illuminations. The PSC module temperature was systematically studied using the COMSOL transient heat transfer mechanism. The FL-based technique for "large-area" PSC architectures is a promising technology that further facilitates the potential for commercialization.

Nigeria's energy review: Focusing on solar energy potential and penetration.

In Nigeria, the rapid population increase and the overreliance on fossil fuel have created significant environmental, health, political, and economic consequences leading to severe socio-economic drawbacks. These factors have developed a wide gap between energy demand and supply due to insufficient local production, necessitating a clean energy supply for all. The photovoltaic device's economic and environmental merits have made it the most suitable clean energy alternative to help developing countries such as Nigeria achieve the SDG-7. However, apart from the device's low efficiency, which is undergoing intensive study globally, other factors affect the penetration of the technology in developing countries, particularly Nigeria. This report systematically reviews the literature on the country's energy crisis and renewable energy potential, leading to an overview of solar energy potential and penetration. The potential of the technology and its penetration in the country were provided. A list highlighting challenges hindering technology penetration was also provided, and a solution for each was recommended.

Nanoparticles to Enhance Melting Performance of Phase Change Materials for Thermal Energy Storage.

The present study proposes the phase change material (PCM) as a thermal energy storage unit to ensure the stability and flexibility of solar-energy-based heating and cooling systems. A mathematical model is developed to evaluate the PCM melting process, considering the effect of nanoparticles on heat transfer. We evaluate the role of nanoparticles (Al2O3-, copper- and graphene-based nanofluids) in enhancing the performance of the melting process of phase change materials. The results show that natural convection due to the buoyancy effect dominates the flow behaviour even in the initial stage of the PCM melting process. High natural convection at the bottom of the annular tube moves the melted PCM upward from the lateral, which pushes the liquid-solid interface downward. The addition of 3% vol Al2O3 nanoparticles boosts PCM melting performance by decreasing the melting time of PCM by approximately 15%. The comparison of Al2O3, copper and graphene nanoparticles demonstrates that higher thermal conductivity, ranging from 36 to 5000 W m-1 K-1, does not contribute to a significant improvement in the melting performance of PCMs.

Development of Morphologically engineered Flower-like Hafnium-Doped ZnO with Experimental and DFT Validation for Low-Temperature and Ultrasensitive Detection of NOX Gas.

Substitutional doping and different nanostructures of ZnO have rendered it an effective sensor for the detection of volatile organic compounds in real-time atmosphere. However, the low selectivity of ZnO sensors limits their applications. Herein, hafnium (Hf)-doped ZnO (Hf-ZnO) nanostructures are developed by the hydrothermal method for high selectivity of hazardous NOX gas in the atmosphere, substantially portraying the role of doping concentration on the enhancement of structural, optical, and sensing behavior. ZnO microspheres with 5% Hf doping showed excellent sensing and detected 22 parts per billion (ppb) NOX gas in the atmosphere, within 24 s, which is much faster than ZnO (90 s), and rendered superior sensing ability (S = 67) at a low temperature (100 °C) compared to ZnO (S = 40). The sensor revealed exceptional stability under humid air (S = 55 at 70% RH), suggesting a potential of 5% Hf-ZnO as a new stable sensing material. Density functional theory (DFT) and other characterization analyses revealed that the high sensing activity of 5% Hf-ZnO is attributed to the accessibility of more adsorption sites arising due to charge distortion, increased oxygen vacancies concentration, Lewis acid base, porous morphology, small particle size (5 nm), and strong bond interaction amidst NO2 molecule with ZnO-Hf-Ovacancy sites, resulting from the substitution of the host cation (Zn2+) with doping cation (Hf4+).

Synergistic Effect of Paraffin-Incorporated In2O3/ZnO Multifold Smart Glazing Composite for the Self-Cleaning and Energy-Saving Built Environment.

The thermal performance of window glazing requires improvement for a sustainable built environment at an acceptable cost. The current work demonstrates a multifold smart composite consisting of an optimized In2O3/ZnO-polymethyl methacrylate-paraffin composite to reduce heat exchange through the combined self-cleaning and energy-saving envelope of the smart built environment. This work has attempted to develop a smart composite coating that combines photosensitive metal oxide and phase change materials and investigate their thermal comfort performance as a glazed window. It is observed that the In2O3/ZnO (5 wt %) multifold composite film experienced better transmittance and thermal performance compared to its other wt % composite samples. Moreover, the multifold composite-coated glass integrated into a prototype glazed window was further investigated for its thermal performance, where a steady average indoor temperature of ∼30 °C was achieved when the outside temperature reached ∼55 °C, while maintaining good visibility. Interestingly, the transparency reached ∼86% at 60 °C and exhibited a hydrophobic water contact angle (WCA) of ∼138°. In contrast, a similar film exhibits ∼64% transparency at 22 °C, where the WCA becomes moderately hydrophilic (∼68°). Temperature dependency on transparency and wettability properties was examined for up to 60 cycles, resulting in excellent indoor thermal comfort. In addition, a thermal simulation study was executed for the smart multifold glazing composite. Moreover, this study offers dynamic glazing development options for energy saving in the smart built environment.

Cotton soot derived carbon nanoparticles for NiO supported processing temperature tuned ambient perovskite solar cells.

The emergence of perovskite solar cells (PSCs) in a "catfish effect" of other conventional photovoltaic technologies with the massive growth of high-power conversion efficiency (PCE) has given a new direction to the entire solar energy field. Replacing traditional metal-based electrodes with carbon-based materials is one of the front-runners among many other investigations in this field due to its cost-effective processability and high stability. Carbon-based perovskite solar cells (c-PSCs) have shown great potential for the development of large scale photovoltaics. First of its kind, here we introduce a facile and cost-effective large scale carbon nanoparticles (CNPs) synthesis from mustard oil assisted cotton combustion for utilization in the mesoporous carbon-based perovskite solar cell (PSC). Also, we instigate two different directions of utilizing the carbon nanoparticles for a composite high temperature processed electrode (HTCN) and a low temperature processed electrode (LTCN) with detailed performance comparison. NiO/CNP composite thin film was used in high temperature processed electrodes, and for low temperature processed electrodes, separate NiO and CNP layers were deposited. The HTCN devices with the cell structure FTO/c-TiO2/m-TiO2/m-ZrO2/high-temperature NiO-CNP composite paste/infiltrated MAPI (CH3NH3PbI3) achieved a maximum PCE of 13.2%. In addition, high temperature based carbon devices had remarkable stability of ~ 1000 h (ambient condition), retaining almost 90% of their initial efficiency. In contrast, LTCN devices with configuration FTO/c-TiO2/m-TiO2/m-ZrO2/NiO/MAPI/low-temperature CNP had a PCE limit of 14.2%, maintaining ~ 72% of the initial PCE after 1000 h. Nevertheless, we believe this promising approach and the comparative study between the two different techniques would be highly suitable and adequate for the upcoming cutting-edge experimentations of PSC.

Reduced graphene oxide (rGO) aerogel: Efficient adsorbent for the elimination of antimony (III) and (V) from wastewater.

3D porous, thin sheet-like rGO aerogel was fabricated to explore its antimony (Sb) removal potential from wastewater. Langmuir isothermal and pseudo-second-order kinetic model best-suited the adsorption process. The maximum adsorption capacities were 168.59 and 206.72 mg/g for Sb (III and V) at pH 6.0 respectively. The thermodynamic parameters designated the process to be thermodynamically spontaneous, endothermic reaction, a result of dissociative chemisorption. The rGO aerogel bestowed good selectively among competing ions and reusability with 95% efficiency. rGO posed excellent practicability with Sb-spiked tap water and fixed-bed column experiments showing 97.6% of Sb (III) (3.6 µg/L) and 96.8% of Sb (V) (4.7 µg/L) removal from tap water and from fixed column bed experiments breakthrough volumes (BV) for the Sb (III) and Sb (V) ions were noted to be 540 BV and 925 BV respectively, until 5 ppb, which are below the requirement of MCL for Sb in drinking water (6 µg/L). XPS and DFT analyses explained adsorption mechanism and depicted a higher affinity of Sb (V) towards rGO surface than Sb (III).

Role of Hafnium Doping on Wetting Transition Tuning the Wettability Properties of ZnO and Doped Thin Films: Self-Cleaning Coating for Solar Application.

Herein, we successfully synthesized high-quality Hf-ZnO thin films with various Hf contents (0, 3, 6, 9, 12, and 15 at. %), which showed both superhydrophilic (6% Hf-ZnO) and ultrahydrophobic (15% Hf-ZnO) wetting behavior. Different characterization methods were opted to recognize the structural (XRD, SEM, AFM) and defect properties (XPS) of the pristine and doped materials, to understand the mechanisms underlying the tuning of wetting behavior (contact angle). Hafnium doping plays a noteworthy role in tuning the morphology of the ZnO nanostructures, roughness of the material surface, generation of defects, Lewis acid-base interactions, and wettability properties. We achieved a superhydrophilic surface with 6% Hf-ZnO owing to a smooth surface, less basicity, and maximum concentration of oxygen vacancies, and also an ultrahydrophobic surface with 15% Hf-ZnO because of the rough surface, high basicity, and minimum concentration of oxygen vacancies. The as prepared Hf-ZnO samples showed stable performance (stability, wearability, weatherability, and antifouling) under real-life conditions marking them multifunctional and biosafe material to be effectively used in solar and building's window. A wetting mechanism was established to relate the wetting behavior of the samples to oxygen vacancies (active sites for water dissociation: resulted due to charge mismatch of host cation (Zn2+) by the doped cation (Hf4+)), roughness (smooth surface (Wenzel) with minimum Rrms (0.588) portraying hydrophilic property and rough caltropic surface (Cassie-Baxter) with maximum Rrms (2.522) portraying hydrophobic property), basicity (H2O: Lewis Base; ZnO: Lewis acid; HfO2: Lewis base) and morphology (tube-like structure (0-6% Hf-ZnO) and caltrop-like structure (12-15% Hf-ZnO)).

A Review on Heavy Metal Ions and Containing Dyes Removal Through Graphene Oxide-Based Adsorption Strategies for Textile Wastewater Treatment.

Textile wastewater heavy metal pollution has become a severe environmental problem worldwide. Metal ion inclusion in a dye molecule exhibits a bathochromic shift producing deeper but duller shades, which provides excellent colouration. The ejection of a massive volume of wastewater containing heavy metal ions such as Cr (VI), Pb (II), Cd (II) and Zn (II) and metal-containing dyes are an unavoidable consequence because the textile industry consumes large quantities of water and all these chemicals cannot be combined entirely with fibres during the dyeing process. These high concentrations of chemicals in effluents interfere with the natural water resources, cause severe toxicological implications on the environment with a dramatic impact on human health. This article reviewed the various metal-containing dye types and their heavy metal ions pollution from entryway to the wastewater, which then briefly explored the effects on human health and the environment. Graphene-based absorbers, specially graphene oxide (GO) benefits from an ordered structured, high specific surface area, and flexible surface functionalization options, which are indispensable to realize a high performance of heavy metal ion removal. These exceptional adsorption properties of graphene-based materials support a position of ubiquity in our everyday lives. The collective representation of the textile wastewater's effective remediation methods is discussed and focused on the GO-based adsorption methods. Understanding the critical impact regarding the GO-based materials established adsorption portfolio for heavy metal ions removal are also discussed. Various heavy-metal ions and their pollutant effect, ways to remove such heavy metal ions and role of graphene-based adsorbent including their demand, perspective, limitation, and relative scopes are discussed elaborately in the review.

Emplacement of screen-printed graphene oxide coating for building thermal comfort discernment.

This study demonstrates the development of flexible graphene oxide coatings (GOCs) by the screen-printed technique and further its implementation as a thermal absorber for buildings' thermal comfort purpose. The basic concept consists the integration of the GOC as a flat absorber on the top of a low iron glass or aluminium-based substrate (5 × 5 cm2) connecting through a phase change material channel in contact with direct sun exposure. The function of GOC as an outdoor cover of the prototype chamber is to maintain the high indoor temperature while the outdoor temperature is low. Using the GOC, it has been observed that the indoor temperature (at the substrate) of the prototype chamber always remains higher as compared to the outdoor temperature (at the GOC) as measured under 1 SUN 1.5 AM condition. The temperature difference between outdoor and indoor exterior surface significantly increases during the light exposure time, whereas the difference drastically approaches to zero during the cooling period. The variation of different crucial environmental factors such as high temperature, moisture, flexibility and water resistivity has been investigated on the developed GOCs to understand the stability of the coating further.

Study of COVID-19 pandemic in London (UK) from urban context.

COVID-19 transmission in London city was discussed in this work from an urban context. The association between COVID-19 cases and climate indicators in London, UK were analysed statistically employing published data from national health services, UK and Time and Date AS based weather data. The climatic indicators included in the study were the daily averages of maximum and minimum temperatures, humidity, and wind speed. Pearson, Kendall, and Spearman rank correlation tests were selected for data analysis. The data was considered up to two different dates to study the climatic effect (10th May in the first study and then updated up to 16th of July in the next study when the rest of the data was available). The results were contradictory in the two studies and it can be concluded that climatic parameters cannot solely determine the changes in the number of cases in the pandemic. Distance from London to four other cities (Birmingham, Leeds, Manchester, and Sheffield) showed that as the distance from the epicentre of the UK (London) increases, the number of COVID-19 cases decrease. What should be the necessary measure to be taken to control the transmission in cities have been discussed.

Realization of Poly(methyl methacrylate)-Encapsulated Solution-Processed Carbon-Based Solar Cells: An Emerging Candidate for Buildings' Comfort.

The self-assembling characteristics allow carbon nanomaterials to be readily explored, environmentally benign, solution-processed, low-cost, and efficient solar light-harvesting materials. An effort has been made to replace the regular photovoltaic device's electrodes by different carbon allotrope-based electrodes. Sequential fabrication of carbon solar cells (SCs) was performed under ambient conditions, where FTO/graphene/single-walled carbon nanotubes/graphene quantum dots-fullerene/carbon black paste layers were assembled with poly(methyl methacrylate) (PMMA) as an encapsulating layer. The PMMA layer provides significant improvement toward the entry of water vapor, hence leading to stability up to 1000 h. The photoconversion efficiency of the PMMA-encapsulated carbon SC has been increased by ∼105% and the stability decreased by only ∼10% after 1000 h of exposure to environmental moisture. Besides, the building integrated photovoltaic window properties achieved using this carbon SC were also investigated by using the color rendering index and the correlated color temperature, which can have an impact on the buildings' occupants' comfort. This study leads to an extensive integration to improve carbon-based materials because of their effective and useful but less-explored characteristics suitable for potential photovoltaic applications.

Incorporating Solution-Processed Mesoporous WO3 as an Interfacial Cathode Buffer Layer for Photovoltaic Applications.

Dextran-templating hydrothermal synthesis of monoclinic WO3 exhibits excellent specific surface area of ∼110 m2/g and a monomodal pore distribution with an average pore diameter of ∼20 nm. Dextran plays a crucial role in generating porosity on WO3. The role of supporting dextran has been investigated and found to be crucial to tune the surface area, porosity, and morphology. The photoluminescence and X-ray photoelectron spectroscopy studies reveal the existence of oxygen vacancies in substoichiometric WO3, which creates localized defect states in WO3 as synthesized through this templating method. The highly mesoporous WO3 has been further explored as an interfacial cathode buffer layer (CBL) in dye-sensitized solar cells (DSSCs) and perovskite solar cells (PSCs). A significantly enhanced photoconversion efficiency has boosted up the performance of the counter electrode used in traditional DSSC (as platinum) and PSC (as carbon) devices by ∼48 and ∼29%, respectively. The electrochemical impedance and incident photon to current conversion efficiency (IPCE) studies were also analyzed in order to understand the catalytic behavior of the WO3 interfacial CBL for both DSSCs and PSCs, respectively. The much higher surface area of WO3 enables rapid electron hopping mechanism, which further benefits for higher electron mobility, resulting in higher short circuit current. Through this study, we were able to unequivocally establish the importance of buffer layer incorporation, which can further help to integrate the DSSC and PSC devices toward more stable, reliable, and enhanced efficiency-generating devices. In spite of this, using WO3 constitutes an important step toward the efficiency improvement of the devices for futuristic photoelectrochromic or self-powered switchable glazing for low-energy adaptive building integration.

Performance of WO3-Incorporated Carbon Electrodes for Ambient Mesoscopic Perovskite Solar Cells.

The stability of perovskite solar cells (PSC) is often compromised by the organic hole transport materials (HTMs). We report here the effect of WO3 as an inorganic HTM for carbon electrodes for improved stability in PSCs, which are made under ambient conditions. Sequential fabrication of the PSC was performed under ambient conditions with mesoporous TiO2/Al2O3/CH3NH3PbI3 layers, and, on the top of these layers, the WO3 nanoparticle-embedded carbon electrode was used. Different concentrations of WO3 nanoparticles as HTM incorporated in carbon counter electrodes were tested, which varied the stability of the cell under ambient conditions. The addition of 7.5% WO3 (by volume) led to a maximum power conversion efficiency of 10.5%, whereas the stability of the cells under ambient condition was ∼350 h, maintaining ∼80% of the initial efficiency under light illumination. At the same time, the higher WO3 concentration exhibited an efficiency of 9.5%, which was stable up to ∼500 h with a loss of only ∼15% of the initial efficiency under normal atmospheric conditions and light illumination. This work demonstrates an effective way to improve the stability of carbon-based perovskite solar cells without affecting the efficiency for future applications.

Hydrophilic and Superhydrophilic Self-Cleaning Coatings by Morphologically Varying ZnO Microstructures for Photovoltaic and Glazing Applications.

Transparent, superhydrophilic materials are indispensable for their self-cleaning function, which has become an increasingly popular research topic, particularly in photovoltaic (PV) applications. Here, we report hydrophilic and superhydrophilic ZnO by varying the morphology for use as a self-cleaning coating for PV applications. Three different ZnO microstructures, such as ZnO nanorods (R-ZnO), ZnO microflowers (F-ZnO), and ZnO microspheres (M-ZnO), were developed by hydrothermal methods. The surface morphology by using X-ray diffraction (XRD), wettability behavior by using water contact angle (WCA) measurements, structural and optical properties by using photoluminescence (PL), Raman, and UV-vis spectrophotometry, and defect estimation by using X-ray photoelectron spectroscopy (XPS) of the ZnO nanostructured films were systematically investigated. XRD confirmed the formation of the hexagonal wurtzite structure of ZnO. The average crystallite sizes of prepared R-ZnO, F-ZnO, and M-ZnO were found to be 28.95, 11.19, and 41.5 nm, respectively. The band gap values of ZnO nanostructures were calculated from the UV-vis absorption spectrum and found to be 3.6, 3.3, and 3.1 eV for R-ZnO, F-ZnO, and M-ZnO, respectively. The WCAs for R-ZnO and F-ZnO were 20.2 and 11.19°, respectively, while M-ZnO behaved like a superhydrophilic material having a WCA of 2.8°.