Electrochemical determination of low levels of uranyl by a vibrating gold microelectrode.

In this work we report the sensitive electroanalytical detection of uranium(VI) in aqueous solutions. Uranium commonly exists in aqueous solutions in the form of its oxo ion, uranyl (U(VI)O2(2+)). The detection of uranyl has been accomplished by us through its deposition upon reduction by two electrons to the insoluble UO2 using a bare disk gold macroelectrode and anodic stripping voltammetry (ASV). This gave an unsatisfactory detection limit of ca. 1 × 10(-5) M uranyl. Moreover, the evolution of hydrogen bubbles blocked the electrode surface as a result of water reduction at negative deposition potential (-0.7 V vs Ag/AgCl). The application of a 25 µm diameter Au microwire electrode on which UO2 precipitated at negative potential (-1.2 V) improved substantially the detection limit. Further improvement was accomplished by vibrating the microwire working electrode, which increased the amounts of UO2 deposition due to decreasing the diffusion layer. The effect of the vibrating amplitude and frequency on the electroanalytical response was studied and optimized. Eventually, a detection limit of ca. 1 × 10(-9) M uranyl was achieved using a 5 min deposition time, -1.2 V deposition potential, and vibrating the electrode at frequency of 250 Hz and amplitude of 6 V.

Enhanced potentiometry by metallic nanoparticles.

Measuring the oxidation-reduction potential (Eh) requires an interface that is not selective toward specific species but exchanges electrons with all redox couples in the solution. Sluggish electron transfer (ET) kinetics with the species will not reflect the "true" Eh of the solution. Here, we present a novel approach by which adsorbed metal nanoparticles (NPs) are used for enhancing ET exchange rates between redox species and electrode surface and therefore affect significantly the measurement of the open circuit potential (OCP) and cyclic voltammetry (CV). The OCP and CV of various organic and inorganic species such as l-dopa, dopac, iron(II), and iodide are measured by bare stainless steel and by stainless steel modified by either Pt or Au NPs. We study the effect of the surface coverage of the stainless steel surface by NPs on the electrochemical response. Moreover, the stainless steel electrode was modified simultaneously by Au and Pt nanoparticles. This improved concurrently the stainless steel response (CV and potentiometry) toward two different species; l-dopa, which shows fast electron transfer on Pt, and catechol, which exhibits fast electron transfer on Au. We believe that this approach could be a first step toward developing a superior electrode for measuring the "true" Eh of complex aquatic systems.

Electrocoating of stainless steel coronary stents for extended release of paclitaxel.

Nonbiodegradable polymer coating based on N-(2-carboxyethyl)pyrrole (PPA) and butyl ester of PPA (BuOPy) were successfully electrodeposited on a stainless steel stent surface using cyclic voltammetry. Chemical composition of the coating was examined by X-ray photoelectron spectroscopy. Polymer stability was examined by immersing the coated stent into 1:1 solution of fetal calf serum:seline solution up to 1 year and implantation subcutaneously in mouse for 1 week. Morphology changes were then recorded by scanning electron microscopy. Paclitaxel loading was carried out by immersion into drug solution and its release was detected by HPLC. The results show that thin (single micrometers), uniform coating with various morphology and hydrophobicity can be created by electrochemical deposition. The polymer did not show significant histopathological or morphological changes in vitro and in vivo. The surface properties allow loading appropriate amounts of paclitaxel and release it slowly up to a month.

Disorganised self-assembled monolayers (SAMs): the incorporation of amphiphilic molecules.

A new approach for designing a voltammetric selective electrode is presented. The approach is based on the formation of a disorganised inert self-assembled monolayer (SAM), in which an amphiphilic molecule is incorporated. The latter serves as the selectivity factor, which extracts the analyte. The purpose of these experiments is to study the parameters that affect the capability of a monolayer to host amphiphiles. As model systems we focused on the incorporation of simple amphiphilic molecules (quaternary alkyl ammonium salts), electroactive amphiphiles (dialkylviologens) and a macrocycle ligand (tetramethylcyclam) into octadecyl silane monolayers formed on indium tin oxide (ITO) and purposely made disorganised alkanethiols on gold. We find that basically, the incorporation of amphiphiles into a hydrophobic inert SAM resembles a reversed stationary phase in liquid chromatography and this configuration can be used for designing selective electrodes.

Patterning and characterization of surfaces with organic and biological molecules by the scanning electrochemical microscope.

A novel approach for micropatterning of surfaces with organic and biological microstructures using the scanning electrochemical microscope (SECM) is described. The approach is based on the introduction of the spatial resolution by local deposition of gold particles followed by monolayer formation and functionalization. Specifically, gold patterns were deposited locally on silicon wafers with the SECM as a result of the controlled anodic dissolution of a gold microelectrode. The gold patterns were further used as microsubstrates for assembling cystamine monolayers to which either fluoresceine isothiocyanate (FIT) or glucose oxidase (GOD) were covalently attached. Characterization of the organic monolayers, as well as the biological activity of the enzyme patterns, was carried out by fluorescence microscopy and the SECM, respectively.

Scanning electrochemical microscopy. Theory of the feedback mode for hemispherical ultramicroelectrodes: steady-state and transient behavior

This contribution represents the first comprehensive attempt to treat complex geometry configurations of the scanning electrochemical microscope (SECM) using the alternating direction implicit finite difference method (ADIFDM). Specifically, ADIFDM is used to simulate the steady-state as well as the transient (chronoamperometric) behavior of a hemispherical ultramicroelectrode (UME) tip of the SECM. The feedback effect in this configuration is less pronounced as compared with a disk-shaped UME system. The differences between the two systems are discussed. Analytical approximations for the steady-state behavior and for characteristic features of the transient behavior are suggested. Finally, experimental feedback currents measured above a conductor and an insulator are in excellent agreement with the theory.

Visualization of sebaceous fingerprints on fired cartridge cases: a laboratory study.

The visualization and endurance of fingerprints on cartridge cases after the firing process have been examined. Cartridges of M16, AK-47 (Kalashnikov) and Parabellum have been tested. Despite difficulties in visualizing these fingerprints, it was found that in some cartridge cases under laboratory conditions--for instance, on M16 brass cartridges--substantial parts of the fingerprints remain intact after shooting. The careful use of illumination after metal vapor deposition enabled visualization. Different possible mechanisms responsible for the partial destruction of the fingerprints are discussed.

Selective Determination of Cr(VI) by a Self-Assembled Monolayer-Based Electrode.

We have developed a selective electrode for chromium(VI), based on a self-assembled monolayer of 4-(mercapto-n-alkyl)pyridinium on gold surfaces, which exhibits unique speciation capabilities. Cr(VI) levels as low as 1 parts per trillion can be detected using a 4-(mercaptoethyl)pyridinium monolayer. The different parameters that govern the analytical performance of these electrodes have been studied in detail and optimized. In addition, the organization of the monolayers has been examined by a variety of surface techniques such as XPS, FT-IR, and electrochemistry. Our results show that structuring and understanding the solid-liquid interface at the molecular level are essential for designing probes with superior analytical characteristics.