Physical and chemical properties and degradation of MAPbBr3 films on transparent substrates.

To date, the potential exploitation of hybrid organic-inorganic perovskites (HOIPs) in photovoltaic technologies has been significantly hampered by their poor environmental stability. HOIP degradation can be triggered by conventional operational environments, with excessive heating and exposure to oxygen and moisture significantly reducing the performances of HOIP-based solar cells. An imperative need emerges for a thorough investigation on the impact of these factors on the HOIP stability. In this work, the degradation of methylammonium lead bromide (CH3NH3PbBr3) thin films, deposited via spin-coating on indium tin oxide (ITO) and strontium titanate (STO) substrates, was investigated by combining Raman and ultraviolet-visible (UV-Vis) absorption spectroscopy, as well as optical and fluorescence microscopy. We assessed the physical and chemical degradation of the films occurring under diverse preservation conditions, shedding light on the byproducts emerging from different degradation pathways and on the optimal HOIP preservation conditions.

Direct detection of minimum ionizing charged particles in a perovskite single crystal detector with single particle sensitivity.

We report the detection of high energy electrons of some hundreds of MeV, crossing a methylammonium lead bromide single crystal device with sensitivity down to a single electron. In the device, the released energy is close to the energy released by minimum-ionizing particles. This is the first demonstration of a perovskite-based device that can be used for tracking and counting minimum-ionizing charged particles. The device reaches single particle sensitivity with a low bias voltage of 5 V. It also shows a good linearity of the response as a function of the number of electrons in a dynamic range of approximately 104.

Low-temperature strain-free encapsulation for perovskite solar cells and modules passing multifaceted accelerated ageing tests.

Perovskite solar cells promise to be part of the future portfolio of photovoltaic technologies, but their instability is slow down their commercialization. Major stability assessments have been recently achieved but reliable accelerated ageing tests on beyond small-area cells are still poor. Here, we report an industrial encapsulation process based on the lamination of highly viscoelastic semi-solid/highly viscous liquid adhesive atop the perovskite solar cells and modules. Our encapsulant reduces the thermomechanical stresses at the encapsulant/rear electrode interface. The addition of thermally conductive two-dimensional hexagonal boron nitride into the polymeric matrix improves the barrier and thermal management properties of the encapsulant. Without any edge sealant, encapsulated devices withstood multifaceted accelerated ageing tests, retaining >80% of their initial efficiency. Our encapsulation is applicable to the most established cell configurations (direct/inverted, mesoscopic/planar), even with temperature-sensitive materials, and extended to semi-transparent cells for building-integrated photovoltaics and Internet of Things systems.

Flexible, Transparent, and Bifacial Perovskite Solar Cells and Modules Using the Wide-Band Gap FAPbBr3 Perovskite Absorber.

Perovskite solar cells (PSCs) offer impressive performance and flexibility, thanks to their simple, low-temperature deposition methods. Their band gap tunability allows for a wide range of applications, transitioning from opaque to transparent devices. This study introduces the first flexible, bifacial PSCs using the FAPbBr3 perovskite. We investigated the impact of optimizing electron and hole transport layers on the cells' bifaciality, transparency, and stability. PSCs achieved a maximum power conversion efficiency (PCE) of 6.8 and 18.7% under 1 sun and indoor light conditions (1200 lx), respectively, showing up to 98% bifaciality factor and an average visible transmittance (AVT) of 55%. Additionally, a P1-P2-P3 laser ablation scheme has been developed on the flexible poly(ethylene terephthalate) (PET) substrate for perovskite solar modules showing a PCE of 4.8% and high geometrical fill factor (97.8%). These findings highlight the potential of flexible, bifacial PSCs for diverse applications such as building-integrated photovoltaics (BIPV), agrivoltaics, automotive technology, wearable sensors, and Internet of things (IoT).

Metal-Halide Perovskite Submicrometer-Thick Films for Ultra-Stable Self-Powered Direct X-Ray Detectors.

Metal-halide perovskites are revolutionizing the world of X-ray detectors, due to the development of sensitive, fast, and cost-effective devices. Self-powered operation, ensuring portability and low power consumption, has also been recently demonstrated in both bulk materials and thin films. However, the signal stability and repeatability under continuous X-ray exposure has only been tested up to a few hours, often reporting degradation of the detection performance. Here it is shown that self-powered direct X-ray detectors, fabricated starting from a FAPbBr3 submicrometer-thick film deposition onto a mesoporous TiO2 scaffold, can withstand a 26-day uninterrupted X-ray exposure with negligible signal loss, demonstrating ultra-high operational stability and excellent repeatability. No structural modification is observed after irradiation with a total ionizing dose of almost 200 Gy, revealing an unexpectedly high radiation hardness for a metal-halide perovskite thin film. In addition, trap-assisted photoconductive gain enabled the device to achieve a record bulk sensitivity of 7.28 C Gy-1 cm-3 at 0 V, an unprecedented value in the field of thin-film-based photoconductors and photodiodes for "hard" X-rays. Finally, prototypal validation under the X-ray beam produced by a medical linear accelerator for cancer treatment is also introduced.

Signatures of Polaron Dynamics in Photoexcited MAPbBr3 by Infrared Spectroscopy.

Hybrid organic-inorganic perovskites (HOIPs) have attracted considerable attention in the past years as photoactive materials for low-cost, high-performance photovoltaics. Polaron formation through electron-phonon coupling has been recognized as the leading mechanism governing charge carrier transport and recombination in HOIPs. In this work, two types of MAPbBr3 film samples deposited on different substrates (transparent insulating SrTiO3 and a heterostructure mimicking a functioning photovoltaic cell) were photoexcited with above-bandgap radiation at 450 nm, and the effects of illumination on the sample were analyzed in the infrared region. The infrared absorbance detected at different powers of the photoexciting laser allowed us to obtain an estimate of the characteristic decay time of photoexcited polaron population of the order of 100-1000 ns. When focusing on the absorption features of the MA molecular cation in the region of the NH stretching modes, we observed the influence of hydrogen bonding and the effect of the polaron dynamics on the cation reorientation.

Semitransparent Perovskite Solar Cells with Ultrathin Protective Buffer Layers.

Semitransparent perovskite solar cells (ST-PSCs) are increasingly important in a range of applications, including top cells in tandem devices and see-through photovoltaics. Transparent conductive oxides (TCOs) are commonly used as transparent electrodes, with sputtering being the preferred deposition method. However, this process can damage exposed layers, affecting the electrical performance of the devices. In this study, an indium tin oxide (ITO) deposition process that effectively suppresses sputtering damage was developed using a transition metal oxides (TMOs)-based buffer layer. An ultrathin (<10 nm) layer of evaporated vanadium oxide or molybdenum oxide was found to be effective in protecting against sputtering damage in ST-PSCs for tandem applications, as well as in thin perovskite-based devices for building-integrated photovoltaics. The identification of minimal parasitic absorption, the high work function and the analysis of oxygen vacancies denoted that the TMO layers are suitable for use in ST-PSCs. The highest fill factor (FF) achieved was 76%, and the efficiency (16.4%) was reduced by less than 10% when compared with the efficiency of gold-based PSCs. Moreover, up-scaling to 1 cm2-large area ST-PSCs with the buffer layer was successfully demonstrated with an FF of ∼70% and an efficiency of 15.7%. Comparing the two TMOs, the ST-PSC with an ultrathin V2Ox layer was slightly less efficient than that with MoOx, but its superior transmittance in the near infrared and greater light-soaking stability (a T80 of 600 h for V2Ox compared to a T80 of 12 h for MoOx) make V2Ox a promising buffer layer for preventing ITO sputtering damage in ST-PSCs.

Degradation and Self-Healing of FAPbBr3 Perovskite under Soft-X-Ray Irradiation.

The extensive use of perovskites as light absorbers calls for a deeper understanding of the interaction of these materials with light. Here, the evolution of the chemical and optoelectronic properties of formamidinium lead tri-bromide (FAPbBr3 ) films is tracked under the soft X-ray beam of a high-brilliance synchrotron source by photoemission spectroscopy and micro-photoluminescence. Two contrasting processes are at play during the irradiation. The degradation of the material manifests with the formation of Pb0 metallic clusters, loss of gaseous Br2 , decrease and shift of the photoluminescence emission. The recovery of the photoluminescence signal for prolonged beam exposure times is ascribed to self-healing of FAPbBr3 , thanks to the re-oxidation of Pb0 and migration of FA+ and Br- ions. This scenario is validated on FAPbBr3 films treated by Ar+ ion sputtering. The degradation/self-healing effect, which is previously reported for irradiation up to the ultraviolet regime, has the potential of extending the lifetime of X-ray detectors based on perovskites.

Holistic Approach toward a Damage-Less Sputtered Indium Tin Oxide Barrier Layer for High-Stability Inverted Perovskite Solar Cells and Modules.

The commercialization of perovskite solar cells (PSCs) requires the development of long-term, highly operational-stable devices. An efficient barrier layer plays a key role in improving the device stability of planar PSCs. Here, we focus on the use of sputtered indium tin oxide (ITO) as a barrier layer to stop major degradations. To mitigate efficiency losses of cells with the ITO barrier, we optimized various sputtering process parameters such as ITO layer thickness, target power density, and working pressure. The fabricated planar inverted PSCs based on the novel ITO barrier optimization demonstrate a power conversion efficiency (PCE) of 19.05% on a cell area of 0.09 cm2. The encapsulated cells retained >80% of their initial efficiency after 1400 h of continuous illumination at 55 °C and 94.5% of their initial PCE after 1500 h stored in air. Employing such a holistic stabilization approach, the PSC minimodules without encapsulation achieved an efficiency of 16.4% with a designated area of 2.28 cm2 and retained approximately 80% of the initial performance after thermal stress at 85 °C for 350 h under ambient conditions.

Optically Transparent Gold Nanoparticles for DSSC Counter-Electrode: An Electrochemical Characterization.

A gold nanoparticles transparent electrode was realized by chemical reduction. This work aims to compare the transparent gold nanoparticles electrode with a more commonly utilized gold-film-coated electrode in order to investigate its potential use as counter-electrode (CE) in dye-sensitized solar cells (DSSCs). A series of DSSC devices, utilizing I-/I3- and Co(III)/(II) polypyridine redox mediators [Co(dtb)3]3+/2+; dtb = 4,4'ditert-butyl-2,2'-bipyridine)], were evaluated. The investigation focused firstly on the structural characterization of the deposited gold layers and then on the electrochemical study. The novelty of the work is the realization of a gold nanoparticles CE that reached 80% of average visible transmittance. We finally examined the performance of the transparent gold nanoparticles CE in DSSC devices. A maximum power conversion efficiency (PCE) of 4.56% was obtained with a commercial I-/I3--based electrolyte, while a maximum 3.1% of PCE was obtained with the homemade Co-based electrolyte.

The Golden Fig: A Plasmonic Effect Study of Organic-Based Solar Cells.

An optimization work on dye-sensitized solar cells (DSSCs) based on both artificial and natural dyes was carried out by a fine synthesis work embedding gold nanoparticles in a TiO2 semiconductor and perfecting the TiO2 particle sizes of the scattering layer. Noble metal nanostructures are known for the surface plasmon resonance peculiarity that reveals unique properties and has been implemented in several fields such as sensing, photocatalysis, optical antennas and PV devices. By embedding gold nanoparticles in the mesoporous TiO2 layer and adding a scattering layer, we were able to boost the power conversion efficiency (PCE) to 10.8%, using an organic ruthenium complex. The same implementation was carried out using a natural dye, betalains, extracted from Sicilian prickly pear. In this case, the conversion efficiency doubled from 1 to 2% (measured at 1 SUN illumination, 100 mW/cm2 under solar simulation irradiation). Moreover, we obtained (measured at 0.1 SUN, 10 mW/cm2 under blue light LED irradiation) a record efficiency of 15% with the betalain-based dye, paving the way for indoor applications in organic natural devices. Finally, an attempt to scale up the system is shown, and a betalain-based- dye-sensitized solar module (DSSM), with an active area of 43.2 cm2 and a PCE of 1.02%, was fabricated for the first time.

Light-Stable Methylammonium-Free Inverted Flexible Perovskite Solar Modules on PET Exceeding 10.5% on a 15.7 cm2 Active Area.

Perovskite solar modules (PSMs) have been attracting the photovoltaic market, owing to low manufacturing costs and process versatility. The employment of flexible substrates gives the chance to explore new applications and further increase the fabrication throughput. However, the present state-of-the-art of flexible perovskite solar modules (FPSMs) does not show any data on light-soaking stability, revealing that the scientific community is still far from the potential marketing of the product. During this work, we demonstrate, for the first time, an outstanding light stability of FPSMs over 1000 h considering the recovering time (T80 = 730 h), exhibiting a power conversion efficiency (PCE) of 10.51% over a 15.7 cm2 active area obtained with scalable processes by exploiting blade deposition of a transporting layer and a stable double-cation perovskite (cesium and formamidinium, CsFA) absorber.

Air-Processed Infrared-Annealed Printed Methylammonium-Free Perovskite Solar Cells and Modules Incorporating Potassium-Doped Graphene Oxide as an Interlayer.

The use of solution processes to fabricate perovskite solar cells (PSCs) represents a winning strategy to reduce capital expenditure, increase the throughput, and allow for process flexibility needed to adapt PVs to new applications. However, the typical fabrication process for PSC development to date is performed in an inert atmosphere (nitrogen), usually in a glovebox, hampering the industrial scale-up. In this work, we demonstrate, for the first time, the use of double-cation perovskite (forsaking the unstable methylammonium (MA) cation) processed in ambient air by employing potassium-doped graphene oxide (GO-K) as an interlayer, between the mesoporous TiO2 and the perovskite layer and using infrared annealing (IRA). We upscaled the device active area from 0.09 to 16 cm2 by blade coating the perovskite layer, exhibiting power conversion efficiencies (PCEs) of 18.3 and 16.10% for 0.1 and 16 cm2 active area devices, respectively. We demonstrated how the efficiency and stability of MA-free-based perovskite deposition in air have been improved by employing GO-K and IRA.

Easy Strategy to Enhance Thermal Stability of Planar PSCs by Perovskite Defect Passivation and Low-Temperature Carbon-Based Electrode.

Organic-inorganic lead halide perovskite has recently emerged as an efficient absorber material for solution process photovoltaic (PV) technology, with certified efficiency exceeding 25%. The development of low-temperature (LT) processing is a challenging topic for decreasing the energy payback time of perovskite solar cell (PSC) technology. In this context, the LT planar n-i-p architecture meets all the requirements in terms of efficiency, scalability, and processability. However, the long-term stability of the LT planar PSC under heat and moisture stress conditions has not been carefully assessed. Here, a detailed study on thermal and moisture stability of large-area (1 cm2) LT planar PSCs is presented. In particular, the key role in thermal stability of potassium iodide (KI) insertion in the perovskite composition is demonstrated. It is found that defect passivation of triple-cation perovskite by KI doping inhibits the halide migration induced by thermal stress at 85 °C and delays the formation of degradation subproducts. T80, defined as the time when the cell retains 80% of initial efficiency, is evaluated both for reference undoped devices and KI-doped ones. The results show that T80 increases 3 times when KI doping is used. Moreover, an HTL-free architecture where the Au top electrode is replaced with low-T screen-printable carbon paste is proposed. The combination of the carbon-based HTL-free architecture and KI-doped perovskite permits T80 to increase from 40 to 414 h in unsealed devices.

Rational Design of Photo-Electrochemical Hybrid Devices Based on Graphene and Chlamydomonas reinhardtii Light-Harvesting Proteins.

Dye-sensitized solar cells (DSSCs) have been highlighted as the promising alternative to generate clean energy based on low pay-back time materials. These devices have been designed to mimic solar energy conversion processes from photosynthetic organisms (the most efficient energy transduction phenomenon observed in nature) with the aid of low-cost materials. Recently, light-harvesting complexes (LHC) have been proposed as potential dyes in DSSCs based on their higher light-absorption efficiencies as compared to synthetic dyes. In this work, photo-electrochemical hybrid devices were rationally designed by adding for the first time Leu and Lys tags to heterologously expressed light-harvesting proteins from Chlamydomonas reinhardtii, thus allowing their proper orientation and immobilization on graphene electrodes. The light-harvesting complex 4 from C. reinhardtii (LHC4) was initially expressed in Escherichia coli, purified via affinity chromatography and subsequently immobilized on plasma-treated thin-film graphene electrodes. A photocurrent density of 40.30 ± 9.26 µA/cm2 was measured on devices using liquid electrolytes supplemented with a phosphonated viologen to facilitate charge transfer. Our results suggest that a new family of graphene-based thin-film photovoltaic devices can be manufactured from rationally tagged LHC proteins and opens the possibility to further explore fundamental processes of energy transfer for biological components interfaced with synthetic materials.

Progress, highlights and perspectives on NiO in perovskite photovoltaics.

The power conversion efficiency (PCE) of NiO based perovskite solar cells has recently hit a record 22.1% with a hybrid organic-inorganic perovskite composition and a PCE above 15% in a fully inorganic configuration was achieved. Moreover, NiO processing is a mature technology, with different industrially attractive processes demonstrated in the last few years. These considerations, along with the excellent stabilities reported, clearly point towards NiO as the most efficient inorganic hole selective layer for lead halide perovskite photovoltaics, which is the topic of this review. NiO optoelectronics is discussed by analysing the different doping mechanisms, with a focus on the case of alkaline and transition metal cation dopants. Doping allows tuning the conductivity and the energy levels of NiO, improving the overall performance and adapting the material to a variety of perovskite compositions. Furthermore, we summarise the main investigations on the NiO/perovskite interface stability. In fact, the surface of NiO is commonly oxidised and reactive with perovskite, also under the effect of light, thermal and electrical stress. Interface engineering strategies should be considered aiming at long term stability and the highest efficiency. Finally, we present the main achievements in flexible, fully printed and lead-free perovskite photovoltaics which employ NiO as a layer and provide our perspective to accelerate the improvement of these technologies. Overall, we show that adequately doped and passivated NiO might be an ideal hole selective layer in every possible application of perovskite solar cells.

Fabrication and Morphological Characterization of High-Efficiency Blade-Coated Perovskite Solar Modules.

Organo-metal halide perovskite demonstrates a large potential for achieving highly efficient photovoltaic devices. The scaling-up process represents one of the major challenges to exploit this technology at the industrial level. Here, the scaling-up of perovskite solar modules from 5 × 5 to 10 × 10 cm2 substrate area is reported by blade coating both the CH3NH3PbI3 perovskite and spiro-OMeTAD layers. The sequential deposition approach is used in which both lead iodide (PbI2) deposition and the conversion step are optimized by using additives. The PbI2 solution is modified by adding methylammonium iodide (MAI) which improves perovskite crystallinity and pore filling of the mesoporous TiO2 scaffold. Optimization of the conversion step is achieved by adding a small concentration of water into the MAI-based solution, producing large cubic CH3NH3PbI3 grains. The combination of the two modifications leads to a power conversion efficiency of 14.7% on a perovskite solar module with an active area of 47 cm2.

Perovskite-Polymer Blends Influencing Microstructures, Nonradiative Recombination Pathways, and Photovoltaic Performance of Perovskite Solar Cells.

Solar cells based on organic-inorganic halide perovskites are now leading the photovoltaic technologies because of their high power conversion efficiency. Recently, there have been debates on the microstructure-related defects in metal halide perovskites (grain size, grain boundaries, etc.) and a widespread view is that large grains are a prerequisite to suppress nonradiative recombination and improve photovoltaic performance, although opinions against it also exist. Herein, we employ blends of methylammonium lead iodide perovskites with an insulating polymer (polyvinylpyrrolidone) that offer the possibility to tune the grain size in order to obtain a fundamental understanding of the photoresponse at the microscopic level. We provide, for the first time, spatially resolved details of the microstructures in such blend systems via Raman mapping, light beam-induced current imaging, and conductive atomic force microscopy. Although the polymer blend systems systematically alter the morphology by creating small grains (more grain boundaries), they reduce nonradiative recombination within the film and enhance its spatial homogeneity of radiative recombination. We attribute this to a reduction in the density of bulk trap states, as evidenced by an order of magnitude higher photoluminescence intensity and a significantly higher open-circuit voltage when the polymer is incorporated into the perovskite films. The solar cells employing blend systems also show nearly hysteresis-free power conversion efficiency ∼17.5%, as well as a remarkable shelf-life stability over 100 days.

Anthocyanic pigments from elicited in vitro grown shoot cultures of Vaccinium corymbosum L., cv. Brigitta Blue, as photosensitizer in natural dye-sensitized solar cells (NDSSC).

We investigated the effect on anthocyanins and total phenols content and antioxidant capacity of in vitro shoot cultures of Vaccinium corymbosum L., cv. Brigitta Blue, grown on an eliciting medium supplied with 10 µM naphthalene acetic acid, in combination with reduced content of salts and organics in respect to the basal medium. After 45 days, higher content of total phenols and anthocyanins was obtained from extracts of shoots grown on the elicitation medium. Anthocyanin molecules, absent in control shoots, were identified by HPLC-MS as delphinidine-glycoside, cyanidine-glycoside, delphinidine-arabinoside, cyanidine- arabinoside and cyanidine-acetylglycoside. Chlorogenic acid, present in control shoots, was nearly absent in elicited shoots. We exploited the anthocyanin - based raw extracts of "Brigitta Blue" shoots grown on the elicitation medium as a source of natural dye photosensitizers for Dye Sensitized Solar Cells, taking into account that such raw extracts showed antioxidant properties and photostability features. A purified dye was also prepared and the comparison of the latter with the raw one has been analysed by spectrophotometric, chromatographic and power conversion efficiency determination. The power conversion efficiencies from the raw and the purified dye were not different and they were comparable to the data obtained by other authors with anthocyanin-based dyes from in vivo grown plants.

High-Efficiency Perovskite Solar Cell Based on Poly(3-Hexylthiophene): Influence of Molecular Weight and Mesoscopic Scaffold Layer.

Here, we investigated the effect of the molecular weight (MW) of poly 3-hexylthiophene (P3HT) hole-transport material on the performance of perovskite solar cells (PSCs). We found that by increasing the MW the photovoltaic performances of the cells are enhanced leading to an improvement of the overall efficiency. P3HT-based PSCs with a MW of 124 kDa can achieve an overall average efficiency of 16.2 %, double with respect to the ones with a MW of 44 kDa. Opposite to spiro-OMeTAD-based PSCs, the photovoltaic parameters of the P3HT-based devices are enhanced by increasing the mesoporous TiO2 layer thickness from 250 to 500 nm. Moreover, for a titania scaffold layer thickness of 500 nm, the efficiency of P3HT-based PSCs with high MW is larger than the spiro-OMeTAD based PSCs with the same scaffold layer thickness. Recombination reactions of the devices were also investigated by voltage decay and electrochemical impedance spectroscopy. We found that the relationship between P3HT MW and cell performance is related to the reduction of charge recombination and to the increase of the P3HT light absorption by increasing the MW.