Particle Size, Dose, and Confinement Affect Passive Diffusion Flux through the Membrane Concentration Boundary Layer.

The authors present a steady-state-, particle-size-, and dose-dependent dissolution-permeation model that describes particle dissolution within the concentration boundary layer (CBL) adjacent to a semipermeable surface. It is critical to understand how particle size and dose affect the behavior of dissolving particles in the presence of a CBL adjacent to a semipermeable surface both in vivo and in vitro. Control of particle size is ubiquitous in the pharmaceutical industry; however, traditional pharmaceutical assumptions of particle dissolution typically ignore particle dissolution within the length scale of the CBL. The CBL does not physically prevent particles from traveling to the semipermeable surface (mucus, epithelial barrier, synthetic membrane, etc.), and particle dissolution can occur within the CBL thickness (δC) if the particle is sufficiently small (∼dparticle ≤ δC). The total flux (the time rate transport of molecules across the membrane surface per unit area) was chosen as a surrogate parameter for measuring the additional mass generated by particles dissolving within the donor CBL. Mass transfer experiments aimed to measure the total flux of drug using an ultrathin large-area membrane diffusion cell described by Sinko et al. with a silicone-based membrane ( Mol. Pharmaceutics 2020, 17, (7) 2319-2328, DOI: 10.1021/acs.molpharmaceut.0c00040). Suspensions of ibuprofen, a model weak-acid drug, with three different particle-size distributions with average particle diameters of 6.6, 37.4, and 240 µm at multiple doses corresponding to a range of suspension concentrations with dimensionless dose numbers of 2.94, 14.7, 147, and 588 were used to test the model. Experimentally measured total flux across the semipermeable membrane/CBL region agreed with the predictions from the proposed model, and at a range of relatively low suspension concentrations, dependent on the average particle size, there was a measurable effect on the flux due to the difference in δC that formed at the membrane surface. Additionally, the dose-dependent total flux across the membrane was up to 10% higher than the flux predicted by the standard Higuchi-Hiestand dissolution model where the effects of confinement were ignored as described by Wang et al. ( Mol. Pharmaceutics 2012, 9 (5), 1052-1066, DOI: 10.1021/mp2002818).

Ultrathin, Large-Area Membrane Diffusion Cell for pH-Dependent Simultaneous Dissolution and Absorption Studies.

Preclinical evaluation of modern oral dosage forms requires more advanced in vitro devices as the trend of selecting low solubility, high permeability compounds for commercial development continues. Current dissolution methodologies may not always be suitable for such compounds due to excessive fluid volume, high fluid shear rates, heterogeneity of shear rates, suboptimal fluid flow, and, ultimately, the lack of absorption ability (Gray The Science of USP 1 and 2 Dissolution: Present Challenges and Future Relevance; Pharmaceutical Research, 2009; Vol. 26; pp 1289-1302). Herein, a new dissolution apparatus is introduced in combination with an ultrathin, semipermeable polymer membrane that mimics human passive absorption for lipophilic compounds. The ultrathin large-area polydimethylsiloxane (PDMS) membrane (UTLAM) absorption system is designed to mimic the dissolution and passive transcellular diffusion process representing the oral absorption pathway. A simple spin-casting method was developed to fabricate the ultrathin highly uniform membranes. To minimize membrane resistance to diffusion and maximize transport across the polymer membrane, 10-40 µm PDMS membranes were successfully prepared. A new diffusion cell was designed and tested to support the UTLAM and incorporates a hydrofoil impeller for more desirable hydrodynamics and mixing, using ibuprofen as a model weak acidic drug. UTLAM permeability was sufficiently high that the aqueous boundary layer contributed to the overall permeability of the system. This diffusion cell system demonstrated that, when the aqueous diffusion layer contributes to the overall resistance to transport, the pH at which absorption is 50% of maximum (pH50%) shifts from the pKa to higher values, demonstrating why weak acid drugs can exhibit high absorption at pH's significantly greater than their pKa. High rates of transport across the UTLAM are possible for drugs with high partition coefficients (i.e., BCS II compounds even under mostly ionized conditions), and PDMS UTLAMs may be tailored to simulate human intestinal passive absorption rates.