Light, Copper, Action: Visible-Light Illumination Enhances Bactericidal Activity of Copper Particles.

Bacteria are an old concern to human health, as they are responsible for nosocomial infections, and the number of antibiotic-resistant microorganisms keeps growing. Copper is known for its intrinsic biocidal properties, and therefore, it is a promising material to combat infections when added to surfaces. However, its biocidal properties in the presence of light illumination have not been fully explored, especially regarding the use of microsized particles since nanoparticles have taken over all fields of research and subjugated microparticles despite them being abundant and less expensive. Thus, the present work studied the bactericidal properties of metallic copper particles, in microscale (CuMPs) and nanoscale (CuNPs), in the absence of light and under white LED light illumination. The minimum bactericidal concentration (MBC) of CuMPs against Staphylococcus aureus that achieved a 6-log reduction was 5.0 and 2.5 mg mL-1 for assays conducted in the absence of light and under light illumination, respectively. Similar behavior was observed against Escherichia coli. The bactericidal activity under illumination provided a percentage increase in log reduction values of 65.2% for S. aureus and 166.7% for E. coli when compared to the assays under dark. This assay reproduced the testing CuNPs, which showed superior bactericidal activity since the concentration of 2.5 mg mL-1 promoted a 6-log reduction of both bacteria even under dark. Its superior bactericidal activity, which overcame the effect of illumination, was expected once the nanoscale facilitated the interaction of copper within the surface of bacteria. The results from MBC were supported by fluorescence microscopy and atomic absorption spectroscopy. Therefore, CuMPs and CuNPs proved to have size- and dose-dependent biocidal activity. However, we have shown that CuMPs photoactivity is competitive compared to that of CuNPs, allowing their application as a self-cleaning material for disinfection processes assisted by conventional light sources without additives to contain the spread of pathogens.

Phototribology: Control of Friction by Light.

In dry sliding, the coefficient of friction depends on the material pair and contact conditions. If the material and operating conditions remain unchanged, the coefficient of friction is constant. Obviously, we can tune friction by surface treatments, but it is a nonreversible process. Here, we report active control of friction forces on TiO2 thin films under UV light. It is reversible and stable and can be tuned/controlled with the light wavelength. The analysis of atomic force microscopy signals by wavelet spectrograms reveals different mechanisms acting in the darkness and under UV. Ab initio simulations on UV light-exposed TiO2 show a lower atomic orbital overlapping on the surface, which leads to a friction reduction of up to 60%. We suggest that photocontrol of friction is due to the modification of atomic orbital interactions from both surfaces at the sliding interface.

On the physicochemical origin of nanoscale friction: the polarizability and electronegativity relationship tailoring nanotribology.

Friction is a ubiquitous manifestation of nature, and when it is studied at the nanoscale, complex and interesting effects arise from fundamental physical and chemical surface properties. Surprisingly, and probably due to the complexity of nanofriction studies, this aspect has not been completely discussed in prior studies. To fully consider the physicochemical influence in nanoscale friction, amorphous carbon films with different amounts of hydrogen and fluorine were prepared, chemically characterized, and evaluated via lateral force microscopy. Hydrogen and fluorine were selected because although they exhibit different physicochemical properties, both contribute to frictional force reduction. Indeed, to explain the experimental behavior, it is necessary to propose a new damping constant unifying both polarizability (physical) and electronegativity (chemical) properties. The satisfactory agreement between theory and experiments may encourage and enhance deeper discussion and new experiments that take into account the chemical peculiarities of frictional behavior relating to nanoscale elastic regimes.

Substrate Bias Voltage Tailoring the Interfacial Chemistry of a-SiC x:H: A Surprising Improvement in Adhesion of a-C:H Thin Films Deposited on Ferrous Alloys Controlled by Oxygen.

Hydrogenated amorphous carbon thin films (a-C:H) have attracted much attention because of their surprising properties, including ultralow friction coefficients in specific conditions. Adhesion of a-C:H films on ferrous alloys is poor due to chemical and physical aspects, avoiding a widespread application of such a film. One possibility to overcome this drawback is depositing an interlayer-an intermediate thin film-between the carbon-based coating and the substrate to improve chemical interaction and adhesion. Based on this, interlayers play a key role on a-C:H thin-film adhesion through a better chemical network structure at the outermost layer of the a-SiC x:H interlayer, i.e., the a-C:H/a-SiC x:H interface. However, despite the latest important advances on the subject, the coating adhesion continues being a cumbersome problem since it depends on multifactorial causes. Thus, the purpose of this paper is to report a standard protocol leading to surprising good results based on the control of the interfacial chemical bonding by properly biasing the substrate (between 500 and 800 V) during the a-SiC x:H interlayer deposition at an appropriate low temperature, by using hexamethyldisiloxane as precursor. The interlayers and the outermost interfaces were analyzed by a comprehensive set of techniques, including X-ray photoelectron spectroscopy, glow discharge optical emission spectroscopy, and Fourier transform infrared spectroscopy. Nanoscratch tests, complemented by scanning electron microscopy and energy-dispersive X-ray spectroscopy, were used to evaluate the critical load for delamination to certify and quantify the adhesion improvement. This study was important to identify the chemical local bonding of the elements at the interface and its local environment, including the in-depth chemical composition profile of the coating. An important effect is that the oxygen content decreases on increasing substrate bias voltage, improving the adhesion of the film. This is due to the fact that energetic ion hitting the growing interlayer breaks Si-O and C-O bonds, augmenting the content of Si-C and C-C bonds at the outermost interface of the a-SiC x:H interlayer and enhancing the a-C:H coating adhesion. Moreover, the combination of high bias voltage (800 V) and low temperature (150 °C) during the a-SiC x:H interlayer deposition allows good adhesion of a-C:H thin films due to sputtering of light elements like oxygen. Therefore, an appropriated bias and temperature combination can open new pathways in a-C:H thin-film deposition at low temperatures. These results are particularly interesting for temperature-sensible metal alloys, where well-adhered a-C:H thin films are mandatory for tribological applications.

Towards superlubricity in nanostructured surfaces: the role of van der Waals forces.

Hydrogenated amorphous carbon (a-C:H) thin films have a unique combination of properties that are fundamental in mechanical and electromechanical devices aimed at energy efficiency issues. The literature brings a wealth of information about the ultra-low friction (superlubricity) mechanism in a-C:H thin films. However, there is persistent controversy concerning the physicochemical mechanisms of contact mechanics at the atomic/molecular level and the role of electrical interactions at the sliding interface is still a matter of debate. We find that the hydrogenation of the outermost nanostructured surface atomic layers of a-C:H thin films is proportional to the surface potential and also to the friction forces arising at the sliding interface. A higher hydrogen-to-carbon ratio reduces the surface potential, directly affecting frictional forces by a less effective long-term interaction. The structural ultra-low friction (superlubricity) is attributed to a lower polarizability at the outermost nanostructured layer of a-C:H thin films due to a higher hydrogen density, which renders weaker van der Waals forces, in particular London dispersion forces. More hydrogenated nanodomains at the surface of a-C:H thin films are proposed to be used to tailor superlubricity.

Superomniphobic and easily repairable coatings on copper substrates based on simple immersion or spray processes.

Textures that resemble typical fern or bracken plant species (dendrite structures) were fabricated for liquid repellency by dipping copper substrates in a single-step process in solutions containing AgNO3 or by a simple spray liquid application. Superhydrophobic surfaces were produced using a solution containing AgNO3 and trimethoxypropylsilane (TMPSi), and superomniphobic surfaces were produced by a two-step procedure, immersing the copper substrate in a AgNO3 solution and, after that, in a solution containing 1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES). The simple functionalization processes can also be used when the superomniphobic surfaces were destroyed by mechanical stress. By immersion of the wrecked surfaces in the above solutions or by the spray method and soft heating, the copper substrates could be easily repaired, regenerating the surfaces' superrepellency to liquids. The micro- and nanoroughness structures generated on copper surfaces by the deposition of silver dendrites functionalized with TMPSi presented apparent contact angles greater than 150° with a contact angle hysteresis lower than 10° when water was used as the test liquid. To avoid total wettability with very low surface tension liquids, such as rapeseed oil and hexadecane, a thin perfluorinated coating of poly(tetrafluoroethylene) (PTFE), produced by physical vapor deposition, was used. A more efficient perfluorinated coating was obtained when PFDTES was used. The superomniphobic surfaces produced apparent contact angles above 150° with all of the tested liquids, including hexadecane, although the contact angle hysteresis with this liquid was above 10°. The coupling of dendritic structures with TMPSi/PTFE or directly by PFDTES coatings was responsible for the superrepellency of the as-prepared surfaces. These simple, fast, and reliable procedures allow the large area, and cost-effective scale fabrication of superrepellent surfaces on copper substrates for various industrial applications with the advantage of easy recovery of the surface repellency after damage.

Multi-scale structured, superhydrophobic and wide-angle, antireflective coating in the near-infrared region.

Superhydrophobic self-cleaning surfaces were produced with simultaneous wide-angle optical transmittance in the near-infrared region and antireflection properties from combination of multi-scale surface topology based on silica nanoparticles, index grading and interference.

Micro and nano-texturization of intermetallic oxide alloys by a single anodization step: preparation of artificial self-cleaning surfaces.

Micro- and nanostructures of Ti-γCu (γ = 0, 30, 50, 70, and 100 wt %) intermetallic alloys were produced through a single anodization step. It was found that the original alloy composition influences the final oxide morphology obtained after anodization which presented formation of a microstructure with nanotubes, nanoparticles or nanopillars on the surface. Pure Ti and Cu oxide metals and their alloys presented hydrophilic or superhydrophilic properties immediately after anodization. When the anodized pure metal and/or Ti-γCu surfaces were functionalized with trimethoxypropylsilane (TPMSi), by dipping and coating with a thin perfluorinated layer, the treated substrates became in all cases superhydrophobic (water contact angles in the range of 152-166°), showing excellent self-cleaning properties with hysteresis below 3°. These results can be explained by a combination of nanomicro morphologies with low surface energy compounds in the topmost monolayers. The decrease in hysteresis was associated with a higher M-OH bond concentration on the anodized surfaces, which allowed for more complete TMPSi coating coverage. This study also indicates that easy and effective fabrication of superhydrophobic surfaces in pure metals and alloys is possible without involving traditional multistep processes.

Analysis of dip coating processing parameters by double optical monitoring.

Double optical monitoring is applied to determine the influence of main process parameters on the formation of sulfated zirconia and self-assembled mesoporous silica solgel films by dip coating. In addition, we analyze, for the first time to the best of our knowledge, the influence of withdrawal speed, temperature, and relative humidity on refractive-index and physical thickness variations (uncertainties of +/-0.005 and +/-7 nm) during the process. Results provide insight into controlled production of single and multilayer films from complex fluids by dip coating.

Double optical monitoring of dip coating with a time-varying refractive index.

A brief overview of optical monitoring for vacuum and wet-bench film-deposition processes is presented. Interferometric and polarimetric measurements are combined with regard to simultaneous monitoring of refractive index and physical thickness in real time. Monitoring stability and accuracy are verified during dip coating with a transparent oil standard. This double optical technique is applied to dip coating with a multicomponent zirconyl chloride aqueous solution, whose resulting temporal refractive-index and physical-thickness curves indicate good reproducibility as well as significant sensitivity to changes of film-flow properties during the dip-coating process.

Optically monitored dip coating as a contactless viscometry method for liquid films.

Real-time interferometric monitoring of the dip coating process is applied to the study of properties of flowing liquids. Nonvolatile Newtonian oils are considered, allowing validity of a simple model after the steady state is reached where film physical thickness depends on time as t(-1/2). Measurement of two distinct mineral oil standards, under several withdrawing speeds, resulted in kinematic viscosities of 1.17+/-0.03 and 9.9+/-0.2 S (1S = 1 cm2/s). Agreement of these results with nominal values from the manufacturer suggests that interferometric monitoring of dip coating may become a valuable method for accurate, contactless viscometry of liquid films. Advantages and present limitations are discussed.

Interferometric monitoring of dip coating.

Dip-coated films, which are widely used in the coating industry, are usually measured by capacitive methods with micrometric precision. For the first time to our knowledge, we have applied an interferometric determination of the evolution of thickness in real time to nonvolatile Newtonian mineral oils with several viscosities and distinct dip withdrawing speeds. The evolution of film thickness during the process depends on time as t(-1/2), in accordance with a simple model. Comparison with measured results with an uncertainty of +/- 0.007 microm) showed good agreement after the initial steps of the process had been completed.