Oxidative stress and inflammation response after nanoparticle exposure: differences between human lung cell monocultures and an advanced three-dimensional model of the human epithelial airways.

Combustion-derived and manufactured nanoparticles (NPs) are known to provoke oxidative stress and inflammatory responses in human lung cells; therefore, they play an important role during the development of adverse health effects. As the lungs are composed of more than 40 different cell types, it is of particular interest to perform toxicological studies with co-cultures systems, rather than with monocultures of only one cell type, to gain a better understanding of complex cellular reactions upon exposure to toxic substances. Monocultures of A549 human epithelial lung cells, human monocyte-derived macrophages and monocyte-derived dendritic cells (MDDCs) as well as triple cell co-cultures consisting of all three cell types were exposed to combustion-derived NPs (diesel exhaust particles) and to manufactured NPs (titanium dioxide and single-walled carbon nanotubes). The penetration of particles into cells was analysed by transmission electron microscopy. The amount of intracellular reactive oxygen species (ROS), the total antioxidant capacity (TAC) and the production of tumour necrosis factor (TNF)-alpha and interleukin (IL)-8 were quantified. The results of the monocultures were summed with an adjustment for the number of each single cell type in the triple cell co-culture. All three particle types were found in all cell and culture types. The production of ROS was induced by all particle types in all cell cultures except in monocultures of MDDCs. The TAC and the (pro-)inflammatory reactions were not statistically significantly increased by particle exposure in any of the cell cultures. Interestingly, in the triple cell co-cultures, the TAC and IL-8 concentrations were lower and the TNF-alpha concentrations were higher than the expected values calculated from the monocultures. The interplay of different lung cell types seems to substantially modulate the oxidative stress and the inflammatory responses after NP exposure.

Effects of combustion-derived ultrafine particles and manufactured nanoparticles on heart cells in vitro.

Evidence from epidemiological studies indicates that acute exposure to airborne pollutants is associated with an increased risk of morbidity and mortality attributed to cardiovascular diseases. The present study investigated the effects of combustion-derived ultrafine particles (diesel exhaust particles) as well as engineered nanoparticles (titanium dioxide and single-walled carbon nanotubes) on impulse conduction characteristics, myofibrillar structure and the formation of reactive oxygen species in patterned growth strands of neonatal rat ventricular cardiomyocytes in vitro. Diesel exhaust particles as well as titanium dioxide nanoparticles showed the most pronounced effects. We observed a dose-dependent change in heart cell function, an increase in reactive oxygen species and, for titanium dioxide, we also found a less organized myofibrillar structure. The mildest effects were observed for single-walled carbon nanotubes, for which no clear dose-dependent alterations of theta and dV/dt(max) could be determined. In addition, there was no increase in oxidative stress and no change in the myofibrillar structure. These results suggest that diesel exhaust as well as titanium dioxide particles and to a lesser extent also single-walled carbon nanotubes can directly induce cardiac cell damage and can affect the function of the cells.

Identification of the mass spectral signature of organic aerosols from wood burning emissions.

Throughout the winter months, the village of Roveredo, Switzerland, frequently experiences strong temperature inversions that contribute to elevated levels of particulate matter. Wood is used as fuel for 75% of the domestic heating installations in Roveredo, which makes it a suitable location to study wood burning emissions in the atmosphere in winter. An Aerodyne quadrupole aerosol mass spectrometer (Q-AMS) was used to characterize the composition of the submicrometer, non-refractory aerosol particles at this location during two field campaigns in March and December 2005. Wood burning was found to be a major source of aerosols at this location in winter. Organics dominated the composition of the aerosols from this source, contributing up to 85% of the total AMS measured mass during the afternoon and evening hours. Carbonaceous particle analysis showed that organic carbon composed up to 86% of the total carbon mass collected at evening times. Results from 14C isotope determination revealed that up to 94% of the organic mass came from non-fossil sources, which can be attributed mostlyto wood burning. The unique combination of off-line 14C isotope analysis and on-line aerosol mass spectrometry was used to identify periods during which organic mass was mainly from wood burning emissions and allowed for the identification of the AMS spectral signature of this source in the atmosphere. The identified ambient signature of wood burning was found to be very similar to the mass spectral signature obtained during the burning of chestnut wood samples in a small stove and also to the spectrum of levoglucosan. Particles from wood burning appeared to be composed of highly oxygenated organic compounds, and mass fragments 60, 73, and 137 have been suggested as marker fragments for wood burning aerosols. Mass fragment 44, which is used as a marker for oxygenated organic aerosols (OOA), contributed about 5% to the total organic signal from primary wood burning sources. The ratio of the organic mass emitted from wood burning to m/z 60 in Roveredo is 36. This ratio may be used to provide an estimate of the organic aerosol mass emitted from wood burning in other locations.

Particle emissions from diesel passenger cars equipped with a particle trap in comparison to other technologies.

Tail pipe particle emissions of passenger cars, with different engine and aftertreatment technologies, were determined with special focus on diesel engines equipped with a particle filter. The particle number measurements were performed, during transient tests, using a condensation particle counter. The measurement procedure complied with the draft Swiss ordinance, which is based on the findings of the UN/ECE particulate measurement program. In addition, particle mass emissions were measured by the legislated and a modified filter method. The results demonstrate the high efficiency of diesel particle filters (DPFs) in curtailing nonvolatile particle emissions over the entire size range. Higher emissions were observed during short periods of DPF regeneration and immediately afterward, when a soot cake has not yet formed on the filter surface. The gasoline vehicles exhibited higher emissions than the DPF equipped diesel vehicles but with a large variation depending on the technology and driving conditions. Although particle measurements were carried out during DPF regeneration, it was impossible to quantify their contribution to the overall emissions, due to the wide variation in intensity and frequency of regeneration. The numbers counting method demonstrated its clear superiority in sensitivity to the mass measurement. The results strongly suggest the application of the particle number counting to quantify future low tailpipe emissions.

Comparison of mass-based and non-mass-based particle measurement systems for ultra-low emissions from automotive sources.

Drastic reduction in particle emissions of diesel-powered vehicles and new findings on the health impact of particles raise the question of a more sensitive measurement procedure. In this paper, 16 different particle mass measurement systems are compared on a diesel heavy-duty engine equipped with a particle filter to investigate their feasibility for particle characterization for future ultra-low concentration levels. The group of instruments comprises mass-related methods (filter methods, laser-induced incandescence, photoacoustic detection, photoelectric charging, combined inertial and mobility sizing, opacity) as well as non-mass-related methods (CPC, diffusion battery, diffusion charger, ELPI, light scattering). The instruments are compared on the basis of repeatability, limit of detection, sensitivity, time resolution and correlation with the regulated gravimetric filter method, and elemental carbon fraction (EC). Several time-resolved methods show good performance and give reliable results. Opacimeters and light scattering, however, reveal shortcomings at these low concentrations. For all time-resolved advanced methods, poor correlation with the regulated filter method is observed, but most of them show good correlation with the EC fraction of the particles. This outcome demonstrates the crucial role of the sampling conditions for measurement methods that do not exclude volatile material from detection. A clear improvement in sensitivity is observed when non-mass-based instruments are applied (e.g., number or surface-related methods). The results reveal that reliable measurement methods exist for future measurement procedures. However, a change in the measurement method will lead to a discontinuity in the inventories, making it difficult to compare the particle emissions from future and past vehicle generations.

Influence of diesel engine combustion parameters on primary soot particle diameter.

Effects of engine operating parameters and fuel composition on both primary soot particle diameter and particle number size distribution in the exhaust of a direct-injected heavy-duty diesel engine were studied in detail. An electrostatic sampler was developed to deposit particles directly on transmission electron microscopy (TEM) grids. Using TEM, the projected area equivalent diameter of primary soot particles was determined. A scanning mobility particle sizer (SMPS) was used for the measurement of the particle number size distribution. Variations in the main engine operating parameters (fuel injection system, air management, and fuel properties) were made to investigate soot formation and oxidation processes. Primary soot particle diameters determined by TEM measurements ranged from 17.5 to 32.5 nm for the diesel fuel and from 24.1 to 27.2 nm for the water-diesel emulsion fuel depending on the engine settings. For constant fuel energy flow rate, the primary particle size from the water-diesel emulsion fuel was slightly larger than that from the diesel fuel. A reduction in primary soot particle diameter was registered when increasing the fuel injection pressure (IP) or advancing the start of injection (SOI). Larger primary soot particle diameters were measured while the engine was operating with exhaust gas recirculation (EGR). Heat release rate analysis of the combustion process revealed that the primary soot particle diameter decreased when the maximum flame temperature increased for the diesel fuel.