Triiodide Attacks the Organic Cation in Hybrid Lead Halide Perovskites: Mechanism and Suppression.

Molecular I2 can be produced from iodide-based lead perovskites under thermal stress; triiodide, I3 - , is formed from this I2 and I- . Triiodide attacks protic cation MA+ - or FA+ -based lead halide perovskites (MA+ , methylammonium; FA+ , formamidinium) as explicated through solution-based nuclear magnetic resonance (NMR) studies: triiodide has strong hydrogen-bonding affinity for MA+ or FA+ , which leads to their deprotonation and perovskite decomposition. Triiodide is a catalyst for this decomposition that can be obviated through perovskite surface treatment with thiol reducing agents. In contrast to methods using thiol incorporation into perovskite precursor solutions, no penetration of the thiol into the bulk perovskite is observed, yet its surface application stabilizes the perovskite against triiodide-mediated thermal stress. Thiol applied to the interface between FAPbI3 and Spiro-OMeTAD ("Spiro") prevents oxidized iodine species penetration into Spiro and thus preserves its hole-transport efficacy. Surface-applied thiol affects the perovskite work function; it ameliorates hole injection into the Spiro overlayer, thus improving device performance. It helps to increase interfacial adhesion ("wetting"): fewer voids are observed at the Spiro/perovskite interface if thiols are applied. Perovskite solar cells (PSCs) incorporating interfacial thiol treatment maintain over 80% of their initial power conversion efficiency (PCE) after 300 h of 85 °C thermal stress.

Quantitative Hole Mobility Simulation and Validation in Substituted Acenes.

Knowledge of the full phonon spectrum is essential to accurately calculate the dynamic disorder (σ) and hole mobility (µh) in organic semiconductors (OSCs). However, most vibrational spectroscopy techniques under-measure the phonons, thus limiting the phonon validation. Here, we measure and model the full phonon spectrum using multiple spectroscopic techniques and predict µh using σ from only the Γ-point and the full Brillouin zone (FBZ). We find that only inelastic neutron scattering (INS) provides validation of all phonon modes, and that σ in a set of small molecule semiconductors can be miscalculated by up to 28% when comparing Γ-point against FBZ calculations. A subsequent mode analysis shows that many modes contribute to σ and that no single mode dominates. Our results demonstrate the importance of a thoroughly validated phonon calculation, and a need to develop design rules considering the full spectrum of phonon modes.

Anion Exchange Doping: Tuning Equilibrium to Increase Doping Efficiency in Semiconducting Polymers.

High electron affinity (EA) molecules p-type dope low ionization energy (IE) polymers, resulting in an equilibrium doping level based on the energetic driving force (IE-EA), reorganization energy, and dopant concentration. Anion exchange doping (AED) is a process whereby the dopant anion is exchanged with a stable ion from an electrolyte. We show that the AED level can be predicted using an isotherm equilibrium model. The exchange of the dopant anion (FeCl3-) for a bis(trifluoromethanesulfonamide) (TFSI-) anion in the polymers poly(3-hexylthiophene-2,5-diyl) (P3HT) and poly[3-(2,2-bithien-5-yl)-2,5-bis(2-hexyldecyl)-2,5-dihydropyrrolo[3,4-c]pyrrole-1,4-dione-6,5-diyl] (PDPP-2T) highlights two cases in which the process is nonspontaneous and spontaneous, respectively. For P3HT, FeCl3 provides a high doping level but an unstable counterion, so exchange results in an air stable counterion with a marginal increase in doping. For PDPP-2T, FeCl3 is a weak dopant, but the exchange of FeCl3- for TFSI- is spontaneous, so the doping level increases by >10× with AED.