Increasing the Apical Sizes of Root Enlarged for Root Canal Obturation Influences the Outcome of Single-Root-Canal Teeth Affected by Apical Periodontitis.

OBJECTIVE: To investigate the effect of increasing the apical size of roots enlarged for root canal obturation on the outcome of non-surgical endodontic treatment for teeth with apical periodontitis. METHODS: In this retrospective study, we included 210 cases of single-rooted canals treated at our dental units between October 2009 and January 2022. The clinical outcomes of teeth with enlarged root apical size from the International Organization for Standardization standard numbers 25 to 100 were investigated. RESULTS: The number of teeth with a root apical size of ≤50 and ≥ 55 were 158 and 52, respectively. In the former case, 144 (68.6%) teeth had good prognoses and 14 (6.7%) had poor prognoses. In the latter case, 28 (13.3%) teeth had good prognoses and 24 (11.4%) had poor prognoses. CONCLUSION: Unfavourable clinical outcomes were observed in root canal-filled teeth with an enlarged apical root size of ≥ 55. Thus, these sizes potentially indicate poor outcomes of nonsurgical endodontic treatments.

Rare root canal morphology of maxillary second molars: A report of three cases.

Key Clinical Message: Endodontists should be aware that some maxillary second molars can have more than three roots. If any unusual anatomical features are detected during dental radiography or endodontic procedures, it is necessary to conduct cone-beam computed tomography (CBCT) scanning to prevent procedural mishaps. Abstract: CBCT can provide three-dimensional reconstructed images of the root canal system. With the help of CBCT, variations in tooth root number and root canal morphology, such as extra canals, apical ramifications, apical deltas, and lateral canals, can be identified. Knowledge of the variations is very important for the success of endodontic treatment. This report suggests that endodontists must not assume that a MSM has only three tooth roots, which is the most prevalent number.

Oxidative stress impairs the calcification ability of human dental pulp cells.

BACKGROUND: The relationship between internal root resorption and oxidative stress has not yet been reported. This study aimed to add molecular insight into internal root resorption. The present study was conducted to investigate the effect of hydrogen peroxide (H2O2) as an inducer of oxidative stress on the calcification ability of human dental pulp cells (hDPCs) and the involvement of inositol 1, 4, 5-trisphosphate (IP3). MATERIAL AND METHODS: hDPCs (Lonza, Basel, Switzerland) were exposed to H2O2. Cell viability and reactive oxygen species (ROS) production were then evaluated. To investigate the effect of H2O2 on the calcification ability of hDPCs, real-time PCR for alkaline phosphatase (ALP) mRNA expression, ALP staining, and Alizarin red staining were performed. Data were compared with those of hDPCs pretreated with 2-aminoethyldiphenylborate (2-APB), which is an IP3 receptor inhibitor. RESULTS: H2O2 at concentrations above 250 µM significantly reduced cell viability (P < 0.01). More ROS production occurred in 100 µM H2O2-treated hDPCs than in control cells (P < 0.01). 2-APB significantly decreased the production (P < 0.05). H2O2-treated hDPCs showed significant reductions in ALP mRNA expression (P < 0.01), ALP activity (P < 0.01), and mineralized nodule deposition compared with negative control cells (P < 0.01). 2-APB significantly inhibited these reductions (P < 0.01, P < 0.05 and P < 0.01, respectively). Data are representative of three independent experiments with three replicates for each treatment and values are expressed as means ± SD. CONCLUSION: To the best of our knowledge, this is the first study documenting the involvement of IP3 signaling in the calcification ability of human dental pulp cells impaired by H2O2.

Rapid, high-quality microfabrication of thermoset polymer PDMS using laser-induced bubbles.

Bubbles can be formed by focusing a high-power laser in a liquid. Based on this phenomenon, the present study demonstrated a novel technique, referred to as microFabrication using Laser-Induced Bubbles (microFLIB), for the microfabrication of the thermoset polymer polydimethylsiloxane (PDMS). A conventional nanosecond green laser was focused at the interface between uncured PDMS and a metal target and scanned to generate a line of bubbles at the boundary. The hemispherical shapes of these bubbles produced a groove on the rear side of the PDMS substrate following subsequent thermal curing. After the fabrication of such specimens, metal films could be selectively deposited along the grooves by electroless plating. This process allows rapid, high-quality microfluidic fabrication with potential applications to biochips.