Physical properties of experimental light-curing pattern resins based on poly (n-butyl methacrylate) or poly(iso-butyl methacrylate).

Experimental light-curing pattern resins were fabricated to produce pattern resin materials with adequate dimensional stability. The light-curing pattern resins consisted of poly(n-butyl methacrylate) or poly(iso-butyl methacrylate) (PiBMA) polymers and methacrylate monomers. The physical properties, amount of residual ash after burning, Vickers hardness, flexural strength, and volumetric polymerization shrinkage of each material were determined. The data obtained for the prepared resins were compared with those of a commercially available pattern resin, Palavit G (PG). A lower amount of residual ash was observed for some of the prepared resins than for PG. The Vickers hardness and flexural strength values of all experimental resins were lower than those of PG. The volumetric polymerization shrinkage of all the experimental resins based on PiBMA was lower than that of PG. These results suggest that acrylic light-curing resin materials based on PiBMA may be useful for patterning and indexing during soldering.

Radiopaque properties of polyetheretherketone crown at laboratory study.

OBJECTIVES: There have been no reports on the radiopaque properties of new polyetheretherketone (PEEK) crowns for locating crowns during accidental ingestion or aspiration and detection of secondary caries, which is essential information for clinical application. This study aimed to investigate whether the radiopaque properties of PEEK crowns could be used to identify the site of accidental ingestion or aspiration and detect secondary caries. METHODS: Four types of crowns were fabricated: three non-metal crowns (PEEK, hybrid resin, and zirconia) and one full metal cast crown (gold-silver-palladium alloy). Initially, the images for these crowns were compared using intraoral radiography, chest radiography, cone-beam computed tomography (CBCT), and multi-detector computed tomography (MDCT); computed tomography (CT) values were calculated. Subsequently, the images for the crowns placed on the secondary caries model with two artificial cavities were compared using intraoral radiography. RESULTS: The PEEK crowns displayed the lowest radiopaque properties on radiography and very few artifacts were observed on CBCT and MDCT. On the other hand, the CT values of the PEEK crowns were a little lower than those of the hybrid resin crowns and considerably lower than the zirconia and full metal cast crowns. The cavity could be detected in the PEEK crown-placed secondary caries model through intraoral radiography. CONCLUSIONS: This simulated study of radiopaque properties with four types of crowns suggested that a radiographic imaging system can be used to identify the site of accidental ingestion and aspiration of PEEK crowns and to detect secondary caries of the abutment tooth within a PEEK crown.

Clinical report of six-month follow-up after cementing PEEK crown on molars.

We conducted a six-month clinical follow-up on computer-aided design/computer-aided manufacturing-fabricated molar polyetheretherketone PEEK crowns to investigate their therapeutic effect. Only the PEEK crowns were examined as our study focused on short-term clinical evaluation of the new PEEK material. Twenty-three cases of PEEK crowns placed on the molars of 20 subjects (7 males and 13 females, mean age: 60.6 ± 14.2 years) were included in the study. The evaluation items were the condition of the crowns at the time of cementation and after six months, patient satisfaction, masticatory ability, and occlusal force. Mann-Whitney U tests with a significance level of 5% were used to examine the difference in glucose concentration by masticatory ability, occlusal pressure, and occlusal force, with and without PEEK crowns. The occlusion, margin fit, and contact of all 23 cases at the time of cementing were good. Six months after cementation, there was no crown desorption, fracture or crack, and prosthodontics was not needed in the 22 cases (one patient dropped out). No wear of the dental antagonist was observed. Patient satisfaction was generally high. There was no significant difference in masticatory ability between the groups with and without PEEK crowns. The subject's occlusal force was within the normal range. PEEK crowns used on molars can replace metal crowns and hold promise for an appropriate and effective treatment.

Nd:YVO4 laser groove treatment can improve the shear bond strength between dental PEEK and adhesive resin cement with an adhesive system.

The purpose of this study was to investigate the effect of various surface treatments on the shear bond strength between dental polyetheretherketone (PEEK) and adhesive resin cement. Two hundred and forty specimens were randomly classified into four groups: no treatment, sandblasted, sulfuric-acid-etched, and laser-grooved treatment. Each group was classified into two adhesive resin cement subgroups. Surface roughness, water contact angle, shear bond strength, and failure mode were measured; SEM and XPS results were obtained. The data were statistically analyzed using one-way or two-way analysis of variance and Tukey's honest significant difference test (α=0.05). Laser-grooved PEEK surface showed regular grooves and carbonization by thermal degradation; the surface roughness as well as water contact angle of were the highest in all groups. Shear bond strength values were significantly higher in the laser-groove-treated and sulfuric-acid-etched groups. Laser-groove-treated specimens showed cohesive failure. Laser-grooved treatment can improve shear bond strength between PEEK and adhesive resin cement.

Association between masticatory ability and oral functions.

BACKGROUND: Mastication is the process of breaking ingested food with the teeth and mixing it with saliva to form a mass that is easy to swallow. However, few studies have reported on oral functions, such as occlusal force, tongue pressure, and mastication. The purpose of this study was to evaluate the association between masticatory function and oral functions, such as occlusal force and tongue pressure. MATERIAL AND METHODS: In this study, there were 113 patients (41 men and 72 women; mean age, 68.4 ± 11.3 years) who visited dentists at the Hiroshima University Hospital, Hiroshima, Japan between April 2015 and November 2018. Masticatory function of the patients was evaluated using a masticatory ability test system. In addition, occlusal force was measured using a pressure-sensitive film and the maximum tongue pressure was measured with a tongue pressure measuring device according to a conventional method. The relationship of masticatory ability with occlusal force and tongue pressure was examined using multivariate analysis while considering patients' age, gender, and the number of remaining teeth. RESULTS: Masticatory ability was significantly related to occlusal force, maximum tongue pressure, age, body mass index, the number of remaining teeth, and occlusal contact area (p< 0.05). Multiple regression analysis identified that masticatory ability was significantly associated (p< 0.05) with occlusal force and maximum tongue pressure. CONCLUSIONS: Masticatory ability was significantly associated with occlusal force and maximum tongue pressure, indicating that the large muscle mass in the oral cavity is indispensable for improving masticatory function. Key words:Mastication, tongue pressure, occlusion force, oral function.

Association between salivary alpha-amylase and subjective and objective oral parafunctions in community-dwelling elderly individuals.

BACKGROUND/PURPOSE: Stress in the elderly is caused by loss of physical and psychological health. Although there have been many reports on the intraoral environment affecting physical health, few reports exist on stress and the intraoral environment in the elderly. The aim of this study was to investigate the relationship between salivary α-amylase as an index of stress value and the intraoral environment. MATERIALS AND METHODS: Three hundred and nineteen participants were community-dwelling independent individuals over 65 years old. The outcome variable was salivary α-amylase. After measurement, salivary α-amylase was classified into four groups (0 = 0-30, 1 = 31-45, 2 = 46-60, 3 = 61-200). The predictor variables were physical status (which includes age and male body-mass index) and subjective and objective symptoms (which include present teeth, torus palatinus, torus mandibularis, temporomandibular joint noise, bruxism, and dental attrition). These variables were compared among participants using univariate analysis and multiple logistic regression analysis. RESULTS: The participants included 77 men and 242 women, with a mean age of 75.8 ±â€¯5.4 years (65-94 years). Although temporomandibular joint noise and dental attrition were significantly positively correlated with salivary α-amylase, bruxism was significantly negatively correlated with salivary α-amylase (p < 0.05). Stepwise regression analysis revealed a significant relationship between salivary α-amylase and temporomandibular joint noise, bruxism, and dental attrition. CONCLUSION: High salivary α-amylase is associated with a high rate of temporomandibular joint noise and dental attrition, and a low rate of bruxism among elderly participants.