RESUMO
Objectives: A mucous retention cyst is a common, asymptomatic lesion that may cause complications during or after the sinus lift procedure. The goal of this study is to assess the effectiveness of the Croco Eye Technique (CET), which allows simultaneous excision of the cyst and sinus floor elevation. Methods: The technique was thoroughly described in two versions, and the group of 33 patients was analyzed. Patients who qualified for this procedure had insufficient alveolar ridge height, and their CBCT showed radiological images typical for retention cysts. Analyzed parameters included the version of CET, demographic data, anatomical parameters, intraoperative complications, recurrence of the cyst, success rate of the sinus lift and implants, and the follow-up period. Results: Out of the 33 cases, 9 were of the primary version (27.27%) and 24 of the final version (72.73%). The average height of a retention cyst was 24.05 mm, with the average alveolar ridge height of 1.86 mm. In three cases (9.09%), implants were placed immediately. The prevalence of uncontrolled Schneiderian membrane perforation was reduced from 55.56% to 4.17% between the primary and final versions. The cyst's recurrence rate was 3.13%. The implant survival rate was 100%. The mean follow-up period was 48.625 months (max 110 months). Conclusions: The Croco Eye Technique, despite the perforation of the Schneiderian membrane, enables successful sinus lift and implantation with a success rate of 100%. Excision of the retention cyst, which is the cause of perforation, allows for limiting the risk of the cyst's recurrence.
RESUMO
In this study, the authors analyzed modern resin materials typically used for temporary reconstructions on implants and manufactured via 3D printing. Three broadly used resins: NextDent Denture 3D, NextDent C&B MFH Bleach, and Graphy TC-80DP were selected for analysis and compared to currently used acrylic materials and ABS-like resin. In order to achieve this, mechanical tests were conducted, starting with the static tensile test PN-EN. After the mechanical tests, analysis of the chemical composition was performed and images of the SEM microstructure were taken. Moreover, numerical simulations were conducted to create numerical models of materials and compare the accuracy with the tensile test. The parameters obtained in the computational environment enabled more than 98% correspondence between numerical and experimental charts, which constitutes an important step towards the further development of numeric methods in dentistry and prosthodontics.
RESUMO
To date, there is no systematic anatomical classification available that could help clinicians in choosing between the lateral and palatal approach in sinus lift procedures. The aim was to provide a simple-to-use and memorable classification of the maxillary sinus concerning the thickness of lateral and palatal walls to facilitate the most adequate choice for the window location during direct sinus floor elevation. Cone beam computed tomography scans were consecutively obtained for 200 maxillary sinuses of patients needing dental implant placement with potential maxillary sinus augmentation. The thickness and height of the alveolar bone of the lateral and palatal walls of the maxillary sinuses were assessed. Four variants were distinguished. Class 0: an adequate sub-sinus residual bone height; without the need for sinus floor augmentation. Classes 1-3 had a reduced sub-sinus residual bone height. Class 1: a thinner lateral than palatal sinus wall. Class 2 (the most frequent; 49%): the comparable thickness of both walls in which either lateral, palatal, or crestal window osteotomies can be applied. Class 3 (the least frequent; 3%): a thinner palatal sinus wall in comparison to the lateral wall. The presented anatomical classification simplifies the decision-making process of choosing the most adequate window location and osteotomy technique.
RESUMO
Three-dimensional bioprinting technology appears to be a promising solution for the treatment and reconstruction of a wide range of maxillofacial bone defects. In this review, the authors discuss different bioprinting solutions and options in the context of the 4 factors of bone healing: structures or scaffolds, osteogenic cells, growth factors, and stabilization (diamond concept of healing), as well as the influence of a 5th factor - vascularization. Bone is a complex tissue; hence, bone bioprinting may require different technical approaches and mixed methods. Ultraviolet (UV) crosslinkable hydrogels, such as gelatin methacryloyl (GelMA), are among the most promising bioinks; they are enhanced by hydroxyapatite or 1-2.5 mm beta-tricalcium phosphate (ß-TCP) granules and porous scaffolds with recommended pore sizes greater than 300 µm. The advantages of mesenchymal stem cells (MSCs) are their significant availability, low tumorigenicity, and great potential for differentiation into osteoblasts or endothelial cells (ECs). Although growth factors require advanced delivery systems, they provide excellent improvement in the functionality of printed tissues. A proper vasculature system supplies cells with oxygen and nutrients, removes waste products, promotes osteogenesis, prevents ischemic necrosis, and improves the mechanical properties of bone. With all of these aspects perfectly balanced and working in synergy, the clinical use of bioprinting is only a matter of time.