Comparative biomechanical analysis of reconstruction and cephalomedullary nails in the treatment of osteoporotic subtrochanteric fractures.

INTRODUCTION: This study aimed to compare the biomechanical properties of two types of intramedullary nails - reconstruction nails (RCN) and cephalomedullary nails (CMN) - each with different proximal fixations, in a model of an osteoporotic subtrochanteric femoral fracture. This study focused on assessing stiffness and load to failure of RCN and CMN nails to provide insight into their clinical applications in osteoporotic fracture treatments. MATERIALS AND METHODS: Ten synthetic osteoporotic femoral models were used to generate a comminuted subtrochanteric fracture model. Five femurs were fixed using an RCN, and the remaining five were fixed using a CMN. The constructs were subjected to axial compression to measure their structural stiffness, load to failure, and failure modes. RESULTS: The CMN group demonstrated a slightly higher load to failure (mean, 2250 N) than the RCN group (mean, 2100 N), which was statistically significant (p = 0.008). However, the stiffness in both groups was statistically similar (RCN, 250 N/mm; CMN, 255 N/mm; p = 0.69). Both groups showed a load to failure exceeding 1500 N, a typically exerted load on the femoral head by a 75 kg individual. The failure patterns differed, with CMN failures starting at the nail insertion area and RCN failures starting at the reconstruction screw area. CONCLUSION: The RCN offers stiffness comparable to that of the CMN; although its load to failure is slightly lower than that of the CMN, it still exceeds the physiological tolerance limit. These findings suggest that the RCN is a viable alternative for treating osteoporotic subtrochanteric fractures.

Induced membrane technique with plate fixation has a lower complication rate than bone transport over a plate for segmental tibial defects larger than 5 cm.

INTRODUCTION: The treatment of segmental tibial bone defects remains a surgical challenge. While Bone Transport (BT) and Induced Membrane Technique (IMT) are effective strategies for regenerating bone, there are few comparative studies between them. This investigation undertakes a comparative analysis of BT and IMT for large segmental tibial defects stabilised through plate fixation. MATERIALS AND METHODS: Patients with segmental tibial defects exceeding 5 cm were prospectively enrolled from 2008 to 2021 in a single institution, with a minimum follow-up duration of two years. All patients underwent either BT or IMT with plate fixation of the tibia. Procedural success, primary union as well as bone and functional outcome scores were compared. Complications, including non-unions, joint contractures and deep infections requiring surgical intervention, were also compared. RESULTS: 41 patients were recruited in total. 28 patients underwent Bone Transport Over a Plate (BTOP), while 13 patients underwent IMT with Plate fixation (IMTP). The procedural success rate trended higher in IMTP compared to BTOP (100% vs. 85.7%). The primary union rate also trended higher in IMTP compared to BTOP (92.3% vs. 79.2%). BTOP and IMTP achieved similar rates of satisfactory bone outcome scores (78.6% vs. 84.6%) and functional outcome scores (75% vs. 76.5%). There was no statistical difference between procedural success, primary union, bone and functional outcome scores. The complication rate in BTOP was 78.6% (22 of 28), including five docking site or regenerate non-unions, eight deep infections and nine joint contractures. IMTP had a 38.5% (5 of 13) complication rate, including one non-union, two deep infections and two joint contractures. The complication rate was 2.04 times higher in BTOP compared to IMTP (p = 0.0117). CONCLUSIONS: BTOP and IMTP are both equally effective techniques for regenerating bone in large tibial bone defects. However, IMTP may be a safer procedure than BTOP, with a lower probability of requiring additional procedures to address complications.

Effect of cholesterol variability on the incidence of cataract, dementia, and osteoporosis: A study using a common data model.

The effects of cholesterol variability on cataracts, dementia, and osteoporosis remain controversial. Using a common data model, we investigated the effects of variations in cholesterol levels on the development of cataracts, dementia, and osteoporosis. Patients who received statin therapy between 2011 and 2020 and those with 3 or more tests for total cholesterol (TC), low-density lipoprotein cholesterol (LDL-C), high-density lipoprotein cholesterol (HDL-C), and triglyceride (TG) levels were included. The patients were divided into those with a coefficient of variation (CV) of TC higher than the mean (high-CV group) and those with a lower CV of TC (low-CV group). Moreover, 1:1 propensity score matching was conducted based on demographic variables. Cataract, dementia, or osteoporosis was defined as having a diagnostic, drug, or surgical code based on the cohort definition. Of the 12,882 patients, cataracts, dementia, and osteoporosis were developed in 525 (4.1%), 198 (1.5%), and 438 (3.4%) patients, respectively. The stratified Cox proportional hazards model showed that the incidences of cataracts and osteoporosis were 1.38 and 1.45 times greater in the high-CV group than in the low-CV group, respectively. Our study revealed that TC variability is associated with developing cataracts and osteoporosis.

Reliability of reverse sural artery fasciocutaneous flap in older adult patients: Comparison study between older and younger patients.

BACKGROUND: The reverse sural artery fasciocutaneous (RSAF) flap is a popular option for patients with soft tissue defects of the distal lower extremities. However, most studies have focused on young patients without comorbidities. This study aimed to report the clinical application of the RSAF flap and to evaluate its reliability in older adult patients. METHODS: A retrospective study of fifty-one patients who underwent RSAF flap was included in this study between September 2016 and October 2021. Reconstruction outcomes and wound complications were compared between groups A (21 patients over 60 years of age) and B (30 patients under 60 years of age). RESULTS: Overall, 74.5% of the flaps healed primarily. The demographics of the two groups were similar, except for comorbidities (P = 0.01). The risk factors that affected the survival of RSAF flaps were not significantly different between the two groups (P > 0.05). The rate of wound complications in group A (42.85%) was significantly higher than that in group B (13.3%) (P = 0.04). However, all wound complications were treated using a simple procedure (skin grafting or simple suturing). CONCLUSIONS: The RSAF flap can be a reliable salvage option to repair soft tissue defects of the lower extremities in older adult patients. It is safe and easy to harvest and transfer the flap; however, surgeons should be aware of the possibility of wound complications in older patients with comorbidities.

Minimally Invasive Derotational Osteotomy of Long Bones: Smartphone Application Used to Improve the Accuracy of Correction.

Correction of rotational malalignments caused by fractures is essential as it may cause pain and gait disturbances. This study evaluated the intraoperative use of a smartphone application (SP app) to measure the extent of corrective rotation in patients treated using minimally invasive derotational osteotomy. Intraoperatively, two parallel 5 mm Schanz pins were placed above and below the fractured/injured site, and derotation was performed manually after percutaneous osteotomy. A protractor SP app was used intraoperatively to measure the angle between the two Schanz pins (angle-SP). Intramedullary nailing or minimally invasive plate osteosynthesis was performed after derotation, and computerized tomography (CT) scans were used to assess the angle of correction postoperatively (angle-CT). The accuracy of rotational correction was assessed by comparing angle-SP and angle-CT. The mean preoperative rotational difference observed was 22.1°, while the mean angle-SP and angle-CT were 21.6° and 21.3°, respectively. A significant positive correlation between angle-SP and angle-CT was observed, and 18 out of 19 patients exhibited complete healing within 17.7 weeks (1 patient exhibited nonunion). These findings suggest that using an SP app during minimally invasive derotational osteotomy can result in accurate correction of malrotation of long bones in a reproducible manner. Therefore, SP technology with integrated gyroscope function represents a suitable alternative for determination of the magnitude of rotational correction when performing corrective osteotomy.

Application of an Intraoperative Limb Positioner for Adjustable Traction in Both-Column Fractures of the Acetabulum: A Technical Note with Clinical Outcome.

Traction of the ipsilateral leg is usually required to facilitate fracture reduction while operating both-column acetabular fractures. However, it is challenging to maintain constant traction manually during the operation. Herein, we surgically treated such injuries while maintaining traction using an intraoperative limb positioner and investigated the outcomes. This study included 19 patients with both-column acetabular fractures. Surgery was performed after the patient's condition had stabilized, at an average of 10.4 days after injury. The Steinmann pin was transfixed to the distal femur and connected to a traction stirrup; subsequently, the construct was affixed to the limb positioner. A manual traction force was applied through the stirrup and maintained with the limb positioner. Using a modified Stoppa approach combined with the lateral window of the ilioinguinal approach, the fracture was reduced, and plates were applied. Primary union was achieved in all cases at an average of 17.3 weeks. The quality of reduction at the final follow-up was found to be excellent, good, and poor in 10, 8, and 1 patients, respectively. The average Merle d'Aubigné score at the final follow-up was 16.6. Surgical treatment of both-column acetabular fracture using intraoperative traction with a limb positioner yields satisfactory radiological and clinical outcomes.

Prophylactic Femoral Neck Fixation in an Osteoporosis Femur Model: A Novel Surgical Technique with Biomechanical Study.

Intramedullary nailing (IMN) is a popular treatment for elderly patients with femoral shaft fractures. Recently, prophylactic neck fixation has been increasingly used to prevent proximal femoral fractures during IMN. Therefore, this study aimed to investigate the biomechanical strength of prophylactic neck fixation in osteoporotic femoral fractures. An osteoporotic femur model was created to simulate the union of femoral shaft fractures with IMN. Two study groups comprising six specimens each were created for IMN with two standard proximal locking screws (SN group) and IMN with two reconstruction proximal locking screws (RN group). Axial loading was conducted to measure the stiffness, load-to-failure, and failure modes. There were no statistically significant differences in stiffness between the two groups. However, the load-to-failure in the RN group was significantly higher than that in the SN group (p < 0.05). Femoral neck fractures occurred in all specimens in the SN group. Five constructs in the RN group showed subtrochanteric fractures without femoral neck fractures. However, one construct was observed in both subtrochanteric and femoral neck fractures. Therefore, prophylactic neck fixation may be considered an alternative biomechanical solution to prevent proximal femoral fractures when performing IMN for osteoporotic femoral fractures.

The role of an augmentative plating in the management of femoral subtrochanteric nonunion.

INTRODUCTION: Owing to its distinct biomechanical properties, nonunion is common (7-20%) after intramedullary (IM) nailing of subtrochanteric femoral fractures. Unlike diaphyseal nonunion, it is difficult to provide sufficient stability by exchanging nailing alone in subtrochanteric nonunion. This study investigated the clinical outcomes of femoral subtrochanteric nonunion initially treated with an IM nail and subsequently managed with minimally invasive augmentative plate fixation. MATERIALS AND METHODS: Nineteen patients were enrolled retrospectively. The mechanisms of initial injury were traffic accidents in 8, falls from a height in seven, and slipping in two patients. Two patients with atypical subtrochanteric femoral fractures without a specific trauma history were further included. All patients underwent IM nailing as the index operation. Nonunion surgery was performed an average of 45.2 weeks after the initial surgery. In cases of hardware damage and/or atrophic nonunion, exchange nailing and bone grafting were performed in addition to augmentative plating, as necessary. Conversely, augmentative plating alone was performed in cases of hypertrophic nonunion without any failure of the preexisting IM nail or malalignment. A narrow locking compression plate was fixed after contouring according to the shape of the proximal femur. The mean follow-up period was 36.1 months. RESULTS: Bony union was achieved in 18/19 patients (94.7%), at an average of 19.8 weeks after nonunion surgery. In the case that did not heal even after exchange nailing, additional plating and bone grafting, further autogenous bone grafting was required after 11 months, which healed uneventfully. There were 2 cases of soft tissue irritation over the plate, but no major complications were observed. CONCLUSIONS: Additional plate augmentation over a retained IM nail yields satisfactory outcomes in terms of the bony union in subtrochanteric nonunion. Given its expected biomechanical superiority and relatively easy surgical technique, it may be a reasonable option for the management of femoral subtrochanteric nonunion.

Superior capsular reconstruction using hybrid graft for irreparable massive rotator cuff tear.

PURPOSE: To evaluate the clinical and radiological outcomes of arthroscopic superior capsular reconstruction (SCR) using hybrid grafts composed of tensor fascia lata autografts and human dermal allografts. METHODS: This study included 30 patients with chronic irreparable posterosuperior rotator cuff tears (RCTs) who underwent arthroscopic SCR using a hybrid graft composed of tensor fascia lata autograft and human dermal allograft. Clinical outcomes were evaluated using the pain visual analogue scale score, shoulder range of motion, American Shoulder and Elbow Surgeons score, constant score, University of California-Los Angeles score, and simple shoulder test score preoperatively and at least 2 years after surgery. Radiographic analysis included the Hamada classification grade, acromiohumeral distance (AHD), and graft integrity at 2 years after surgery. RESULTS: All patients exhibited significant clinical improvement in all functional outcome measurements, except external rotation (all P < 0.05). The number of patients who exhibited pseudoparalysis decreased from 7 (23.3%) to 2 (6.7%) postoperatively. Complications were not observed. Radiologically, the mean postoperative AHD increased significantly from 6.9 ± 1.6 cm to 8.8 ± 2.1 cm at 2 years postoperatively (P < 0.001). Twenty five out of the 30 (83.3%) patients showed successful graft healing, and all healing failures occurred on the humeral side. The differences between the healed-graft and failed-graft groups were significantly lower graft thickness (P = 0.001) and smaller AHD (P < 0.001) in the failed-graft group. Every functional outcome scores were not statistically different between healed-graft and failed-graft groups. CONCLUSIONS: An arthroscopic SCR technique using a hybrid graft consisting of a tensor fascia lata autograft and human dermal allograft showed satisfactory clinical outcomes in patients with irreparable RCTs. LEVEL OF EVIDENCE: IV.

rhBMP-2-Conjugated Three-Dimensional-Printed Poly(L-lactide) Scaffold is an Effective Bone Substitute.

BACKGROUND: Bone growth factors, particularly bone morphogenic protein-2 (BMP-2), are required for effective treatment of significant bone loss. Despite the extensive development of bone substitutes, much remains to be desired for wider application in clinical settings. The currently available bone substitutes cannot sustain prolonged BMP-2 release and are inconvenient to use. In this study, we developed a ready-to-use bone substitute by sequential conjugation of BMP to a three-dimensional (3D) poly(L-lactide) (PLLA) scaffold using novel molecular adhesive materials that reduced the operation time and sustained prolonged BMP release. METHODS: A 3D PLLA scaffold was printed and BMP-2 was conjugated with alginate-catechol and collagen. PLLA scaffolds were conjugated with different concentrations of BMP-2 and evaluated for bone regeneration in vitro and in vivo using a mouse calvarial model. The BMP-2 release kinetics were analyzed using ELISA. Histological analysis and micro-CT image analysis were performed to evaluate new bone formation. RESULTS: The 3D structure of the PLLA scaffold had a pore size of 400 µm and grid thickness of 187-230 µm. BMP-2 was released in an initial burst, followed by a sustained release for 14 days. Released BMP-2 maintained osteoinductivity in vitro and in vivo. Micro-computed tomography and histological findings demonstrate that the PLLA scaffold conjugated with 2 µg/ml of BMP-2 induced optimal bone regeneration. CONCLUSION: The 3D-printed PLLA scaffold conjugated with BMP-2 enhanced bone regeneration, demonstrating its potential as a novel bone substitute.

Incomplete Diaphyseal Atypical Femoral Fracture due to Increased Anterolateral Bowing: Treatment with Corrective Osteotomy and Intramedullary Nailing with Augmented Plate Fixation.

BACKGROUND: Increased anterolateral bowing of the femur is associated with atypical femoral fractures among older patients (including both those receiving and those not receiving treatment with bisphosphonates) as well as a greater likelihood of occurring in the diaphyseal versus the subtrochanteric region. Prophylactic intramedullary (IM) nailing is recommended for the treatment of incomplete atypical femoral fractures, which are radiographically evident. However, this bowing deformity is considered to be a major obstacle to IM nailing as it may be associated with postoperative complications. Corrective osteotomy combined with IM nailing straightens the exaggerated curvature of the femur. We hypothesized that this technique may lead to the safe and rapid healing of incomplete diaphyseal atypical femoral fractures, thereby reducing lateral tensile stress. METHODS: From October 2015 through March 2020, 17 female patients (20 femora) with a mean age of 76.1 years (range, 68 to 86 years) underwent a surgical procedure for the treatment of an incomplete diaphyseal atypical femoral fracture associated with anterolateral bowing. The surgical technique consisted of minimally invasive osteotomy and reconstruction with use of IM nailing, with or without an augmentation plate. Preoperative and postoperative radiographic findings (lateral and anterior bowing angles, anterolateral bowing grade, and lateral distal femoral angle [LDFA]) were compared. Primary union, time to union, and complications were evaluated as the outcomes. RESULTS: Primary bone union was achieved in 19 of the 20 femora at a mean of 24.9 weeks (range, 20 to 40 weeks). There were 2 instances of delayed union, which healed at 36 and 40 weeks. The lateral bowing angle, anterior bowing angle, and LDFA significantly improved postoperatively (from 12.0° to 3.3°, from 17.3° to 11.5°, and from 93.5° to 88.8°, respectively) (p < 0.001). There was 1 instance of nonunion, which healed after plate augmentation without a bone graft. CONCLUSIONS: Given the pathophysiology of elevated lateral tensile stress, corrective osteotomy and IM nailing may be an acceptable solution for the treatment of incomplete diaphyseal atypical femoral fractures associated with increased anterolateral bowing. LEVEL OF EVIDENCE: Therapeutic Level III . See Instructions for Authors for a complete description of levels of evidence.

Results and Factors Affecting Clinical Efficacy of Medial Patellofemoral Ligament Reconstruction Using a Gracilis Tendon Suture Technique.

Background: This study evaluated the outcomes of medial patellofemoral ligament (MPFL) reconstruction using a gracilis tendon suture technique for patients with patellar instability. Potential factors affecting clinical efficacy were also evaluated. Methods: This study included 22 patients diagnosed with patellar instability, who underwent MPFL reconstruction using a gracilis tendon. Their mean age was 21.5 years (range, 15-48 years), and the mean follow-up period was 26.8 months (range, 12-66 months). Clinical evaluation included the determination of Kujala, Lysholm, and Tegner scores. Radiographic evaluation included changes in congruence angle and arthritic changes in the patellofemoral joint. Additionally, patients were examined for any complications, including recurrent dislocation. Factors affecting clinical efficacy were also evaluated. Results: All clinical scores improved at final follow-up. The mean congruence angle improved from 23.6° before surgery to -6.5° at final follow-up. Two of 15 patients developed osteoarthritic changes in the patellofemoral joint. Dislocation recurred in 2 patients with type C trochlear dysplasia, which showed a statistically significant association with recurrent dislocation when compared to type A and B dysplasia (p = 0.026). Kujala scores were significantly lower among patients with abnormal patellar tilts (p = 0.038), and Lysholm scores were significantly lower among patients with femoral internal rotation deformity (p = 0.024). Conclusions: Satisfactory results were obtained after MPFL reconstruction using a gracilis tendon suture technique for patients with patellar instability. However, dislocation recurred in patients with type C trochlear dysplasia, and clinical efficacy was lower among patients with femoral internal rotation and patellar tilt.

Effects of a graphene oxide-alginate sheet scaffold on rotator cuff tendon healing in a rat model.

BACKGROUND: Natural polymer scaffolds used to promote rotator cuff healing have limitations in terms of their mechanical and biochemical properties. This animal study aimed to investigate the effects of combined graphene oxide (GO) and alginate scaffold and the toxicity of GO on rotator cuff healing in a rat model. METHODS: First, the mechanical properties of a GO/alginate scaffold and a pure alginate scaffold were compared. The in vitro cytotoxicity of and proliferation of human tenocytes with the GO/alginate scaffold were evaluated by CCK-8 assay. For the in vivo experiment, 20 male rats were randomly divided into two groups (n = 10 each), and supraspinatus repair was performed: group 1 underwent supraspinatus repair alone, and group 2 underwent supraspinatus repair with the GO/alginate scaffold. Biomechanical and histological analyses were performed to evaluate the quality of tendon-to-bone healing 8 weeks after rotator cuff repair. RESULTS: The GO/alginate scaffold exhibited an increased maximum load (p = .001) and tensile strength (p = .001). In the cytotoxicity test, the cell survival rate with the GO/alginate scaffold was 102.08%. The proliferation rate of human tenocytes was no significant difference between the GO/alginate and alginate groups for 1, 3, 5, and 7 days. Biomechanically, group 2 exhibited a significantly greater ultimate failure load (p < .001), ultimate stress (p < .001), and stiffness (p < .001) than group 1. The histological analysis revealed that the tendon-to-bone interface in group 2 showed more collagen fibers bridging, tendon-to-bone integration, longitudinally oriented collagen fibers, and fibrocartilage formation than in group 1. CONCLUSION: A small amount of GO added to alginate improved the mechanical properties of the scaffold without evidence of cytotoxicity. At 8 weeks after rotator cuff repair, the GO/alginate scaffold improved tendon-to-bone healing without causing any signs of toxicity in a rat model.

Increased interleukin-6 and TP53 levels in rotator cuff tendon repair patients with hypercholesterolemia.

BACKGROUND: A previous study reported that hyperlipidemia increases the incidence of tears in the rotator cuff tendon and affects healing after repair. The aim of our study was to compare the gene and protein expression of torn rotator cuff tendons in patients both with and without hypercholesterolemia. METHODS: Thirty patients who provided rotator cuff tendon samples were classified into either a non-hypercholesterolemia group (n=19, serum total cholesterol [TC] <200 mg/dL) and hypercholesterolemia group (n=11, serum TC ≥240 mg/dL) based on their concentrations of serum TC. The expression of various genes of interest, including COL1A1, IGF1, IL-6, MMP2, MMP3, MMP9, MMP13, TNMD, and TP53, was analyzed by real-time quantitative reverse transcription polymerase chain reaction (qRT-PCR). In addition, Western blot analysis was performed on the proteins encoded by interleukin (IL)-6 and TP53 that showed significantly different expression levels in real-time qRT-PCR. RESULTS: Except for IGF1, the gene expression levels of IL-6, MMP2, MMP9, and TP53 were significantly higher in the hypercholesterolemic group than in the non-hypercholesterolemia group. Western blot analysis confirmed significantly higher protein levels of IL-6 and TP53 in the hypercholesterolemic group (p<0.05). CONCLUSIONS: We observed an increase in inflammatory cytokine and matrix metalloproteinase (MMP) levels in hypercholesterolemic patients with rotator cuff tears. Increased levels of IL-6 and TP53 were observed at both the mRNA and protein levels. We suggest that the overexpression of IL-6 and TP53 may be a specific feature in rotator cuff disease patients with hypercholesterolemia.

Mid-term to Long-term Follow-up Results of Reconstruction for Thumb Radial Polydactyly.

BACKGROUND: Preaxial or radial polydactyly is one of the most common hand congenital anomalies in newborns. Contemporary reconstruction methods include ligament reconstruction, excision of the polydactylous thumb, osteotomy, and other surgical techniques according to the type of polydactyly. The purpose of this study was to report mid-term to long-term reconstruction results for thumb (radial) polydactyly. METHODS: We retrospectively reviewed the medical records of patients who underwent reconstruction surgery for preaxial polydactyly. Clinical outcomes, including the range of motion (ROM), pain, and complications, were evaluated. We assessed the final radiographs of the reconstructed thumb to identify the potential development of arthritis or other remaining deformities. After excluding cases without a simple radiograph and cases with a short follow-up period of fewer than 5 years, 26 thumbs were included. The surgical technique followed including excision of polydactylout thumb was tailored to the type of polydactyly. If the nail size of the thumbs was similar, the Bilhaut-Cloquet method was preferred. RESULTS: The mean age of the patients at the surgery and final follow-up was 14.9 months (range: 8 to 30 mo) and 11.9 years (range: 5.8 to 19.3 y), respectively. The mean follow-up was 128.8 months years (range: 60 to 219 mo), and the mean ROM of the thumb was 32.7 and 57.5 degrees in the distal interphalangeal joint (DIP) and metacarpophalangeal (MP) joint, respectively. Ulnar or radial side instability was prominent in 7 patients in the involved joints (26.9%). One patient underwent interphalangeal (IP) fusion for extension lag with pain. The radiologic evaluation revealed that 2 patients developed radiographic evidence of IP joint arthritis (7.7%). Radial deviation of the MP or IP joint existed in 13 cases (range: 5 to 40 degrees) (50.0%), and ulnar deviation of the MP or IP joint existed in 2 cases (range: 19 to 20 degrees) (7.7%). CONCLUSIONS: In mid-term to long-term experience, sequelae such as joint instability, joint stiffness, and remaining deformity cannot be neglected. An unstable MP joint may result if the DIP joint remains stiff or has a lower ROM. LEVEL OF EVIDENCE: Level IV-therapeutic studies.

Treatment of Critical-Sized Bone Defects Involving the Ankle Joints: Staged Tibiotalocalcaneal Arthrodesis With Induced Membrane Technique and Intramedullary Nail.

OBJECTIVES: To report the outcomes of staged tibiotalocalcaneal (TTC) arthrodesis for critical-sized bone defects involving the ankle joints. DESIGN: Retrospective review of case series. SETTING: Two academic Level 1 trauma centers. PATIENTS/PARTICIPANTS: The study included 20 patients with critical-sized (≥2 cm) segmental bone defects around the ankle joints. INTERVENTION: Staged TTC arthrodesis was performed with induced membrane technique and retrograde intramedullary nail. MAIN OUTCOME MEASUREMENTS: We investigated the radiological evaluation, including modified radiographic union scale for tibia fractures score, time to union, and leg length discrepancy, and functional outcomes using foot and ankle outcome score and American Orthopaedic Foot and Ankle Society ankle-hindfoot score. RESULTS: The average bone defect was 6.4 cm (range: 2.4-12.3). Two of the 20 (10%) patients developed recurrence of infection. Fifteen patients (75%) achieved primary healing. Three patients (15%) were treated with repeated bone grafting and additional plating. The average time to union and leg length discrepancy were 10 months (range: 5-21) and 9 mm (range: 0-31), respectively. The mean foot and ankle outcome score and American Orthopaedic Foot and Ankle Society ankle-hindfoot score were 63 (range: 52-71) and 74 (range: 64-81), respectively. CONCLUSIONS: Staged TTC arthrodesis with induced membrane technique and intramedullary nail can be an effective treatment method for critical-sized bone defects involving the ankle joints. LEVEL OF EVIDENCE: Therapeutic Level IV. See Instructions for Authors for a complete description of levels of evidence.

Intramedullary nailing of subtrochanteric fractures in elderly patients: Comparative study of helical blade cephalomedullary nail versus reconstruction nail.

INTRODUCTION: Intramedullary nailing (IMN), which is a common method for treating subtrochanteric fractures, is conducted as cephalomedullary (CMN) or reconstruction (RCN) nailing. Numerous studies have reported the effectiveness of CMN, which requires a shorter surgery time and provides stronger fixation strength with blade-type devices. However, the radiographic and clinical outcomes of the use of CMN and RCN in elderly patients aged ≥65 years have not been compared yet. This study aimed to investigate whether CMN offers superior outcomes over RCN in the treatment of subtrochanteric fractures in elderly patients. MATERIALS AND METHODS: This retrospective study included 60 elderly patients (17 men and 43 women; mean age: 74.9 years) diagnosed with subtrochanteric fractures and treated with IMN with helical blade CMN (CMN group: 30 patients) or RCN (RCN group: 30 patients) between January 2013 and December 2018 with at least 1 year of follow-up period. Radiologic outcomes were evaluated based on the postoperative state of alignment and the achievement and timing of bony union at the final follow-up. Clinical outcomes were evaluated using the Merle d'Aubigné-Postel score. Radiologic and clinical outcomes in the two groups were compared and analyzed, and the occurrence of complications was examined. RESULTS: The difference in malalignment between the two groups was not significant; however, the RCN group achieved more effective reduction. At the final follow-up, bony union was achieved within 18.9 weeks, on average, in 28 patients in the CMN group and within 21.6 weeks, on average, in 27 patients in the RCN group. Twenty patients in the CMN group and 26 in the RCN group showed good or better results according to the Merle d'Aubigné-Postel score. No significant differences were found for any of the parameters. CONCLUSIONS: In the treatment of difficult subtrochanteric fractures in elderly patients, RCN can provide excellent reduction and strong fixation similar to CMN and can result in outstanding clinical and radiologic outcomes.

The importance of reconstruction nailing for diaphyseal atypical femoral fractures: a comparative study with standard nailing.

INTRODUCTION: Subtrochanteric atypical femoral fractures (AFFs) usually require long cephalomedullary or reconstruction nailing to achieve satisfactory healing. Recently, this type of nailing has also been recommended to fix diaphyseal AFFs and prevent fragility fractures around the proximal femur, although standard antegrade nailing seems sufficient from a biomechanical perspective. This study aimed to compare treatment outcomes and complications between reconstruction and standard nailing for diaphyseal AFFs. MATERIALS AND METHODS: A retrospective comparative study of 48 female patients with diaphyseal AFFs who underwent surgical treatment with either reconstruction or standard nailing was conducted. The reconstruction nailing group comprised 23 patients with a mean age of 74.4 years and included 16 complete and 7 incomplete AFFs. The mean follow-up period was 30 months. The standard nailing group comprised 25 patients with a mean age of 71.1 years and included 16 complete and 9 incomplete AFFs. The mean follow-up period was 57.8 months. The healing rate, time to union, and complications were analyzed and compared between the two groups. RESULTS: Bony union was achieved in all 23 cases (100%) of the reconstruction nailing group by a mean of 19.3 weeks postoperative. In the standard nailing group, 23 of 25 cases healed (92%) by a mean of 16 weeks postoperative. The standard nailing group included two delayed fragility fractures of the femoral neck (5 and 10 years after the initial surgery), four cases of newly developed subtrochanteric AFFs at the distal screw of the proximal interlocking screws of the nail (one complete and three incomplete fractures), and two cases of nonunion. Complications only occurred in the standard nailing group (p = 0.01, Fisher's exact test). CONCLUSIONS: In diaphyseal AFFs, reconstruction nailing may achieve a satisfactory outcome and can also decrease delayed peri-implant fragility fractures of the hip, newly developed subtrochanteric AFFs, and nonunion.

Poller (blocking) screw with intramedullary femoral nailing for subtrochanteric femoral non-unions: clinical outcome and review of concepts.

INTRODUCTION: Surgery to treat nonunion resulted from malalignment is challenging since correction and bone union should be achieved simultaneously. To report the clinical outcomes achieved through reconstruction of sub-trochanteric femoral fractures by femoral nailing using a poller screw and to review the current concepts. MATERIALS AND METHODS: Fourteen patients (11 men and 3 women; mean age 56.4 years) who were diagnosed with non-union of subtrochanteric femoral fractures and who underwent intramedullary nailing with blocking screws between August 2013 and March 2019, with at least 1 year follow-up, were analyzed retrospectively. The preoperative and postoperative Centrum-Collum-Diaphyseal angle and anterior angulation angle were measured. Bone union time, position and number of poller screws used, and complications were analyzed. Functional assessment was performed by evaluating the Harris hip score. The related literature was searched, and 14 clinical studies on the treatment of sub-trochanteric non-union were analyzed. RESULTS: Bone union was achieved in 12/14 cases (85.7%) at the final follow-up within a mean of 6.52 (3-12) months. Bone union was also achieved in two patients lacking bone union at the final follow-up through bone grafting and augmented plating. No cases developed complications, including infection and bone necrosis, and the varus deformity and anterior angulation significantly improved from a preoperative mean of 12.4° and 9.4° to postoperative mean 3.8° and 2.4°, respectively. The mean Harris hip score at the final follow-up was 87.07 (73-98) points. Analysis of published literature revealed high rates of bone union (78-100%) through various fixation methods. CONCLUSION: Correction with blocking screws and rigid fixation with intramedullary nailing to treat sub-trochanteric-non-union-caused malalignment can yield good clinical and radiological outcomes.

Peri-implant atypical femoral fracture after nail or plate osteosynthesis.

BACKGROUND: A lack of scientific information regarding the risk factors and diagnosis of peri-implant atypical femoral fracture (PI-AFF) exists. We report a case series of developed PI-AFF with a nail or plate construct wherein prior femoral fractures were already healed after osteosynthesis. This study aimed to identify the cause and risk factors of PI-AFF and to devise a preventive method based on this. METHODS: We identified 11 PI-AFFs displaying features of AFFs. All patients were ambulant females (mean age, 74.9 years). The mean T-score of the femur measured by DEXA (Dual Energy X-ray Absorptiometry) scan was 3.5. Osteosynthesis was performed with a plate and an intramedullary nail in six and five patients, respectively. Possible risk factors were investigated, including the used implant, the medication of bisphosphonate, the characteristics of previous fracture (AFF or non-AFF), and the co-existence of AFF on the contralateral side. RESULTS: The PI-AFFs developed at an average of 6.6 years from the time of prior fracture. All fractures were located at the screw through the plate or nail. Regarding anatomic locations, seven and four fractures were at the subtrochanteric area and diaphysis, respectively. Diaphyseal PI-AFFs occurred in plating cases, all of which were associated with excessive femoral bowing. Subtrochanteric PI-AFFs included all five patients with nail fixation, which occurred near a proximal interlocking screw. Six of the 11 patients were on bisphosphonate treatment before or at the time of fracture. The duration of bisphosphonate treatment was 6 years on average. Concerning the previous femoral fractures, seven and four patients were AFF and non-AFF, respectively. Considering the pathology on the contralateral leg, eight had suffered diaphyseal AFF. Four patients were treated nonoperatively. Seven patients needed an operation; 6 of them healed after reconstruction nailing, and one needed hip arthroplasty because of the associated displaced femoral neck fracture. CONCLUSIONS: PI-AFFs may develop through the screw hole at the subtrochanteric or diaphyseal area due to femoral fragility and stress riser effect of the implant. An improved osteosynthesis strategy may be necessary to avoid PI-AFFs when fixing osteoporotic femoral fractures.