Estimation of Axle Torque for an Agricultural Tractor Using an Artificial Neural Network.

The objective of this study was to develop a model to estimate the axle torque (AT) of a tractor using an artificial neural network (ANN) based on a relatively low-cost sensor. ANN has proven to be useful in the case of nonlinear analysis, and it can be applied to consider nonlinear variables such as soil characteristics, unlike studies that only consider tractor major parameters, thus model performance and its implementation can be extended to a wider range. In this study, ANN-based models were compared with multiple linear regression (MLR)-based models for performance verification. The main input data were tractor engine parameters, major tractor parameters, and soil physical properties. Data of soil physical properties (i.e., soil moisture content and cone index) and major tractor parameters (i.e., engine torque, engine speed, specific fuel consumption, travel speed, tillage depth, and slip ratio) were collected during a tractor field experiment in four Korean paddy fields. The collected soil physical properties and major tractor parameter data were used to estimate the AT of the tractor by the MLR- and ANN-based models: 250 data points were used for developing and training the model were used, the 50 remaining data points were used to test the model estimation. The AT estimated with the developed MLR- and ANN-based models showed agreement with actual measured AT, with the R2 value ranging from 0.825 to 0.851 and from 0.857 to 0.904, respectively. These results suggest that the developed models are reliable in estimating tractor AT, while the ANN-based model showed better performance than the MLR-based model. This study can provide useful results as a simple method using ANNs based on relatively inexpensive sensors that can replace the existing complex tractor AT measurement method is emphasized.

Simulation of Design Factors of a Clutch Pack for Power-Shift Transmission for an Agricultural Tractor.

The objective of this study is the simulation of the most affected design factors and variables of the clutch pack for the power-shift transmission (PST) of a tractor based measured data. The simulation model, the mathematical model of sliding velocity, a moment of inertia, and clutch engagement pressure of clutch pack were developed using the powertrain and configurations of the real PST tractor. In this study, the sensor fusion method was used to precisely measure the proportional valve pressure by test bench, which was applied to the simulation model. The clutch engagement times were found 1.20 s at all temperatures for determined factors. The engagement pressures have a significant difference at various temperatures (25 to 100 °C) of the hydraulic oils after the 1.20 s but the most affected factors were satisfied with the simulation conditions that ensure the clutch engagement on time. Finally, this sensor fusion method is believed to be helpful in realizing precision agriculture through minimization of power loss and maximum energy efficiency of tractors.

Development of a Real-Time Tillage Depth Measurement System for Agricultural Tractors: Application to the Effect Analysis of Tillage Depth on Draft Force during Plow Tillage.

The objectives of this study were to develop a real-time tillage depth measurement system for agricultural tractor performance analysis and then to validate these configured systems through soil non-penetration tests and field experiment during plow tillage. The real-time tillage depth measurement system was developed by using a sensor fusion method, consisting of a linear potentiometer, inclinometer, and optical distance sensor to measure the vertical penetration depth of the attached implement. In addition, a draft force measurement system was developed using six-component load cells, and an accuracy of 98.9% was verified through a static load test. As a result of the soil non-penetration tests, it was confirmed that sensor fusion type A, consisting of a linear potentiometer and inclinometer, was 6.34-11.76% more accurate than sensor fusion type B, consisting of an optical distance sensor and inclinometer. Therefore, sensor fusion type A was used during field testing as it was found to be more suitable for use in severe working environments. To verify the accuracy of the real-time tillage depth measurement system, a linear regression analysis was performed between the measured draft and the predicted values calculated using the American Society of Agricultural and Biological Engineers (ASABE) standards-based equation. Experimental data such as traveling speed and draft force showed that it was significantly affected by tillage depth, and the coefficient of determination value at M3-Low was 0.847, which is relatively higher than M3-High. In addition, the regression analysis of the integrated data showed an R-square value of 0.715, which is an improvement compared to the accuracy of the ASABE standard prediction formula. In conclusion, the effect of tillage depth on draft force of agricultural tractors during plow tillage was analyzed by the simultaneous operation of the proposed real-time tillage depth measurement system and draft force measurement system. In addition, system accuracy is higher than the predicted accuracy of ±40% based on the ASABE standard equation, which is considered to be useful for various agricultural machinery research fields. In future studies, real-time tillage depth measurement systems can be used in tractor power train design and to ensure component reliability, in accordance with agricultural working conditions, by predicting draft force and axle loads depending on the tillage depth during tillage operations.

Loss of MTUS1 Expression Is Associated With Poor Prognosis in Patients With Gallbladder Carcinoma.

BACKGROUND/AIM: Microtubule-associated scaffold protein 1 (MTUS1) acts as tumor suppressor in several cancer types. This study assessed the relationship between clinicopathological characteristics and expression of microRNA candidates based on MTUS1 expression in gallbladder cancer (GBC). MATERIALS AND METHODS: MTUS1 expression was evaluated by immunohistochemical staining of tissue microarrays from 109 cases of GBC. The association of MTUS1 expression with clinicopathological factors was explored. Two microRNA candidates (miR-19a-3p, and miR-19b-3p), which were identified by a literature review and computational analysis, were assessed in GBC tissue samples by quantitative real-time polymerase chain reaction. RESULTS: Low MTUS1 expression in GBC was associated with high histological grade, perineural invasion, lymphovascular invasion, high T-stage, advanced TNM stage, poorer disease-free survival, and poorer cancer-specific survival. No statistical association between MTUS1 expression and expression of microRNA candidates was observed. CONCLUSION: MTUS1 may act as tumor suppressor and might be a potential biomarker for predicting prognosis in GBC.