RESUMO
Optics-based measurement systems have been developed to measure the voltage and the current on a load of the Seoul National University X-pinch device [Ryu et al., Rev. Sci. Instrum. 92, 053533 (2021)]. A lithium niobate crystal that changes the polarization state of the propagating laser beam due to the Pockels effect induced by the electric field across the crystal, thus capable of measuring the voltage, is located next to the load. For the current measurement, an optic fiber is wound around the load to detect the change in the polarization state of the propagating laser beam due to the Faraday rotation induced by the magnetic field. As both voltage and current measurement systems utilize optical effects, the sensors, i.e., the lithium niobate crystal and the optic fiber, do not require any electrical grounds, in contrast to circuit-based probes, such as voltage dividers or Rogowski grooves. This facilitates an easy access to shield other required electronic devices, such as lasers and photodetectors, from the electromagnetic interference generated by the X-pinch power system. In addition, the sensors can be placed in close proximity to the load with fewer concerns on the electrical insulation. Temporal evolutions of the simultaneously measured voltage and current on the load of the X-pinch are successfully obtained and discussed.
RESUMO
In recent years, satellite communication systems (SCSs) have rapidly developed in terms of their role and capabilities, promoted by advancements in space launch technologies. However, this rapid development has also led to the emergence of significant security vulnerabilities, demonstrated through real-world targeted attacks such as AcidRain and AcidPour that demand immediate attention from the security community. In response, various countermeasures, encompassing both technological and policy-based approaches, have been proposed to mitigate these threats. However, the multitude and diversity of these proposals make their comparison complex, requiring a systemized view of the landscape. In this paper, we systematically categorize and analyze both attacks and defenses within the framework of confidentiality, integrity, and availability, focusing on specific threats that pose substantial risks to SCSs. Furthermore, we evaluate existing countermeasures against potential threats in SCS environments and offer insights into the security policies of different nations, recognizing the strategic importance of satellite communications as a national asset. Finally, we present prospective security challenges and solutions for future SCSs, including full quantum communication, AI-integrated SCSs, and standardized protocols for the next generation of terrestrial-space communication.
RESUMO
BACKGROUND: Detergent poisoning mostly occurs through oral ingestion (> 85%), ocular exposure (< 15%), or dermal exposure (< 8%). Reports of detergent poisoning through an intravenous injection are extremely rare. In addition, there are very few cases of renal toxicity directly caused by detergents. Here, we report a unique case of acute kidney injury caused by detergent poisoning through an accidental intravenous injection. CASE SUMMARY: A 61-year-old man was intravenously injected with 20 mL of detergent by another patient in the same room of a local hospital. The surfactant and calcium carbonate accounted for the largest proportion of the detergent. The patient complained of vascular pain, chest discomfort, and nausea, and was transferred to our institution. After hospitalization, the patient's serum creatinine level increased to 5.42 mg/dL, and his daily urine output decreased to approximately 300 mL. Renal biopsy findings noted that the glomeruli were relatively intact; however, diffuse acute tubular injury was observed. Generalized edema was also noted, and the patient underwent a total of four hemodiafiltration sessions. Afterward, the patient's urine output gradually increased whereas the serum creatinine level decreased. The patient was discharged in a stable status without any sequelae. CONCLUSION: Detergents appear to directly cause renal tubular injury by systemic absorption. In treating a patient with detergent poisoning, physicians should be aware that the renal function may also deteriorate. In addition, timely renal replacement therapy may help improve the patient's prognosis.
RESUMO
BACKGROUND: Tamoxifen (tam) is widely used to treat estrogen-positive breast cancer. However, cancer recurrence after chemotherapy remains a major obstacle to achieve good patient prognoses. In this study, we aimed to identify genes responsible for epigenetic regulation of tam resistance in breast cancer. METHODS: Methylation microarray data were analyzed to screen highly hypomethylated genes in tam resistant (tamR) breast cancer cells. Quantitative RT-PCR, Western blot analysis, and immunohistochemical staining were used to quantify expression levels of genes in cultured cells and cancer tissues. Effects of matrix metalloproteinase-1 (MMP1) expression on cancer cell growth and drug resistance were examined through colony formation assays and flow cytometry. Xenografted mice were generated to investigate the effects of MMP1 on drug resistance in vivo. RESULTS: MMP1 was found to be hypomethylated and overexpressed in tamR MCF-7 (MCF-7/tamR) cells and in tamR breast cancer tissues. Methylation was found to be inversely associated with MMP1 expression level in breast cancer tissues, and patients with lower MMP1 expression exhibited a better prognosis for survival. Downregulating MMP1 using shRNA induced tam sensitivity in MCF-7/tamR cells along with increased apoptosis. The xenografted MCF-7/tamR cells that stably expressed short hairpin RNA (shRNA) against MMP1 exhibited retarded tumor growth compared to that in cells expressing the control shRNA, which was further suppressed by tam. CONCLUSIONS: MMP1 can be upregulated through promoter hypomethylation in tamR breast cancer, functioning as a resistance driver gene. MMP1 can be a potential target to suppress tamR to achieve better prognoses of breast cancer patients.
RESUMO
Biodegradable polymers have been used with various systems for tissue engineering. Among them, poly(lactic-co-glycolic) acid (PLGA) has been widely used as a biomaterial for bone regeneration because of its great biocompatibility and biodegradability properties. However, there remain substantial cruxes that the by-products of PLGA result in an acidic environment at the implanting site, and the polymer has a weak mechanical property. In our previous study, magnesium hydroxide (MH) and bone extracellular matrix are combined with a PLGA scaffold (PME) to improve anti-inflammation and mechanical properties and osteoconductivity. In the present study, the development of a bioactive nanocomplex (NC) formed along with polydeoxyribonucleotide and bone morphogenetic protein 2 (BMP2) provides synergistic abilities in angiogenesis and bone regeneration. This PME hybrid scaffold immobilized with NC (PME/NC) achieves outstanding performance in anti-inflammation, angiogenesis, and osteogenesis. Such an advanced PME/NC scaffold suggests an integrated bone graft substitute for bone regeneration.
RESUMO
A substantial amount of research effort has been directed toward the development of Pt-based catalysts with higher performance and durability than conventional polycrystalline Pt nanoparticles to achieve high-power and innovative energy conversion systems. Currently, attention has been paid toward expanding the electrochemically active surface area (ECSA) of catalysts and increase their intrinsic activity in the oxygen reduction reaction (ORR). However, despite innumerable efforts having been carried out to explore this possibility, most of these achievements have focused on the rotating disk electrode (RDE) in half-cells, and relatively few results have been adaptable to membrane electrode assemblies (MEAs) in full-cells, which is the actual operating condition of fuel cells. Thus, it is uncertain whether these advanced catalysts can be used as a substitute in practical fuel cell applications, and an improvement in the catalytic performance in real-life fuel cells is still necessary. Therefore, from a more practical and industrial point of view, the goal of this review is to compare the ORR catalyst performance and durability in half- and full-cells, providing a differentiated approach to the durability concerns in half- and full-cells, and share new perspectives for strategic designs used to induce additional performance in full-cell devices.
Assuntos
Platina , Polímeros , Catálise , Eletrodos , Eletrólitos/química , Platina/química , Polímeros/químicaRESUMO
We develop a filtered absolute extreme ultraviolet (AXUV) diode array to measure the time evolution of the soft x-ray spectrum in the energy range of 1-10 keV. AXUV-HS5, the detector, has a fast rise time of 0.7 ns, a wide energy detection range, and high accessibility. We use Geant4 simulations to design an appropriate filter set for flat-and-sharp virtual channels (VCs), where a filter with no spectral edge removes large tails of the response curves. A Levenberg-Marquardt (LM) method, sensitive to the expected spectral function, is improved to reliably generate a continuous radiation spectrum, by utilizing spectral information from the least-squares (LS) method that reconstructs a discrete spectrum with low spectral resolution directly from the VCs. We test the filtered AXUV diode array on an X-pinch device with a peak current of 140 kA at Seoul National University; the array with ten channels is installed in a vacuum chamber. For a two-wire 40 µm stainless steel X-pinch, x-ray power, radiation temperature, and the reconstructed x-ray spectrum are obtained from the filtered AXUV diode array by the combined LS-LM method.
RESUMO
This paper describes an X-pinch device recently developed at Seoul National University (SNU). The SNU X-pinch device is designed and fabricated to accommodate various diagnostics as well as conduct versatile experiments. It is easy to change the capacitance of the pulse generator because the capacitor bank has a modular design without insulation oil or gas. This allows us to perform a variety of experiments with a wide capacitance range from 80 to 800 nF. The operating voltage of the SNU X-pinch device is controlled from 20 to 100 kV by adjusting the gas pressure inside a triggered spark-gap switch. Triggering of the spark-gap switch is synchronized with the operation of a pulsed laser to diagnose the X-pinch plasma at the proper time. A large vacuum chamber precisely machined from an aluminum mono-block is attached to the top of the pulse generator. It is designed to accommodate not only various X-pinch loads but also various diagnostic apparatus such as optical components. Initial experiments with the SNU X-pinch device have successfully generated x rays with wires of various materials and sizes. The device will be used not only to explore the dynamics of X-pinch plasmas but also as a test stand for diagnostics of high-energy-density plasmas.
RESUMO
Herein, thermoelectric carbon nanoparticle (CNP)-carbon nanotube (CNT) heterostructures are introduced as a promising flexible thermoelectric material. The optimal barrier energy between the CNP and CNT increases the Seebeck coefficient (S) of the heterostructures through the energy filtering effect. For optimized thermoelectric performance, the CNP-CNT barrier energy can be effectively tuned by controlling the work function of the CNPs. The optimized p-type CNP-CNT heterostructures exhibited S and power factor (PF) of 50.6 ± 1.4 µV K-1 and 400 ± 26 µW m-1 K-2, respectively. The n-type CNP-CNT heterostructures, optimized for another work function of the CNPs, exhibited S and PF of up to -37.5 ± 3.4 µV K-1 and 214 ± 42 µW m-1 K-2, respectively. The energy harvesting capability of a thermoelectric generator prepared using p- and n-type CNP-CNT heterostructures with optimized barrier energies is demonstrated. The thermoelectric generator with 10 p-type and 9 n-type thermoelectric elements exhibited a maximum output power of 0.12 µW from a ΔT of 5 K. This work shows a facile strategy for synthesizing thermoelectric CNP-CNT heterostructures with optimized energy filtering effects. Application to the thermoelectric device on a paper substrate is also discussed.
RESUMO
Fibroblast-derived extracellular matrix (fECM)-supported scaffolds made up of poly(lactic-co-glycolic acid) were prepared with the enhanced preservation of ECM components by composites with magnesium hydroxide nanoparticles (MH NPs), and were applied for the renal tissue regeneration. MH NP utilization resulted in an increased ECM protein amount, decreased scaffold degradation, and surface hydrophilic modification. These effects were correlated with the improved adhesion and viability of renal proximal tubule epithelial cells on the scaffold. In vivo experiments demonstrated effects of fECM and MH NPs on renal regeneration. The number of glomeruli was the largest in the ECM scaffold with MH NPs as compared to the pristine scaffold and ECM scaffold without MH NPs. Quantitative PCR analysis exhibited less inflammation (IL-1ß, TNF-α, and IL-6) and fibrosis-related (vimentin, collagen I, and α-SMA) markers, whereas opposite results were found in regeneration-related markers (Pax2, vWf, Wt1, and Emx2). The concentration of renal function-related molecules, creatinine and blood urea nitrogen diminished in the ECM scaffold with MH NPs. All results indicate that MH NPs utilization for the renal regenerative scaffold is effective for in vitro and in vivo environments and is, therefore, a good model for regeneration of kidneys and other tissues, and organs.
Assuntos
Nanopartículas , Alicerces Teciduais , Matriz Extracelular , Rim , Hidróxido de Magnésio , Engenharia TecidualRESUMO
In this study, shape-deformable thermoelectric p- and n-type doughs are fabricated by blending single-walled carbon nanotubes with excess amounts of nonvolatile liquid surfactants for efficient energy harvesting from diverse heat sources. The shape-deformable thermoelectric doughs exhibit touch-healing properties and can be easily molded into arbitrary shapes by simple shaping methods, such as those commonly used for rubber play dough. We used cube-shaped thermoelectric doughs to fabricate a vertical thermoelectric generator. Considering the shape-deformable properties of the thermoelectric doughs, a contraction strain of â¼2% in the through-plane direction of the thermoelectric generator can be applied for an effective application of ΔT. We show that the thermoelectric generator we built with eight p-n pairs exhibits a maximum output power of 2.2 µW at a vertical ΔT of 15 K. Our results demonstrate the energy harvesting capability of thermoelectric generators with shape-deformable p- and n-type doughs. Owing to the properties of this material, thermoelectric generators with various device geometries can be fabricated for energy harvesting from a diverse range of nonflat heat sources.
RESUMO
BACKGROUND: Inflammation induces dysfunction of endothelial cells via inflammatory cell adhesion, and this phenomenon and reactive oxygen species accumulation are pivotal triggers for atherosclerosis-related vascular disease. Although exosomes are excellent candidate as an inhibitor in the inflammation pathway, it is necessary to develop exosome-mimetic nanovesicles (NVs) due to limitations of extremely low release rate and difficult isolation of natural exosomes. NVs are produced in much larger quantities than natural exosomes, but due to the low flexibility of the cell membranes, the high loss caused by hanging on the filter membranes during extrusion remains a challenge to overcome. Therefore, by making cell membranes more flexible, more efficient production of NVs can be expected. METHODS: To increase the flexibility of the cell membranes, the suspension of umbilical cord-mesenchymal stem cells (UC-MSCs) was subjected to 5 freeze and thaw cycles (FT) before serial extrusion. After serial extrusion through membranes with three different pore sizes, FT/NVs were isolated using a tangential flow filtration (TFF) system. NVs or FT/NVs were pretreated to the human coronary artery endothelial cells (HCAECs), and then inflammation was induced using tumor necrosis factor-α (TNF-α). RESULTS: With the freeze and thaw process, the production yield of exosome-mimetic nanovesicles (FT/NVs) was about 3 times higher than the conventional production method. The FT/NVs have similar biological properties as NVs for attenuating TNF-α induced inflammation. CONCLUSION: We proposed the efficient protocol for the production of NVs with UC-MSCs using the combination of freeze and thaw process with a TFF system. The FT/NVs successfully attenuated the TNF-α induced inflammation in HCAECs.
Assuntos
Biomimética , Células Endoteliais/metabolismo , Exossomos/metabolismo , Inflamação/metabolismo , Células-Tronco Mesenquimais/citologia , Fator de Necrose Tumoral alfa/metabolismo , Cordão Umbilical/citologia , Aterosclerose/metabolismo , Adesão Celular , Citocinas , Humanos , Espécies Reativas de Oxigênio , Células THP-1RESUMO
Poly(l-lactic acid) (PLLA) is a biocompatible and biodegradable polymer that has received much attention as a biomedical material. However, PLLA also produces by-products that acidify the surrounding tissues during in vivo degradation, which induces inflammatory responses. To overcome these problems, magnesium hydroxide nanoparticles (nano-magnesium hydroxide; nMH) were added to the PLLA matrix as a bioactive filler that can suppress inflammatory responses by neutralizing the acidified environment caused by the degradation of PLLA. Despite the advantages of nMH, the strong cohesion of these nanoparticles toward each other makes it difficult to manufacture a polymer matrix containing homogeneous nanoparticles through thermal processing. Here, we prepared two types of surface-modified nMH with oligolactide (ODLLA) utilizing grafting to (GT) and grafting from (GF) strategies to improve the mechanical and biological characteristics of the organic-inorganic hybrid composite. The incorporation of surface-modified nMH not only enhanced mechanical properties, such as Young's modulus, but also improved homogeneity of magnesium hydroxide particles in the PLLA matrix due to the increase in interfacial interaction. Additionally, the PLLA composites with surface-modified nMH exhibited reduced bulk erosion during hydrolytic degradation with lower cytotoxicity and immunogenicity. Hemocompatibility tests on the PLLA composites with nMH showed a higher albumin to fibrinogen ratio (AFR) and a lower influence of platelet activation, when compared with unmodified control samples. Taken all together, the surface-modified nMH could be seen to successfully improve the physical and biological characteristics of polymer composites. We believe this technology has great potential for the development of hybrid nanocomposites for biomedical devices, including cardiovascular implants.
Assuntos
Dioxanos/química , Hidróxido de Magnésio/farmacologia , Poliésteres/química , Sobrevivência Celular/efeitos dos fármacos , Células Cultivadas , Módulo de Elasticidade , Células Endoteliais/citologia , Células Endoteliais/efeitos dos fármacos , Humanos , Concentração de Íons de Hidrogênio , Hidróxido de Magnésio/química , Teste de Materiais , Nanopartículas , Polímeros/química , Propriedades de SuperfícieRESUMO
Synthetic nanoparticles are extensively utilized in various biomedical engineering fields because of their unique physicochemical properties. However, their exogenous characteristics result in synthetic nanosystem invaders that easily induce the passive immune clearance mechanism, thereby increasing the retention effect caused by reticuloendothelial system (RES), resulting in low therapeutic efficacy and toxic effects. Recently, a cell membrane cloaking has been emerging technique as a novel interfacing approach from the biological/immunological perspective. This has been considered as useful technique for improving the performance of synthetic nanocarriers in vivo. By cell membrane cloaking, nanoparticles acquire the biological functions of natural cell membranes due to the presence of membrane-anchored proteins, antigens, and immunological moieties as well as physicochemical property of natural cell membrane. Due to cell membrane cloaking, the derived biological properties and functions of nanoparticles such as their immunosuppressive capability, long circulation time, and disease targeting ability have enhanced their future potential in biomedicine. Here, we review the cell membrane-cloaked nanosystems, highlight their novelty, introduce the preparation and characterization methods with relevant biomedical applications, and describe the prospects for using this novel biomimetic system that was developed from a combination of cell membranes and synthetic nanomaterials.
Assuntos
Aterosclerose/terapia , Membrana Celular/química , Sistemas de Liberação de Medicamentos/métodos , Isquemia/terapia , Nanopartículas/uso terapêutico , Neoplasias/terapia , Animais , Aterosclerose/metabolismo , Aterosclerose/patologia , Plaquetas/química , Plaquetas/metabolismo , Membrana Celular/metabolismo , Modelos Animais de Doenças , Eritrócitos/química , Eritrócitos/metabolismo , Humanos , Isquemia/metabolismo , Isquemia/patologia , Extração Líquido-Líquido/métodos , Camundongos , Mimetismo Molecular , Nanopartículas/química , Nanopartículas/metabolismo , Neoplasias/metabolismo , Neoplasias/patologia , Copolímero de Ácido Poliláctico e Ácido Poliglicólico/química , Sonicação/métodos , Células-Tronco/química , Células-Tronco/metabolismo , Linfócitos T/química , Linfócitos T/metabolismoRESUMO
The removal of heavy-metal ions from wastewater is an important objective from a public-health perspective, and chelating agents can be used to achieve this aim. Herein, we report the synthesis of mesoporous carbon as a chelating polymer host using nanoarchitectonics approach. Carboxymethylated polyethyleneimine, a chelating polymer, was incorporated into the mesopore walls of mesoporous carbon to create a polymer-mesoporous-carbon composite. Nitrogen adsorption- desorption experiments and scanning electron microscopy (SEM) were used to illustrate the structural advantages of the composite. Co2+ adsorption by the composite material was examined using cobalt nitrate solutions at pH 3. The study revealed that the Co2+-absorption data are most closely modeled by the Langmuir isotherm. The maximum adsorption capacity, calculated by linear regression, was determined to be about 40 mg-Co/g-composite at pH 3. The composite exhibited about a six-times higher adsorption capacity toward a dilute Co solution (12.5 ppm) than that of the pristine mesoporous carbon. In addition, the composite showed a substantially higher distribution coefficient (Kd = 1.54×105) compared to that (Kd = 2.05×10²) of the mesoporous carbon. Overall, we expect that the mesoporous composite, with its large mesopores (~20 nm), will be in high demand for adsorption applications.
RESUMO
Paclitaxel (Tx) is a widely used therapeutic chemical for breast cancer treatment; however, cancer recurrence remains an obstacle for improved prognosis of cancer patients. In this study, cold atmospheric plasma (CAP) was tested for its potential to overcome the drug resistance. After developing Tx-resistant MCF-7 (MCF-7/TxR) breast cancer cells, CAP was applied to the cells, and its effect on the recovery of drug sensitivity was assessed in both cellular and molecular aspects. Sensitivity to Tx in the MCF-7/TxR cells was restored up to 73% by CAP. A comparison of genome-wide expression profiles between the TxR cells and the CAP-treated cells identified 49 genes that commonly appeared with significant changes. Notably, 20 genes, such as KIF13B, GOLM1, and TLE4, showed opposite expression profiles. The protein expression levels of selected genes, DAGLA and CEACAM1, were recovered to those of their parental cells by CAP. Taken together, CAP inhibited the growth of MCF-7/TxR cancer cells and recovered Tx sensitivity by resetting the expression of multiple drug resistance-related genes. These findings may contribute to extending the application of CAP to the treatment of TxR cancer.
RESUMO
BACKGROUND: Ginsenoside Rg3, a derivative of steroidal saponins abundant in ginseng, has a range of effects on cancer cells, including anti-cell proliferation and anti-inflammation activity. Here, we investigate two long noncoding RNAs (lncRNAs), STXBP5-AS1 and RFX3-AS1, which are hypomethylated and hypermethylated in the promoter region by Rg3 in MCF-7 cancer cells. METHODS: The lncRNAs epigenetically regulated by Rg3 were mined using methylation array analysis. The effect of the lncRNAs on the apoptosis and proliferation of MCF-7 cells was monitored in the presence of Rg3 or Korean Red Ginseng (KRG) extract after deregulating the lncRNAs. The expression of the lncRNAs and their target genes was examined using qPCR and Western blot analysis. The association between the expression of the target genes and the survival rate of breast cancer patients was analyzed using the Kaplan-Meier Plotter platform. RESULTS: STXBP5-AS1 and RFX3-AS1 exhibited anti- and pro-proliferation effects, respectively, in the cancer cells, and the effects of Rg3 and KRG extract on apoptosis and cell proliferation were weakened after deregulating the lncRNAs. Of the genes located close to STXBP5-AS1 and RFX3-AS1 on the chromosome, STXBP5, GRM1, RFX3, and SLC1A1 were regulated by the lncRNAs on the RNA and protein level. Breast cancer patients that exhibited a higher expression of the target genes of the lncRNAs had a higher metastasis-free survival rate. CONCLUSION: The current study is the first to identify lncRNAs that are regulated by the presence of Rg3 and KRG extract and that subsequently contribute to inhibiting the proliferation of cancer cells.
RESUMO
Ginsenoside Rh2, a major bioactive ingredient abundant in red ginseng, has an antiproliferative effect on various cancer cells. In this study, we report a novel long noncoding RNA, C3orf67-AS1, which was identified as being hypermethylated at a CpG site of the promoter by Rh2 in MCF-7 cancer cells. Rh2-induced hypermethylation was responsible for the lower gene expression; the expression was recovered following treatment with a methyltransferase inhibitor, 5-aza-2'-deoxycytidine. When C3orf67-AS1 was downregulated by a siRNA, the cell growth rate was decreased, demonstrating the RNA's oncogenic activity. Accordingly, breast cancer patients showed a lower methylation and higher expression level of C3orf67-AS1. Within 800 kb flanking C3orf67-AS1 on the chromosome, eight genes were found, and four genes including C3orf67 (the sense strand gene of C3orf67-AS1) were downregulated by Rh2. In particular, C3orf67 was downregulated when C3orf67-AS1 was suppressed by a siRNA; however, the expression of C3orf67-AS1 was not affected by C3orf67. Taken together, this study identifies a novel noncoding RNA, C3orf67-AS1, of which the expression could be suppressed by Rh2 via promoter methylation, thereby mediating the anti-proliferative effect of the ginsenoside.
Assuntos
Neoplasias da Mama/genética , Proliferação de Células/efeitos dos fármacos , Ginsenosídeos/farmacologia , RNA Longo não Codificante/genética , Neoplasias da Mama/tratamento farmacológico , Neoplasias da Mama/metabolismo , Neoplasias da Mama/fisiopatologia , Linhagem Celular Tumoral , Metilação de DNA , Epigênese Genética/efeitos dos fármacos , Feminino , Regulação Neoplásica da Expressão Gênica/efeitos dos fármacos , Humanos , Células MCF-7 , Regiões Promotoras Genéticas , RNA Longo não Codificante/metabolismoRESUMO
Composite metal-organic frameworks (MOFs) tend to possess complex interfaces that prevent facile and rational design. Here we present a joint computational/experimental workflow that screens thousands of MOFs and identifies the optimal MOF pairs that can seamlessly connect to one another by taking advantage of the fact that the metal nodes of one MOF can form coordination bonds with the linkers of the second MOF. Six MOF pairs (HKUST-1@MOF-5, HKUST-1@IRMOF-18, UiO-67@HKUST-1, PCN-68@MOF-5, UiO-66@MIL-88B(Fe) and UiO-67@MIL-88C(Fe)) yielded from our theoretical predictions were successfully synthesized, leading to clean single crystalline MOF@MOF, demonstrating the power of our joint workflow. Our work can serve as a starting point to accelerate the discovery of novel MOF composites that can potentially be used for many different applications.
RESUMO
The optoelectronic properties of quasi-two-dimensional organic-inorganic hybrid perovskites can be tuned by controlling the formation of Ruddlesden-Popper type phases, which enables diverse device applications such as photovoltaics and light-emitting diodes (LEDs). Herein, the influence of excess organic cations on the phase formation of (PEA)2MAn-1PbnBr3n+1 is systematically investigated with various mixing ratios to discover the phase distribution beneficial for light-emitting diodes. It is found that PEA cations exceeding Pb ions in molar ratio are required to produce small-n phases in the films with a strong photoluminescence, while excess MA cations enable the formation of more large-n phases. Low electrical conductivity inherent to the properties of quasi-2D perovskites is further lowered by the introduction of excess organic cations. This is overcome by the intercalation of zinc oxide (ZnO) nanoparticles (NPs) into the blocking layers composed of PEA cations. Importantly, these metal oxide NPs also modulate the phase distribution, enabling the realization of bright green quasi-2D perovskites with a better stability and a maximum luminance of nearly 60 000 cd m-2, which is the highest brightness compared to the so far reported quasi-2D perovskite LEDs incorporating organic cations.