Integrated atomic layer deposition and chemical vapor reaction for the preparation of metal organic framework coatings for solid-phase microextraction Arrow.

New chemical vapor reaction (CVR) and atomic layer deposition (ALD)-conversion methods were utilized for preparation of metal organic frameworks (MOFs) coatings of solid phase microextraction (SPME) Arrow for the first time. With simple, easy and convenient one-step reaction or conversion, four MOF coatings were made by suspend ALD iron oxide (Fe2O3) film or aluminum oxide (Al2O3) film above terephthalic acid (H2BDC) or trimesic acid (H3BTC) vapor. UIO-66 coating was made by zirconium (Zr)-BDC film in acetic acid vapor. As the first documented instance of all-gas phase synthesis of SPME Arrow coatings, preparation parameters including CVR/conversion time and temperature, acetic acid volume, and metal oxide film/metal-ligand films thickness were investigated. The optimal coatings exhibited crystalline structures, excellent uniformity, satisfactory thickness (2-7.5 µm), and high robustness (>80 times usage). To study the practical usefulness of the coatings for the extraction, several analytes with different chemical properties were tested. The Fe-BDC coating was found to be the most selective and sensitive for the determination of benzene ring contained compounds due to its highly hydrophobic surface and unsaturated metal site. UIO-66 coating was best for small polar, aromatic, and long chain polar compounds owing to its high porosity. The usefulness of new coatings were evaluated for gas chromatography-mass spectrometer (GC-MS) determination of several analytes, present in wastewater samples at three levels of concentration, and satisfactory results were achieved.

Chemical Characterization of Gas- and Particle-Phase Products from the Ozonolysis of α-Pinene in the Presence of Dimethylamine.

Amines are recognized as key compounds in new particle formation (NPF) and secondary organic aerosol (SOA) formation. In addition, ozonolysis of α-pinene contributes substantially to the formation of biogenic SOAs in the atmosphere. In the present study, ozonolysis of α-pinene in the presence of dimethylamine (DMA) was investigated in a flow tube reactor. Effects of amines on SOA formation and chemical composition were examined. Enhancement of NPF and SOA formation was observed in the presence of DMA. Chemical characterization of gas- and particle-phase products by high-resolution mass spectrometric techniques revealed the formation of nitrogen containing compounds. Reactions between ozonolysis reaction products of α-pinene, such as pinonaldehyde or pinonic acid, and DMA were observed. Possible reaction pathways are suggested for the formation of the reaction products. Some of the compounds identified in the laboratory study were also observed in aerosol samples (PM1) collected at the SMEAR II station (Hyytiälä, Finland) suggesting that DMA might affect the ozonolysis of α-pinene in ambient conditions.

Modified zeolitic imidazolate framework-8 as solid-phase microextraction Arrow coating for sampling of amines in wastewater and food samples followed by gas chromatography-mass spectrometry.

In this study, a novel solid phase microextration (SPME) Arrow was prepared for the sampling of volatile low molecular weight alkylamines (trimethylamine (TMA) and triethylamine (TEA)) in wastewater, salmon and mushroom samples before gas chromatographic separation with mass spectrometer as detector. Acidified zeolitic imidazolate framework-8 (A-ZIF-8) was utilized as adsorbent and poly(vinyl chloride) (PVC) as the adhesive. The custom SPME Arrow was fabricated via a physical adhesion: (1) ZIF-8 particles were suspended in a mixture of tetrahydrofuran (THF) and PVC to form a homogeneous suspension, (2) a non-coated stainless steel SPME Arrow was dipped in the ZIF-8/PVC suspension for several times to obtain a uniform and thick coating, (3) the pore size of ZIF-8 was modified by headspace exposure to hydrochloric acid in order to increase the extraction efficiency for amines. The effect of ZIF-8 concentration in PVC solution, dipping cycles and aging temperature on extraction efficiency was investigated. In addition, sampling parameters such as NaCl concentration, sample volume, extraction time, potassium hydroxide concentration, desorption temperature and desorption time were optimized. The Arrow-to-Arrow reproducibilities (RSDs) for five ZIF-8 coated Arrows were 15.6% and 13.3% for TMA and TEA, respectively. The extraction with A-ZIF-8/PVC Arrow was highly reproducible for at least 130 cycles without noticeable decrease of performance (RSD<12.5%). Headspace SPME of 7.5mL sample solution with the fabricated ZIF-8 coated Arrow achieved linear ranges of 1-200ngmL-1 for both TMA and TEA. The limit of quantitation (LOQ) was 1ngmL-1 for both TMA and TEA. The method was successfully applied to the determination of TMA and TEA in wastewater, salmon and mushroom samples giving satisfactory selectivity towards the studied amines.

Nontargeted evaluation of the fate of steroids during wastewater treatment by comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry.

Emerging organic contaminants in wastewater are usually analyzed by targeted approaches, and especially estrogens have been the focus of environmental research due to their high hormonal activity. The selection of specific target compounds means, however, that most of the sample components, including transformation products and potential new contaminants, are neglected. In this study, the fate of steroidal compounds in wastewater treatment processes was evaluated by a nontargeted approach based on comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry. The potential of the nontargeted approach to generate comprehensive information about sample constituents was demonstrated with use of statistical tools. Transformation pathways of the tentatively identified compounds with steroidal four-ring structure were proposed. The purification efficiency of the wastewater treatment plants was studied, and the distribution of the compounds of interest in the suspended solids, effluent water, and sludge was measured. The results showed that, owing to strong adsorption of hydrophobic compounds onto the solid matter, the steroids were mostly bound to the suspended solids of the effluent water and the sewage sludge at the end of the treatment process. The most abundant steroid class was androstanes in the aqueous phase and cholestanes in the solid phase. 17ß-estradiol was the most abundant estrogen in the aqueous phase, but it was only detected in the influent samples indicating efficient removal during the treatment process. In the sludge samples, however, high concentrations of an oxidation product of 17ß-estradiol, estrone, were measured.

Nitrogen-Containing Low Volatile Compounds from Pinonaldehyde-Dimethylamine Reaction in the Atmosphere: A Laboratory and Field Study.

Pinonaldehyde, which is among the most abundant oxidation products of α-pinene, and dimethylamine were selected to study the formation of N-containing low volatile compounds from aldehyde-amine reactions in the atmosphere. Gas phase reactions took place in a Tedlar bag, which was connected to a mass spectrometer ionization source via a short deactivated fused silica column. In addition to on-line analysis, abundance of gaseous precursors and reaction products were monitored off-line. Condensable products were extracted from the bag's walls with a suitable solvent and analyzed by gas chromatography coupled to chemical ionization high-resolution quadrupole time-of-flight mass spectrometry and by ultra-high-performance liquid chromatography coupled to electrospray ionization Orbitrap mass spectrometry. The reactions carried out resulted in several mid-low vapor pressure nitrogen-containing compounds that are potentially important for the formation of secondary organic aerosols in the atmosphere. Further, the presence of brown carbon, confirmed by liquid chromatography-UV-vis-mass spectrometry, was observed. Some of the compounds identified in the laboratory study were also observed in aerosol samples collected at SMEAR II station (Hyytiälä, Finland) in August 2015 suggesting the importance of aldehyde-amine reactions for the aerosol formation and growth.

Development of spoilage bacterial community and volatile compounds in chilled beef under vacuum or high oxygen atmospheres.

Research into microbial community development and metabolism is essential to understand meat spoilage. Recent years have seen the emergence of powerful molecular techniques that are being used alongside conventional microbiology approaches. This enables more accurate studies on meat spoilage. The aim of this study was to investigate the influence of packaging (under vacuum and in high oxygen atmosphere) on the development of microbial communities and metabolic activities at 6 °C by using culture-dependent (cultivation, ribotyping) and culture-independent (amplicon sequencing) methods. At the beginning of shelf life, the microbial community mostly consisted of Carnobacterium and Lactobacillus. After two weeks of storage, Lactococcus and Lactobacillus were the dominant genera under vacuum and Leuconostoc in high oxygen meat packages. This indicates that oxygen favoured the genus Leuconostoc comprising only heterofermentative species and hence potential producers of undesirable compounds. Also the number of volatile compounds, such as diacetyl, 1-octen-3-ol and hexanoic acids, was higher in high oxygen packages than under vacuum packages. The beef in high oxygen atmosphere packaging was detected as spoiled in sensory evaluation over 10 days earlier than beef under vacuum packaging. Leuconostoc gelidum, Lactococcus piscium, Lactobacillus sakei and Lactobacillus algidus were the most common species of bacteria. The results obtained from identification of the isolates using ribotyping and amplicon sequencing correlated, except for L. algidus, which was detected in both types of packaging by amplicon sequencing, but only in vacuum packaged samples using the culture-based technique. This indicates that L. algidus grew, but was not cultivable in high oxygen beef using the Nordic Committee on Food Analysis standard method.

Solid phase microextraction Arrow for the sampling of volatile amines in wastewater and atmosphere.

A new method is introduced for the sampling of volatile low molecular weight alkylamines in ambient air and wastewater by utilizing a novel SPME Arrow system, which contains a larger volume of sorbent compared to a standard SPME fiber. Parameters affecting the extraction, such as coating material, need for preconcentration, sample volume, pH, stirring rate, salt addition, extraction time and temperature were carefully optimized. In addition, analysis conditions, including desorption temperature and time as well as gas chromatographic parameters, were optimized. Compared to conventional SPME fiber, the SPME Arrow had better robustness and sensitivity. Average intermediate reproducibility of the method expressed as relative standard deviation was 12% for dimethylamine and 14% for trimethylamine, and their limit of quantification 10µg/L and 0.13µg/L respectively. Working range was from limits of quantification to 500µg/L for dimethylamine and to 130µg/L for trimethylamine. Several alkylamines were qualitatively analyzed in real samples, while target compounds dimethyl- and trimethylamines were quantified. The concentrations in influent and effluent wastewater samples were almost the same (∼80µg/L for dimethylamine, 120µg/L for trimethylamine) meaning that amines pass the water purification process unchanged or they are produced at the same rate as they are removed. For the air samples, preconcentration with phosphoric acid coated denuder was required and the concentration of trimethylamine was found to be around 1ng/m(3). The developed method was compared with optimized method based on conventional SPME and advantages and disadvantages of both approaches are discussed.

Desorption atmospheric pressure photoionization high-resolution mass spectrometry: a complementary approach for the chemical analysis of atmospheric aerosols.

RATIONALE: On-line chemical characterization methods of atmospheric aerosols are essential to increase our understanding of physicochemical processes in the atmosphere, and to study biosphere-atmosphere interactions. Several techniques, including aerosol mass spectrometry, are nowadays available, but they all suffer from some disadvantages. In this research, desorption atmospheric pressure photoionization high-resolution (Orbitrap) mass spectrometry (DAPPI-HRMS) is introduced as a complementary technique for the fast analysis of aerosol chemical composition without the need for sample preparation. METHODS: Atmospheric aerosols from city air were collected on a filter, desorbed in a DAPPI source with a hot stream of toluene and nitrogen, and ionized using a vacuum ultraviolet lamp at atmospheric pressure. To study the applicability of the technique for ambient aerosol analysis, several samples were collected onto filters and analyzed, with the focus being on selected organic acids. To compare the DAPPI-HRMS data with results obtained by an established method, each filter sample was divided into two equal parts, and the second half of the filter was extracted and analyzed by liquid chromatography/mass spectrometry (LC/MS). RESULTS: The DAPPI results agreed with the measured aerosol particle number. In addition to the targeted acids, the LC/MS and DAPPI-HRMS methods were found to detect different compounds, thus providing complementary information about the aerosol samples. CONCLUSIONS: DAPPI-HRMS showed several important oxidation products of terpenes, and numerous compounds were tentatively identified. Thanks to the soft ionization, high mass resolution, fast analysis, simplicity and on-line applicability, the proposed methodology has high potential in the field of atmospheric research.

Methods for characterization of organic compounds in atmospheric aerosol particles.

Atmospheric aerosol particles of primary or secondary, biogenic or anthropogenic origin are highly complex samples of changing composition in time and space. To assess their effects on climate or human health, the size-dependent chemical composition of these ubiquitous atmospheric constituents must be known. The development of novel analytical methods has enabled more detailed characterization of the organic composition of aerosols. This review gives an overview of the methods used in the chemical characterization of atmospheric aerosol particles, with a focus on mass-spectrometry techniques for organic compounds, either alone or in combination with chromatographic separation. Off-line, on-site, and on-line methods are covered, and the advantages and limitations of the different methods are discussed. The main emphasis is on methods used for detailed characterization of the composition of the organic compounds in aerosol particles. We address and summarize the current state of analytical methods used in aerosol research and discuss the importance of developing novel sampling strategies and analytical instrumentation. Graphical Abstract Challenges in the atmospheric aerosol analytics.

Determination of atmospheric amines by on-fiber derivatization solid-phase microextraction with 2,3,4,5,6-pentafluorobenzyl chloroformate and 9-fluorenylmethoxycarbonyl chloride.

Alkylamines play an important role in atmospheric chemistry and are of concern for human health. Determining them from the vapor phase is challenging owing to their high polarity and volatility, water solubility, low concentrations, and poor chromatographic properties. We propose on-fiber derivatization solid-phase microextraction (SPME) to increase sensitivity and selectivity for the determination of alkylamines in air samples. SPME fibers coated in head-space with 2,3,4,5,6-pentafluorobenzyl chloroformate (PFBCF, 10min) or 9-fluorenylmethoxycarbonyl (FMOC) chloride (5min) were exposed to the sample for 5-120min, after which the derivatized alkylamines were thermally desorbed in the GC injection port and analyzed by GC-MS. The specific focus of the research was dimethylamine (DMA) but, as well as secondary amines, both coating agents readily react with primary and tertiary amines and with ammonia at ambient temperatures. The fiber coating procedures, sampling times, and analytical conditions were optimized, and methods were tested with natural samples. PFBCF was more selective and almost an order of magnitude more sensitive than FMOC chloride. Both reagents are applicable, however, depending on the requirements. With scan mode and use of molecular ion for quantification, the limit of quantification for DMA was 0.17µgL(-1) when derivatized with PFBCF and 3.4µgL(-1) when derivatized with FMOC chloride. When selected ion monitoring was used with the most abundant ion, the limit of quantification for DMA was 2.8ngL(-1). Intermediate reproducibility expressed as relative standard deviation was around 30% with PFBCF and less than 20% with FMOC chloride. Fibers coated with PFBCF could be used at least up to 24h when stored at 4°C and for 5 to 7h when stored at room temperature. After sampling/derivatization, storage time before analysis should not exceed 48h at 4°C or 24h at room temperature. At maximum, the PFBCF-coated fiber can be used in 100 coating/sampling/analysis cycles.

Production of buttery-odor compounds and transcriptome response in Leuconostoc gelidum subsp. gasicomitatum LMG18811T during growth on various carbon sources.

Leuconostoc gelidum subsp. gasicomitatum is a common spoilage bacterium in meat products packaged under oxygen-containing modified atmospheres. Buttery off-odors related to diacetyl/acetoin formation are frequently associated with the spoilage of these products. A whole-genome microarray study, together with gas chromatography (GC)-mass spectrometry (MS) analyses of the pathway end products, was performed to investigate the transcriptome response of L. gelidum subsp. gasicomitatum LMG18811(T) growing on semidefined media containing glucose, ribose, or inosine, which are essential carbon sources in meat. Generally, the gene expression patterns with ribose and inosine were quite similar, indicating that catabolism of ribose and nucleosides is closely linked. Diacetyl/acetoin concentrations as high as 110 or 470 µM were measured when growth was based on inosine or ribose, respectively. The gene expression results for pyruvate metabolism (upregulation of α-acetolactate synthase, downregulation of l-lactate dehydrogenase and pyruvate dehydrogenase) were as expected when diacetyl and acetoin were the end products. No diacetyl production (<7.5 µM) was detected with the glucose-containing medium, even though the cell counts of LMG18811(T) was 6 or 10 times higher than that on inosine or ribose, respectively. Although glucose was the most effective carbon source for the growth of L. gelidum subsp. gasicomitatum, utilization of inosine and ribose resulted in the production of the unwanted buttery-odor compounds. These results increase our understanding of which compounds are likely to enhance the formation of buttery odors during meat spoilage caused by L. gelidum subsp. gasicomitatum.

The Effect of Ambient Ozone on Unsaturated Tear Film Wax Esters.

PURPOSE: Tear film lipid layer (TFLL) is constantly exposed to reactive ozone in the surrounding air, which may have detrimental effects on ocular health. Behenyl oleate (BO), a representative tear film wax ester, was used to study the reaction with ozone at the air-water interface. METHODS: Time-dependent changes in mean molecular area of BO monolayers were measured at different ozone concentrations and surface pressures. In addition, the effect of ascorbic acid on the reaction rate was determined. Reaction was followed using thin-layer chromatography and reaction products were identified using liquid chromatography-electrospray ionization mass spectrometry (LC-MS). Tear fluid samples from healthy subjects were analyzed with LC-MS for any ozonolysis reaction products. RESULTS: Behenyl oleate was found to undergo rapid ozonolysis at the air-water interface at normal indoor ozone concentrations. The reaction was observed as an initial expansion followed by a contraction of the film area. Ascorbic acid was found to decrease the rate of ozonolysis. Main reaction products were identified as behenyl 9-oxononanoate and behenyl 8-(5-octyl-1,2,4-trioxolan-3-yl)octanoate. Similar ozonolysis products were not detected in the tear fluid samples. CONCLUSIONS: At the air-water interface, unsaturated wax esters react readily with ozone in ambient air. However, no signs of ozonolysis products were found in the tear fluid. This is most likely due to the antioxidant systems present in tear fluid. Last, the results show that ozonolysis needs to be controlled in future surface chemistry studies on tear film lipids.

A new approach to determine vapor pressures of compounds in multicomponent systems by comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry.

A method is described to determine vapor pressures of compounds in multicomponent systems simultaneously. The method is based on temperature-gradient analysis by comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GCxGC-TOFMS). Vapor pressures are determined with the aid of known vapor pressure values of reference compounds eluting before and after the analytes. Reference compounds with the same functionalities as the analytes are preferred, but when these are not available, the alkane series can be utilized. The number of compounds whose vapor pressures can be determined is limited only by the peak capacity of the chromatographic system. Although the lowest subcooled vapor pressure determined was 0.006 Pa, for tetrahydroaraucarolone in an atmospheric aerosol sample, vapor pressures as low as 10(-6) Pa can be measured with the described set-up. Even lower values can be measured with higher GC temperatures and longer analysis times. Since only a few picograms of compound is required, in a mixture of any complexity, the GCxGC-TOFMS method offers unique sensitivity, rapidity, and comprehensiveness.

Quaternary ammonium-functionalized silica sorbents for the solid-phase extraction of aromatic amines under normal phase conditions.

Quaternary ammonium-functionalized silica materials were synthesized and applied for solid-phase extraction (SPE) of aromatic amines, which are classified as priority pollutants by US Environmental Protection Agency. Hexamethylenetetramine used for silica surface modification for the first time was employed as SPE sorbent under normal phase conditions. Hexaminium-functionalized silica demonstrated excellent extraction efficiencies for o-toluidine, 4-ethylaniline and quinoline (recoveries 101-107%), while for N,N-dimethylaniline and N-isopropylaniline recoveries were from low to moderate (14-46%). In addition, the suitability of 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica as SPE sorbent was tested under normal phase conditions. The recoveries achieved for the five aromatic amines ranged from 89 to 99%. The stability of the sorbent was evaluated during and after 150 extractions. Coefficients of variation between 4.5 and 10.2% proved a high stability of the synthesized sorbent. Elution was carried out using acetonitrile in the case of hexaminium-functionalized silica and water for 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent. After the extraction the analytes were separated and detected by liquid chromatography ultraviolet detection (LC-UV). The retention mechanism of the materials was primarily based on polar hydrogen bonding and π-π interactions. Comparison made with activated silica proved the quaternary ammonium-functionalized materials to offer different selectivity and better extraction efficiencies for aromatic amines. Finally, 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent was successfully tested for the extraction of wastewater and soil samples.

Liquid chromatography-dopant-assisted atmospheric pressure photoionization-mass spectrometry: Application to the analysis of aldehydes in atmospheric aerosol particles.

A complete methodology based on LC-anisole-toluene dopant-assisted atmospheric pressure photoionization-IT-MS was developed for the determination of aldehydes in atmospheric aerosol particles. For the derivatization, ultrasound was used to accelerate the reaction between the target analytes and 2,4-dinitrophenylhydrazine. The developed methodology was validated for three different samples, gas phase, ultrafine (Dp = 30 ± 4 nm; where Dp stands for particle diameter) and all-sized particles, collected on Teflon filters. The method quantitation limits ranged from 5 to 227 pg. The accuracy and the potential matrix effects were evaluated using standard addition methodology. Recoveries ranged between 91.7 and 109.9%, and the repeatability and the reproducibility of the method developed between 0.5 and 8.0% and between 2.9 and 11.1%, respectively. The results obtained by the developed methodology compared to those provided by the previously validated method revealed no statistical differences. The method developed was applied to the determination of aldehydes in 16 atmospheric aerosol samples (30 nm and all-sized samples) collected at the Station for Measuring Forest Ecosystem-Atmosphere Relations II during spring 2011. The mean concentrations of aldehydes, and oxidation products of terpenes were between 0.05 and 82.70 ng/m(3).

Aliphatic and aromatic amines in atmospheric aerosol particles: comparison of three ionization techniques in liquid chromatography-mass spectrometry and method development.

A complete methodology was developed for the determination of ten aliphatic and nine aromatic amines in atmospheric aerosol particles. Before the liquid chromatography - tandem mass spectrometric separation and determination, the derivatization reaction of the analytes using dansyl chloride was accelerated by ultrasounds. From three different ionization techniques studied electrospray ionization was superior in terms of sensitivity, linearity, repeatability and reproducibility over atmospheric pressure chemical ionization and photoionization for the target analytes. The method developed was validated for the gas phase, 30 nm and total suspended atmospheric aerosol particles. The method quantification limits ranged between 1.8 and 71.7 pg. The accuracy and the potential matrix effects were evaluated using a standard addition methodology. Recoveries from 92.1% to 109.1%, the repeatability from 0.6% to 8.4% and the reproducibility from 2.3% to 9.8% were obtained. The reliability of the methodology was proved by the statistical evaluation. Finally, the developed methodology was applied to the determination of the target analytes in eight size separated ultrafine particulate (Dp=30±4 nm) samples and in eight total suspended particulate samples collected at the SMEAR II station. The mean concentrations for aliphatic amines were between 0.01 and 42.67 ng m(-3) and for aromatic amines between 0.02 and 1.70 ng m(-3). Thirteen amines were quantified for the first time in 30 nm aerosol particles.

Ionic liquid-functionalized silica for selective solid-phase extraction of organic acids, amines and aldehydes.

Three ionic liquid (IL)-functionalized silica materials, imidazolium, N-methylimidazolium and 1-alkyl-3-(propyl-3-sulfonate) imidazolium, were synthesised and applied in solid-phase extraction (SPE) of organic acids, amines and aldehydes, which are important compound families in atmospheric aerosol particles. 1-Alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica was tested as sorbent for SPE for the first time. The analytes were separated and detected by liquid chromatography-mass spectrometry (LC-MS). To confirm the results achieved by LC-MS, the acids were additionally determined by gas chromatography-mass spectrometry (GC-MS). The stability of the IL-functionalized silica materials was tested at low and high pH. The effect of the pH on the extraction was also informative of the retention mechanism of the materials. The results showed anion exchange to be the main interaction, but hydrophobic and π interactions and hydrogen bonding also played a role in the extraction. Extraction efficiencies for organic acids ranged from 87 to 110%, except for cis-pinonic acid (19-29%). Lower extraction efficiencies for amines and aldehydes confirmed that anionic exchange was the predominant interaction. Comparisons made with two commercial SPE materials--silica-based strong anion exchange (SAX) and polymer-based mixed-mode anion exchange and reverse-phase (MAX)--showed the IL-functionalized materials to offer different selectivity and better extraction efficiency than SAX for aromatic compounds. Finally, the new materials were successfully tested in the extraction of an atmospheric aerosol sample.

Comprehensive two-dimensional gas chromatography, a valuable technique for screening and semiquantitation of different chemical compounds in ultrafine 30 nm and 50 nm aerosol particles.

Comprehensive two dimensional gas chromatography-time-of-flight mass spectrometry (GC×GC-TOF-MS) was used for screening and semiquantitation of semivolatile organic compounds in aerosol particles. As the volatility was a prerequisite parameter for the analysis, some compounds were transformed via derivatization such as silylation into more volatile ones. The identification of the analytes was made by comparing the GC retention indices and the TOF mass spectra with the NIST and the Golm metabolome database reference libraries. The data treatment was simplified by exploiting an additional classification of the identified compounds, namely the main functional group or specific element present in the molecule leading to different groups of compounds. This methodology was applied to identify compounds in 30 ± 4 nm, 50 ± 5 nm and total suspended particles (TSP) collected during spring and autumn of 2009 and summer of 2010 at the Station for Measuring Forest Ecosystem Atmosphere Relations (SMEAR II) at Hyytiälä (Finland). The number of identified compounds was higher than 400, which were the most relevant compounds present in the samples, in terms of concentrations. The analysis of aerosol particles of different sizes, collected simultaneously, revealed that the number of compounds increased with the particle size whereas the normalized response factor decreased in most of the cases, aldehydes being an exception. This decrease could be associated with the formation or aggregation of new compounds onto the particles when they grow in the atmosphere.

Comparison of quartz and Teflon filters for simultaneous collection of size-separated ultrafine aerosol particles and gas-phase zero samples.

In this research, the two most common filter media, quartz and Teflon, were tested to obtain information about the possible adsorption of gas-phase compounds onto filters during long sample collection of atmospheric aerosols. Particles of nanometer-size for off-line chemical characterization were collected using a recently introduced differential mobility analyzer for size separation. Samples were collected at an urban site (Helsinki, SMEARIII station) during spring 2010. Sampling time was 4 to 10 days for particles 50, 40, or 30 nm in diameter. Sample air flow was 4 L/min. The sampling setup was arranged so that two samples were obtained for each sampling period almost simultaneously: one containing particles and adsorbed gas-phase compounds and one containing adsorbed gas-phase compounds only. Filters were extracted and analyzed for the presence of selected carboxylic acids, polyols, nitrogen-containing compounds, and aldehydes. The results showed that, in quartz filter samples, gas-phase adsorption may be responsible for as much as 100% of some compound masses. Whether quartz or Teflon, simultaneous collection of gas-phase zero samples is essential during the whole sampling period. The dependence of the adsorption of gas-phase compounds on vapor pressure and the effect of adsorption on the deposited aerosol layer are discussed.