Enhancing Thermal Stability of Perovskite Solar Cells through Thermal Transition and Thin Film Crystallization Engineering of Polymeric Hole Transport Layers.

Organic hole transport layers (HTLs) have been known to be susceptible to thermal stress, leading to poor long-term stability in perovskite solar cells (PSCs). We synthesized three 2,5-dialkoxy-substituted, 1,4-bis(2-thienyl)phenylene (TPT)-based conjugated polymers (CPs) linked with thiophene-based (thiophene (T) and thienothiophene (TT)) comonomers and evaluated them as HTLs in n-i-p PSCs. TPT-T (MB/C6), which has branched 2-methylbutyl and linear hexyl (MB/C6) side chains, emerged as a promising HTL candidate, enabling power conversion efficiencies (PCEs) greater than 15%. In addition, PSCs with this HTL showed an improvement in long-term stability at elevated temperatures of 65 °C when compared to those with the state-of-art HTL, 2,2',7,7'-tetrakis(N,N-p-dimethoxyphenylamino)-9,9'-spirobifluorene (spiro-OMeTAD). This improvement is ascribed to the lack of thermal transitions within the operational temperature range of PSCs for TPT-T (MB/C6), which is attributed to the relatively short branched side chains of this polymer. We propose that the elimination of thermal transitions below 200 °C leads to HTLs without cracking as-deposited and after conducting a stress test at 65 °C, which can serve as a new design guideline for HTL development.

Nanometer Control of Ruddlesden-Popper Interlayers by Thermal Evaporation for Efficient Perovskite Photovoltaics.

Solution-processed Ruddlesden-Popper (RP) interlayers in lead halide perovskite solar cells (PSCs) present processing challenges due to fast film formation and uncontrolled growth of phases and layer thickness at interfaces. In this work, an alternative, solvent-free, thermal co-evaporation process is developed to deposit RP interlayers. The method provides precise control on interlayer thickness and enables understanding its role on charge-carrier extraction. Studying RP film growth reveals the development of heterointerfaces when deposited on three-dimensional (3D) perovskite layers. This allows a large thickness window with an optimum between 20 nm and 40 nm to improve the optoelectronic properties of the underlying 3D perovskite. Solar cells using evaporated interlayers achieve power conversion efficiency of 21.6%, compared to 19.6% for untreated devices, driven by improvements in the open-circuit voltage and fill factor. This work sheds light on the importance of phase and thickness control of passivation layers, which ultimately determine the solar cell performance in state-of-the-art PSCs.

Tailoring Interface Energies via Phosphonic Acids to Grow and Stabilize Cubic FAPbI3 Deposited by Thermal Evaporation.

Coevaporation of formamidinium lead iodide (FAPbI3) is a promising route for the fabrication of highly efficient and scalable optoelectronic devices, such as perovskite solar cells. However, it poses experimental challenges in achieving stoichiometric FAPbI3 films with a cubic structure (α-FAPbI3). In this work, we show that undesired hexagonal phases of both PbI2 and FAPbI3 form during thermal evaporation, including the well-known 2H-FAPbI3, which are detrimental for optoelectronic performance. We demonstrate the growth of α-FAPbI3 at room temperature via thermal evaporation by depositing phosphonic acids (PAc) on substrates and subsequently coevaporating PbI2 and formamidinium iodide. We use density-functional theory to develop a theoretical model to understand the relative growth energetics of the α and 2H phases of FAPbI3 for different molecular interactions. Experiments and theory show that the presence of PAc molecules stabilizes the formation of α-FAPbI3 in thin films when excess molecules are available to migrate during growth. This migration of molecules facilitates the continued presence of adsorbed organic precursors at the free surface throughout the evaporation, which lowers the growth energy of the α-FAPbI3 phase. Our theoretical analyses of PAc molecule-molecule interactions show that ligands can form hydrogen bonding to reduce the migration rate of the molecules through the deposited film, limiting the effects on the crystal structure stabilization. Our results also show that the phase stabilization with molecules that migrate is long-lasting and resistant to moist air. These findings enable reliable formation and processing of α-FAPbI3 films via vapor deposition.

Bromine Incorporation Affects Phase Transformations and Thermal Stability of Lead Halide Perovskites.

Mixed-cation and mixed-halide lead halide perovskites show great potential for their application in photovoltaics. Many of the high-performance compositions are made of cesium, formamidinium, lead, iodine, and bromine. However, incorporating bromine in iodine-rich compositions and its effects on the thermal stability of the perovskite structure has not been thoroughly studied. In this work, we study how replacing iodine with bromine in the state-of-the-art Cs0.17FA0.83PbI3 perovskite composition leads to different dynamics in the phase transformations as a function of temperature. Through a combination of structural characterization, cathodoluminescence mapping, X-ray photoelectron spectroscopy, and first-principles calculations, we reveal that the incorporation of bromine reduces the thermodynamic phase stability of the films and shifts the products of phase transformations. Our results suggest that bromine-driven vacancy formation during high temperature exposure leads to irreversible transformations into PbI2, whereas materials with only iodine go through transformations into hexagonal polytypes, such as the 4H-FAPbI3 phase. This work sheds light on the structural impacts of adding bromine on thermodynamic phase stability and provides new insights into the importance of understanding the complexity of phase transformations and secondary phases in mixed-cation and mixed-halide systems.

Synergistic Role of Water and Oxygen Leads to Degradation in Formamidinium-Based Halide Perovskites.

Mixed-cation metal halide perovskites have shown remarkable progress in photovoltaic applications with high power conversion efficiencies. However, to achieve large-scale deployment of this technology, efficiencies must be complemented by long-term durability. The latter is limited by external factors, such as exposure to humidity and air, which lead to the rapid degradation of the perovskite materials and devices. In this work, we study the mechanisms causing Cs and formamidinium (FA)-based halide perovskite phase transformations and stabilization during moisture and air exposure. We use in situ X-ray scattering, X-ray photoelectron spectroscopy, and first-principles calculations to study these chemical interactions and their effects on structure. We unravel a surface reaction pathway involving the dissolution of FAI by water and iodide oxidation by oxygen, driving the Cs/FA ratio into thermodynamically unstable regions, leading to undesirable phase transformations. This work demonstrates the interplay of bulk phase transformations with surface chemical reactions, providing a detailed understanding of the degradation mechanism and strategies for designing durable and efficient perovskite materials.

Resolving Nonlinear Recombination Dynamics in Semiconductors via Ultrafast Excitation Correlation Spectroscopy: Photoluminescence versus Photocurrent Detection.

We explore the application of excitation correlation spectroscopy to detect nonlinear photophysical dynamics in two distinct semiconductor classes through time-integrated photoluminescence and photocurrent measurements. In this experiment, two variably delayed femtosecond pulses excite the semiconductor, and the time-integrated photoluminescence or photocurrent component arising from the nonlinear dynamics of the populations induced by each pulse is measured as a function of inter-pulse delay by phase-sensitive detection with a lock-in amplifier. We focus on two limiting materials systems with contrasting optical properties: a prototypical lead-halide perovskite (LHP) solar cell, in which primary photoexcitations are charge photocarriers, and a single-component organic-semiconductor diode, which features Frenkel excitons as primary photoexcitations. The photoexcitation dynamics perceived by the two detection schemes in these contrasting systems are distinct. Nonlinear-dynamic contributions in the photoluminescence detection scheme arise from contributions to radiative recombination in both materials systems, while photocurrent arises directly in the LHP but indirectly following exciton dissociation in the organic system. Consequently, the basic photophysics of the two systems are reflected differently when comparing measurements with the two detection schemes. Our results indicate that photoluminescence detection in the LHP system provides valuable information about trap-assisted and Auger recombination processes, but that these processes are convoluted in a nontrivial way in the photocurrent response and are therefore difficult to differentiate. In contrast, the organic-semiconductor system exhibits more directly correlated responses in the nonlinear photoluminescence and photocurrent measurements, as charge carriers are secondary excitations only generated through exciton dissociation processes. We propose that bimolecular annihilation pathways mainly contribute to the generation of charge carriers in single-component organic semiconductor devices. Overall, our work highlights the utility of excitation correlation spectroscopy in modern semiconductor materials research, particularly in the analysis of nonlinear photophysical processes, which are deterministic for their electronic and optical properties.

Solvent and A-Site Cation Control Preferred Crystallographic Orientation in Bromine-Based Perovskite Thin Films.

Preferred crystallographic orientation in polycrystalline films is desirable for efficient charge carrier transport in metal halide perovskites and semiconductors. However, the mechanisms that determine the preferred orientation of halide perovskites are still not well understood. In this work, we investigate crystallographic orientation in lead bromide perovskites. We show that the solvent of the precursor solution and organic A-site cation strongly affect the preferred orientation of the deposited perovskite thin films. Specifically, we show that the solvent, dimethylsulfoxide, influences the early stages of crystallization and induces preferred orientation in the deposited films by preventing colloidal particle interactions. Additionally, the methylammonium A-site cation induces a higher degree of preferred orientation than the formamidinium counterpart. We use density functional theory to show that the lower surface energy of the (100) plane facets in methylammonium-based perovskites, compared to the (110) planes, is the reason for the higher degree of preferred orientation. In contrast, the surface energy of the (100) and (110) facets is similar for formamidinium-based perovskites, leading to lower degree of preferred orientation. Furthermore, we show that different A-site cations do not significantly affect ion diffusion in bromine-based perovskite solar cells but impact ion density and accumulation, leading to increased hysteresis. Our work highlights the interplay between the solvent and organic A-site cation which determine crystallographic orientation and plays a critical role in the electronic properties and ionic migration of solar cells.

Formation of a Secondary Phase in Thermally Evaporated MAPbI3 and Its Effects on Solar Cell Performance.

Thermal evaporation is a promising deposition technique to scale up perovskite solar cells (PSCs) to large areas, but the lack of understanding of the mechanisms that lead to high-quality evaporated methylammonium lead triiodide (MAPbI3) films gives rise to devices with efficiencies lower than those obtained by spin coating. This work investigates the crystalline properties of MAPbI3 deposited by the thermal coevaporation of PbI2 and MAI, where the MAI evaporation rate is controlled by setting different temperatures for the MAI source and the PbI2 deposition rate is controlled with a quartz crystal microbalance (QCM). Using grazing incident wide-angle X-ray scattering (GIWAXS) and X-ray diffraction (XRD), we identify the formation of a secondary orthorhombic phase (with a Pnma space group) that appears at MAI source temperatures below 155 °C. With synchrotron-based X-ray fluorescence (XRF) microscopy, we show that the changes in crystalline phases are not necessarily due to changes in stoichiometry. The films show a stochiometric composition when the MAI source is heated between 140 to 155 °C, and the samples become slightly MAI rich at 165 °C. Increasing the MAI temperature beyond 165 °C introduces an excess of MAI in the film, which promotes the formation of films with low crystallinity that contain low-dimensional perovskites. When they are incorporated in solar cells, the films deposited at 165 °C result in the champion power conversion efficiency, although the presence of a small amount of low-dimensional perovskite may lead to a lower open-circuit voltage. We hypothesize that the formation of secondary phases in evaporated films limits the performance of PSCs and that their formation can be suppressed by controlling the MAI source temperature, bringing the film toward a phase-pure tetragonal structure. Control of the phases during perovskite evaporation is therefore crucial to obtain high-performance solar cells.

Monolithically Integrated Perovskite Semiconductor Lasers on Silicon Photonic Chips by Scalable Top-Down Fabrication.

Metal-halide perovskites are promising lasing materials for the realization of monolithically integrated laser sources, the key components of silicon photonic integrated circuits (PICs). Perovskites can be deposited from solution and require only low-temperature processing, leading to significant cost reduction and enabling new PIC architectures compared to state-of-the-art lasers realized through the costly and inefficient hybrid integration of III-V semiconductors. Until now, however, due to the chemical sensitivity of perovskites, no microfabrication process based on optical lithography (and, therefore, on existing semiconductor manufacturing infrastructure) has been established. Here, the first methylammonium lead iodide perovskite microdisc lasers monolithically integrated into silicon nitride PICs by such a top-down process are presented. The lasers show a record low lasing threshold of 4.7 µJcm-2 at room temperature for monolithically integrated lasers, which are complementary metal-oxide-semiconductor compatible and can be integrated in the back-end-of-line processes.