Correction: Development of an enhanced analytical method utilizing pepper matrix as an analyte protectant for sensitive GC‒MS/MS detection of dimethipin in animal-based food products.

[This corrects the article DOI: 10.1371/journal.pone.0295968.].

Development of an enhanced analytical method utilizing pepper matrix as an analyte protectant for sensitive GC‒MS/MS detection of dimethipin in animal-based food products.

Herein, an analytical method using gas chromatography-tandem mass spectrometry (GC‒MS/MS) was devised to detect the presence of the troublesome pesticide dimethipin in various animal-based food products, including chicken, pork, beef, eggs, and milk. The injection port was primed with a matrix derived from pepper leaves that acts as an analyte protectant (AP) to safeguard the target compound from thermal degradation during gas chromatography. The presence of AP resulted in a remarkable limit of quantification of 0.005 mg/kg for dimethipin in five matrices. Three different versions (original, EN, and AOAC) of the QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Safe) method were compared for dimethipin extraction, with a double-layer solid-phase extraction (SPE) cartridge utilized for matrix purification. A seven-point external calibration curve was established for dimethipin in the five matrices, demonstrating excellent linearity with determination coefficients (R2) ≥ 0.998. The developed quantitative method was validated by fortifying each matrix with three different concentrations of standard dimethipin, and the average recovery fell within the acceptable range outlined in the CODEX guidelines (ranging from 88.8% to 110.0%), with a relative standard deviation (RSD) of ≤ 11.97%. This method effectively addresses the challenge of analyzing dimethipin and can therefore be used as a routine monitoring tool for dimethipin across various matrices.

Simultaneous Determination of Pyridate, Quizalofop-ethyl, and Cyhalofop-butyl Residues in Agricultural Products Using Liquid Chromatography-Tandem Mass Spectrometry.

An analytical method was developed to simultaneously determine pyridate, quizalofop-ethyl, and cyhalofop-butyl in brown rice, soybean, potato, pepper, and mandarin using LC-MS/MS. Purification was optimized using various sorbents: primary−secondary amine, octadecyl (C18) silica gel, graphitized carbon black, zirconium dioxide-modified silica particles, zirconium dioxide-modified silica particles (Z-SEP), and multi-walled carbon nanotubes (MWCNTs). Three versions of QuECHERS methods were then tested using the optimal purification agent. Finally, samples were extracted using acetonitrile and QuEChERS EN salts and purified using the Z-SEP sorbent. A six-point matrix-matched external calibration curve was constructed for the analytes. Good linearity was achieved with a determination coefficient ≥0.999. The limits of detection and quantification were 0.0075 mg/kg and 0.01 mg/kg, respectively. The method was validated after fortifying the target standards to the blank matrices at three concentration levels with five replicates for each concentration. The average recovery was within an acceptable range (70−120%), with a relative standard deviation <20%. The applicability of the developed method was evaluated with real-world market samples, all of which tested negative for these three herbicide residues. Therefore, this method can be used for the routine analysis of pyridate, quizalofop-ethyl, and cyhalofop-butyl in agricultural products.

Development of Lignin-Containing Cellulose Nanofibrils Coated Paper-Based Filters for Effective Oil-Water Separation.

New methods of oil-water separation are needed as industrialization has increased the prevalence of oil-water mixtures on Earth. As an abundant and renewable resource with high oxygen and grease barrier properties, mechanically refined cellulose nanofibrils (CNFs) may have promising applications for oil-water separations. The unbleached form of these nanofibrils, lignin-containing CNFs (LCNFs), have also been found to display extraordinary barrier properties and are more environmentally friendly and cost-effective than CNFs. Herein, both wet and dry LCNF-modified filter papers have been developed by coating commercial filter paper with an LCNF suspension utilizing vacuum filtration. The LCNF-modified filters were tested for effectiveness in separating oil-water emulsions, and a positive relationship was discovered between a filter's LCNF coat weight and its oil collection capabilities. The filtration time was also analyzed for various coat weights, revealing a trend of high flux for low LCNF coat weights giving-way-to predictions of a coat weight upper limit. Additionally, it was found that wet filters tend to have higher flux values and oil separation efficiency values than dry filters of the same LCNF coat weight. Results confirm that the addition of LCNF to commercial filter papers has the potential to be used in oil-water separation.

Highly Efficient Iron Oxide Nanoparticles Immobilized on Cellulose Nanofibril Aerogels for Arsenic Removal from Water.

The application and optimal operation of nanoparticle adsorbents in fixed-bed columns or industrial-scale water treatment applications are limited. This limitation is generally due to the tendency of nanoparticles to aggregate, the use of non-sustainable and inefficient polymeric resins as supporting materials in fixed-bed columns, or low adsorption capacity. In this study, magnesium-doped amorphous iron oxide nanoparticles (IONPs) were synthesized and immobilized on the surface of cellulose nanofibrils (CNFs) within a lightweight porous aerogel for arsenic removal from water. The IONPs had a specific surface area of 165 m2 g-1. The IONP-containing CNF aerogels were stable in water and under constant agitation due to the induced crosslinking using an epichlorohydrin crosslinker. The adsorption kinetics showed that both As(III) and As(V) adsorption followed a pseudo second-order kinetic model, and the equilibrium adsorption isotherm was best fitted using the Langmuir model. The maximum adsorption capacities of CNF-IONP aerogel for As(III) and As(V) were 48 and 91 mg As g-IONP-1, respectively. The optimum IONP concentration in the aerogel was 12.5 wt.%, which resulted in a maximum arsenic removal, minimal mass loss, and negligible leaching of iron into water.

Onsite/on-field analysis of pesticide and veterinary drug residues by a state-of-art technology: A review.

Pesticides and veterinary drugs are generally employed to control pests and insects in crop and livestock farming. However, remaining residues are considered potentially hazardous to human health and the environment. Therefore, regular monitoring is required for assessing and legislation of pesticides and veterinary drugs. Various approaches to determining residues in various agricultural and animal food products have been reported. Most analytical methods involve sample extraction, purification (cleanup), and detection. Traditional sample preparation is time-consuming labor-intensive, expensive, and requires a large amount of toxic organic solvent, along with high probability for the decomposition of a compound before the analysis. Thus, modern sample preparation techniques, such as the quick, easy, cheap, effective, rugged, and safe method, have been widely accepted in the scientific community for its versatile application; however, it still requires a laboratory setup for the extraction and purification processes, which also involves the utilization of a toxic solvent. Therefore, it is crucial to elucidate recent technologies that are simple, portable, green, quick, and cost-effective for onsite and infield residue detections. Several technologies, such as surface-enhanced Raman spectroscopy, quantum dots, biosensing, and miniaturized gas chromatography, are now available. Further, several onsite techniques, such as ion mobility-mass spectrometry, are now being upgraded; some of them, although unable to analyze field sample directly, can analyze a large number of compounds within very short time (such as time-of-flight and Orbitrap mass spectrometry). Thus, to stay updated with scientific advances and analyze organic contaminants effectively and safely, it is necessary to study all of the state-of-art technology.

Establishment of import tolerance for the insecticide thiacloprid in strawberry.

To promote exports, import tolerance (IT) of thiacloprid in strawberry was proposed using the Organization for Economic Cooperation and Development (OECD) maximum residue limit (MRL) calculator after conducting three different field trials. The pre-harvest interval of residual pattern and degradation dynamics of thiacloprid in strawberry were determined using ultra-performance liquid chromatography-tandem mass spectrometry. Samples were extracted with acetonitrile and a mixture of salts and dilution was performed for purification. A six-point matrix-matched calibration curve was constructed which provided excellent linearity with coefficient of determination (R2 ) of 0.9998 or more. Detection and quantification limits were 0.003 and 0.01 mg/kg, respectively. The method was validated in quintuplicate at three different concentrations, which resulted in acceptable recovery ranging from 80.86% to 101.71% with relative standard deviation of 6.50 or less among the three field sites. The developed method was applied to the field-treated sample harvested at different intervals. In the pre-harvest interval trial, the amount of thiacloprid residues ranged from 0.24 to 0.70 mg/kg in field site 1 (Nonsan), 0.16 to 0.50 mg/kg in field site 2 (Sunchang), and 0.36 to 0.50 mg/kg in field site 3 (Sacheon). By contrast, in the degradation trial, the observed residues were 0.03-0.81 mg/kg in field site 1 and 0.02-0.48 mg/kg in field site 2. Consequently, the IT of thiacloprid in strawberry using the OECD MRL calculator was proposed as 2 mg/kg, which is exactly the same as the MRL established by the Republic of Korea. In conclusion, the residue study proposes 2.0 mg/kg as the MRL of thiacloprid in strawberries.

Quantification of spinosyn A and spinosyn D in animal-derived products using multiwalled carbon nanotubes coupled with LC-MS/MS for analysis.

An analytical method was developed for the quantification of spinosad (sum of spinosyns A and D) in five animal-derived products (chicken breast, pork, beef, egg, and milk) using LC-MS/MS. The sample was extracted using acetonitrile/1% acetic acid and a combination of magnesium sulfate and sodium acetate salts. The sample was purified using multiwalled carbon nanotubes as sorbent via a dispersive-solid-phase extraction procedure. Matrix-matched calibration (seven-point) provided good linearity with coefficient of determination (R2 ) ≥0.99 for each product. The limits of detection and quantification (LOQs) ranged between 0.0003-0.03 and 0.001-0.1 mg/kg, respectively. Method validation was carried out after spiking the target standard to blank matrices at the concentration levels of LOQ, 2 × LOQ, and 10 × LOQ with three replicates for each. The average recoveries were between 74 and 104%, with relative standard deviations ≤9.68, which were within the acceptable range designated by the international organizations. The developed method was successfully applied for monitoring market samples collected throughout the Korean Peninsula, and none of the samples tested positive for the target analytes. It has therefore been shown that dehydration and acidification were effective to extract spinosad from animal-derived products.

Upgrading analytical methodology through comparative study for screening of 267 pesticides/metabolites in five representative matrices using UPLC-MS/MS.

A comparative study was conducted to replace the traditional screening method (MFDS#83) with the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) EN method for the determination of 267 pesticides/metabolites/plant activators/growth regulators in five representative crop matrices (mandarin, pepper, potato, rice, and soybean). In the traditional method, samples were extracted with acetonitrile and salt, and purified with a solid-phase extraction cartridge. In the QuEChERS method, the sample extraction was carried out using acetonitrile and a mixture of salts, and purification was performed using dispersive solid phase extraction. The limit of quantification (LOQ) for the MFDS#83 method was 0.0004 mg/kg, whereas for the QuEChERS EN method, the LOQ varied from 0.002 to 0.006 mg/kg for all analytes in various matrices. A six-point matrix-matched calibration curve was prepared for all analytes in five matrices for both methods. Both the MFDS#83 and QuEChERS EN methods provided excellent linearity, with the coefficients of determination (R2) ≥ 0.99 for most of the compounds. In both cases, the method was validated in terms of recovery and repeatability after the fortification of two different concentrations with three replicates for each of the concentrations. The QuEChERS EN method provided better recovery than the MFDS#83 method for all matrices except mandarin.

An effective methodology for simultaneous quantification of thiophanate-methyl, and its metabolite carbendazim in pear, using LC-MS/MS.

Herein we have developed an optimized analytical method for the simultaneous quantification of a fungicide, thiophanate-methyl, and its metabolite, carbendazim, in pear cultivated under open-field conditions using liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS). Due to the problem of partitioning associated with using acetonitrile and salts, methanol was used for sample extraction; the extract was then filtered using a vacuum filter, and cleaned-up using C18 QuEChERS bulk sorbent following dispersive solid-phase extraction (d-SPE) procedure. Since a common problem, "matrix effect", associated with the matrix was observed in LC-MS/MS, calibration curves for both thiophanate-methyl and carbendazim were constructed in the matrix using seven different concentration levels. Excellent linearity was observed, with determinant coefficient (R2) ≥ 0.9990. The limits of quantification (LOQs) were ≤0.02 mg/kg, satisfactory in terms of the maximum residue limits. Methods were validated at two fortification concentrations (10 × LOQ and 50 × LOQ); the experiments were repeated three times for each level and the average recoveries were 75.00-84.92%, with the coefficient of variation (CV) being ≤5.78%. The developed analytical method was applied to pear samples previously sprayed with commercial thiophanate-methyl formulation four times on different days during pre-harvest treatment. The parent compound was converted to its metabolites and the total residues degraded continuously until harvest. The data obtained in this study could help set safety guidelines for thiophanate-methyl in pear.

Determination of endrin and δ-keto endrin in five food products of animal origin using GC-µECD: A modified QuEChERS approach to traditional detection.

A simple quick, easy, cheap, effective, rugged, and safe (QuEChERS)-based method was developed for the analysis of endrin and its metabolite, δ-keto endrin, in five animal-derived food products (chicken, pork, beef, egg, and milk) using a gas chromatography-micro electron capture detector (GC-µECD). Samples were extracted with acidified acetonitrile, salted out with magnesium sulfate and sodium acetate, and finally purified with a dual layer solid-phase extraction cartridge (SPE) that contains both Supelclean ENVI-Carb (upper layer) and primary secondary amine (lower layer) SPE sorbents. A seven-point external calibration curve was constructed both for the solvent and matrix for both compounds. Good linearity was achieved for both analytes, with coefficients of determination (R2) ≥ 0.9960. The limits of detection (LODs) were 0.003 mg/kg, whereas the limits of quantification (LOQ) were 0.01 mg/kg, which were 10 times lower than the extraneous maximum residue limit (EMRL) designated by CODEX Alimentarius for the specified matrices. The method was validated via recovery performances in triplicates, with three fortification levels equivalent to LOQ, 2 × LOQ, and 10 × LOQ. The method provided excellent recoveries, ranging between 75.63 and 117.92%, with relative standard deviations (RSD) ≤ 8.52% for both analytes in various matrices. The developed method was successfully applied to monitor market samples collected from 20 different places throughout the Republic of Korea, and none of the tested analytes were found in the analyzed samples. Conclusively, we could propose that the current method can be used for routine analysis of endrin and δ-keto endrin in any type of fatty food matrix.

Method development, matrix effect, and risk assessment of 49 multiclass pesticides in kiwifruit using liquid chromatography coupled to tandem mass spectrometry.

In the present study, a liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS) method with a minimal matrix effect (ME) was developed and validated for simultaneous determination of a diverse range of pesticides (49) in kiwifruit. Samples extracted by the quick, easy, cheap, effective, rugged, and safe (QuEChERS) citrate-buffered method were analyzed either without purification or following purification (with primary secondary amine (PSA) or PSA + graphitized carbon black (GCB)). With the addition of a clean-up step, the suppression of the ME decreased, with a higher number of pesticides determined by the application of PSA + GCB. The method exhibited good linearity with coefficients of determination (R2) ≥ 0.9972 and satisfactory recoveries (70-120%) with a relative standard deviations (RSDs) <10%. The limits of quantification (LOQ) were lower than the maximum residue limits (MRLs) set by the Korean Ministry of Food and Drug Safety (MFDS) and the CODEX Alimentarius. The developed method was applied to the real samples and the results indicated that the quantitated levels of all pesticides, except for pyraclostrobin and carbendazim, are lower than the MRLs set by the regulatory authorities. The percentage of the acceptable daily intake was <20%, suggesting that there is no risk associated with the intake of residual pesticides through kiwifruit.

Dynamic residual pattern of azoxystrobin in Swiss chard with contribution to safety evaluation.

This study aimed at quantifying the residual amount of azoxystrobin in Swiss chard samples grown under greenhouse conditions at two different locations (Gwangju and Naju, Republic of Korea). Samples were extracted with acetonitrile, separated by salting out, and subjected to purification by using solid-phase extraction. The analyte was identified using liquid chromatography-ultraviolet detection. The linearity of the calibration range was excellent with coefficient of determination 1.00. Recovery at three different spiking levels (0.1, 0.5, and 4 mg/kg) ranged between 82.89 and 109.46% with relative standard deviation <3. The limit of quantification, 0.01 mg/kg, was considerably much lower than the maximum residue limit (50 mg/kg) set by the Korean Ministry of Food and Drug Safety. The developed methodology was successfully used for field-treated leaves, which were collected randomly at 0-14 days following azoxystrobin application. The rate of disappearance in/on Swiss chard was ascribed to first-order kinetics with a half-life of 8 and 5 days, in leaves grown in Gwangju and Naju greenhouses, respectively. Risk assessments revealed that the acceptable daily intake percentage is substantially below the risk level of consumption at day 0 (in both areas), thus encouraging its safe consumption.

A quick and effective methodology for analyzing dinotefuran and its highly polar metabolites in plum using liquid chromatography-tandem mass spectrometry.

A simple and effective method was developed for analyzing dinotefuran and its three metabolites (MNG, UF, and DN) in plum using liquid chromatography-tandem mass spectrometry (LC-MS/MS). Due to the polarity and high water miscibility, dinotefuran and some of its metabolites (especially DN) have some limitations to be extracted with acetonitrile and salt following the "QuEChERS" sample preparation methodology. Alternatively, the samples were extracted with methanol, and purified with dispersive-solid phase extraction procedure (d-SPE) using primary secondary amine (PSA) and C18 sorbents after filtration, and mass up. Due to the suppression effect originated from plum matrix, matrix-matched calibration curves, which provided good linearity with coefficient of determination (R2)≥0.998, were used for quantification of all analytes. Blank plum samples fortified with 2 spiking levels (10×LOQ and 50×LOQ) yielded satisfactory recoveries for all tested analytes in the range of 83.01 to 110.18% with relative standard deviation (RSD)≤8.91. The method was successfully applied to field-incurred plum samples and dinotefuran and all metabolites were positively detected and quantified. In conclusion, we suggest that the method can be expanded to polar compounds having solvent and partitioning problems in any of the versions of QuEChERS.

Dissipation kinetics, pre-harvest residue limits, and dietary risk assessment of the systemic fungicide metalaxyl in Swiss chard grown under greenhouse conditions.

The residual behavior of the systemic fungicide, metalaxyl, in Swiss chard cultivated at two different locations under greenhouse conditions was investigated using high-performance liquid chromatography coupled with an ultraviolet detector (HPLC-UVD). Samples were randomly collected over 14 days and extracted using acetonitrile, partitioned using solid sodium chloride, and a solid-phase extraction (SPE) NH2 cartridge was used for cleanup. The linearity over a concentration range 0.05-50 mg/L was excellent with a coefficient of determination (R2) of 0.9997. The recovery rate ranged from 77.05 to 88.92% with relative standard deviations (RSDs) ≤ 10.74, and the limits of detection (LOD) and quantification (LOQ) were 0.0033 and 0.01 mg/kg, respectively. The initial (2 h after application) deposits were 4.69 and 5.90 mg/kg for sites 1 and 2, respectively, which increased to 4.95 and 6.57 mg/kg, respectively, one day post-application, owing to the systemic properties of the fungicide. The dissipation half-life was 5.3 and 6.0 days for sites 1 and 2, respectively. The pre-harvest residue limit (PHRL) suggested that if 55.38 and 47.23 mg/kg was applied 10 days before harvest or 33.28 and 30.73 mg/kg was applied 5 days before harvest (for sites 1 and 2, respectively) then the concentration will fall below the maximum residue limit (MRL = 20.0 mg/kg) at the time of harvest. The dietary risk assessment, estimated as hazard quotient (RQ%), indicate that metalaxyl can be safely used in/on Swiss chard, with no hazardous effects expected for consumers.

Chromatographic determination, decline dynamic and risk assessment of sulfoxaflor in Asian pear and oriental melon.

The dissipation pattern of sulfoxaflor in Asian pear cultivated in an open field conditions and in oriental melon grown under plastic house conditions was each studied in two different locations. Residues in field-treated samples were determined using liquid chromatography coupled with an ultraviolet detector and confirmed by liquid chromatography-tandem mass spectrometry. A calibration curve for sulfoxaflor was linear over the concentration range 0.1-5.0 mg/L, with a coefficient of determination of 0.9999. The limits of detection and quantification (LOQ) were 0.007 and 0.02 mg/kg, respectively. Recoveries at three fortification levels (LOQ, 10 × LOQ and maximum residue limit) ranged from 70.5 to 86.2%, with a relative standard deviation ≤5.8%. The dissipation half-lives were 10.8 and 7.9 days in pear and 5.4 and 5.9 days in oriental melon, at sites 1 and 2, respectively. Based on a pre-harvest residue limit curve, it was predicted that, if the residues at 10 days before harvest in Asian pear are <0.54/0.61 mg/kg and those in oriental melon are <1.43/1.26 mg/kg, then the residue level will be below the maximum residue limit at harvest. Risk assessment at zero days showed a percentage acceptable daily intake of 10.80% in Asian pear and 1.77 and 1.55% in oriental melon, for sites 1 and 2, respectively. These values indicate that the fruits are safe for consumption.

Residual dynamic and risk assessment of dimethomorph in Swiss chard grown at two different sites.

Residue analysis of dimethomorph in Swiss chard cultivated at two different locations under greenhouse conditions was conducted using high-performance liquid chromatography-ultraviolet detection and confirmed by tandem mass spectrometry. The randomly collected samples (over 14 days) were extracted with acetonitrile and purified using a Florisil solid-phase extraction cartridge. Linearity over a concentration range of 0.05-50.0 mg/L had an excellent coefficient of determination of 0.9996. Recovery rate ranged from 82.98 to 95.43% with relative standard deviations ≤5.12% and limits of detection and quantification of 0.003 and 0.01 mg/kg, respectively. The initial deposits [day 0 (2 h post-application)] were considerably lower (7.57 and 8.55 mg/kg for sites 1 and 2, respectively) than the maximum residue limit (30 mg/kg) set by the Korean Ministry of Food and Drug Safety. The dissipation half-life was approximately the same, being 5.0 and 5.1 days for sites 1 and 2, respectively. Risk assessment estimated as acceptable daily intake revealed a value of 0.084 or 0.094% (day 0) and 0.014% (10 days post-application), for sites 1 and 2, respectively. The values indicated that dimethomorph can be safely used on Swiss chard, with no hazardous effects expected for Korean consumers.

Analytical approach, dissipation pattern and risk assessment of pesticide residue in green leafy vegetables: A comprehensive review.

The category of 'leafy vegetables' comprises a wide range of plants, including cabbage, lettuce, leeks, spinach, Swiss chard and kale, and it forms a significant component of the human diet. Typically, leafy vegetables are low in calories and fat, are great sources of vitamins, protein, dietary fibre and minerals (including iron, calcium, and nitrates), and are rich in phytochemicals. To counter the impact of pests on vegetables, a broad variety of pesticides are used. Because of their large surface areas, leafy vegetables are expected to have high residual pesticide levels. As such, a sound analytical approach is needed to detect and quantify residue levels that are equal to or lower than the maximum residue limits, thus rendering the products safe for consumption. Overall, leafy vegetables consumed raw (after a tap water wash only), boiled or steamed contribute 2% of total vegetable consumption globally, and they might have a comparatively greater influence on health than cereal ingestion. Consequently, in this review paper, we highlight the importance of leafy vegetables, the pesticides that are commonly used on them and various analytical techniques, including sample preparation, extraction, clean-up and final detection. The effects on dissipation patterns, pre-harvest residue limits and safety/risks imposed by various pesticides are also reviewed and discussed. In conclusion, environmentally friendly extraction methods coupled with high-throughput techniques with greater reproducibility and lower uncertainty are needed for quantifying residues in leafy vegetables at very low concentrations. Commercial and household food preparation, such as washing, peeling, blanching and cooking are effective in removing most of the pesticide residues that are loosely attached on vegetables.

Electrochemical oxidation of As(iii) on Pd immobilized Pt surface: kinetics and sensing performance.

Pd nanoparticles were electrochemically immobilized on a Pt surface in the presence of sodium dodecyl sulfate (SDS) molecules to study the electrokinetics of arsenite oxidation reactions and the corresponding sensing activities. The X-ray photoelectron spectroscopy (XPS) analysis showed that on the Pt surface, Pd atoms exist as adatoms and the contents of Pd(0) and Pd(ii) were 75.72 and 24.28 at%, respectively, and the particle sizes were in the range of 61-145 nm. The experimental results revealed that the catalytic efficiency as well as the charge transfer resistance (at the redox potential of the Fe(ii)/Fe(iii) couple) increased in the order of Pt < Pt-Pd < Pt-Pdsds. A Pt-Pdsds electrode exhibited an open circuit potential (OCP) of 0.65 V in acidic conditions; however, when 50.0 mM NaAsO2 was present, the OCP value shifted to 0.42 V. It has been projected that the As(iii) oxidation proceeds using a sequential pathway: As(iii) → As(iv) → As(v). After optimization of the square wave voltammetric data, the limits of detection of As(iii) were obtained as 1.3 µg L-1 and 0.2 µg L-1 when the surface modification of the Pt surface was executed with Pd particles in the absence and presence of the SDS surfactant, respectively. Finally, real samples were analyzed with excellent recovery performance.

Decline patterns and risk assessment of 10 multi-class pesticides in young sprout amaranth (Amaranthus mangostanus) under greenhouse growing conditions.

The present study was designed to investigate the residual decline pattern and the risk assessment of 10 different class pesticides, namely azoxystrobin, boscalid, diazinon, diethofencarb, difenoconazole, etofenprox, flubendiamide, paclobutrazol, and pyraclostrobin in young vegetative amaranth (Amaranthus mangostanus) sprayed once or twice under greenhouse growing conditions. Field-incurred samples, collected at 3, 7, or 10 days after application of both treatments, were extracted and purified with the quick, easy, cheap, effective, rugged, and safe "QuEChERS" citrate-buffered method and analyzed with liquid chromatography-electrospray ionization tandem mass spectrometry (LC-MS/MS) in positive ion mode. The linearity was satisfactory with determination coefficients (R 2) falling between 0.9817 and 0.9999 and limits of detection (LOD) and quantification (LOQ) values of 0.0007 and 0.002 mg/kg, respectively. The mean recovery rate at four spiking levels (equivalent to 5, 10, 50, and 100 × LOQ) ranged from 78.1 to 131.6% with a relative standard deviation (RSD) of < 11%. Substantial differences in the initial deposit between the tested analytes were observed and clearly indicated that the structure, as well as the initial concentration of applied products, greatly affected the residue deposit. From the obtained residual data, the provisional marginal maximum residue limits (MRLs) and the pre-harvest intervals (PHI) were proposed. Risk assessment was evaluated by comparing the theoretical maximum daily intake (TMDI) with the acceptable daily intake (ADI). Herein, the TMDI was lower than the ADI (TMDI/ADI ratio ≤ 80% set by the Korean Ministry of Food and Drug Safety) except for difenoconazole (80.92%, marginally higher), indicating that the vegetative amaranth is not hazardous and can be consumed safely by Korean consumers.