Determination of oil reservoir radiotracer (S14CN-) in a single step using a plastic scintillator extractive resin.

The analysis of radiotracers is important in the study of oil reservoir dynamics. One of the most widely used radiotracer is S(14)CN(-). Prior to activity measurements by Liquid Scintillation (LS), routine determinations require the pretreatment steps of purification and concentration of the samples using anion exchange columns. The final elution media produces samples with high salt concentration that may lead to problems with phase separation during the LS measurement. Plastic Scintillation (PS) is an alternative technique that provides a solid surface that can be used as a platform for the immobilisation of selective extractants to obtain a PS resin. The proposed procedure unifies chemical separation and sample measurement preparation in a single step, serving to reduce the number of reagents needed and manpower required for the analysis while also avoiding mixed waste production by LS. The objective of this study is to develop a PS resin for the determination of (14)C-labelled thiocyanate radiotracer in water samples. For this purpose, the immobilisation procedure was optimised, including optimisation of the proportion of PS microspheres:extractant and the use of a control blank to monitor the PS resin immobilisation process. The breakthrough volume was studied and the detection and quantification limits for 100 mL of sample were determined to be 0.08 Bq L(-1) and 0.31 Bq L(-1), respectively. The established procedure was applied to active samples from oil reservoirs and errors lower than 5% in the sample determinations were obtained.

The implications of particle energy and acidic media on gross alpha and gross beta determination using liquid scintillation.

The interaction of humans with radioactivity present in the environment from natural and artificial sources necessitates an evaluation of its risk on human health. Gross alpha and gross beta activities can provide a rapid evaluation of the radioactive content of a sample and can be simultaneously determined by using liquid scintillation counters. However, calibration of the liquid scintillation counter is required and is affected by many factors, such as particle energy and the acidity of the media. This study investigates what effect the particle energy used for calibration has on misclassification and how to account for this misclassification in routine measurements. The variability in measurement produced by the final pH, as well as any acids used in sample treatment, was also studied. These results showed that the most commonly used acid for these types of analyses, HNO(3), produced a high amount of misclassifications at very low pH. The results improved when HCl was used to adjust the sample to low pH.

Mixture quantification using PLS in plastic scintillation measurements.

This article reports the capability of plastic scintillation (PS) combined with multivariate calibration (Partial least squares; PLS) to detect and quantify alpha and beta emitters in mixtures. While several attempts have been made with this purpose in mind using liquid scintillation (LS), no attempt was done using PS that has the great advantage of not producing mixed waste after the measurements are performed. Following this objective, ternary mixtures of alpha and beta emitters ((241)Am, (137)Cs and (90)Sr/(90)Y) have been quantified. Procedure optimisation has evaluated the use of the net spectra or the sample spectra, the inclusion of different spectra obtained at different values of the Pulse Shape Analysis parameter and the application of the PLS1 or PLS2 algorithms. The conclusions show that the use of PS+PLS2 applied to the sample spectra, without the use of any pulse shape discrimination, allows quantification of the activities with relative errors less than 10% in most of the cases. This procedure not only allows quantification of mixtures but also reduces measurement time (no blanks are required) and the application of this procedure does not require detectors that include the pulse shape analysis parameter.

Radiostrontium separation and measurement in a single step using plastic scintillators plus selective extractants. Application to aqueous sample analysis.

This study describes a new protocol for (90)Sr determination in water samples based on the use of a selective extractant (DtBuCH18C6) and plastic scintillator microspheres. The proposed procedure unifies chemical separation and sample measurement preparation in a single step to reduce the effort, time and reagents required for analysis. In addition, the final measurement does not produce mixed waste. The minimum activity detectable for 10 mL of sample solution is 0.46 Bq L(-1). Relative errors for the determination of (90)Sr activity in drinking, sea and river waters are less than 4%.

Alpha/beta pulse shape discrimination in plastic scintillation using commercial scintillation detectors.

Activity determination in different types of samples is a current need in many different fields. Simultaneously analysing alpha and beta emitters is now a routine option when using liquid scintillation (LS) and pulse shape discrimination. However, LS has an important drawback, the generation of mixed waste. Recently, several studies have shown the capability of plastic scintillation (PS) as an alternative to LS, but no research has been carried out to determine its capability for alpha/beta discrimination. The objective of this study was to evaluate the capability of PS to discriminate alpha/beta emitters on the basis of pulse shape analysis (PSA). The results obtained show that PS pulses had lower energy than LS pulses. As a consequence, a lower detection efficiency, a shift to lower energies and a better discrimination of beta and a worst discrimination of alpha disintegrations was observed for PS. Colour quenching also produced a decrease in the energy of the particles, as well as the effects described above. It is clear that in PS, the discrimination capability was correlated with the energy of the particles detected. Taking into account the discrimination capabilities of PS, a protocol for the measurement and the calculation of alpha and beta activities in mixtures using PS and commercial scintillation detectors has been proposed. The new protocol was applied to the quantification of spiked river water samples containing a pair of radionuclides ((3)H-(241)Am or (90)Sr/(90)Y-(241)Am) in different activity proportions. The relative errors in all determinations were lower than 7%. These results demonstrate the capability of PS to discriminate alpha/beta emitters on the basis of pulse shape and to quantify mixtures without generating mixed waste.

Comparative study of pre-treatment procedures for (3)H monitoring in water samples from environmental protection programs.

The determination of tritium activity in water samples is included in most environmental protection programs, and the recommended procedure consists of sample distillation and further measurement by liquid scintillation. Distillation is a simple but time consuming pre-treatment, especially in routine analysis. Here we evaluate alternative pre-treatments for tritium activity determination, such as filtration or the use of multiple selective ion exchange columns. 52 samples from different water sources (rain, surface, underground, sea and drinking water) in Spanish environmental protection programs, together with an IAEA reference material were analyzed. Results show that both pre-treatments can be applied as a preliminary tool to discriminate between tritium active and non active waters in environmental monitoring programs. In addition, filtration and multiple selective ion exchange column pre-treatments can be used as alternative procedures for tritium activity determination in the routine analyses of water samples with known and reproducible chemical and isotopic composition. Both methods are less time consuming than distillation and, in the case of filtration, extremely cheap. For waters with complex matrices, especially sea water, distillation is the recommended procedure due to the interference from salts contained in the sample.

Laboratory experiments to characterize radiochloride diffusion in unsaturated soils.

Diffusion transport of (36)Cl was examined in seven soils under unsaturated conditions in tubes packed with two portions of each soil having different (36)Cl activity concentrations. Apparent diffusion coefficients (D(a)) derived from diffusion profiles varied within a narrow range (from 3x10(-10) to 7x10(-10) m(2) s(-1)) confirming the minor effect of soil properties on the diffusion of a non-reactive radionuclide like (36)Cl. Instead, packing conditions had a major effect. Solid-liquid distribution coefficients (K(d)) derived from D(a) (0.02-0.2 L kg(-1)) were systematically lower than those obtained from batch experiments (0.6-1.0 L kg(-1)), but with a similar variation pattern among soils. The low values of K(d) (Cl) confirmed an almost negligible radiochloride-soil interaction.

Establishment of a method for the rapid measurement of gross alpha and gross beta activities in sea water.

The risk associated with NORM and with their redistribution in the environment due to human activities requires rapid methods which can be applied to a wide range of samples. The present work studies the effect that salts present in sea water have in the gross alpha/beta determination using low-level liquid scintillation counting and a new method is established. This is done from a previously established method for such determinations in non-saline water. External quenching parameter, efficiency, spectra position and interference values are evaluated to look for differences in matrix behaviour. Some quality parameters of the new method are reported.

Plastic vs. liquid scintillation for 14C radiotracers determination in high salt matrices.

The use of radiotracers is a common procedure for better understanding of the dynamics of oil reservoirs. Several molecules and radionuclides are implemented for this purpose; one of these is (14)C labelled thiocyanate. Samples taken from fluids in production wells require a pre-treatment step in order to purify and concentrate the activity of the radiotracer before measurement. Pre-treatment is based on ionic exchange and the solution eluted includes a high concentration of salt that can be a serious drawback for the development of a stable emulsion when the liquid sample and the scintillation cocktail are mixed for Liquid Scintillation (LS). The objective of this study is to evaluate the capability of Plastic Scintillation (PS) to determine the activity of radiotracers in salt matrices. For this purpose, an initial comparative study of the influence of salt and coloured matrices on the detection efficiency for PS and LS was performed. Results indicate that in both techniques colour quenching produces the same effects: efficiency decrease and spectra shift, whereas salt quenching produces different effects for PS and LS, ionization quenching for PS and chemical quenching for LS. As a result of this divergence, the calibration required for each counting method is different: two steps for PS and a single step for LS. After system study and procedure optimization, radiotracer activities in real samples taken from oil reservoirs have been determined. The results indicated that PS shows similar capability to the classical LS to determine the activity in these salt matrix samples with the additional advantages that no separation of the phase can appear and no mixed waste is produced after measurement.

pH(stat) vs. single extraction tests to evaluate heavy metals and arsenic leachability in environmental samples.

Here we compared the pH(stat) test, which examines the leachability of major elements (Ca, Mg, Al, Fe, and Mn), dissolved organic carbon, and trace elements (Cd, Zn, Cu, Pb, and As) in a wide pH range, with single extraction tests based on the use of mild extractants (calcium chloride, acetic acid or EDTA). For this purpose, we examined samples from a variety of environmental conditions (sludges, mineral soils, organic soils, and soils with particulate and/or soluble contamination). Extraction yields obtained with CaCl(2) (0.01 mol L(-1)) and CH(3)COOH (0.43 mol L(-1)) correlated well with those from the pH(stat) at the same pH (r=0.98 and 0.95, respectively), while the use of EDTA (0.05 mol L(-1)) led to systematically higher extraction yields than those quantified with the pH(stat) at the same pH. However, the pH(stat) test had three distinct advantages: (1) it revealed the relationship between the solubility of the main soil phases and pH; (2) it showed the variation in pollutant leachability due to changes in pH; and (3) it better predicted the maximum contaminant availability. Thus we propose that the pH(stat) is the best laboratory tests to evaluate the contaminant leachability over a wide range of sample types (soil, sludge, and sediment).

Radionuclide sorption-desorption pattern in soils from Spain.

The pattern of radiostrontium and radiocesium sorption-desorption was examined in 30 Spanish soils by the quantification of the distribution coefficients (Kd) with batch tests, the evaluation of sorption reversibility with a single extraction, the estimation of sorption dynamics by the application of drying-wetting cycles, and the calculation of Kdadjusted values as an input for risk assessment models. The data obtained overlapped with those found in soils from other climatic areas, suggesting identical interaction mechanisms and allowing the extrapolation of parameterisations and prediction models among different scenarios.

Use of the modified BCR three-step sequential extraction procedure for the study of trace element dynamics in contaminated soils.

The modified BCR three-step sequential extraction procedure was used to examine the temporal dynamics of trace elements in soils contaminated by an accidental spill from an opencast mine in south-west Spain. Soils were mainly contaminated with pyritic sludge and acidic wastewater, whereas some soils were affected only by acidic wastewater. The distributions obtained for both some major (Ca, Fe and Mn) and trace elements (As, Cd, Cu, Pb and Zn) in the sludge and soil samples taken at different times after the accident, 1-3 months and 21 months, were compared. Sequential extractions were useful in identifying different sources of contamination, and in obtaining additional information on the solubility of secondary minerals formed by pyrite oxidation. Thus, the effectiveness of the BCR procedure has proved to be a useful tool for predicting short- and long-term mobility of trace elements, even in complex environmental scenarios.

Prediction of radionuclide aging in soils from the Chernobyl and Mediterranean areas.

The aging of soil-pollutant interaction, which may lead to an increase in pollutant fixation, is the main driving force in the natural attenuation of contaminated soils. Here a test was evaluated to predict the aging of radiostrontium and radiocesium in soils from the Chernobyl and Mediterranean areas. After contamination, soils were maintained at various temperatures for up to 12 mo, with or without drying-wetting (DW) cycles. Changes in the quantity of radionuclide reversibly sorbed over time were monitored using an extraction test (1 mol L(-1) NH(4)Cl; 10 mL g(-1); 16 h). The fixed fraction could not be predicted from soil properties controlling the sorption step. Aging was not as relevant for Sr as for Cs. The time elapsed since contamination was the main factor responsible for the slight (up to 1.3-fold) decreases in Sr extraction yields. The additional effect of DW cycles was negligible. Instead, all factors accelerated Cs aging due to the enhancement of Cs trapping by clay interlayer collapse, with up to 20-fold increases in Cs fixation. The DW cycles also caused secondary effects on the Cs-specific sorption pool, which were beneficial or detrimental depending on the soil type. Extraction yields from laboratory aged samples agreed with those from field samples taken a few years after the Chernobyl accident. These results confirm the prediction capacity of the laboratory test and its usefulness in risk assessment exercises and in the design of intervention actions, particularly because neither fixation nor aging were related to the soil properties, such as clay content.

First approach to radionuclide mixtures quantification by using plastic scintillators. Influence of the diameter of the plastic beads.

Recent studies have evaluated the capability of plastic scintillation (PS) as an alternative to liquid scintillation (LS) in radionuclide activity determination without mixed waste production. In order to complete the comparison, we now assess the extent to which PS can be used to quantify mixtures of radionuclides and the influence of the diameter of the plastic scintillation beads in detection efficiency. The results show that the detection efficiency decreases and the spectrum shrink to lower energies when the size of the plastic scintillation beads increases, and that the lower the energy of the beta particle, the greater the variation takes place. Similar behaviour has been observed for beta-gamma and alpha emitters. Two scenarios for the quantification of mixtures are considered, one including two radionuclides (14C and 60Co) whose spectra do not overlap significantly, and the other including two radionuclides (137Cs and 90Sr/90Y), where the spectra of one the isotopes is totally overlapped by the other The calculation has been performed by using the conventional window selection procedure and a new approach in which the selected windows correspond to those with lower quantification errors. Relative errors obtained using the proposed approach (less than 10%) are lower than those of the conventional procedure, even when a radionuclide is completely overlapped, except for those samples with extreme activity ratios that were not included in the window optimization process.

Effect of the cationic composition of sorption solution on the quantification of sorption-desorption parameters of heavy metals in soils.

We obtained the sorption isotherms of Cd, Cu, Pb and Zn in clay, clay saline and organic soils. The distribution coefficients (K(d)) were determined in 0.02 eq l(-1) CaCl(2) and in a solution that simulated the soil solution cationic composition. The K(d) values greatly varied with the composition of the sorption solution and the initial metal concentration. The sorption experiments were complemented with the quantification of the extractable metal, to estimate the reversibility of metal sorption. The extraction yields depended on the metal-soil combination, and the initial metal concentration, showing no correlation with previous K(d) values. The effect of the solution composition in mobility predictions was estimated through a Retention Factor, defined as the ratio of the K(d) versus the extraction yield. Results showed that risk was over- or underestimated using the CaCl(2) medium in soils with a markedly different soil solution composition.

Combination of chemical separation and data treatment for 55 Fe, 63 Ni, 99 Tc, 137 Cs and 90 Sr/90Y activity determination in radioactive waste by liquid scintillation.

Routine operations involving nuclear reactors and decommissioning activities require numerous chemical analyses. Most of the procedures developed for these chemical characterisations involve several separation steps to prepare the sample for measurement. Chemical treatments are time- and manpower-consuming, labour intensive and produce significant quantities of waste. In order to address this problem, we evaluate a data treatment procedure (multivariate calibration--PLS), which we propose as a substitute to some of these separation steps. Mixtures of beta emitter radionuclides of increasing complexity ((90)Sr/(90)Y--(99)Tc, (90)Sr/(90)Y--(99)Tc--(63)Ni--(137)Cs and (90)Sr/(90)Y--(99)Tc--(63)Ni--(137)Cs--(55)Fe) have been measured by liquid scintillation (LS) counting. The influences of quenching and level of activity was evaluated and the activity of unknown samples determined. Despite the spectra overlapping and low resolution of LS, relative errors in the activities quantification of unknown samples inside the range covered by the calibration matrix are lower than 15% whatever the number of radionuclides included in the solution was.

Effect of chloride on heavy metal mobility of harbour sediments.

To evaluate the environmental impact of polluted sediments, several operationally defined sequential extraction procedures (SEPs) have been described. Salinity has long been recognised as an important variable determining the physicochemical behaviour of heavy metals in marine sediments. Thus, in the present paper, the modified BCR-SEP has been applied to harbour sediments in order to assess to what extent trace metal mobility (Cd, Cr, Cu, Ni, Pb and Zn) could be influenced by chloride content in sediments. For this, washed (W) and non-washed (NW) sediments were compared. The relative mobility order observed for the six trace metals studied was not seen to be influenced by the presence of chloride in the sediments, but an increase of mobility was observed for Cd and Zn (the most mobile metals) when chloride was present in the sediments. Characterisation of the sediments and of the pseudo-total metal contents by means of an aqua regia extraction was also assessed.

Quantitative assessment of the effects of agricultural practices designed to reduce 137Cs and 90Sr soil-plant transfer in meadows.

Agricultural practices (ploughing and reseeding, addition of lime and fertiliser) were tested as a feasible remediation strategy to reduce 137Cs (RCs) and 90Sr (RSr) soil-plant transfer in natural meadows in areas affected by the Chernobyl fallout. Field experiments were carried out for 2 years at six sites, covering dry and wet meadows. Observed results at field scale showed that ploughing plus reseeding provoked the main reduction in RSr transfer, with no further reduction after liming, while ploughing + reseeding + K fertiliser led to the maximum decrease in RCs transfer at most sites. The direct effects of agricultural practices on the exchange complex and soil solution composition were quantified by subsequent soil analyses. At the doses applied, lime did not affect the Ca + Mg concentrations in the exchange complex and soil solution of the ploughed soils, thus suggesting that the decrease in RSr transfer on treated plots was mainly due to the changes in the plant species after reseeding. With respect to RCs, changes in the K+NH4+ concentrations in the exchange complex and soil solution were consistent with changes in soil-plant transfer. Finally, RSr and RCs soil-plant transfer in ploughed plots was well predicted from soil properties, such as the solid-liquid distribution coefficient, the ionic composition of the soil solution and the exchangeable cations, with Pearson correlation coefficients of 0.98 and 0.86, respectively, between calculated and experimental log transfer factors.

Use of sorption and extraction tests to predict the dynamics of the interaction of trace elements in agricultural soils contaminated by a mine tailing accident.

Over 2000 ha of agricultural soils were contaminated by a pyritic sludge and acidic waste waters coming from a spill from a mining exploitation. The affected soils were acidic with sandy-loam texture (SL), loamy with neutral pH (L), and calcareous, saline, with clay texture (Cs). The Cs soils were contaminated only with acidic waste waters. Sorption and extraction tests were applied to examine the medium-term dynamics of the interaction of trace elements (As, Cd, Cu, Pb and Zn) in the soils. The solid-soil solution distribution coefficient (KD) was determined in soil samples taken 3 months (initial stage, 3M samples) and then nearly 2 years (final stage, 21M samples) after the accident. Distribution coefficient values ranged from the lowest values in the SL samples (from 0.2 l kg(-1) for Cd and Zn to 25 l kg(-1) for As) to higher values in the L and Cs soils. Lead and As had the highest KD in all soils (over 10(5) l kg(-1) in the L soils). No clear dynamics pattern could be derived from these data because of the low heavy metal concentrations in the soil solution. As a complementary approach, four single extractions (0.01 and 1 mol l(-1) CaCl2; 0.05 mol l(-1) EDTA; 0.43 mol l(-1) CH3COOH) were applied to soil and sludge samples. Samples derived from submitting field 3M samples to drying-wetting (DW) cycles were included to define a complete laboratory approach to predict field dynamics. Results from extraction tests indicated that changes of the trace element interaction over time depended on the soil pH and on the source of contamination. For those soils affected only by the acidic waste waters, where an increase in fixation occurred, natural processes such as diffusion controlled dynamics. For those soils contaminated by a mixed source, the dynamics of the interaction was the resultant process of the combination of the natural attenuation and the oxidation of the pyritic sludge. This latter process led to an increase in the remobilization for those elements associated with soluble secondary minerals (Cd and Zn) and to an increase in the fixation for those elements coprecipitating with insoluble secondary minerals (Pb and As). Drying-wetting cycles were useful to predict the dynamics in the field at month-year scale. The CH3COOH was recommended as the best test among those studied here to derive conclusions about dynamics pattern because it provided significant desorption yields in most scenarios. Acidic soils with sludge contamination represented the scenarios with the highest risk, while calcareous soils better attenuated contamination. In a longer time scale, the depletion of calcareous components needs to be controlled.

Assessment of metal mobility in dredged harbour sediments from Barcelona, Spain.

In order to assess heavy metal mobility in dredged harbour sediments, six superficial sediment samples covering a range of pollution levels and environments were collected in Barcelona Harbour. Samples were characterised in terms of major compounds (Al, Ca, Fe, Mn, Si, Ti, Mg, K and Na); total C, N and S contents; organic matter; and water content. Pseudo-total trace metal contents were assessed after aqua regia digestion (ISO 11466:1995). The modified BCR three-step sequential extraction procedure (BCR-SEP) was applied, and both major compounds (Al, Ca, Fe and Mn) and trace metals (Cd, Cr, Cu, Ni, Pb and Zn) were determined in the different extracts. Both the pseudo-total digestion method and the BCR-SEP were validated using two sediment certified materials from lakes (BCR CRM 701 and BCR CRM 601). The highest metal concentrations were observed in one of the sampling points which receives an urban discharge. The observed mobility order (percentage of metal extracted in the first step) of the six trace metals studied was Cd>Zn>Pb>Cu>Ni>Cr. The good agreement observed with the results obtained as the sum of the four steps (extractable+residue) and the pseudo-total content shows that laboratory working conditions were under control.