Comparison of surface micro-roughness and adaptation of titanium and cobalt chrome implant abutment fabricated by selective laser melting and conventional techniques.

PURPOSE: The objective of this study was to assess the surface micro-roughness and abutment adaptation of selective laser melting (SLM) implant abutments in comparison to cast and machined implant abutments. METHODS: Forty abutment specimens were divided equally into four groups according to the fabrication technique as follows (n = 10), Machined Ti alloy abutments (Control), Cast CoCr abutments, SLM-CoCr abutments, and SLM-Ti alloy abutments. Forty internal connection implants (Ø 4.0 ×10 mm, Superline™, Dentium Co., Seoul, Korea) were mounted in clear acrylic resin. Fabricated abutments were assessed for surface micro-roughness using a 3D optical noncontact surface microscope. Vertical and horizontal adaptation of the abutment with implant interface was assessed by using Bruker micro-CT. Data was assessed using analysis of variance and Tukey post hoc comparison tests for all the variables except vertical misfit was assessed using Kruskal-Wallis test. Pearson correlation was used to assess dependence between independent variable (surface roughness) and dependent variables (Horizontal misfit and vertical misfit). RESULTS: SLM-Ti abutments showed significantly rougher surface (p < 0.05) among the study groups. While SLM-CoCr abutments were smoother than Cast abutments with mean Ra of 1.30 ± 0.11 and 1.58 ± 0.17 µm, respectively (p < 0.05). For abutment adaptation, SLM-Ti abutments showed the highest horizontal misfit among the groups (p < 0.05). While, SLM-CoCr abutments (29.24 ± 11.11 µm) showed comparable (p > 0.05) horizontal misfit results with Cast (26.08 ± 3.93 µm) and machined (26.45 ± 7.33 µm) abutments. Comparable (p > 0.05) vertical misfit values between Cast CoCr (487.01 ± 40.34 µm), SLM-CoCr (358.38 ± 114.93 µm) and SLM-Ti (299.85 ± 172.88 µm) abutments were observed. A positive correlation was found between the surface roughness of the mating surfaces and abutment adaptation. CONCLUSION: SLM CoCr abutments exhibited low roughness and comparable abutment adaptation (vertically and horizontally) than cast (control) abutments. Therefore, SLM CoCr abutments should be clinically investigated as potential implant abutments for clinical use.

Effect of trialkoxysilane/aminosilane-containing universal adhesive on resin-ceramic microtensile bond strength and ceramic wettability: An in-vitro study.

Background: The dual-silane (trialkoxysilane/aminosilane) universal adhesive (UA) is claimed for its enhanced priming capacity of glass-ceramics. Objective: This study evaluated the effect of organofunctional trialkoxysilane- and organofunctional trialkoxysilane/aminosilane-containing UAs on the long-term resin-ceramic microtensile bond strength (µTBS) and wettability of ceramic. Methods: Hydrofluoric acid-etched lithium disilicate discs were distributed into four groups as follows: (control), no priming was performed; (MBN), primed using a silane-based primer (Monobond N); (SBU), primed using a trialkoxysilane-containing UA (Single Bond Universal Adhesive) and (SBP), primed using a trialkoxysilane/aminosilane-containing UA (Scotchbond Universal Plus Adhesive). Ceramic discs were cemented into blocks then sectioned into microbeams stored in distilled water at 37° for 1 year. The µTBS was evaluated followed by assessment of the failure modes. The contact angle of the two UAs was measured with a goniometer using the sessile drop technique. Results: MBN significantly improved the resin-ceramic µTBS (31.71 ± 6.33 MPa) compared to the control group. The resin-ceramic µTBS obtained after priming using SBP (22.83 ± 3.42 MPa) was comparable to those of MBN. SBU showed significantly inferior resin-ceramic µTBS (16.02 ± 6.28 MPa) compared with MBN. Mixed failures mode patterns were the most frequent in the groups. The ceramic wettability of both UAs did not significantly differ. Conclusion: Ceramic priming using a UA with dual-silane monomers (organofunctional trialkoxysilane/aminosilane) resulted in long-term adhesion comparable to a silane-containing primer. Incorporating aminosilane monomer in UA formulation did not affect the wetting of characteristics of the UA solution and enhanced its glass-ceramic priming capacity. Clinical significance: The use of UA with optimized silane content as a primer for glass-ceramics simplifies clinical adhesive procedures including resin cementation and repair of ceramic restorations.

Development of Artificial Intelligence Models for Tooth Numbering and Detection: A Systematic Review.

Dental radiography is widely used in dental practices and offers a valuable resource for the development of AI technology. Consequently, many researchers have been drawn to explore its application in different areas. The current systematic review was undertaken to critically appraise developments and performance of artificial intelligence (AI) models designed for tooth numbering and detection using dento-maxillofacial radiographic images. In order to maintain the integrity of their methodology, the authors of this systematic review followed the diagnostic test accuracy criteria outlined in PRISMA-DTA. Electronic search was done by navigating through various databases such as PubMed, Scopus, Embase, Cochrane, Web of Science, Google Scholar, and the Saudi Digital Library for the articles published from 2018 to 2023. Sixteen articles that met the inclusion exclusion criteria were subjected to risk of bias assessment using QUADAS-2 and certainty of evidence was assessed using GRADE approach.AI technology has been mainly applied for automated tooth detection and numbering, to detect teeth in CBCT images, to identify dental treatment patterns and approaches. The AI models utilised in the studies included exhibited a highest precision of 99.4% for tooth detection and 98% for tooth numbering. The use of AI as a supplementary diagnostic tool in the field of dental radiology holds great potential.

Factors Influencing Dentists' Choice of Restorative Materials for Single-Tooth Crowns: A Survey Among Saudi Practitioners.

BACKGROUND Material selection is crucial in restorative dentistry, influenced by aesthetics, material properties, and tooth location. This understanding is key for advancing dental practices and patient outcomes. The present study aimed to assess dentists' preferences for restorative materials in single-tooth crowns (SC) and how abutment tooth location and preparation margins influence these choices. MATERIAL AND METHODS A web-based pre-validated questionnaire survey was conducted among 811 actively practicing dentists in Saudi Arabia. RESULTS In posterior teeth, we found that ceramic was the most preferred material for SC regardless of the abutment tooth location and location of margins, followed by porcelain fused to metal (PFMs). In anterior teeth, ceramics were preferred, followed by CAD/CAM-based resin SC. Among the choice of ceramics in teeth for both supra-gingival margins, monolith zirconia was the most-preferred material for SC fabrication in posterior teeth, followed by zirconia-reinforced lithium silicate ceramic. Similarly, for sub-gingival margins, monolith zirconia crowns were the most popular option in posterior teeth among the respondents, with the highest in the mandibular molar region. In the anterior region, layered zirconia was the least preferred, and lithium disilicate ceramics was the most-favored option. A statistically significant difference existed between supra- and subgingival preparation for teeth 11 (P=0.01), 16 (P=0.03), and 34 (P=0.02). CONCLUSIONS Ceramic was the material of choice among Saudi dentists for replacement of SC, irrespective of the location and preparation margin. Monolith zirconia was usually selected for posterior teeth and lithium disilicate ceramics was the top choice in anterior teeth.

Clinical and radiographic outcomes of adjunctive photodynamic therapy for treating peri-implantitis among diabetics and cigarette smokers: a systematic review of randomized controlled trials.

Photodynamic therapy (PDT) has been suggested as an adjunctive therapeutic approach for peri-implantitis. This systematic review aimed to assess the clinical and radiographic outcomes of adjunctive PDT (aPDT) for the treatment of peri-implantitis among diabetics and cigarette smokers. Randomized controlled trials (RCTs), which assessed the clinical and radiographic outcomes of aPDT versus other intervention(s) and/or MD alone among diabetics and smokers with peri-implantitis, were considered eligible for the review. Meta-analysis was performed for calculating the standard mean difference (SMD) with a 95% confidence interval (CI). The methodological quality of the included studies was evaluated using the modified Jadad quality scale. The meta-analysis revealed no significant differences between the influence of aPDT and other intervention/MD alone on the peri-implant PI among diabetics at the final follow-up. However, statistically significant improvements in the peri-implant PD, BOP, and CBL were observed after the application of aPDT among diabetics. Similarly, no significant differences were found between the influence of aPDT and other interventions/MD alone on the peri-implant PD among smokers with peri-implant diseases at the final follow-up. However, statistically significant improvements in the peri-implant PI, BOP, and CBL were observed after the application of aPDT among smokers. Significant improvements in the peri-implant PD, BOP, and CBL among diabetics and the peri-implant PI, BOP, and CBL among smokers after the application of aPDT at the final follow-up. However, large-scale, well-designed, and long-term RCTs are recommended in this domain.

Incorporation of Zirconium Oxide Nanoparticles in Adhesive Resin for Bonding of Brackets to Enamel Conditioned with Er,Cr:YSGG, Photodynamic Therapy, and Phosphoric Acid.

Objective: To evaluate the effect of enamel conditioning methods, that is, total-etch and rinse (TER), Er,Cr:YSGG (ECYL), and photodynamic therapy (PDT) on the shear bond strength (SBS) of orthodontic metallic brackets bonded using Zirconium oxide experimental adhesive (ZOEA). Methods: Sixty human incisor buccal surfaces were cleaned and allocated into three groups based on the method of enamel surface treatment, that is, TER using 37% phosphoric acid gel, methylene blue photosensitizer activated by PDT and ECYL (n = 20 each). Each group was further divided into two subgroups (n = 10) based on the type of adhesive, that is, ZOEA and experimental adhesive (EA). Metallic brackets were seated using composite resin. Samples were placed in a universal testing machine for SBS and failure mode using the ARI index. One-way analysis of variance and post hoc Tukey were used for multiple comparisons. ARI was presented in percentages in different investigated groups. Results: TER+ZOEA (17.16 ± 0.41 MPa) displayed the highest bond integrity. However, group PDT+EA (11.34 ± 0.25 MPa) demonstrated the lowest bond scores. The intergroup comparison revealed that the TER system displayed significantly higher SBS values than the PDT and ECYL groups (p < 0.05). The intragroup comparison revealed that enamel conditioned with TER and brackets bonded with ZOEA and EA displayed comparable bond integrity (p > 0.05). Conclusions: Enamel conditioned with TER bonded to a metallic bracket displayed better bond strength than PDT and ECYL. Zirconium oxide nanoparticles incorporated in adhesive have proved to be promising in improving the bond integrity of adhesive.

Influence of surface treatment on repair bond strength of CAD/CAM long-term provisional restorative materials: an in vitro study.

BACKGROUND: The surface treatment to improve the repair bond strength may vary because CAD/CAM provisional restoration polymers exhibit a variety of microstructures. This study was conducted to evaluate the effect of surface treatments on the repairability of three different CAD/CAM polymers for long-term provisional restorations. METHODS: Thirty specimens from each provisional restorative materials (CAD-Temp, Everest C-Temp, and PEEK) were divided into three groups: C: surfaces received no treatment; SB: surfaces were airborne particle abraded with 50 µm aluminum oxide; SB-T: surfaces received the same conditions as group SB in addition to thermocycling before and after treatment. Primer and nanohybrid repair resin composite were applied to the prepared CAD /CAM surfaces. The shear bond strength and the mode of failure were assessed. ANOVA and Tukey's significant difference tests were used to evaluate the data. RESULTS: The SB group had significantly higher repair SBS values (p < .001) compared to the other groups (C and SB-T). Everest C-Temp significantly recorded the highest repair SBS (17.84 ± 0.19 MPa) in group SB, while the lowest repair SBS values (5.51 ± 1.14 MPa) for CAD-Temp were recorded in group C. PEEK significantly recorded the second highest repair SBS (15.96 ± 0.18) in the SB group. CONCLUSIONS: Everest C-Temp had the highest repair SBS after an airborne abrasion particle. Thermocycling had no significant effect on the repair SBS for PEEK. Everest C-Temp and PEEK are recommended as long-term durable provisional materials for clinical use.

No-Cap Flowable Bulk-Fill Composite: Physico-Mechanical Assessment.

(1) Background: A newer class of flowable bulk-fill resin-based composite (BF-RBC) materials requires no capping layer (Palfique Bulk flow, PaBF, Tokuyama Dental, Tokyo, Japan). The objective of this study was to assess the flexural strength, microhardness, surface roughness, and color stability of PaBF compared to two BF-RBCs with different consistencies. (2) Methods: PaBF, SDR Flow composite (SDRf: Charlotte, NC, USA) and One Bulk fill (OneBF: 3M, St. Paul, MN, USA) were evaluated for flexural strength with a universal testing machine, surface microhardness using a pyramidal Vickers indenter, and surface roughness using a high-resolution three-dimensional non-contact optical profiler, a and clinical spectrophotometer to measure the color stability of each BF-RBC material. (3) Results: OneBF presented statistically higher flexural strength and microhardness than PaBF or SDRf. Both PaBF and SDRf presented significantly less surface roughness compared with OneBF. Water storage significantly reduced the flexural strength and increased the surface roughness of all tested materials. Only SDRf showed significant color change after water storage. (4) Conclusions: The physico-mechanical properties of PaBF do not support its use without a capping layer in the stress bearing areas. PaBF showed less flexural strength compared with OneBF. Therefore, its use should be limited to a small restoration with minimal occlusal stresses.

Different Designs of Deep Marginal Elevation and Its Influence on Fracture Resistance of Teeth with Monolith Zirconia Full-Contour Crowns.

Background and objectives: Even with the demand for high esthetics, the strength of the material for esthetic applications continues to be important. In this study, monolith zirconia (MZi) crowns fabricated using CAD/CAM were tested for fracture resistance (FR) in teeth with class II cavity designs with varying proximal depths, restored through a deep marginal elevation technique (DME). Materials and Methods: Forty premolars were randomly divided into four groups of ten teeth. In Group A, tooth preparation was conducted and MZi crowns were fabricated. In Group B, mesio-occluso-distal (MOD) cavities were prepared and restored with microhybrid composites before tooth preparation and the fabrication of MZi crowns. In Groups C and D, MOD cavities were prepared, differentiated by the depth of the gingival seat, 2 mm and 4 mm below the cemento-enamel junction (CEJ). Microhybrid composite resin was used for DME on the CEJ and for the restoration of the MOD cavities; beforehand, tooth preparations were conducted and MZi crowns were and cemented using resin cement. The maximum load to fracture (in newtons (N)) and FR (in megapascals (MPa)) were measured using the universal testing machine. Results: The average scores indicate a gradual decrease in the load required to fracture the samples from Groups A to D, with mean values of 3415.61 N, 2494.11 N, 2108.25 N and 1891.95 N, respectively. ANOVA revealed highly significant differences between the groups. Multiple group comparisons using the Tukey HSD post hoc test revealed that Group D had greater DME depths and showed significant differences compared with Group B. Conclusions: FR in teeth decreased when more tooth structure was involved, even with MZi crowns. However, DME up to 2 mm below the CEJ did not negatively influence the FR. Strengthening the DME-treated teeth with MZi crowns could be a reasonable clinical option, as the force required to fracture the samples far exceeded the maximum recorded biting force for posterior teeth.

Novel 1,2-Bismethacrylate-3-Eugenyl Propane for Resin Composites: Synthesis, Characterization, Rheological, and Degree of Conversion.

This work aimed to synthesize a novel dimethacrylated-derivative of eugenol (Eg) (termed EgGAA) as potential biomaterial for certain applications such as dental fillings and adhesives. EgGAA was synthesized through a two-step reaction: (i) a mono methacrylated-eugenol (EgGMA) was produced via a ring-opening etherification of glycidyl methacrylate (GMA) with Eg; (ii) EgGMA was condensed with methacryloyl chloride into EgGAA. EgGAA was further incorporated in matrices containing BisGMA and TEGDMA (50:50 wt%) (TBEa), in which EgGAA replaced BisGMA as 0-100 wt% to get a series of unfilled resin composites (TBEa0-TBEa100), and by addition of reinforcing silica (66 wt%), a series of filled resins were also obtained (F-TBEa0-F-TBEa100). Synthesized monomers were analyzed for their structural, spectral, and thermal properties using FTIR, 1H- and 13C-NMR, mass spectrometry, TGA, and DSC. Composites rheological and DC were analyzed. The viscosity (η, Pa·s) of EgGAA (0.379) was 1533 times lower than BisGMA (581.0) and 125 times higher than TEGDMA (0.003). Rheology of unfilled resins (TBEa) indicated Newtonian fluids, with viscosity decreased from 0.164 Pa·s (TBEa0) to 0.010 Pa·s (TBEa100) when EgGAA totally replaced BisGMA. However, composites showed non-Newtonian and shear-thinning behavior, with complex viscosity (η*) being shear-independent at high angular frequencies (10-100 rad/s). The loss factor crossover points were at 45.6, 20.3, 20.4, and 25.6 rad/s, indicating a higher elastic portion for EgGAA-free composite. The DC was insignificantly decreased from 61.22% for the control to 59.85% and 59.50% for F-TBEa25 and F-TBEa50, respectively, while the difference became significant when EgGAA totally replaced BisGMA (F-TBEa100, DC = 52.54%). Accordingly, these properties could encourage further investigation of Eg-containing resin-based composite as filling materials in terms of their physicochemical, mechanical, and biological potentiality as dental material.

Levels of peri-implant sulcular fluid levels of soluble urokinase plasminogen activator receptor and TNF-α among cigarette smokers and non-smokers with peri-implantitis.

BACKGROUND: Soluble urokinase plasminogen activator receptor (suPAR) and tumor necrosis factor-alpha (TNF-α) are inflammatory biomarkers. No studies have yet assessed the suPAR levels in relation with TNF-α in the peri-implant sulcular fluid (PISF) among cigarette smokers and non-smokers with peri-implantitis. OBJECTIVE: The aim was to evaluate PISF levels of suPAR, and TNF-α among cigarette smokers and non-smokers with and without peri-implantitis. METHODS: Sixty male patients with peri-implantitis were included. There were 20 cigarette smokers and 20 and non-smokers with peri-implantitis (Groups 1 and 2), and 20 non-smokers without peri-implantitis (Group 3). Demographic data and information related to cigarette smoking was recorded. Peri-implant clinicoradiographic parameters (plaque index [PI], gingival index [GI], probing depth [PD] and crestal bone loss [CBL]) were assessed. The PISF samples were collected and levels of suPAR and TNF-α were measured. Sample-size estimation was performed and all parameters were statistically assessed. Level of significance was set at P< 0.05. RESULTS: Sixty individuals were included in Groups 1, 2 and 3 (20 in each). Peri-implant PI (P< 0.01), PD (P< 0.01) and mesial (P< 0.01) and distal (P< 0.01) CBL were significantly higher in Group 1 than in Groups 2 and 3. The PISF volume (P< 0.01) and suPAR (P< 0.01) and TNF-α levels (P< 0.01) were significantly higher in Groups 1 and 2 than in Group 3. There was no difference in PISF volume and suPAR and TNF-α levels between patients in Groups 1 and 2. In Group 2, there was a statistically significant correlation between peri-implant PD and PISF suPAR and TNF-α levels (P< 0.01). The suPAR and TNF-α levels are expressed in high concentrations in the PISF of smokers and non-smokers with peri-implantitis compared with non-smokers without peri-implantitis. CONCLUSION: In non-smokers, PISF suPAR and TNF-α levels are correlated with peri-implant PD.

National Survey on Silver Diamine Fluoride (SDF) Awareness, Knowledge, Attitude, and Use among General Dental Practitioners in the Kingdom of Saudi Arabia-An Exploratory Survey.

Silver diamine fluoride (SDF) has been accepted as an appropriate alternative for caries management. However, knowledge and utilization of SDF among dentists vary considerably. The authors in the present study aimed to assess the awareness, knowledge, attitudes, and use of SDF among general dentists (GD) in Saudi Arabia and to correlate the differences based on the different regions and experience levels of the dentists. In this regard, a cross-sectional web-based questionnaire was conducted, and a response was received from 311 GDs from different parts of the country. Information regarding demographic data, knowledge, attitudes, use, and barriers to SDF in dentists' professional lives were elicited. The mean age of the participants (55.3%) was between 25-35 years. Most (92.45%) of the dentists were aware of the material and (61%) agreed that SDF could arrest carious lesions. More than half of the dentists agreed/strongly agreed that SDF was a good treatment alternative for restorations in children with behavioral issues (63.1%), medically fragile patients (53.7%), patients with severe anxiety (64.5%), patients who underwent radiation or chemotherapy (47.3%), and patients needing general anesthesia for dental treatment (74%). Comparative evaluation using ANOVA revealed regional differences based on knowledge, attitudes, and use. Tukey HSD further highlighted that the practitioners in the western region are more knowledgeable regarding its benefits and utilize it more frequently in their practice compared to other regions. On the other hand, the experience level of the GDs did not have any impact on their knowledge, attitudes, and use of SDF.

Evaluation of Effects of Various Irrigating Solutions on Chemical Structure of Root Canal Dentin Using FTIR, SEM, and EDS: An In Vitro Study.

Background: Sequential chemical application for irrigating a root canal during chemomechanical debridement can affect the dentin microstructure. Understanding the effects of various irrigants on chemical properties of dentin can elucidate their effects on physical properties and thereby explain the higher incidence of structural failure in endodontically treated teeth. This in vitro research aimed to compare and evaluate the effects of three different irrigating solutions on the chemical structure of root canal dentin in extracted human teeth. Methods: Forty-eight extracted single-rooted mandibular premolar teeth were sectioned at the cemento−enamel junction by a diamond disc and were then randomly assigned to four groups of twelve samples each. The groups were irrigated using 5.25% NaOCl, ozonated olive oil, silver citrate, or distilled water. Dentin sections measuring 1.5 mm were obtained from the root portion and each section and were analyzed using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and electron-dispersive spectroscopy (EDS). FTIR and EDS values are reported as means ± standard deviations. Data were analyzed using an ANOVA and a post hoc Bonferroni test (p < 0.05). Results: A comparison of the FTIR and EDS values among the groups using ANOVA revealed statistically significant differences in the organic and inorganic peak values among the groups. An intergroup comparison between NaOCl with silver citrate and ozonated olive oil revealed significant reductions in the carbonate and phosphate peak values in the NaOCl group (p < 0.05). The EDS values tabulated for the carbon, oxygen, phosphorous, and calcium peak levels showed significant differences between the groups using an ANOVA. An SEM analysis was conducted under 1500× magnification, which revealed smear layer removal in the silver citrate group. Conclusions: The silver citrate solution and the ozonated olive oil caused less changes in the organic and mineral contents of dentin than sodium hypochlorite.

Comparison of Tensile Bond Strength of Fixed-Fixed Versus Cantilever Single- and Double-Abutted Resin-Bonded Bridges Dental Prosthesis.

Resin-bonded fixed dental prostheses (RBFDP) are minimally invasive alternatives to traditional full-coverage fixed partial dentures as they rely on resin cements for retention. This study compared and evaluated the tensile bond strength of three different resin-bonded bridge designs, namely, three-unit fixed-fixed, two-unit cantilever single abutment, and three-unit cantilever double-abutted resin-bonded bridge. Furthermore, the study attempted to compare the tensile bond strengths of the Maryland and Rochette types of resin-bonded bridges. Based on the inclusion and exclusion criteria, a total of seventy-five extracted maxillary incisors were collected and later were mounted on the acrylic blocks. Three distinct resin-bonded metal frameworks were designed: three-unit fixed-fixed (n = 30), two-unit cantilever single abutment (n = 30), and a three-unit cantilever double abutment (n = 30). The main groups were further divided into two subgroups based on the retainer design such as Rochette and Maryland. The different prosthesis designs were cemented to the prepared teeth. Later, abutment preparations were made on all specimens keeping the preparation as minimally invasive and esthetic oriented. Impression of the preparations were made using polyvinyl siloxane impression material, followed by pouring cast using die stone. A U-shaped handle of 1.5 mm diameter sprue wax with a 3 mm hole in between was attached to the occlusal surface of each pattern. The wax patterns were sprued and cast in a cobalt-chromium alloy. The castings were cleaned by sandblasting, followed by finishing and polishing. Lastly, based on the study group, specimens for Rochette bridge were perforated to provide mechanical retention between resin cement and metal, whereas the remaining 15 specimens were sandblasted on the palatal side to provide mechanical retention (Maryland bridge). In order to evaluate the tensile bond strength, the specimens were subjected to tensile forces on a universal testing machine with a uniform crosshead speed. The fixed-fixed partial prosthesis proved superior to both cantilever designs, whereas the single abutment cantilever design showed the lowest tensile bond strength. Maryland bridges uniformly showed higher bond strengths across all framework designs. Within the limitations of this study, the three-unit fixed-fixed design and Maryland bridges had greater bond strengths, implying that they may demonstrate lower clinical failure than cantilever designs and Rochette bridges.

Evaluation of Fluoride Release in Chitosan-Modified Glass Ionomer Cements.

OBJECTIVE: This study assessed the influence of chitosan nanoparticles on the fluoride-releasing ability of 4 glass ionomer cement (GIC) through an in vitro analysis. METHODS: Four types of GIC (type II light cure universal restorative, type II universal restorative, GC Fuji VII, and type IX) were modified with nanochitosan particles; 10% chitosan was added to the glass ionomer liquid. Six specimens for each of the 4 groups were created, using expendable Teflon moulds. Discs of each type of GIC (n = 6) were immersed in deionised water at various time intervals. Electrodes selective for fluoride ions were employed to analyse the amount of released fluoride at 1, 7, 14, 21, and 28 days. RESULTS: Chitosan-modified GICs showed greater fluoride release than conventional GICs at all time points. All samples showed an initial high release of fluoride that tapered off with time. The total amount of fluoride released increased from the 1st day to the 28th day on adding chitosan to all the 4 types of GIC. Amongst those, type IX high-strength posterior extra with chitosan released a considerably higher quantity of fluoride at all time intervals. CONCLUSIONS: In all the experimental groups, adding chitosan to the glass ionomer liquid had an accelerating effect on its fluoride-releasing property.

Comparative Evaluation of Microleakage of Flowable Composite Resin Using Etch and Rinse, Self-Etch Adhesive Systems, and Self-Adhesive Flowable Composite Resin in Class V Cavities: Confocal Laser Microscopic Study.

The essential factor in determining the preservation of restoration is the marginal seal. Restoring cervical lesions with a resin composite has always been a challenge. Composite resins with various viscosities and different bonding systems are being researched to reduce the microleakage. Confocal laser scanning microscopy (CLSM) is the latest non-destructive technique for visualizing the microleakage. Objectives: To evaluate and compare the microleakage of Universal Flo composite resin (G-aenial) using etch and rinse adhesive system ER-2 steps (Adper Single Bond 2), self-etch adhesive system SE-1 step (G-Bond), and self-adhesive flowable composite resin (Constic) in Class V cavities using a confocal laser scanning microscope. Materials and Method: Class V cavities were prepared on 27 caries-free human extracted premolar teeth on the buccal and lingual surfaces with standardized dimensions of 2 mm height, width 4 mm, and a depth of 2 mm. After the cavity preparation, all teeth were randomly divided into three groups, namely Group-I: G-aenial Universal Flo with Single Bond 2 (n = 9 teeth); Group-II: G- aenial Universal Flo with G-Bond (n = 9 teeth), and Group-III: Constic (n = 9 teeth). The prepared and restored specimens were then subjected to thermocycling for 500 cycles in a water bath at 5 °C and 55 °C with a dwelling time of 30 s. The specimens were placed in 0.6% aqueous rhodamine dye for 48 h. Sectioning was carried out bucco-lingually and specimens were evaluated for microleakage under a confocal laser scanning microscope. Results: There was a significant difference (p = 0.009) in microleakage when comparing total etch and rinse, specifically between Adper Single Bond 2 ER-2 steps (fifth generation) and self-adhesive flowable composite resin, which is Constic. There was more microleakage in the self-etch bonding agent, particularly G-Bond, SE-1 step (seventh generation), when compared to ER-2 steps (fifth generation bonding agent); however, the results were not statistically significant (p = 0.468). The self-adhesive flowable composite resin showed more microleakage than SE-1 step and ER-2 steps. Conclusions: None of the adhesive systems tested were free from microleakage. However, less microleakage was observed in the total etch and rinse, especially Adper Single Bond 2 (ER-2 steps), than the self-etch adhesive system SE-1 step and self-adhesive flowable composite resin. Clinical significance: Constant research and technological advancements are taking place in dentin adhesives to improve the marginal seal. This has led to the evolution of total acid-etching dentin bonding agents termed as etch and rinse (ER)-2 steps (fifth generation dentin bonding agents) and self-etching (SE) 2 steps, and SE-1 step dentin bonding agents termed as the sixth and seventh generation bonding agents, respectively.

Assessment of Knowledge and Attitude of Dental Students towards HIV and Its Oral Manifestations in Saudi Arabia-A Cross-Sectional Study.

BACKGROUND: It is essential for practicing dentists to have adequate knowledge of HIV/AIDS and its implications in the dental practice. Their attitudes should also be up to the professional expectations. This study aimed to assess knowledge of HIV/AIDS infection and attitudes towards its patients among dental students in Saudi Arabia. METHODS: A questionnaire was prepared and distributed among a sample of dental students in Saudi Arabia. Twenty questions related to knowledge, attitudes, and oral manifestation of HIV were presented. RESULTS: A total of 405 questionnaires were completed (67% response rate). Participants showed low knowledge of safety regarding HIV (39.5%) and 44.2% indicated that they would take an HIV test after needle stick injury. The proportion of correct answers regarding transmission of HIV through saliva, cardiopulmonary resuscitation, and aerosols by hand pieces was 41%, 37.5%, and 26.4%, respectively. Almost 50% of the surveyed dental students expressed unwillingness to treat HIV-positive patients. Poor knowledge was noted regarding oral manifestations of HIV (32.7%). Of the participants, 57.8% indicated that infection control procedures are very important for the treatment of HIV patients and 50.6% believed that a dentist can make a decision to reject the treatment of HIV patients. According to the participating dental students, the three major oral manifestations in HIV patients are hairy leukoplakia (47.4%), oral candidiasis (44.7%), and Kaposi's sarcoma (43.5%). CONCLUSION: Inadequate knowledge and unprofessional attitude towards HIV/AIDS patients were identified among this group of dental students in Saudi Arabia. Dental educators and health care planners in Saudi Arabia should plan to promote the knowledge and attitudes of dental students in Saudi Arabia towards the treatment of HIV patients.

A Prospective Clinical Study Evaluating the Efficacy of Intra-Ligamentary Anesthetic Solutions in Mandibular Molars Diagnosed as Symptomatic Irreversible Pulpitis with Symptomatic Apical Periodontitis.

Accomplishing painless endodontic treatment, especially in the mandibular molar region, is challenging. Hence, the aim of the study was to compare the efficacy of 2% lidocaine and 4% articaine when used as supplemental intra-ligamentary (IL) anesthesia in mandibular molars having symptomatic irreversible pulpitis with symptomatic apical periodontitis after failed Inferior Alveolar Nerve Block (IANB) injection. In this prospective study, one-hundred and forty-seven adult patients diagnosed with irreversible pulpitis in a mandibular tooth were included who received IANB with 1.8 mL of 2% lidocaine with 1:100,000 epinephrine. Patients who experienced pain were recorded using the Heft-Parker visual analog scale (HP-VAS score ≥ 55 mm) and received supplement intra-ligament injection with either4% articaine or 2% lidocaine with 1:100,000 epinephrine. Supplementary intra-ligament injections resulted in 82.6% and 91.3% of profound anesthesia in the first molar region for 2% lidocaine and 4% articaine, respectively. Similarly, an additional IL injection of articaine success percent (78.9%) in the second molar region was higher than lidocaine (63.1%). The overall success ratio revealed no significant difference in achieving profound anesthesia of either solution. In this study population, there was no difference in the success ratio of anesthesia between 2% lidocaine and 4% articaine when used as supplemental IL injection.

Herbal Agents versus Ethylene Diamine Tetra Acetic Acid on Removal of the Smear Layer-A Systematic Review of In Vitro Studies.

This systematic review aimed to compare the efficacy of herbal agents with ethylene diamine tetraacetic acid (EDTA) in removing the smear layer during root canal instrumentation. The research question in the present study was to assess: "Is there a significant difference in reducing smear layer comparing EDTA and herbal agents?" Electronic databases (PubMed, Scopus, and Web of Science) were searched from their start dates to April 2022 using strict inclusion and exclusion criteria, and reviewed following PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) 2020 guidelines. Only in vitro studies comparing herbal agents with EDTA were included in the current systematic review. Two reviewers independently assessed the included articles. A total of 625 articles were obtained from an electronic database. Eighteen papers were included for review of the full text, out of which, ten papers were excluded because they did not meet the inclusion criteria. Finally, eight articles were included in the systematic review. The present systematic review considered only in vitro studies; hence, the result cannot be completely translated to strict clinical conditions. The results of the present systematic review have shown that quixabeira, morindacitrifolia, oregano extract, and neem show better smear layer removal compared to other herbal agents, whereas they showed reduced smear layer removal when compared with EDTA. Although, it was seen that most of the included studies did not report a high quality of evidence. Hence, the present systematic review concludes that herbal agents have reported to show inferior smear layer removal when compared to EDTA. Thus, as far as herbal based alternatives are concerned, there is no highest level of evidence to state its real benefit when used as a chelating root canal irrigant.