Alternative Ecosorbent for the Determination of Trihalomethanes in Aqueous Samples in SPME Mode.

A new sorbent material based on modified clay with ionic liquid immobilized into an agarose film was developed as part of this study. It was applied to determine organochlorine pollutants, like disinfection byproducts, through headspace solid-phase microextraction-gas chromatography-electron capture detection (HS-SPME-GC-ECD). The disinfection byproducts determined in this study were used as model molecules because they were volatile compounds, with proven severe effects on human health. Their presence in aquatic environments is in trace concentrations (from pg L-1 to mg L-1). They are classified as emergent pollutants and their determination is a challenge for analytical chemists. The parameters which affected the extraction efficiency, i.e., number and distance between SPME discs, salt concentration, the temperature of extraction, extraction time, and desorption time, were optimized. A wide linear dynamic range of 10-1000 ng mL-1 and coefficients of determination better than 0.997 were achieved. The limits of detection and the limits of quantitation were found in the ranges of (1.7-3.7) ng mL-1 and (5.6-9.9) ng mL-1, respectively. The precision, expressed as relative standard deviation (RSD), was better than 8%. The developed sorbent exhibits good adsorption affinity. The applicability of the proposed methodology for the analysis of trihalomethanes in environmental and water samples showed recoveries in the range of 86-95%. Finally, the newly created method fully complied with the principles of green chemistry. Due to the fact that the sorbent holder was made of agarose, which is a wholly biodegradable material, sorbent clay is a widespread material in nature. Moreover, the reagents intercalated into the montmorillonite are new green solvents, and during the whole procedure, low amounts of organic solvents were used.

Impact of polycyclic aromatic hydrocarbons in mangroves from the Colombian pacific coast: Evaluation in sediments and bivalves.

Bivalves and sediments were sampled from mangroves in the Pacific Coast of Colombia to evaluate the concentrations of the 16 polycyclic aromatic hydrocarbons (PAHs) prioritized by U.S.EPA. Mangroves are highly vulnerable to anthropogenic activities, such as oil spills, which affect sediments and the organisms that depend on that ecosystem. Twelve samples of mangrove and non-mangrove (sandy) sediments and 20 samples of Anadara tuberculosa from mangrove were collected in marine and estuarine areas. In sediments and A. tuberculosa, the highest concentration of Æ©16PAHs was found in estuarine mangroves close to the Rosario River mouth, ranging from 171.4 to 564.0 ng g-1 and 31.0 to 169.0 ng g-1, respectively. For the bivalve, the concentrations showed less variability than sediment, with 25% and 20% of bivalve samples exceeding the limits established by the European Regulatory Commission and Ministry of Health and Social Protection of Colombia, respectively, which can cause effects on people's health. The PAHs isomeric ratios determined in sediments indicated that these compounds were originated mainly from petrogenic sources. The PAHs profile reveals the dominance of 3 and 4 rings PAHs in sediments and dominance of 4 rings PAHs in bivalves.

Green method to determine triazine pesticides in water using Rotating Disk Sorptive Extraction (RDSE).

The following work presents the development of the solid phase extraction technique with rotary disk (RDSE) in which the analysis for seven triazines in surface waters was first implemented. All the variables involved in extraction have been studied and optimized using a solid phase of octadecyl (C18) deposited on surface of the disk. Triazines were analyzed quantitatively by gas chromatography with simple quadruple mass detector, recoveries obtained for seven triazines were between 80% and 120%, accuracy expressed as RSD was between 3.21% and 6.34%, and detection limit of the method was between 0.020-0.056 µgL-1 according to each analyte, which indicates a good reproducibility and precision of the method. Finally, the method was applied to analyze the objective compounds in water samples obtained in the Bolo River (Palmira-Colombia), in which triazines were not detected.

Multi-residue analysis of pesticides in blood plasma using hollow fiber solvent bar microextraction and gas chromatography with a flame ionization detector.

The challenges faced on pesticide extraction from biological samples are finding a method that allows a multi-residue extraction, pre-concentration, clean-up, and isolation of analytes in just one step. In this sense, the hollow fiber - liquid phase microextraction method (HF- LPME) in the "solvent bar" mode was used to optimize and validate a method for pesticide multi-residue analysis in blood plasma at trace levels, through gas chromatography coupled with a flame ionization detector (GC-FID). Hollow fiber solvent bar microextraction HF-SBME was carried out with octanol immobilized into the pores of hydrophobic polypropylene fiber and disposed within a matrix of blood plasma, spiked with a mixture of pesticides (monocrotophos, lindane, aldrin, methyl parathion, endosulfan, dieldrin, DDD, DDT, and endrin). The optimization parameters evaluated were: extraction temperature and time, stirring speed, and salt concentration. A principal component analysis was performed to visualize the analytes' behaviour based on their explained variance, and then, a Box-Behnken analysis was generated to identify the optimum parameters. According to the PCA, all pesticides showed similar responses to the extraction method and the response of dieldrin exhibit the lowest variance. Moreover, the stationary points selected from the Box-Behnken analysis were 25.5 °C for the extraction temperature, 870 rpm for stirring speed, 16 min for extraction time, and 8.3 % w/v of salt concentration. Moreover, the validation results proved that HF-SBME is an alternative technique for pesticide multi-residue extraction in blood plasma. The analytes were able to concentrate, reaching 46 fold enrichment. The solvent type, sample and solvent volume were narrowed down without changing the method's precision or accuracy. The relative standard deviation was under 10 %, and the recovery was between 55 % and 105 % for the different analytes excepting lindane, which had lower recovery (27 %). The detection limits were 0.02 until 0.13 µg mL-1 for most of the pesticides used. Finally, HF-SBME is a good alternative for pesticide multi-residue extraction in complex matrices like plasma.

A high throughput approach to rotating-disk sorptive extraction (RDSE) using laminar cork for the simultaneous determination of multiclass organic micro-pollutants in aqueous sample by GC-MS.

In this study, a high throughput approach to rotating-disk sorptive extraction (RDSE) using laminar cork as extraction phase is demonstrated for the first time in the determination of 20 multiclass organic micro-pollutants including pesticides, PAHs and UV filters compounds from aqueous samples with gas chromatography mass spectrometry (GC-MS). The influencing parameters (desorption solvent, volume and time, extraction time and sample pH and ionic strength) were carefully optimized using multivariate designs. The optimal conditions were 10 min for extraction using 35 mL of water samples and a liquid desorption using 1 mL of MeOH:AcOEt (50:50% v/v) for 20 min. A low-cost apparatus that allows six extractions simultaneously, providing a high throughput of 5 min per sample turnaround times, considering the sample preparation step was used for the first time in this modified RDSE methodology. Satisfactory analytical performance was achieved with limits of detection (LOD) between 0.08 and 1.5 µg L-1 and limits of quantification (LOQ) between 0.3 and 4.8 µg L-1. The relative recoveries for the analytes were determined using river and lake water samples spiked at different concentrations and ranging from 80% to 119% for all analytes, with relative standard deviations (RSD) lower than 20%. The extraction efficiency obtained for the proposed configuration with laminar cork was significantly superior to powdered cork, demonstrating an interesting new configuration for new applications.

Cork sheet as a sorptive phase to extract hormones from water by rotating-disk sorptive extraction (RDSE).

This work reports for the first time the use of laminar cork as a sorptive phase in a microextraction technique, rotating-disk sorptive extraction (RDSE). Typical hormones (estrone, estradiol, estriol and ethinyl estradiol) were selected as analyte models and extracted from wastewater samples on laminar cork with statistically equivalent extraction efficiency to that provided by Oasis HLB. The cork characterization was performed by confocal fluorescence microscopy (CLSM), Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM), allowing the identification of lignin, suberin and polysaccharides (cellulose and hemicellulose) as the main components of the cork. The best conditions for extraction were as follows: rotation velocity of the disk, 2000 rpm; extraction time, 45 min; and sample volume, 20 mL. The analytical features of the developed method show that calibration curves for all analytes have R2 values higher than 0.99. The absolute recoveries were higher than 63%, and the precision, expressed as relative standard deviation, ranged from 2 to 16%. The LOD and LOQ ranges were 3-19 and 10-62 ng L-1, respectively. The proposed method was applied to the analysis of wastewater, and the concentrations of hormones in a wastewater treatment plant in Santiago, Chile, ranged from

A green and simple sample preparation method to determine pesticides in rice using a combination of SPME and rotating disk sorption devices.

In this study, a novel environmentally-friendly approach was developed to overcome certain limitations in the analysis of solid food samples. An experimental setup based on solid-phase microextraction apparatus coupled to a rotating disk device is proposed for the determination of polar and slightly-polar pesticides including carbofuran, molinate, atrazine, simazine and tebuconazole in rice samples. In this innovative procedure, a rice sample is inserted into the cavity of the rotating disk device which is then immersed in an aqueous solution followed by high-speed agitation. In this case, water is employed as a green solvent for leaching the analytes from the sample matrix. Simultaneously, a solid-phase microextraction fiber comprised of divinylbenzene/carboxen/polydimethylsiloxane (2 cm length and 50/30 µm film thickness) was immersed in the aqueous solution to extract the slightly polar analytes from the aqueous matrix with subsequent thermal desorption in the injector of a gas chromatograph-mass spectrometer instrument. The optimal extraction conditions were obtained using an extraction temperature of 80 °C for 40 min, with 125 mg of rice inserted in the rotating disk. Using the previously optimized extraction conditions, the analytical performance was satisfactory with correlation coefficients higher than 0.9881 for all analytes, limits of detection ranging from 0.46 to 5.9 ng g-1, limits of quantification from 1.5 to 19.7 ng g-1, relative recoveries from 76 to 109%, intra-day precision (n = 3) from 1.3 to 19%, and inter-day precision (n = 9) from 3.5 to 6.5%. The proposed method represents a promising alternative for the analysis of complex solid food samples using SPME, since the SPME fiber damage is substantially decreased when the contact with the solid matrix is avoided.

Exploiting green sorbents in rotating-disk sorptive extraction for the determination of parabens by high-performance liquid chromatography with tandem electrospray ionization triple quadrupole mass spectrometry.

In this study, the viability of applying cork and montmorillonite clay modified with ionic liquid as biosorbents in the rotating-disk sorptive extraction technique was investigated. Specifically, this was aimed at the determination of methyl paraben, ethyl paraben, propyl paraben, and isobutyl paraben, with separation/determination by high-performance liquid chromatography coupled with mass spectrometry. The optimization of the method for both biosorbents was performed using multivariate procedures. The extraction efficiencies for the target compounds in aqueous matrices were compared to those obtained using the commercial sorbent Octadecil Silano-C18. The optimum extraction conditions for both natural sorbents were the use of an ammonia solution (pH 10) as desorption solvent and an extraction time of 30 min. The proposed methods show limits of quantification of 0.8 µg/L for cork, 3.0 µg/L for montmorillonite clay and 6.0 µg/L for Octadecil Silano-C18. The relative recoveries from river water and tap water samples ranged from 80.3 to 118.7% and 80.0 to 119.9% for cork and montmorillonite clay modified with ionic liquid, respectively. Relative standard deviations were obtained for intra- and interday precisions of <15% and <19% for cork and <19% and <17% for montmorillonite clay modified with ionic liquid.

Ionic liquids intercalated in montmorillonite as the sorptive phase for the extraction of low-polarity organic compounds from water by rotating-disk sorptive extraction.

Montmorillonite (MMT) clays were modified by the intercalation into their galleries of ionic liquids (IL) based on imidazolium quaternary ammonium salts. This new eco-materials exhibited good features for use as a sorptive phase in the extraction of low-polarity analytes from aqueous samples. Spectroscopic analyses of the modified clays were conducted and revealed an increase in the basal spacing and a shifting of the reflection plane towards lower values as a consequence of the effective intercalation of organic cations into the MMT structure. The novel sorbent developed herein was assayed as the sorptive phase in rotating-disk sorptive extraction (RDSE), using polychlorinated biphenyls (PCBs), representative of low-polarity pollutants, as model analytes. The final determination was made by gas chromatography with electron capture detection. Among the synthetized sorptive phases, the selected system for analytical purposes consisted of MMT modified with the 1-hexadecyl-3-methylimidazolium bromide (HDMIM-Br) IL. Satisfactory analytical features were achieved using a sample volume of 5 mL: the relative recoveries from a wastewater sample were higher than 80%, the detection limits were between 3 ng L-1 and 43 ng L-1, the precision (within-run precision) expressed as the relative standard deviation ranged from 2% to 24%, and the enrichment factors ranged between 18 and 28. Using RDSE, the extraction efficiency achieved for the selected MMT-HDMIM-Br phase was compared with other commercial solid phases/supports, such as polypropylene, polypropylene with 1-octanol (as a supported liquid membrane), octadecyl (C18) and octyl (C8), and showed the highest response for all the studied analytes. Under the optimized extraction conditions, this new device was applied in the analysis of the influent of a wastewater treatment plant in Santiago (Chile), demonstrating its applicability through the good recoveries and precision achieved with real samples.

Hollow-fiber solvent bar microextraction with gas chromatography and electron capture detection determination of disinfection byproducts in water samples.

A liquid-phase microextraction method that uses a hollow-fiber solvent bar microextraction technique was developed by combining gas chromatography with electron capture detection for the analysis of four trihalomethanes (chloroform, dichlorobromomethane, chlorodibromomethane, and bromoform) in drinking water. In the microextraction process, 1-octanol was used as the solvent. The technique operates in a two-phase mode with a 5 min extraction time, a 700 rpm stirring speed, a 30°C extraction temperature, and NaCl concentration of 20%. After microextraction, one edge of the membrane was cut, and 1 µL of solvent was collected from the membrane using a 10 µL syringe. The solvent sample was directly injected into the gas chromatograph. The analytical characteristics of the developed method were as follows: detection limits, 0.017-0.037 ng mL-1 ; linear working range, 10-900 ng mL-1 ; recovery, 74 ± 9-91 ± 2; relative standard deviation, 5.7-10.3; and enrichment factor, 330-455. A simple, fast, economic, selective, and efficient method with big possibilities for automation was developed with a potential use to apply with other matrices and analytes.

Análisis de cocaína en diferentes muestras por cromatografía de gases con detector de ionización de llama (CG-FID) / Analysis of cocaine in different samples by gas chromatography flame ionization detector (GC-FID) / Análise de cocaína em diferentes amostras por cromatografia gasosa com detector de ionização de chama (GC-FID)

En este estudio se realizó la validación de los métodos establecidos por la UNODC para la cuantificación y extracción de benzometilecgonina (cocaína) presente en las hojas de Erythhroxylum coca, en té de coca y en clorhidrato de cocaína. El primer método de extracción, recomendado por la UNODC, es una extracción solido-líquido (ESL), sin embargo, los resultados obtenidos indican que esta no es lo suficientemente eficiente para lograr una señal de analito distinguible de la relación señal a ruido (S/N) para las muestras de hojas de Erythhroxylum coca y té de coca. El segundo método propuesto es la extracción soxhlet, los resultados indican que esta resulta más eficiente para aislar y cuantificar el analito de interés por cromatografía de gases acoplada a un detector de ionización por llama (CG-FID). Después de someter las muestras al proceso de extracción soxhlet y cuantificación por CG-FID se encontró que la hoja de té posee 7,66×10² mg de cocaína/kg de muestra, las hojas de coca 17,15 mg de cocaína/kg de muestra y el clorhidrato de cocaína 7,15×10(5) mg de cocaína/kg de muestra. El método de análisis escogido se caracteriza por arrojar bajos límites de detección (0,169 mg/L) y por poseer parámetros estadísticos y cromatográficos ideales.

In this study validate the methods established by the UNODC for quantification and extraction benzometilecgonina (cocaine) in the leaves of Erythhroxylum coca, coca tea and cocaine hydrochloride. The first extraction method recommended by the UNODC is a solid-liquid extraction (ESL), however, the results indicate that this is not efficient enough to achieve analyte signal distinguishable from the signal to noise ratio (S/N) for samples Erythhroxylum coca leaves and coca tea. The second proposed method is soxhlet extraction, the results indicate that this is more efficient to isolate and quantify the analyte of interest by gas chromatography coupled to a flame ionization detector (GC-FID). After submitting the samples to the soxhlet extraction process and quantification by GC-FID it found that tea leaf has 7.66×10² mg of cocaine/kg sample, coca leaves 17.15 mg of cocaine/kg sample and cocaine hydrochloride concentration corresponded to 7.15×10(5) mg of cocaine/kg sample. The chosen analysis method is characterized by low detection limits shed (1.69 mg/L) and possessing ideal chromatographic and statistical parameters.

Neste estudo validaram-se os métodos estabelecidos pelo UNODC para a quantificação e extração de benzometilecgonina (cocaína) nas folhas de Erythhroxylum coca; em chá de coca e cloridrato de cocaína. O primeiro método de extração recomendado por UNODC é uma extração sólido-líquido (ESL), no entanto, os resultados indicam que esta não é suficientemente eficaz para atingir um sinal de analito distinguível da relação sinal-ruído (S/N) para amostras de folhas Erythhroxylum coca e chá de coca. O segundo método proposto é uma extração soxhlet, os resultados indicam que este é mais eficiente para isolar e quantificar o analito de interesse por cromatografia gasosa acoplada a um detector de ionização de chama (GC-FID). Depois de enviar as amostras para o processo de extração soxhlet e quantificação por GC-FID descobriu-se que as folhas de chá têm 7,66×10² mg de cocaína/kg de amostra, as folhas de coca 17,15 mg de cocaína/kg de amostra e o cloridrato de cocaína 7,15×10(5) mg de cocaína/kg de amostra. O método de análise escolhido é caracterizado por ter baixos limites de detecção (1,69 mg/L) e possuir parâmetros estatísticos e cromatográficos ideais.

Three-phase hollow-fiber liquid-phase microextraction combined with HPLC-UV for the determination of isothiazolinone biocides in adhesives used for food packaging materials.

The present study deals with the development of a liquid microextraction procedure for enhancing the sensitivity of the determination of 2-methyl-4-isothiazolin-3-one and 5-chloro-2-methyl-4-isothiazolin-3-one in adhesives. The procedure involves a three-phase hollow-fiber liquid-phase microextraction using a semipermeable polypropylene membrane, which contained 1-octanol as the organic phase in the pores of the membrane. The donor and acceptor phases are aqueous acidic and alkaline media, respectively, and the final liquid phase (acceptor) is analyzed by HPLC coupled with diode array detection. The most appropriate conditions were extraction time 20 min, stirring speed 1400 rpm, extraction temperature 50°C. The quantification limits of the method were 0.123 and 0.490 µg/g for 2-methyl-4-isothiazolin-3-one and 5-chloro-2-methyl-4-isothiazolin-3-one, respectively. Three different adhesive samples were successfully analyzed. The procedure was compared to direct analysis using ultra high pressure liquid chromatography coupled with TOF-MS, where the identification of the compounds and the quantification values were confirmed.

Montaje y validación del método de análisis poscombustión y detección por infrarrojo no dispersivo para determinación de carbono orgánico total (cot) en agua / Assembly and validation by the method of combustion analysis and ondispersive innfrared detection for determining total organic carbon (toc) in water

La técnica de análisis por combustión y detección por infrarrojo no dispersivo (IRND) fue validada para la determinación de materia orgánica en agua, cuantificada como carbono orgánico total (COT). Previamente se optimizó la eliminación del carbono inorgánico (CI) de la muestra con un tiempo óptimo de 1,5 min y una relación ácido de 5%. Se estableció un rango dinámico lineal (RDL) entre 3 y 20 mg/L de COT, en el cual la recta de regresión cumplió con los parámetros que acreditaron su linealidad según el análisis por el método de los mínimos cuadrados, mostrando un coeficiente de correlación de 0,9994. La sensibilidad expresada por la pendiente de la recta de regresión indicó una variación de aproximadamente 5 unidades en la respuesta del detector por cada mg/L de COT. Los límites de detección y cuantificación obtenidos a partir de la recta de regresión fueron 0,517 y 1,722 mg/L de COT, respectivamente. La precisión de la técnica, teniendo como meta un 5% en coeficiente de variación (CV), fue mejor en el agua potable y en concentraciones cercanas a ésta (aprox. 7 mg/L de COT), mientras que las mayores desviaciones se presentaron en concentraciones cercanas a los límites inferior y superior del RDL. Las recuperaciones de concentraciones conocidas sobre muestras reales adicionadas fueron del 85% con baja adición y del 83% con adición alta, valores que sugieren una reevaluación del desempeño de la técnica con respecto a su exactitud, no obstante se alcanzó la meta de recuperación comprendida entre el 70 y el 130%. La técnica así establecida es por tanto apta para el análisis de aguas crudas, potables y residuales y es viable su utilización en el seguimiento a procesos de oxidación avanzada aplicados en el tratamiento de agua para consumo humano.

The technique of combustion analysis and detection by non-dispersive infrared (NDIR) was validated for the determination of organic matter in water, quantified as total organic carbon (TOC). Previously optimized the elimination of inorganic carbon (IC) of the sample with an optimum time sparge of 1.5 min and an acid ratio of 5%. It established a linear dynamic range (LDR) between 3 and 20 mg/L of TOC, in which the regression line that met the parameters credited its linearity as analyzed by the method of least squares, showing a correlation coefficient of 0,9994. The sensitivity expressed by the slope of the regression line indicated a variation of about 5 units in the detector response for each mg/L of TOC. The detection and quantification limits obtained from the regression line were 0.517 and 1.722 mg/L of TOC, respectively. The precision of the technique, aiming at 5% coefficient of variation (CV) was better in the drinking water at concentrations close to it (about 7 mg/L of TOC), whereas larger deviations were presented at concentrations near the lower and upper limits of LDR. The recoveries of known concentrations of actual samples of 85% additions were low addition and 83% with high added values that suggest a reevaluation of the performance of the technique with respect to its accuracy, however the goal was reached between recovery 70 to 130%. The technique is well established thereby capable of analyzing raw water, drinking and waste and feasible to use in monitoring advanced oxidation processes applied in the treatment of drinking water.