Cooperative Effects Drive Water Oxidation Catalysis in Cobalt Electrocatalysts through the Destabilization of Intermediates.

A barrier to understanding the factors driving catalysis in the oxygen evolution reaction (OER) is understanding multiple overlapping redox transitions in the OER catalysts. The complexity of these transitions obscure the relationship between the coverage of adsorbates and OER kinetics, leading to an experimental challenge in measuring activity descriptors, such as binding energies, as well as adsorbate interactions, which may destabilize intermediates and modulate their binding energies. Herein, we utilize a newly designed optical spectroelectrochemistry system to measure these phenomena in order to contrast the behavior of two electrocatalysts, cobalt oxyhydroxide (CoOOH) and cobalt-iron hexacyanoferrate (cobalt-iron Prussian blue, CoFe-PB). Three distinct optical spectra are observed in each catalyst, corresponding to three separate redox transitions, the last of which we show to be active for the OER using time-resolved spectroscopy and electrochemical mass spectroscopy. By combining predictions from density functional theory with parameters obtained from electroadsorption isotherms, we demonstrate that a destabilization of catalytic intermediates occurs with increasing coverage. In CoOOH, a strong (∼0.34 eV/monolayer) destabilization of a strongly bound catalytic intermediate is observed, leading to a potential offset between the accumulation of the intermediate and measurable O2 evolution. We contrast these data to CoFe-PB, where catalytic intermediate generation and O2 evolution onset coincide due to weaker binding and destabilization (∼0.19 eV/monolayer). By considering a correlation between activation energy and binding strength, we suggest that such adsorbate driven destabilization may account for a significant fraction of the observed OER catalytic activity in both materials. Finally, we disentangle the effects of adsorbate interactions on state coverages and kinetics to show how adsorbate interactions determine the observed Tafel slopes. Crucially, the case of CoFe-PB shows that, even where interactions are weaker, adsorption remains non-Nernstian, which strongly influences the observed Tafel slope.

Facile and Eco-Friendly Approach To Produce Confined Metal Cluster Catalysts.

Zeolite-supported metal nanocluster catalysts have attracted significant attention due to their broad application in heterogeneously catalyzed reactions. The preparation of highly dispersed metal catalysts commonly involves the use of organic compounds and requires the implementation of complicated procedures, which are neither green nor deployable at the large scale. Herein, we present a novel facile method (vacuum-heating) which employs a specific thermal vacuum processing protocol of catalysts to promote the decomposition of metal precursors. The removal of coordinated H2O via vacuum-heating restricts the formation of intermediates (metal-bound OH species), resulting in catalysts with a uniform, metal nanocluster distribution. The structure of the intermediate was determined by in situ Fourier transform infrared, temperature-programmed decomposition, and X-ray absorption spectroscopy (XAS) measurements. This alternative synthesis method is eco-friendly and cost-effective as the procedure occurs in the absence of organic compounds. It can be widely used for the preparation of catalysts from different metal species (Ni, Fe, Cu, Co, Zn) and precursors and is readily scaled-up.

Surface charge as activity descriptors for electrochemical CO2 reduction to multi-carbon products on organic-functionalised Cu.

Intensive research in electrochemical CO2 reduction reaction has resulted in the discovery of numerous high-performance catalysts selective to multi-carbon products, with most of these catalysts still being purely transition metal based. Herein, we present high and stable multi-carbon products selectivity of up to 76.6% across a wide potential range of 1 V on histidine-functionalised Cu. In-situ Raman and density functional theory calculations revealed alternative reaction pathways that involve direct interactions between adsorbed histidine and CO2 reduction intermediates at more cathodic potentials. Strikingly, we found that the yield of multi-carbon products is closely correlated to the surface charge on the catalyst surface, quantified by a pulsed voltammetry-based technique which proved reliable even at very cathodic potentials. We ascribe the surface charge to the population density of adsorbed species on the catalyst surface, which may be exploited as a powerful tool to explain CO2 reduction activity and as a proxy for future catalyst discovery, including organic-inorganic hybrids.

Facile Solution Process of VO2 Film with Mesh Morphology for Enhanced Thermochromic Performance.

The fabrication and applications of VO2 film continue to be of considerable interest due to their good thermochromic performance for smart windows. However, low visible transmittance (Tlum) and solar modulation efficiency (∆Tsol) impede the application of VO2 film, and they are difficult to improve simultaneously. Here, a facile zinc solution process was employed to control the surface structure of dense VO2 film and the processed VO2 film showed enhanced visible transmittance and solar modulation efficiency, which were increased by 7.5% and 9.5%, respectively, compared with unprocessed VO2 film. This process facilitated the growth of layered basic zinc acetate (LBZA) nanosheets to form mesh morphology on the surface of VO2 film, where LBZA nanosheets enhance the visible transmittance as an anti-reflection film. The mesh morphology also strengthened the solar modulation efficiency with small caves between nanosheets by multiplying the times of reflection. By increasing the zinc concentration from 0.05 mol/L to 0.20 mol/L, there were more LBZA nanosheets on the surface of the VO2 film, leading to an increase in the solar/near-infrared modulation efficiency. Therefore, this work revealed the relationship between the solution process, surface structure, and optical properties, and thus can provide a new method to prepare VO2 composite film with desirable performance for applications in smart windows.

On the effect of metal loading on the reducibility and redox chemistry of ceria supported Pd catalysts.

The effect of Pd loading on the redox characteristics of a ceria support was examined using in situ Pd K-edge XAS, Ce L3-edge XAS and in situ X-ray diffraction techniques. Analysis of the data obtained from these techniques indicates that the onset temperature for the partial reduction of Ce(IV) to Ce(III), by exposure to H2, varies inversely with the loading of Pd. Whilst the onset and completion temperatures of the reduction of Ce(IV) to Ce(III) are different, both samples yield the same maximal fraction of Ce(III) formation independent of Pd loading. Furthermore, the partial reduction of Ce is found to be concurrent with the reduction of PdO and demonstrated that the presence of metallic Pd is necessary for the reduction of the CeO2 support. Upon passivation by room temperature oxidation, a full oxidation of the reduced ceria support was observed. However, only a mild surface oxidation of Pd was identified. The mild passivation of the Pd is found to lead to a highly reactive sample upon a second reduction by H2. The onset of the reduction of Pd and Ce has been demonstrated to be independent of the Pd loading after a mild passivation with both samples exhibiting near room temperature reduction in the presence of H2.

Monitoring the process of formation of ZnO from ZnO2usingin situcombined XRD/XAS technique.

Use ofin situcombined x-ray diffraction and x-ray absorption spectroscopy for the study of the thermal decomposition of zinc peroxide to zinc oxide is reported here. Comparison of data extracted from both x-ray diffraction (XRD) and x-ray absorption spectroscopy (XAS) with thermo gravimetric analysis (TGA) enabled us to follow the nature of the conversion of ZnO2to ZnO. A temperature range between 230 °C and 350 °C appears to show that a very poorly crystalline ZnO is formed prior to the formation of an ordered ZnO material. Both the decrease in white line intensity in the Zn K-edge XANES and resulting lower coordination numbers estimated from analysis of the Zn K-edge data of ZnO heated at 500 °C, in comparison to bulk ZnO, suggest that the ZnO produced by this method has significant defects in the system.

Elucidation of copper environment in a Cu-Cr-Fe oxide catalyst through in situ high-resolution XANES investigation.

Copper containing materials are widely used in a range of catalytic applications. Here, we report the use of Cu K-edge high resolution XANES to determine the local site symmetry of copper ions during the thermal treatment of a Cu-Cr-Fe oxide catalyst. We exploited the Cu K-edge XANES spectral features, in particular the correlation between area under the pre-edge peak and its position to determine the local environment of Cu2+ ions. The information gained from this investigation rules out the presence of Cu2+ ions in a tetrahedral or square planar geometry, a mixture of these sites, or in a reduced oxidation state. Evidence is presented that the Cu2+ ions in the Cu-Cr-Fe oxide system are present in a distorted octahedral environment.

Following the Formation of Silver Nanoparticles Using In Situ X-ray Absorption Spectroscopy.

The formation of silver and Au@Ag core@shell nanoparticles via reduction of AgNO3 by trisodium citrate was followed using in situ X-ray absorption near-edge structure (XANES) spectroscopy and time-resolved UV-visible (UV-vis) spectroscopy. The XANES data were analyzed through linear combination fitting, and the reaction kinetics were found to be consistent with first-order behavior with respect to silver cations. For the Au@Ag nanoparticles, the UV-vis data of a lab-scale reaction showed a gradual shift in dominance between the gold- and silver-localized surface plasmon absorbance bands. Notably, throughout much of the reaction, distinct gold and silver contributions to the UV-vis spectra were observed; however, in the final product, the contributions were not distinct.

Temperature reversible synergistic formation of cerium oxyhydride and Au hydride: a combined XAS and XPDF study.

In situ studies on the physical and chemical properties of Au in inverse ceria alumina supported catalysts have been conducted between 295 and 623 K using high energy resolved fluorescence detection X-ray absorption near edge spectroscopy and X-ray total scattering. Precise structural information is extracted on the metallic Au phase present in a 0.85 wt% Au containing inverse ceria alumina catalyst (ceria/Au/alumina). Herein evidence for the formation of an Au hydride species at elevated temperature is presented. Through modelling of total scattering data to extract the thermal properties of Au using Grüneisen theory of volumetric thermal expansion it proposed that the Au Hydride formation occurs synergistally with the formation of a cerium oxyhydride. The temperature reversible nature, whilst remaining in a reducing atmosphere, demonstrates the activation of hydrogen without consumption of oxygen from the supporting ceria lattice.

Understanding the role of zinc dithiocarbamate complexes as single source precursors to ZnS nanomaterials.

Zinc sulfide is an important wide-band gap semi-conductor and dithiocarbamate complexes [Zn(S2CNR2)2] find widespread use as single-source precursors for the controlled synthesis of ZnS nanoparticulate modifications. Decomposition of [Zn(S2CNiBu2)2] in oleylamine gives high aspect ratio wurtzite nanowires, the average length of which was increased upon addition of thiuram disulfide to the decomposition mixture. To provide further insight into the decomposition process, X-ray absorption spectroscopy (XAS) of [Zn(S2CNMe2)2] was performed in the solid-state, in non-coordinating xylene and in oleylamine. In the solid-state, dimeric [Zn(S2CNMe2)2]2 was characterised in accord with the single crystal X-ray structure, while in xylene this breaks down into tetrahedral monomers. In situ XAS in oleylamine (RNH2) shows that the coordination sphere is further modified, amine binding to give five-coordinate [Zn(S2CNMe2)2(RNH2)]. This species is stable to ca. 70 °C, above which amine dissociates and at ca. 90 °C decomposition occurs to generate ZnS. The relatively low temperature onset of nanoparticle formation is associated with amine-exchange leading to the in situ formation of [Zn(S2CNMe2)(S2CNHR)] which has a low temperature decomposition pathway. Combining these observations with the previous work of others allows us to propose a detailed mechanistic scheme for the overall process.

Electronic and Geometric Structures of Rechargeable Lithium Manganese Sulfate Li2Mn(SO4)2 Cathode.

Here, we report the use of Li2Mn(SO4)2 as a potential energy storage material and describe its route of synthesis and structural characterization over one electrochemical cycle. Li2Mn(SO4)2 is synthesized by ball milling of MnSO4·H2O and Li2SO4·H2O and characterized using a suite of techniques, in particular, ex situ X-ray diffraction, X-ray photoelectron spectroscopy, and X-ray absorption spectroscopy on the Mn and S K-edges to investigate the electronic and local geometry around the absorbing atoms. The prepared Li2Mn(SO4)2 electrodes undergo electrochemical cycles to different potential points on the charge-discharge curve and are then extracted from the cells at these points for ex situ structural analysis. Analysis of X-ray absorption spectroscopy (both near and fine structure part of the data) data suggests that there are minimal changes to the oxidation state of Mn and S ions during charge-discharge cycles. However, X-ray photoelectron spectroscopy analysis suggests that there are changes in the oxidation state of Mn, which appears to be different from the conclusion drawn from X-ray absorption spectroscopy. This difference in results during cycling can thus be attributed to electrochemical reactions being dominant at the surface of the Li2Mn(SO4)2 particles rather than in the bulk.

High-Pressure Study of the Elpasolite Perovskite La2NiMnO6.

Here we report a high-pressure investigation into the structural and magnetic properties of the double perovskite La2NiMnO6 using neutron scattering over a temperature range of 4.2-300 K at ambient pressure and over a temperature range of 120-1177 K up to a maximum pressure of 6.6 GPa. X-ray diffraction was also used up to a maximum pressure of 64 GPa, over a temperature range of 300-720 K. The sample was found to exist in a mixed rhombohedral/monoclinic symmetry at ambient conditions, the balance of which was found to be strongly temperature- and pressure-dependent. Alternating current magnetometry and X-ray absorption near-edge structure measurements were made at ambient pressure to characterize the sample, suggesting that the transition-metal sites exist in a mixed Ni3+/Mn3+ and Ni2+/Mn4+ state at ambient temperature and pressure. Analysis of the magnetic properties of the sample shows that the Curie temperature can be enhanced by ∼12 K with 2 GPa applied pressure, but it is highly stable at pressures beyond this. We report a pressure-volume-temperature equation of state for this material over this combined temperature and pressure range, with an ambient temperature bulk modulus of ∼179(8) GPa. The previously reported transition from monoclinic to rhombohedral symmetry upon heating to 700 K is seen to be encouraged with applied pressure, transforming fully by ∼1.5 GPa. Raman spectroscopy data were collected up to ∼8 GPa and show no clear changes or discontinuities over the reported phase transition to rhombohedral symmetry or any indication of further changes over the range considered. The ambient-pressure Grüneisen parameter γth was determined to be γth = 2.6 with a Debye temperature of 677 K. The individual modal parameters γj at ambient temperature were also determined from the high-pressure Raman data.

Fe(ii) and Fe(iii) dithiocarbamate complexes as single source precursors to nanoscale iron sulfides: a combined synthetic and in situ XAS approach.

Nanoparticulate iron sulfides have many potential applications and are also proposed to be prebiotic catalysts for the reduction of CO2 to biologically important molecules, thus the development of reliable routes to specific phases with controlled sizes and morphologies is important. Here we focus on the use of iron dithiocarbamate complexes as single source precursors (SSPs) to generate greigite and pyrrhotite nanoparticles. Since these minerals contain both iron(iii) and iron(ii) centres, SSPs in both oxidation states, [Fe(S2CNR2)3] and cis-[Fe(CO)2(S2CNR2)2] respectively, have been utilised. Use of this Fe(ii) precursor is novel and it readily loses both carbonyls in a single step (as shown by TGA measurements) providing an in situ source of the extremely air-sensitive Fe(ii) dithiocarbamate complexes [Fe(S2CNR2)2]. Decomposition of [Fe(S2CNR2)3] alone in oleylamine affords primarily pyrrhotite, although by careful control of reaction conditions (ca. 230 °C, 40-50 nM SSP) a window exists in which pure greigite nanoparticles can be isolated. With cis-[Fe(CO)2(S2CNR2)2] we were unable to produce pure greigite, with pyrrhotite formation dominating, a similar situation being found with mixtures of Fe(ii) and Fe(iii) precursors. In situ X-ray absorption spectroscopy (XAS) studies showed that heating [Fe(S2CNiBu2)3] in oleylamine resulted in amine coordination and, at ca. 60 °C, reduction of Fe(iii) to Fe(ii) with (proposed) elimination of thiuram disulfide (S2CNR2)2. We thus carried out a series of decomposition studies with added thiuram disulfide (R = iBu) and found that addition of 1-2 equivalents led to the formation of pure greigite nanoparticles between 230 and 280 °C with low SSP concentrations. Average particle size does not vary significantly with increasing concentration, thus providing a convenient route to ca. 40 nm greigite nanoparticles. In situ XAS studies have been carried out and allow a decomposition pathway for [Fe(S2CNiBu2)3] in oleylamine to be established; reduction of Fe(iii) to Fe(ii) reduction triggers substitution of the secondary amide backbone by oleylamine (RNH2) resulting in the in situ formation of a primary dithiocarbamate derivative [Fe(RNH2)2(S2CNHR)2]. This in turn extrudes RNCS to afford molecular precursors of the observed FeS nanomaterials. The precise role of thiuram disulfide in the decomposition process is unknown, but it likely plays a part in controlling the Fe(iii)-Fe(ii) equilibrium and may also act as a source of sulfur allowing control over the Fe : S ratio in the mineral products.

Insight into the Nature of Iron Sulfide Surfaces During the Electrochemical Hydrogen Evolution and CO2 Reduction Reactions.

Greigite and other iron sulfides are potential, cheap, earth-abundant electrocatalysts for the hydrogen evolution reaction (HER), yet little is known about the underlying surface chemistry. Structural and chemical changes to a greigite (Fe3S4)-modified electrode were determined at -0.6 V versus standard hydrogen electrode (SHE) at pH 7, under conditions of the HER. In situ X-ray absorption spectroscopy was employed at the Fe K-edge to show that iron-sulfur linkages were replaced by iron-oxygen units under these conditions. The resulting material was determined as 60% greigite and 40% iron hydroxide (goethite) with a proposed core-shell structure. A large increase in pH at the electrode surface (to pH 12) is caused by the generation of OH- as a product of the HER. Under these conditions, iron sulfide materials are thermodynamically unstable with respect to the hydroxide. In situ infrared spectroscopy of the solution near the electrode interface confirmed changes in the phosphate ion speciation consistent with a change in pH from 7 to 12 when -0.6 V versus SHE is applied. Saturation of the solution with CO2 resulted in the inhibition of the hydroxide formation, potentially due to surface adsorption of HCO3-. This study shows that the true nature of the greigite electrode under conditions of the HER is a core-shell greigite-hydroxide material and emphasizes the importance of in situ investigation of the catalyst under operation to develop true and accurate mechanistic models.

Optimized Atmospheric-Pressure Chemical Vapor Deposition Thermochromic VO2 Thin Films for Intelligent Window Applications.

Monoclinic vanadium(IV) oxide (VO2) has been widely studied for energy-efficient glazing applications because of its thermochromic properties, displaying a large change in transmission of near-IR wavelengths between the hot and cold states. The optimization of the reaction between VCl4 and ethyl acetate via atmospheric-pressure chemical vapor deposition (APCVD) was shown to produce thin films of monoclinic VO2 with excellent thermochromic properties (ΔT sol = 12%). The tailoring of the thermochromic and visible light transmission was shown to be possible by altering the density and morphology of the deposited films. The films were characterized by X-ray diffraction, atomic-force microscopy, scanning electron microscopy, ellipsometry, and UV-vis spectrometry. This article provides useful design rules for the synthesis of high-quality VO2 thin films by APCVD.

Controlling the Cross-Sensitivity of Carbon Nanotube-Based Gas Sensors to Water Using Zeolites.

Carbon nanotube-based gas sensors can be used to detect harmful environmental pollutants such as NO2 at room temperature. Although they show promise as low-powered, sensitive, and affordable monitoring devices, cross-sensitivity of functionalized carbon nanotubes to water vapor often obscures the detection of target molecules. This is a barrier to adoption for monitoring of airborne pollutants because of the varying humidity levels found in real world environments. Zeolites, also known as molecular sieves because of their selective adsorption properties, are used in this work to control the cross-sensitivity of single-walled carbon nanotube (SWCNT)-based sensors to water vapor. Zeolites incorporated into the sensing layer are found to reduce interference effects that would otherwise obscure the identification of NO2 gas, permitting repeatable detection over a range of relative humidities. This significant improvement is found to depend on the arrangement of the SWCNT-zeolite layers in the sensing device, as well as the hydrophilicity of the chosen zeolite.

Structure of Nano-sized CeO2 Materials: Combined Scattering and Spectroscopic Investigations.

The structure of several nano-sized ceria, CeO2 , systems was investigated using neutron and X-ray diffraction and X-ray absorption spectroscopy. Whilst both diffraction and total pair distribution functions (PDFs) revealed that in all of the samples the occupancy of both Ce4+ and O2- are very close to the ideal stoichiometry, the analysis using Reverse Monte Carlo technique revealed significant disorder around oxygen atoms in the nano-sized ceria samples in comparison to the highly crystalline NIST standard. In addition, the analysis revealed that the main differences observed in the pair correlations from various X-ray and neutron diffraction techniques were attributable to the particle size of the CeO2 prepared by the reported three methods. Furthermore, detailed analysis of the Ce L3 - and K-edge EXAFS data support this finding; in particular the decrease in higher shell coordination numbers with respect to the NIST standard, is attributed to differences in particle size.

Rutile to anatase phase transition induced by N doping in highly oriented TiO2 films.

Highly oriented TiO2 thin films were deposited onto Al2O3(0001), SrTiO3(001), and LaAlO3(001) substrates by spin coating a titanium alkoxide precursor solution followed by annealing. The films were nitrogen doped by two different routes: either by adding tetramethyethylenediamine (TMEDA) to the precursor solution or alternatively by high temperature ammonolysis. Undoped TiO2 films were highly oriented and the phase was dependent on the substrate. N doping by ammonolysis led to transformation of rutile films to anatase, confirmed by XRD and by XPS valence band spectroscopy. Significant differences were observed in the spatial distribution of the nitrogen dopant depending upon which synthesis method was used. These two factors may shed light on the increased photocatalytic efficiencies reported in N doped TiO2.

Phase control during the synthesis of nickel sulfide nanoparticles from dithiocarbamate precursors.

Square-planar nickel bis(dithiocarbamate) complexes, [Ni(S2CNR2)2], have been prepared and utilised as single source precursors to nanoparticulate nickel sulfides. While they are stable in the solid-state to around 300 °C, heating in oleylamine at 230 °C, 5 mM solutions afford pure α-NiS, where the outcome is independent of the substituents. DFT calculations show an electronic effect rather than steric hindrance influences the resulting particle size. Decomposition of the iso-butyl derivative, [Ni(S2CN(i)Bu2)2], has been studied in detail. There is a temperature-dependence of the phase of the nickel sulfide formed. At low temperatures (150 °C), pure α-NiS is formed. Upon raising the temperature, increasing amounts of ß-NiS are produced and at 280 °C this is formed in pure form. A range of concentrations (from 5-50 mM) was also investigated at 180 °C and while in all cases pure α-NiS was formed, particle sizes varied significantly. Thus at low concentrations average particle sizes were ca. 100 nm, but at higher concentrations they increased to ca. 150 nm. The addition of two equivalents of tetra-iso-butyl thiuram disulfide, ((i)Bu2NCS2)2, to the decomposition mixture was found to influence the material formed. At 230 °C and above, α-NiS was generated, in contrast to the results found without added thiuram disulfide, suggesting that addition of ((i)Bu2NCS2)2 stabilises the metastable α-NiS phase. At low temperatures (150-180 °C) and concentrations (5 mM), mixtures of α-NiS and Ni3S4, result. A growing proportion of Ni3S4 is noted upon increasing precursor concentration to 10 mM. At 20 mM a metastable phase of nickel sulfide, NiS2 is formed and as the concentration is increased, α-NiS appears alongside NiS2. Reasons for these variations are discussed.