Do strength of zirconia-abutment-interfaces depend on cement, zirconia type and titanium abutment dimensions?

OBJECTIVES: Part 1 of this study investigates the influence of zirconia types, chimney heights, and gingival heights on the strength of the zirconia-abutment-interface. Part 2 extends the analysis to include adhesive brands and macro-retentions. METHODS: In Part 1, the study utilized three zirconia types (700 MPa, 1000 MPa, 1200 MPa) to fabricate 234 screw-retained zirconia crowns with varying chimney heights (3.5 mm, 4.1 mm, 5 mm) and gingival heights (0.65 mm, 1.2 mm, 3 mm) of the titanium abutments. All adherend surfaces underwent sandblasting with aluminum oxide before cementation with a specific resin cement. In Part 2, the investigation of 240 screw-retained zirconia crowns focused on a single zirconia type (1000 MPa) with chimney heights of 3.5 mm and 5 mm and a gingival height of 0.65 mm of the titanium abutments, cemented with three different resin cements. All adherent surfaces underwent sandblasting with aluminum oxide before cementation, whereas 120 out of 240 abutments received additional macro retentions. Storage in water at 37 °C for 24 h preceded the tensile test. RESULTS: The study revealed a substantial impact of chimney height and zirconia type on the bond strength of the zirconia-abutment-interface. Neither adhesive brands nor macro retentions significantly impacted the bond strength. Fracture incidence was significantly influenced by gingival height and zirconia type in part 1, whereas in part 2 smaller chimney heights correlated with a higher fracture incidence. SIGNIFICANCE: This study contributes insights into the complex interplay of factors influencing the zirconia-abutment-interface. The results provide a foundation for refining clinical approaches, emphasizing the importance of chimney height and zirconia type in achieving successful anterior gap implant restorations.

Clinical and Radiographic Outcomes of Single Implant-Supported Zirconia Crowns Following a Digital and Conventional Workflow: Four-Year Follow-Up of a Randomized Controlled Clinical Trial.

PURPOSE: This study aimed to compare the clinical and radiographic outcomes of single posterior screw-retained monolithic implant crowns following a digital and conventional workflow and to report on the survival/complication rate after a mean 4-year follow-up. MATERIALS AND METHODS: Thirty patients with a single posterior tooth missing were rehabilitated with a bone-level implant. After a healing period of ≥3 months, they were subjected to both a digital and conventional workflow to fabricate two screw-retained monolithic implant crowns. The quantitative clinical adjustments to both crowns (intrasubject comparison) and a questionnaire were recorded at try-in. Thereafter, a crown of the digital and conventional workflows was randomly inserted. At the last follow-up, the marginal bone level (MBL), peri-implant health-related parameters (bleeding on probing (BoP), plaque, pocket probing depth (PPD)), and functional implant prosthodontic score (FIPS) were assessed. Furthermore, the implant survival and success rates and technical complications were evaluated. RESULTS: A total of 27 patients were followed for a mean period of 4.23 ± 1.10 years. There was no significant difference between the digital and conventional workflows regarding clinical adjustments and questionnaire outcomes. More than twice as many participants recommended digital (n = 16) compared to conventional impressions (n = 7) to friends. The implant survival and success rate were 100% and 96.3%, respectively. Furthermore, two de-cementations and one fracture of the ti-base abutment occurred. There were no significant differences in BoP, plaque, and PPD metrics between the two groups. The changes in the MBL between implant crown insertion (baseline) and the last follow-up were 0.07 ± 0.19 mm and 0.34 ± 0.62 mm in the digital and conventional groups, respectively (p = 0.195). The mean overall FIPS score was 8.11 ± 1.37 (range: 5-10). CONCLUSIONS: The clinical and radiographic outcomes of single screw-retained monolithic implant crowns were similar between both workflows after a mean of 4 years of service. The patients did not clearly prefer an impression technique for their restoration, although they would recommend the digital impression more often to friends. Thus, decision regarding clinical workflows may be based on the patient's and/or clinician's preference.

3D printed indirect bonding trays: Transfer accuracy of hard versus soft resin material in a prospective, randomized, single-blinded clinical study.

OBJECTIVES: This prospective clinical study aimed to compare transfer accuracy and immediate loss rate of hard versus soft transfer trays utilizing a CAD/CAM workflow. METHODS: We performed virtual bracket placement on intraoral scans of adolescent patients to create individual indirect bonding trays. Orthodontic software (Appliance Designer, 3Shape, Copenhagen, Denmark) was used to design the trays, which were then produced using 3D printing technology. Patients were randomly assigned to the hard or soft resin groups with a 1:1 allocation. Subgroups were determined based on the Little's Irregularity Index and distributed equally. RESULTS: 552 brackets were bonded onto adolescent patients using 46 CAD/CAM indirect bonding trays. The linear mean transfer errors ranged from -0.011 mm (soft) to -0.162 mm (hard) and angularly -0.255° (hard) and -0.243° (soft). No statistically significant differences were found between the subgroups or soft and hard resin groups. However, the transfer accuracy of molar brackets was significantly lower in the transversal and horizontal directions. All mean transfer errors were within the limits of clinical acceptability. The loss rate was 2.4 % in the hard resin group and 2.3 % in the soft resin group. The Intra Observer Correlation was excellent. SIGNIFICANCE: CAD/CAM technology for indirect bracket bonding has been proven reliable in a randomized clinical trial. Both hard and soft resin showed a low rate of immediate loss compared to the current literature. Soft resin was more favorable than hard resin in terms of accuracy and usability. However, the indirect bonding of molar brackets is significantly less accurate than incisor brackets.

Medical 3D printing with polyjet technology: effect of material type and printing orientation on printability, surface structure and cytotoxicity.

Due to its high printing resolution and ability to print multiple materials simultaneously, inkjet technology has found wide application in medicine. However, the biological safety of 3D-printed objects is not always guaranteed due to residues of uncured resins or support materials and must therefore be verified. The aim of this study was to evaluate the quality of standard assessment methods for determining the quality and properties of polyjet-printed scaffolds in terms of their dimensional accuracy, surface topography, and cytotoxic potential.Standardized 3D-printed samples were produced in two printing orientations (horizontal or vertical). Printing accuracy and surface roughness was assessed by size measurements, VR-5200 3D optical profilometer dimensional analysis, and scanning electron microscopy. Cytotoxicity tests were performed with a representative cell line (L929) in a comparative laboratory study. Individual experiments were performed with primary cells from clinically relevant tissues and with a Toxdent cytotoxicity assay.Dimensional measurements of printed discs indicated high print accuracy and reproducibility. Print accuracy was highest when specimens were printed in horizontal direction. In all cytotoxicity tests, the estimated mean cell viability was well above 70% (p < 0.0001) regardless of material and printing direction, confirming the low cytotoxicity of the final 3D-printed objects.

CAD/CAM indirect bonding trays using hard versus soft resin material: a single-blinded in vitro study.

OBJECTIVES: The present in vitro study aimed to evaluate the accuracy of three-dimensional (3D) printed indirect bonding trays consisting of hard or soft resin materials produced using computer-aided design and manufacturing (CAD/CAM). METHODS: Forty-eight dental casts were 3D printed. Four groups based on frontal crowding were defined and divided into hard- and soft-resin groups. After virtual bracket positioning on the digital models, the transfer trays were 3D printed. To evaluate the accuracy of the procedure, measurements were performed using a digital overlay of the virtual (target) bracket position and a post-bonding scan. The horizontal, transverse, and vertical deviations and angular discrepancies were analyzed. The loss rate was evaluated descriptively as a percentage. RESULTS: A total of 553 brackets were bonded using 24 soft and 24 resilient indirect bonding trays. The mean deviations were of 0.05 mm (transversal), 0.05 mm (horizontal), 0.09 mm (vertical), 0.13° (angulation) in the resilient resin group and of 0.01 mm (transversal), 0.08 mm (horizontal), 0.08 mm (vertical), 0.37° (angular) in the soft resin group. The loss rate was 6.9% and 0.7% in the hard and soft resin groups, respectively. Angular deviations were significantly higher in the soft resin group (P = 0.009), whereas the loss rate was considerably higher in the hard resin group (P < 0.001). SIGNIFICANCE: The findings indicate that indirect bonding using CAD/CAM is an accurate procedure in the laboratory setting. Soft resins are considered favorable for loss rate and useability.

Comparison of Virtual Intersection and Occlusal Contacts between Intraoral and Laboratory Scans: An In-Vivo Study.

BACKGROUND: The inaccurate maxillomandibular relationship of virtual casts following alignment by the vestibular scan may result in intersection (intermesh penetration) between opposing dental arch surfaces. Intersection occurs at short interocclusal distances in the occlusal contact area (OCA) and may result in infra-occluded definitive restorations. The purpose of this clinical study was to compare initial (by the proprietary scanner software) and new alignments (by a standalone 3D software) of virtual casts regarding OCA and intersection failure. New alignments aimed to rectify intersections by refinement of occlusal contacts. MATERIAL AND METHODS: The virtual casts of 30 patients following digital and conventional impression-taking were analyzed, which were acquired for single implant restoration in the posterior site. Digital impressions were performed by both IOS 1 (3M True Definition) and IOS 2 (TRIOS 3), either as complete- or partial-arch scans, respectively. Mounted gypsum casts were digitized as complete-arch by a laboratory scanner (LS) in enabled and disabled mode to avoid intersection [LS (+)/LS (-)]. All virtual casts were newly aligned by a 3D software. The difference of the OCA and the area of intersection were calculated for initial and new alignments, using interocclusal distance ranges of 0-100 µm, 0-10 µm or <0 µm (=intersection). The difference of the OCA was compared using a linear mixed model. The distribution of occlusal contact points per modality and alignment was assessed independently by three observers and estimated by inter- and intraclass correlation (ICC) coefficients. RESULTS: Virtual casts following initial alignment demonstrated intersections irrespective of the modality. The mean area of the intersection was most for IOS 2 (79.23 mm2), followed by IOS 1 (48.28 mm2), LS (-) (2.77 mm2), and LS (+) (2.01 mm2) in partial-arch scans. Complete-arch scans demonstrated an area of intersection of 70.63 mm2 for IOS 1 followed by 65.52 mm2 (IOS 2), 6.13 mm2 [LS (-)] and 2.76 mm2 [LS (+)]. Newly aligned scans showed no intersections. The overall distribution of occlusal contact points demonstrated moderate reliability (ICC 0.63). Good reliability could be observed (ICC 0.9) for LS (-) scans. CONCLUSIONS: Intersections in the area of occlusal contact points are a phenomenon restricted to virtual casts, which should be considered in CAD/CAM. Initial alignments of LS are less affected by this virtual phenomenon, and contact points may be more distinct according to their anatomic region compared to IOS. Furthermore, intersections can be rectified in a 3D software by adjustment of the maxillomandibular relationship.

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible.

OBJECTIVE: To assess the biomechanical effects of different prosthetic/implant configurations and load directions on 3-unit fixed prostheses supported by short dental implants in the posterior mandible using validated 3-D finite element (FE) models. METHODS: Models represented an atrophic mandible, missing the 2nd premolar, 1st and 2nd molars, and rehabilitated with either two short implants (implant length-IL = 8 mm and 4 mm) supporting a 3-unit dental bridge or three short implants (IL = 8 mm, 6 mm and 4 mm) supporting zirconia prosthesis in splinted or single crowns design. Load simulations were performed in ABAQUS (Dassault Systèmes, France) under axial and oblique (30°) force of 100 N to assess the global stiffness and forces within the implant prosthesis. Local stresses within implant/prosthesis system and strain energy density (SED) within surrounding bone were determined and compared between configurations. RESULTS: The global stiffness was around 1.5 times higher in splinted configurations vs. single crowns, whereby off-axis loading lead to a decrease of 39%. Splinted prostheses exhibited a better stress distribution than single crowns. Local stresses were larger and distributed over a larger area under oblique loads compared to axial load direction. The forces on each implant in the 2-implant-splinted configurations increased by 25% compared to splinted crowns on 3 implants. Loading of un-splinted configurations resulted in increased local SED magnitude. CONCLUSION: Splinting of adjacent short implants in posterior mandible by the prosthetic restoration has a profound effect on the magnitude and distribution of the local stress peaks in peri-implant regions. Replacing each missing tooth with an implant is recommended, whenever bone supply and costs permit.

Experimental validation of a micro-CT finite element model of a human cadaveric mandible rehabilitated with short-implant-supported partial dentures.

PURPOSE: This study aimed to address the predictive value of a micro-computed tomography (µCT)-based finite element (µFE) model of a human cadaveric edentulous posterior mandible, rehabilitated by short dental implants. Hereby, three different prosthetic/implant configurations of fixed partial dentures ("Sp"-3 splinted crowns on 3 implants, "Br" - Bridge: 3 splinted crowns on 2 implants, and "Si"- 3 single crowns) were analysed by comparing the computational predictions of the global stiffness with experimental data. METHODS: Experimental displacement of the bone/implant/prosthesis system was measured under axial and oblique loads of 100 N using an optical deformation system (GOM Aramis) and the overall movement of the testing machine (Zwick Z030). Together with the measured machine force, an "Aramis" (optical markers) and "Zwick" (test machine) stiffness were calculated. FE models were created based on µCT-scans of the cadaveric mandible sample (n = 1) before and after implantation and using stl-files of the crowns. The same load tests and boundary conditions were simulated on the models and the µFE-results were compared to experimental data using linear regression analysis. RESULTS: The regression line through a plot of pooled stiffness values (N/mm) for the optical displacement recording (true local displacement) and the test machine (machine compliance included) had a slope of 0.57 and a correlation coefficient R2 of 0.82. The average pooled correlation of global stiffness between the experiment and FE-analysis (FEA) showed a R2 of 0.80, but the FEA-stiffness was 7.2 times higher. The factor was highly dependent on the test configuration. Sp-configuration showed the largest stiffness followed by Br-configuration (17% difference in experiment and 21% in FEA). CONCLUSIONS: The current study showed good qualitative agreement between the experimental and predicted global stiffness of different short implant configurations. It could be deduced that 1:1 splinting of the short implants by the crowns is most favorable for the stiffness of the implant/prosthesis system. However, in the clinical context, the absolute in silico readings must be interpreted cautiously, as the FEA showed a considerable overestimation of the values.

Optimizing the fitting-surface preparation of zirconia restorations for bonding to dentin.

OBJECTIVES: The aim of this study was to identify the relative strengths and weaknesses of different interfaces within the multilayer structure of a zirconia crown restoration when applying different surface pretreatments. These include the influence on shear strengths of different air abrasion protocols, glaze-on techniques, zirconia primers and self-adhesive cements for either the complex structure: zirconia / self adhesive resin composite cement (RCC) / bovine dentin substrate (part 1) or the RCC / zirconia substrate (part 2). METHODS: In Part 1, zirconia discs, pretreated by either glaze-on techniques or air abrasion using Rocatec™ Soft, were bonded to bovine dentin substrates with different self-adhesive RCCs. In Part 2, steel-cylinders were bonded to zirconia cuboid substrates, pretreated by either different protocols for air-abrasion or a glaze-on-technique, with different self-adhesive RCCs. Shear bond strengths (SBS) were measured for all interfacial combinations. RESULTS: In part 1, application of air abrasion using Rocatec™ Soft significantly increased the SBS of zirconia to dentin compared to control specimens without pretreatment, while glaze-on techniques did not increase the SBS. Pretreatment of zirconia surfaces with two primers (either Clearfil Ceramic Primer, or Monobond S) showed significantly higher SBS than the controls. Cementations with RelyX Unicem 2 Automix showed significantly higher SBS than with MaxCem Elite. In Part 2, all air abrasion protocols increased the SBS, but there was no significant difference between these protocols. Again the glaze-on technique did not increase SBS. A significant difference between the two RCCs was again observed. When zirconia substrates were air abraded, regardless of which protocol was applied, the highest SBS were obtained by Calibra with P&B active followed by Panavia with or without Clearfil Ceramic Primer Plus. Calibra applied without P&B active exhibited the lowest SBS. SIGNIFICANCE: Pretreatment of zirconia substrates using air abrasion and/or ceramic primers increased the SBS of the zirconia cement interface. For all tested glaze-on treatments, in our experimental setting no effect was observed.

Limited reciprocity in curing efficiency of bulk-fill resin-composites.

OBJECTIVE: The aim of the study was to identify experimental limits of the general reciprocity hypothesis that the same photo-cure outcomes will result from applying essentially constant energy densities, despite reciprocal variations in the irradiance and irradiation time-period, for a representative set of bulk fill (BF) and non-BF resin composites. METHODS: Six BF and two non-BF resin-composites were selected. The unset pastes were inserted into white acetal molds (5mm id) with (n=6) depths (1, 2, 3, 4, 5 and 6mm). Three light curing units (LCUs) of increasing radiant emittance capability: 1200, 2000 and 3200mW/cm2 were used. Composite specimen groups (n=3, per depth, per LCU) were irradiated on the upper surface only. For each specific composite, the irradiation times for each LCU were reduced reciprocally, as the LCU irradiance increased, to deliver a constant energy density (J/cm2) to that composite. However, the required energy density for a given composite differed in accordance with each composite manufacturer recommendations. After storing for 24h at 37°C, light transmission measurements were made through each specimen and re-expressed as Apparent Absorbance (A'). Vickers hardness (HV) measurements (n=10) were made on both top and bottom surfaces, for each specimen, and HVversus "depth" profile plots created. From the top-surface data, a Depth-of-Cure parameter could be derived. Data were statistically evaluated for differences between top and bottom HV values and for other predefined variables of interest. RESULTS: Irradiation with the LCU of 1200mW/cm2 generally gave the highest HV/depth for most materials tested compared to the other curing lights with higher power output, regardless of top and bottom measurements (p<0.001). However, this difference was material-dependent. With one BF composite, 1200 and 2000mW/cm2 irradiance did not show a significant difference between top and bottom HV. Composites with higher translucency showed reduced differences in top/bottom HV than more opaque composites. SIGNIFICANCE: Reciprocity was found to be limited with most materials examined, such that irradiance periods of 10s, gave generally better HV outcomes than by using LCUs of superior radiant emittance while reciprocally reducing irradiance time to maintain constant dose of energy density.

Influence of two different cement space settings and three different cement types on the fit of polymer-infiltrated ceramic network material crowns manufactured using a complete digital workflow.

OBJECTIVES: The study evaluates the influence of two spacer settings and three resin luting materials on the marginal and internal fit of polymer-infiltrated ceramic network (PICN) material crowns manufactured using a complete digital workflow. METHODS: Optical impressions of fifty identical dies were performed using the 3M scanner (software version 5.0.2). Twenty crowns were designed using Ceramill Mind (version 3.4.10.1163), from which ten with spacer setting of 50 µm (G1) and ten with 80 µm (G2). Thirty crowns (spacer setting of 50 µm) were divided into three groups corresponding to the resin materials used as follows: RelyX Unicem (RX), Variolink Esthetic (VLE), and Nexus 3 (NX3). All crowns were milled from Vita Enamic blocks. After micro-CT scanning, absolute marginal discrepancy (AMD), internal gap (IG), total cement space volume (TCV), and marginal porosities (VP) were measured. RESULTS: Significant difference was detected on the VP between the RX and NX3 group (p = 0.033). The mean values of all parameters were the following: AMD (µm): G1 182.6, G2 253.7, RX 210.8, VLE 195.5, NX3 186.6; IG (µm): G1 215.6, G2 173.1, RX 171.1, VLE 198.6, NX3 203; TCV (mm3): G1 22.9, G2 20.49, RX 17.57, VLE 17.49, NX3 20.59; VP (mm3): G1 0.26, G2 0.34, RX 0.32, VLE 0.46, NX3 0.54. CONCLUSIONS: Fit of PICN material crowns was not significantly influenced by increasing the spacer settings and cementation with different resin materials. Additionally, RelyX Unicem showed significantly less porosities as compared with Nexus3. CLINICAL RELEVANCE: Both 50 µm and 80 µm virtual spacer settings can be suggested for the manufacture of PICN crowns when Ceramill Mind (version 3.4.10.1163) is used. Furthermore, a self-adhesive system can be recommended for the cementation.

Comparison of Bleaching Products With Up to 6% and With More Than 6% Hydrogen Peroxide: Whitening Efficacy Using BI and WI D and Side Effects - An in vitro Study.

The aim of this study was to evaluate the effect of bleaching agents containing different concentrations of hydrogen peroxide (HP) on color-change and on enamel-surface in bovine teeth. Furthermore the influence on cell viability and proliferation was investigated. Two hundred and forty teeth were randomly assigned into four groups (home bleaching ≤6%, in-office bleaching ≤6%, in-office bleaching > 6% HP, and control group). Bleaching was performed after artificial staining and the bleached index (BI) as well as the whiteness index (WI D ) was measured at several time points. Chemical analysis for HP concentrations and the pH of the bleaching products was done. Furthermore, enamel surfaces of randomly selected specimens were analyzed using scanning electron microscopy (SEM) and cytotoxicity of the tested bleaching products was evaluated in vitro using dental pulp cells (DPCs) and L929 cells. A statistically significant whitening effect was observed in almost all products. As expected all investigated products resulted in decreased cell viability, however, with different values of LC50 (median lethal concentration). SEM analysis showed an analog of enamel alterations with decreasing pH, increasing exposure time, and increasing HP concentration. Bleaching agents containing a low HP concentration are considered to be effective and to have less damaging effects on enamel and tested cells.

Micro-CT evaluation of marginal and internal fit of cemented polymer infiltrated ceramic network material crowns manufactured after conventional and digital impressions.

PURPOSE: Purpose of this study was to evaluate the accuracy of fit of cemented polymer infiltrated ceramic network (PICN) material crowns manufactured after digital and conventional impression techniques using micro computed tomography (CT). Furthermore to determine the cement space volume and porosities in the cement layer. METHODS: A molar typodont tooth was prepared for PICN material crowns and replicated thirty times. The dies were randomly divided into three groups of 10 specimens each according to the impression technique: 3M True Definition Scanner (TDS), cara TRIOS (Trios) and Impregum Penta Soft (Impregum). PICN material crowns were milled for each specimen from Vita Enamic blocks and cemented on their respective dies. The absolute marginal discrepancy (AMD), internal fit (IG), total cement space volume (TVC) and marginal porosities (VP) were measured using Micro-CT. RESULTS: Mean and standard deviations values in µm for the AMD were: TDS 140.1 (28.4); Trios 253.7 (56.8); Impregum 220.2 (101.1). IG values in µm: TDS 173.1 (27.7); Trios 222.2 (22.4); Impregum 211.6 (55.9). TVC in mm3: TDS 19.82 (2.9); Trios 23.67 (2.01); Impregum 23.77 (5.09). VP in mm3: TDS 0.38 (0.09); Trios 0.36 (0.10); Impregum 0.51 (0.31). CONCLUSIONS: TDS group showed significantly better marginal and internal fit than the Trios group. No difference of the parameters was detected between the Impregum and both digital groups which implies that the digital impression technique is suitable in the manufacturing process of PICN material crowns.

Proliferation, behavior, and differentiation of osteoblasts on surfaces of different microroughness.

OBJECTIVES: Titanium surface roughness is recognized as an important parameter influencing osseointegration. However, studies concerning the effect of well-defined surface topographies of titanium surfaces on osteoblasts have been limited in scope. In the present study we have investigated how Ti surfaces of different micrometer-scale roughness influence proliferation, migration, and differentiation of osteoblasts in-vitro. METHODS: Titanium replicas with surface roughnesses (Ra) of approximately 0, 1, 2, and 4µm were produced and MG-63 osteoblasts were cultured on these surfaces for up to 5 days. The effect of surface micrometer-scale roughness on proliferation, migration in time-lapse microscopy experiments, as well as the expression of alkaline phosphatase, osteocalcin, vascular-endothelial growth factor (VEGF), osteoprotegerin (OPG), and receptor activator of nuclear factor kappa-B ligand (RANKL) were investigated. RESULTS: Proliferation of MG-63 cells was found to decrease gradually with increasing surface roughness. However, the highest expression of alkaline phosphatase, osteocalcin and VEGF was observed on surfaces with Ra values of approximately 1 and 2µm. Further increase in surface roughness resulted in decreased expression of all investigated parameters. The cell migration speed measured in time-lapse microscopy experiments was significantly lower on surfaces with a Ra value of about 4µm, compared to those with lower roughness. No significant effect of surface roughness on the expression of OPG and RANKL was observed. SIGNIFICANCE: Thus, surfaces with intermediate Ra roughness values of 1-2µm seem to be optimal for osteoblast differentiation. Neither proliferation nor differentiation of osteoblasts appears to be supported by surfaces with higher or lower Ra values.

Cytotoxicity of post and core composites as a function of environmental conditions.

OBJECTIVES: In the revised version of ISO 7405 there are so far no detailed recommendations concerning temperature and humidity during specimen production for light curing and chemically setting dental materials. The main objective of the present study was to observe if different environmental conditions during specimen production influence cytotoxicity and degree of conversion of four post and core composite materials and to investigate if cytotoxicity of post and core materials is influenced by their corresponding bonding substances. METHODS: Specimens of four different post and core composite materials (LuxaCore - Dual, Core X-Flow, Flow White and MultiCore Flow) were produced in a climate test chamber at 23°C/50% relative humidity or 37°C/95% relative humidity and were dual-cured or self-cured, with or without their corresponding bonding substances. Specimens were added to cell cultures immediately after production or after preincubation for 7 days. Specimens were incubated with L-929 fibroblasts for 72h and cell numbers determined by a flow cytometer. FTIR spectroscopic measurements of post and core materials were performed at the same temperature conditions as for the cytotoxicity assay (23°C or 37°C). RESULTS: Dual-cured specimens of all post and core composites exhibited less cytotoxicity under both environmental conditions than self-cured specimens. All self-cured specimens manufactured at 37°C/95% showed less cytotoxicity than specimens produced at 23°C/50%. All dual-cured specimens showed similar cytotoxicity at both environmental conditions. After 7 days of preincubation most dual-cured specimens produced at 23°C/50% showed less cytotoxicity than self-cured specimens (with the exception of Flow White). Compared to fresh specimens, 7-day aged specimens of most materials showed reduced cytotoxicity. Materials already showing low cytotoxicity as fresh specimens did not further reduce their cytotoxicity after 7 days of preincubation. For dual-cured materials the degree of conversion was higher compared to self-cured materials. SIGNIFICANCE: Different temperatures during specimen production have an impact on cytotoxicity and degree of conversion of dual-curing composite materials. Detailed recommendations for standardization concerning environmental conditions during specimen production are required.

One-year evaluation of two hybrid composites placed in a randomized-controlled clinical trial.

OBJECTIVE: The aim of this prospective randomized-controlled clinical trial is to assess the long-term performance of two direct composite resins in posterior teeth. This study provides a survey of the one-year results. MATERIALS AND METHODS: A total of 1805 restorations were placed by students in stress-bearing Class I/II cavities (including cuspal-coverage) in molars and premolars in 456 patients. Clinical evaluation was performed at baseline and after one year using modified USPHS criteria. The restorations in each patient were performed either with Ceram X/Prime&Bond NT or Tetric Ceram/Optibond Solo Plus. RESULTS: After one year 528 fillings with Ceram X and 580 with Tetric Ceram were available for evaluation of substance loss, contact point, color match, marginal staining, marginal adaptation, secondary caries and radiographic examination (if necessary). This represents a recall rate of 61.18% (279 patients). The failure rate per material was 5.3% in the Ceram X group and 6.1% in the Tetric Ceram group. Most of the failures were associated with marginal adaptation/integrity of the filling. A significant influence on the occurrence of a failure was observed for the number of treated teeth per patient, the age of the patient, the mesio-distal extension of the restoration and the tooth position. Gender, material, a previous root canal treatment, the bucco-lingual extension of the filling or cuspal-coverage did not significantly influence the failure rate. Patients attending the first recall were significantly older and had more fillings than patients not attending. CONCLUSIONS: In a group of Class I/II restorations (including cuspal-coverage), there was no significant difference in failure rates between ormocer-based and bis-GMA-based restorative systems after one year. A previous root canal treatment had no negative influence on the failure rate. A longer observation period is indicated to get clear evidence of the long-term performance of these composite resin systems.

The angiogenic behaviors of human umbilical vein endothelial cells (HUVEC) in co-culture with osteoblast-like cells (MG-63) on different titanium surfaces.

OBJECTIVES: Interaction between osteogenesis and angiogenesis plays an important role in implant osseointegration. In the present study we investigated the influence of titanium surface properties on the angiogenic behaviors of endothelial cells grown in direct contact co-culture with osteoblasts. METHODS: Human umbilical vein endothelial cells (HUVECs) and osteoblast-like cells (MG-63 cells) were grown in direct co-culture on the following titanium surfaces: acid-etched (A), hydrophilic A (modA), coarse-gritblasted and acid-etched (SLA) and hydrophilic SLA (SLActive). Cell proliferation was evaluated by cell counting combined with flow cytometry. The expression of von Willebrand Factor (vWF), thrombomodulin (TM), endothelial cell protein C receptor (EPCR), E-Selectin, as well as vascular endothelial growth factor (VEGF) receptors Flt-1 and KDR in HUVECs and VEGF in MG-63 were measured by qPCR. The dynamic behavior of endothelial cells was recorded by time-lapse microscopy. RESULTS: Proliferation of HUVECs was highest on A, followed by SLA, modA and SLActive surfaces. The expression of vWF, TM, EPCR, E-Selectin and Flt-1 in HUVECs was significantly higher on A than on all other surfaces. The expression of KDR in HUVECs grown on A surface was below detection limit. VEGF expression in MG-63 cells was significantly higher on SLActive vs SLA and modA vs A surfaces. Time-lapse microscopy revealed that HUVECs moved quickest and formed cell clusters earlier on A surface, followed by SLA, modA and SLActive surface. CONCLUSIONS: In co-culture conditions, proliferation and expression of angiogenesis associated genes in HUVECs are promoted by smooth hydrophobic Ti surface, which is in contrast to previous mono-culture studies.

Initial attachment, subsequent cell proliferation/viability and gene expression of epithelial cells related to attachment and wound healing in response to different titanium surfaces.

OBJECTIVES: A tight seal between the epithelium and the dental implant surface is required to prevent bacterial inflammation and soft tissue recession and therefore to demonstrate a long-term success. Surface hydrophilicity was recently shown to promote osseointegration. The aim of this study was to investigate the influence of surface hydrophilicity in combination with surface topography of Ti implant surfaces on the behavior and activation/differentiation of epithelial cells using a set of in vitro experiments mimicking the implant-soft tissue contact. METHODS: Hydrophobic acid-etched (A) and coarse-grit-blasted, acid-etched (SLA) surfaces and hydrophilic acid-etched (modA) and modSLA surfaces were produced. The behavior of an oral squamous cell carcinoma cell line (HSC-2) grown on all surfaces was compared through determination of cell attachment and proliferation/viability (CCK-8 and MTT assay), time-lapse microscopy of fluorescence labeled cells and determination of gene expression by real time polymerase chain reaction. RESULTS: Within the surfaces with similar wettability cell spreading and cell movements observed by time-lapse microscopy after one day of incubation were most pronounced on smoother (A and modA) surfaces compared to rougher (SLA and modSLA) surfaces. Within the surfaces with similar roughness the hydrophilic surfaces (modA and modSLA) showed more cell spreading and cell activity compared to the hydrophobic surfaces (A and SLA). The relative gene expressions of cytokeratin14, integrin α6, integrin ß4, vinculin, transforming growth factor (TGF)-ß, TGF-ß1, and TGF-ß3 were decreased in HSC-2 on all four types of Ti surfaces compared to control surfaces (tissue culture polystyrene; p<0.01) and there was no significant difference of gene expression on the four different implant-surfaces. SIGNIFICANCE: We have demonstrated that for proliferation and spreading of HSC-2 cells the smoother and hydrophilic surface is optimal (modA). These results suggest that surface hydrophilicity might positively influence the epithelial seal around dental implants. All tested titanium surfaces downregulate cell attachment, cell proliferation, expression of adhesion promoters, and cytokines involved in wound healing in HSC-2 cells compared to control surfaces.

Microleakage after thermocycling of cemented crowns--a meta-analysis.

OBJECTIVES: Microleakage testing of dental materials is a commonly accepted evaluation technique of margin integrity. Thermocycling has been utilized by many researchers to study the influence of temperature extremes on the marginal gap of cemented restorations. The aim of this investigation was to analyze microleakage data on cemented crowns, published in the dental literature until Dec 2009, to identify methodological factors that might potentially affect the results of in vitro microleakage tests and to compare the results. METHODS: The following databases were included: Ovid MEDLINE(R) In-Process & Other Non-Indexed Citations and Ovid MEDLINE(R) 1950 to Present, Ovid-MEDLINE(R) 1950 to Present with Daily Update, EMBASE, EBM Reviews - Cochrane Database of Systematic Reviews and Pub Med. The search was limited to articles in English, French, Italian and German published until the end of 2009. Classical reviews, comments, animal studies, in vivo articles and studies investigating restorative materials or milk teeth were excluded. 33 different studies were finally selected. The studies were entered in a database and compared using selected literature criteria: sample, restoration procedures, thermocycling and mechanical cycling, evaluation method. For statistical analysis only 16 studies could be applied. RESULTS: It was not possible to make a quantitative synthesis of most of the data, due to the heterogeneity of the studies concerning methods, treatment and outcome variables. Comparing the main groups of materials (ceramics, gold alloys and base metal alloys), no significant difference in the proportion of teeth without microleakage was found. Furthermore no significant difference in the proportion of teeth showing microleakage less than two third of the wall or teeth showing microleakage including the entire wall was found. Using the mean values in the meta-analysis instead of the proportions does not change the results. Confidence intervals could only be calculated for two materials (gold alloy, metal alloy). No difference between materials was found. SIGNIFICANCE: Comparison of the results from different studies is critical, since there are no generally accepted standards for experimental parameters, such as type and concentration of the storage solution, time of storage, temperature during storage, type and duration of thermal cycling and/or mechanical cycling, and the scoring criteria. There is lack of standardization of experimental conditions, which would ensure confidence in the studies and would further allow better comparability of various results.

Setting kinetics and shrinkage of self-adhesive resin cements depend on cure-mode and temperature.

OBJECTIVE: To investigate the influence of curing mode and temperature on the shrinkage kinetics of self-adhesive resin cements in comparison to a conventional multi-step resin cement. METHODS: The shrinkage of self-adhesive resin cements Maxcem Elite (MX), Speedcem (SPC), Smartcem2 (SMC), iCem (IC) and RelyX Unicem (RX) and Nexus Third Generation (NX3) as a multi-step resin cement was measured continuously for 1h using the bonded disk method. All materials were tested with dual-curing (dc) and self-curing (sc) mode. All measurements (n=5 per group) were conducted at room temperature (23°C) as well as at body temperature (37°C). Shrinkage time constants were obtained from a simple exponential growth model. Data were statistically analyzed by ANOVA and the p-values were adjusted for multiplicity according to Hothorn et al. (2008) using the R-package "multcomp". RESULTS: Shrinkages ranged between 1.84 (RX sc23) and 7.09 (IC sc37). The curing-mode changing from sc to dc had the dominant effect for several materials, especially RX, both on final shrinkage and time constant for setting. Temperature increase had an effect on setting and shrinkage for all materials except RX. Final shrinkage for SPC, SMC and NX3 was statistically equivalent (p>0.05). SIGNIFICANCE: The 3-fold variation in final shrinkage for these materials is significant for clinical material selection. Light curing can lead to a 10-fold increase in the rate of setting. A self-adhesive universal resin cement (RX) had the lowest shrinkage in the groups examined.