3D-printed zeolite 13X-Strontium chloride units as ammonia carriers.

The selective catalytic reduction (SCR) system in automobiles using urea solution as a source of NH3 suffers from solid deposit problems in pipelines and poor efficiency during engine startup. Although direct use of high pressure NH3 is restricted due to safety concerns, which can be overcome by using solid sorbents as NH3 carrier. Strontium chloride (SrCl2) is considered the best sorbent due to its high sorption capacity; however, challenges are associated with the processing of stable engineering structures due to extraordinary volume expansion during the NH3 sorption. This study reports the fabrication of a novel structure consisting of a zeolite cage enclosing the SrCl2 pellet (SPZC) through extrusion-based 3D printing (Direct Ink Writing). The printed SPZC structure demonstrated steady sorption of NH3 for 10 consecutive cycles without significant uptake capacity and structural integrity loss. Furthermore, the structure exhibited improved sorption and desorption kinetics than pure SrCl2. The synergistic effect of zeolite as physisorbent and SrCl2 as chemisorbent in the novel composite structure enabled the low-pressure (<0.4 bar) and high-pressure (>0.4 bar) NH3 sorption, compared to pure SrCl2, which absorbed NH3 at pressures above 0.4 bar. Regeneration of SPZC composite sorbent under evacuation showed that 87.5% percent of NH3 was desorbed at 20 °C. Thus, the results demonstrate that the rationally designed novel SPZC structure offers safe and efficient storage of NH3 in the SCR system and other applications.

A review on activated carbon modifications for the treatment of wastewater containing anionic dyes.

Polluted water resources, particularly those polluted with industrial effluents' dyes, are carcinogenic and hence pose a severe threat to sustainable and longstanding worldwide development. Meanwhile, adsorption is a promising process for polluted/wastewater treatment. In particular, activated carbon (AC) is popular among various wastewater treatment adsorbents, especially in the organic contaminants' remediation in wastewater. Hence, the AC's synthesis from degradable and non-degradable resources, the carbon activation involved in the AC synthesis, and the AC's modification to cutting-edge and effective materials have been modern-research targets in recent years. Likewise, the main research focuses worldwide have been the salient AC characteristics, such as its surface chemistry, porosity, and enhanced surface area. Notably, various modified-AC synthesis methods have been employed to enhance the AC's potential for improved contaminants-removal. Hence, we critically analyze the different modified ACs (with enhanced (surface) functional groups and textural properties) of their capacity to remove different-natured anionic dyes in wastewater. We also discuss the corresponding AC modification techniques, the factors affecting the AC properties, and the modifying agents' influence on the AC's morphological/adsorptive properties. Finally, the AC research of future interest has been proposed by identifying the current AC research gaps, especially related to the AC's application in wastewater treatment.

KIT-6 induced mesostructured TiO2 for photocatalytic degradation of methyl blue.

In this study, titania/silica nanocomposite and mesoporous TiO2 (m-TiO2) photocatalysts are developed by KIT-6 template via a sol-gel approach. The synthesized photocatalysts are characterized by XRD, EDX, SEM, Raman, PL, and UV-vis DRS analysis techniques. The as-synthesized series revealed a high surface area, smaller size, a greater number of accessible active sites, and enhanced light-harvesting capability. The m-TiO2 photocatalysts' charge recombination capability was curiously inferior to the rest of as-synthesized TiO2/KIT-6 nanocomposite materials. The band-gap of as-synthesized materials were suitable for their activity in UV light irradiations. It was pragmatic that the photocatalytic degradation efficiency of m-TiO2 photocatalysts was superior as compared to that of commercial TiO2 photocatalyst under UV light irradiations, owing to the synergistic outcome of the anatase phase and a greater number of accessible active-sites availability as a result of high surface area. Moreover, the m-TiO2 was critically evaluated by investigating various parameters affecting the photocatalytic degradation reaction of MB including the effect of irradiation time, pH, catalyst dosage, and dye concentration. The m-TiO2, 45wt% composite material and commercial-TiO2 exhibited 99.27, 91.20, and 84.67% degradation of methyl blue in 50 min, respectively. Finally, the m-TiO2 exhibited excellent recyclability with negligible loss of activity performance.

A phase conversion method to anchor ZIF-8 onto a PAN nanofiber surface for CO2 capture.

Polyacrylonitrile (PAN) nanofibers were prepared by electrospinning and coated with zeolitic imidazolate framework-8 (ZIF-8) by a phase conversion growth method and investigated for CO2 capture. The PAN nanofibers were pre-treated with NaOH, and further coated with zinc hydroxide, which was subsequently converted into ZIF-8 by the addition of 2-methyl imidazolate. In the resulting flexible ZIF-8/PAN composite nanofibers, ZIF-8 loadings of up to 57 wt% were achieved. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDS) showed the formation of evenly distributed submicron-sized ZIF-8 crystals on the surface of the PAN nanofibers with sizes between 20 and 75 nm. X-ray photoelectron spectroscopy (XPS) and carbon-13 nuclear magnetic resonance (13C NMR) investigations indicated electrostatic interactions and hydrogen bonds between the ZIF-8 structure and the PAN nanofiber. The ZIF-8/composite nanofibers showed a high BET surface area of 887 m2 g-1. CO2 adsorption isotherms of the ZIF-8/PAN composites revealed gravimetric CO2 uptake capacities of 130 mg g-1 (at 298 K and 40 bar) of the ZIF-8/PAN nanofiber and stable cyclic adsorption performance.

Carbon Nanotubes Incorporated Z-Scheme Assembly of AgBr/TiO2 for Photocatalytic Hydrogen Production under Visible Light Irradiations.

Photocatalytic H2 production is a promising strategy toward green energy and alternative to carbon-based fuels which are the root cause of global warming and pollution. In this study, carbon nanotubes (CNTs) incorporated Z-scheme assembly of AgBr/TiO2 was developed for photocatalytic H2 production under visible light irradiations. Synthesized photocatalysts were characterized through transmission electron microscope (TEM), X-ray photoelectron spectra (XPS), X-ray diffractometer (XRD), Fourier transform infrared (FTIR), photoluminescence spectra (PL), Brunauer Emmet-Teller(BET), and UV-vis spectroscopy analysis techniques. The composite photocatalysts exhibited a H2 production of 477 ppm which was three-folds higher than that produced by TiO2. The good performance was attributed to the strong interaction of three components and the reduced charge recombination, which was 89 and 56.3 times lower than the TiO2 and AgBr/TiO2. Furthermore, the role of surface acidic and basic groups was assessed and the photocatalytic results demonstrated the importance of surface functional groups. In addition, the composites exhibited stability and reusability for five consecutive cycles of reaction. Thus, improved performance of the photocatalyst was credited to the CNTs as an electron mediator, surface functional groups, higher surface area, enhanced charge separation and extended visible light absorption edge. This work provides new development of Z-scheme photocatalysts for sustainable H2 production.