Prediction and Measurement of the Damping Ratios of Laminated Polymer Composite Plates.

Laminated composites materials are mostly used in dynamically loaded structures. The design of these structures with finite element packages is focused on vibrations, elastic deformations and failure control. Damping is often neglected because of its assumed secondary importance and also because of dearth of information on relevant material properties. This trend is prone to change as it is now realised that damping plays an increasingly important role in vibration comfort, noise radiation and crash simulations. This paper shows in a first step how to identify the orthotropic elastic and damping properties of single layer fibre-reinforced composite material sheets using a new extended version of the Resonalyser procedure. The procedure is based on the elastic-viscoelastic correspondence principle and uses a mixed numerical experimental method. In a subsequent step, the complex laminate stiffness values are computed using the identified single layer material properties. To validate this approach, the modal damping ratios of arbitrary laminated plates of different materials at several resonance frequencies are predicted and experimentally verified.

The quasi-harmonic ultrasonic polar scan for material characterization: experiment and numerical modeling.

Conventionally, the ultrasonic polar scan (UPS) records the amplitude or time-of-flight in transmission using short ultrasonic pulses for a wide range of incidence angles, resulting in a fingerprint of the critical bulk wave angles of the material at the insonified spot. Here, we investigate the use of quasi-harmonic ultrasound (bursts) in a polar scan experiment, both experimentally and numerically. It is shown that the nature of the fingerprint drastically changes, and reveals the positions of the leaky Lamb angles. To compare with experiments, both plane wave and bounded beam simulations have been performed based on the recursive stiffness matrix method. Whereas the plane wave computations yield a pure Lamb wave angle fingerprint, this is no longer valid for the more realistic case of a bounded beam. The experimental recordings are fully supported by the bounded beam simulations. To complement the traditional amplitude measurement, experimental and numerical investigations have been performed to record, predict and analyze the phase of the transmitted ultrasonic beam. This results in the conceptual introduction of the 'phase polar scan', exposing even more intriguing and detailed patterns. In fact, the combination of the amplitude and the phase polar scan provides the complete knowledge about the complex transmission coefficient for every possible angle of incidence. This comprehensive information will be very valuable for inverse modeling of the local elasticity tensor based on a single UPS experiment. Finally, the UPS method has been applied for the detection of an artificial delamination. Compared to the pulsed UPS, the quasi-harmonic UPS (both the amplitude and phase recording) shows a superior sensitivity to the presence of a delamination.

Pitfalls in the experimental recording of ultrasonic (backscatter) polar scans for material characterization.

The ultrasonic polar scan (UPS), either in transmission, reflection or backscatter mode, is a promising non-destructive testing technique for the characterization of composites, providing information about the mechanical anisotropy, the viscoelastic damping, the surface roughness, and more. At present, the technique is merely being used for qualitative purposes. The limited quantitative exploration and use of the technique can be primarily ascribed to limitations of current theoretical models as well as the difficulty to perform accurate, and more importantly, reproducible UPS experiments. Over the last years, we have identified several potential pitfalls in the experimental implementation of the technique which severely deteriorate the accurateness and reproducibility of a UPS. In this paper, we make an inventory of the most important difficulties, illustrate each of them by a real experiment and present a feasible mediation, either numerical or experimental in nature. Once the experimental set-up is fine-tuned to overcome these pitfalls, it is expected that the recording of high-level UPS experiments, in combination with numerical computations, will facilitate the technique to become a fully quantitative non-destructive characterization method.

The effect of material modeling on finite element analysis of human breast biomechanics.

PURPOSE: Finite element analysis has been used extensively in the study of biomechanical modeling of the breast. However, issues regarding the complexity of material models and the influences of geometric boundary conditions on the accuracy of a breast Finite Element (FE) model are still under debate. This work demonstrates the importance of material modeling in FE models of the breast. METHODS: A simple hemispherical geometry is used to model the shape of a human breast. Different material models are being investigated to accurately model changes in terms of displacement, stress, and reaction forces distribution. RESULTS: The results obtained using nonlinear material models are compared with those obtained employing their linear approximation. Results have shown that differences, in terms of displacement, ranging between 20% and more than 80%, may occur and that large differences are present in terms of maximum principal stresses when the displacement is correctly approximated. CONCLUSIONS: This study clearly shows that, in a FE model, simulating large deformations material modeling strongly influences the accuracy of the solution.