RESUMO
The work is aimed at studying the impact resistance of epoxy oligomer matrices (EO) modified with polysulfone (PSU) or polyethersulfone (PES) and glass fibers reinforced plastics (GFRP) based on them under low-velocity impact conditions. The concentration dependences of strength and fracture energy of modified matrices and GFRP were determined. It has been determined that the type of concentration curves of the fracture energy of GFRP depends on the concentration and type of the modifying polymer. It is shown that strength σ and fracture energy EM of thermoplastic-modified epoxy matrices change little in the concentration range from 0 to 15 wt.%. However, even with the introduction of 20 wt.% PSU into EO, the strength increases from 164 MPa to 200 MPa, and the fracture energy from 32 kJ/m2 to 39 kJ/m2. The effect of increasing the strength and fracture energy of modified matrices is retained in GFRP. The maximum increase in shear strength (from 72 MPa to 87 MPa) is observed for GFRP based on the EO + 15 wt.% PSU matrix. For GFRP based on EO + 20 wt.% PES, the shear strength is reduced to 69 MPa. The opposite effect is observed for the EO + 20 wt.% PES matrix, where the strength value decreases from 164 MPa to 75 MPa, and the energy decreases from 32 kJ/m2 to 10 kJ/m2. The reference value for the fracture energy of GFRP 615 is 741 kJ/m2. The maximum fracture energy for GFRP is based on EO + 20 wt.% PSU increases to 832 kJ/m2 for GFRP based on EO + 20 wt.% PES-up to 950 kJ/m2. The study of the morphology of the fracture surfaces of matrices and GFRP confirmed the dependence of impact characteristics on the microstructure of the modified matrices and the degree of involvement in the process of crack formation. The greatest effect is achieved for matrices with a phase structure "thermoplastic matrix-epoxy dispersion." Correlations between the fracture energy and strength of EO + PES matrices and GFRP have been established.
RESUMO
HYPOTHESIS: Hydrogels based on cellulose nanocrystals (CNC) have attracted great interest because of their sustainability, biocompatibility, mechanical strength and fibrillar structure. Gelation of colloidal particles can be induced by the introduction of polymers. Existing examples include gels based on CNC and derivatives of cellulose or poly(vinyl alcohol), however, gel structure and their application for extrusion printing were not shown. Hence, we rationalize formation of colloidal gels based on mixture of poly(N-isopropylacrylamide) (PNIPAM) and CNC and control their structure and mechanical properties by variation of components ratio. EXPERIMENTS: State diagram for colloidal system based on mixture of PNIPAM and CNC were established at 25 and 37 °C. Biocompatibility, fiber diameter and rheological properties of the gels were studied for different PNIPAM/CNC ratio. FINDINGS: We show that depending on the ratio between PNIPAM and CNC, colloidal system could be in sol or gel state at 25 °C and at gel state or phase separated at 37 °C. Physically crosslinked hydrogels were thermosensitive and could reversibly change it transparency from translucent to opaque in biologically relevant temperature range. These colloidal hydrogels were biocompatible, had fibrillar structure and demonstrate shear-thinning behavior, which makes them a promising material for bioapplications related to extrusion printing.
RESUMO
An epoxy resin modified with polysulfone (PSU) and active diluent furfuryl glycidyl ether (FGE) was studied. Triethanolaminotitanate (TEAT) and iso-methyltetrahydrophthalic anhydride (iso-MTHPA) were used as curing agents. It is shown that during the curing of initially homogeneous mixtures, heterogeneous structures are formed. The type of these structures depends on the concentration of active diluent and the type of hardener. The physico-mechanical properties of the hybrid matrices are determined by the structure formed. The maximum resistance to a growing crack is provided by structures with a thermoplastic-enriched matrix-interpenetrating structures. The main mechanism for increasing the energy of crack propagation is associated with the implementation of microplasticity of extended phases enriched in polysulfone and their involvement in the fracture process.
RESUMO
A methodology for synthesizing a wide range of dumbbell-shaped, graft and bottlebrush polymers with all-siloxane nature (without carbosilane linkers) is suggested. These macroarchitectures are synthesized from SiOH-containing compounds-silanol (Et3 SiOH) and siloxanol dendrons of the first and second generations, with various peripheral substituents (Me or Et)-and from linear siloxanes comprising terminal and internal SiH groups by the Piers-Rubinsztajn reaction. Products and key building blocks are obtained in yields up to 95%. These polymers are heat and frost-resistant siloxanes. As it turns out, the product physical properties are determined not only by the macromolecular structure, the linear chain length, the size and frequency of branched pendant, but also by the type of peripheral substituents-Me or Et-in the pendant. Thus, the viscosity of the graft polymers with branched pendant groups comprising peripheral Me-groups is more than ≈3-5 fold lower than that of analogous polymers with peripheral Et-groups.
Assuntos
Polímeros , Siloxanas , Estrutura Molecular , ReologiaRESUMO
The mutual solubility of epoxy oligomer with polysulfone (PSU) and polyethersulfone (PES) was studied by optical interferometry. Additionally, phase diagrams (PDs) were plotted and their evolution during the curing process was shown. The phase structures of modified hardened systems, as well as their tensile strengths, elastic moduli, and crack resistance, have been studied by scanning electron microscopy and physico-mechanical techniques. The effect of initial components' mutual solubility on the phase structure and, subsequently, on the physico-mechanical properties of the composite material is shown. Differences in the structure and properties of the cured modified compositions depending on the type of PD (with Upper Critical Solution Temperature (UCST) for PSU and Lower Critical Solution Temperature (LCST) for PES) of the initial components are shown.