Examining the Workability, Mechanical, and Thermal Characteristics of Eco-Friendly, Structural Self-Compacting Lightweight Concrete Enhanced with Fly Ash and Silica Fume.

This study compares the workability, mechanical, and thermal characteristics of structural self-compacting lightweight concrete (SCLWC) formulations using pumice aggregate (PA), expanded perlite aggregate (EPA), fly ash (FA), and silica fume (SF). FA and SF were used as partial substitutes for cement at a 10% ratio in various mixes, impacting different aspects: According to the obtained results, FA enhanced the workability but SF reduced it, while SF improved the compressive and splitting tensile strengths more than FA. EPA, used as a fine aggregate alongside PA, decreased the workability, compressive strength, and splitting tensile strength compared to the control mix (K0). The thermal properties were altered by FA and SF similarly, while EPA notably reduced the thermal conductivity coefficients. The thermal conductivity coefficients (TCCs) of the K0-K4 SCLWC mixtures ranged from 0.275 to 0.364 W/mK. K0 had a TCC of 0.364 W/mK. With 10% FA, K1 achieved 0.305 W/mK; K2 with 10% SF reached 0.325 W/mK. K3 and K4, using EPA instead of PA, showed significantly lower TCC values: 0.275 W/mK and 0.289 W/mK, respectively. FA and SF improved the thermal conductivity compared to K0, while EPA further reduced the TCC values in K3 and K4 compared to K1 and K2. The compressive strength (CS) values of the K0-K4 SCLWC mixtures at 7 and 28 days reveal notable trends. Using 10% FA in K1 decreased the CS at both 7 days (12.16 MPa) and 28 days (22.36 MPa), attributed to FA's gradual pozzolanic activity. Conversely, K2 with SF showed increased CS at 7 days (17.88 MPa) and 28 days (29.89 MPa) due to SF's rapid pozzolanic activity. Incorporating EPA into K3 and K4 reduced the CS values compared to PA, indicating EPA's lower strength contribution due to its porous structure.

Ethics and responsibility in biohybrid robotics research.

The industrial revolution of the 19th century marked the onset of an era of machines and robots that transformed societies. Since the beginning of the 21st century, a new generation of robots envisions similar societal transformation. These robots are biohybrid: part living and part engineered. They may self-assemble and emerge from complex interactions between living cells. While this new era of living robots presents unprecedented opportunities for positive societal impact, it also poses a host of ethical challenges. A systematic, nuanced examination of these ethical issues is of paramount importance to guide the evolution of this nascent field. Multidisciplinary fields face the challenge that inertia around collective action to address ethical boundaries may result in unexpected consequences for researchers and societies alike. In this Perspective, we i) clarify the ethical challenges associated with biohybrid robotics, ii) discuss the need for and elements of a potential governance framework tailored to this technology; and iii) propose tangible steps toward ethical compliance and policy formation in the field of biohybrid robotics.

Improvements in Wear and Corrosion Resistance of Ti-W-Alloyed Gray Cast Iron by Tailoring Its Microstructural Properties.

The improved wear and corrosion resistance of gray cast iron (GCI) with enhanced mechanical properties is a proven stepping stone towards the longevity of its versatile industrial applications. In this article, we have tailored the microstructural properties of GCI by alloying it with titanium (Ti) and tungsten (W) additives, which resulted in improved mechanical, wear, and corrosion resistance. The results also show the nucleation of the B-, D-, and E-type graphite flakes with the A-type graphite flake in the alloyed GCI microstructure. Additionally, the alloyed microstructure demonstrated that the ratio of the pearlite volume percentage to the ferrite volume percentage was improved from 67/33 to 87/13, whereas a reduction in the maximum graphite length and average grain size from 356 ± 31 µm to 297 ± 16 µm and 378 ± 18 µm to 349 ± 19 µm was detected. Consequently, it improved the mechanical properties and wear and corrosion resistance of alloyed GCI. A significant improvement in Brinell hardness, yield strength, and tensile strength of the modified microstructure from 213 ± 7 BHN to 272 ± 8 BHN, 260 ± 3 MPa to 310 ± 2 MPa, and 346 ± 12 MPa to 375 ± 7 MPa was achieved, respectively. The substantial reduction in the wear rate of alloyed GCI from 8.49 × 10-3 mm3/N.m to 1.59 × 10-3 mm3/N.m resulted in the upgradation of the surface roughness quality from 297.625 nm to 192.553 nm. Due to the increase in the corrosion potential from -0.5832 V to -0.4813 V, the impedance of the alloyed GCI was increased from 1545 Ohm·cm2 to 2290 Ohm·cm2. On the basis of the achieved experimental results, it is suggested that the reliability of alloyed GCI based on experimentally validated microstructural compositions can be ensured during the operation of plants and components in a severe wear and corrosive environment. It can be predicted that the proposed alloyed GCI components are capable of preventing the premature failure of high-tech components susceptible to a wear and corrosion environment.

The influence of nanosunflower ash and nanowalnut shell ash on sustainable lightweight self-compacting concrete characteristics.

The absence of biodegradability exhibited by plastics is a matter of significant concern among environmentalists and scientists on a global scale. Therefore, it is essential to figure out potential pathways for the use of recycled plastics. The prospective applications of its utilisation in concrete are noteworthy. The use of recycled plastic into concrete, either as a partial or complete substitution for natural aggregates, addresses the issue of its proper disposal besides contributing to the preservation of natural aggregate resources. Furthermore, the use of agricultural wastes has been regarded as a very promising waste-based substance in the industry of concrete manufacturing, with the aim of fostering the creation of an environmentally sustainable construction material. This paper illustrates the impact of nano sunflower ash (NSFA) and nano walnut shells ash (NWSA) on durability (compressive strength and density after exposure to 800 °C and sulphate attack), mechanical properties (flexural, splitting tensile and compressive strength) and fresh characteristics (slump flow diameter, T50, V-funnel flow time, L-box height ratio, segregation resistance and density) of lightweight self-compacting concrete (LWSCC). The waste walnut shells and local Iraqi sunflower were calcinated at 700 ± 50 °C for 2 h and milled for 3 h using ball milling for producing NSFA and NWSA. The ball milling succeeded in reducing the particle size lower than 75 nm for NSFA and NWSA. The preparation of seven LWSCC concrete mixes was carried out to obtain a control mix, three mixtures were created using 10%, 20% and 30% NWSA, and the other three mixtures included 10%, 20% and 30% NSFA. The normal weight coarse aggregates were substituted by the plastic waste lightweight coarse aggregate with a ratio of 75%. The fresh LWSCC passing capacity, segregation resistance, and filling capability were evaluated. The hardened characteristics of LWSCC were evaluated by determining the flexural and splitting tensile strength at 7, 14 and 28 days and the compressive strength was measured at 7, 14, 28 and 60 days. Dry density and compressive strength were measured after exposing mixes to a temperature of 800 °C for 3 h and immersed in 10% magnesium sulphate attack. The results demonstrated that the LWSCC mechanical characteristics were reduced when the percentages of NWSA and NSFA increased, except for 10% NWSA substitution ratio which had an increase in splitting tensile strength test and similar flexural strength test to the control mixture. A minor change in mechanical characteristics was observed within the results of LWSCC dry density and compressive strength incorporating various NSFA and NWSA` contents after exposing to temperature 800 °C and immersed in 10% magnesium sulphate attack. Furthermore, according to the findings, it is possible to use a combination of materials consisting of 10-20% NSFA and 10-20% NWSA to produce LWSCC.

Assessment of the properties of concrete containing artificial green geopolymer aggregates by cold bonding pelletization process.

Recently, the usage of a cold-bonded method in the production of artificial green geopolymer coarse aggregates (GCA) has been crucial from an economic and environmental perspective because the sintering method consumes an enormous quantity of energy and generates a significant quantity of pollutants. This research investigated the manufacture of GCA via cold-bonded pelletization using two distinct industrial byproducts (GGBFS and FA) via a new and simpler pelletization technology. Three different binders were used to produce three distinct types of GCAs as partial replacements for natural coarse aggregate (NCA) at varying replacement rates (0%, 25%, 50%, and 75%). The first group used ground-granulated blast furnace slag, while the second used GGBFS with perlite, and the third used FA with perlite. An alkaline activator was commonly used with all three groups. The physical and mechanical properties of three distinct varieties of GCA were recorded. The results indicated that the mechanical and chemical properties of three different types of GCAs were nearly identical to those of natural aggregate, with the exception of their increased water absorption. According to the findings, the recommended mixtures were suitable for usage in the construction industry. The results indicated that the ratio of all investigated attributes declined as the number of GCAs increased. In contrast, lightweight concrete can be obtained at a ratio of GCA (FA with perlite) equal to 75%, where unit weight, compressive, splitting tensile, flexural, and water absorption strengths were 1.87 gm/cm3, 20.2 MPa, 1.8 MPa, 8 MPa, and 6.0%, respectively (FA with perlite).

Harnessing the supremacy of MEG3 LncRNA to defeat gastrointestinal malignancies.

Evidence suggests that long non-coding RNAs (lncRNAs) play a pivotal role in the carcinogenesis and progression of various human malignancies including gastrointestinal malignancies. This comprehensive review reports the functions and mechanisms of the lncRNA maternally expressed gene 3 (MEG3) involved in gastrointestinal malignancies. It summarizes its roles in mediating the regulation of cellular proliferation, apoptosis, migration, invasiveness, epithelial-to-mesenchymal transition, and drug resistance in several gastrointestinal cancers such as colorectal cancer, gall bladder cancer, pancreatic cancer, gastric cancer, esophageal cancer, cholangiocarcinoma, gastrointestinal stromal tumors and most importantly, hepatocellular carcinoma. In addition, the authors briefly highlight its implicated mechanistic role and interactions with different non-coding RNAs and oncogenic signaling cascades. This review presents the rationale for developing non coding RNA-based anticancer therapy via harnessing the power of MEG3 in gastrointestinal malignancies.

Nuclear deformation regulates YAP dynamics in cancer associated fibroblasts.

Cells cultured on stiff 2D substrates exert high intracellular force, resulting in mechanical deformation of their nuclei. This nuclear deformation (ND) plays a crucial role in the transport of Yes Associated Protein (YAP) from the cytoplasm to the nucleus. However, cells in vivo are in soft 3D environment with potentially much lower intracellular forces. Whether and how cells may deform their nuclei in 3D for YAP localization remains unclear. Here, by culturing human colon cancer associated fibroblasts (CAFs) on 2D, 2.5D, and 3D substrates, we differentiated the effects of stiffness, force, and ND on YAP localization. We found that nuclear translocation of YAP depends on the degree of ND irrespective of dimensionality, stiffness and total force. ND induced by the perinuclear force, not the total force, and nuclear membrane curvature correlate strongly with YAP activation. Immunostained slices of human tumors further supported the association between ND and YAP nuclear localization, suggesting ND as a potential biomarker for YAP activation in tumors. Additionally, we conducted quantitative analysis of the force dynamics of CAFs on 2D substrates to construct a stochastic model of YAP kinetics. This model revealed that the probability of YAP nuclear translocation, as well as the residence time in the nucleus follow a power law. This study provides valuable insights into the regulatory mechanisms governing YAP dynamics and highlights the significance of threshold activation in YAP localization. STATEMENT OF SIGNIFICANCE: Yes Associated Protein (YAP), a transcription cofactor, has been identified as one of the drivers of cancer progression. High tumor stiffness is attributed to driving YAP to the nucleus, wherein it activates pro-metastatic genes. Here we show, using cancer associated fibroblasts, that YAP translocation to the nucleus depends on the degree of nuclear deformation, irrespective of stiffness. We also identified that perinuclear force induced membrane curvature correlates strongly with YAP nuclear transport. A novel stochastic model of YAP kinetics unveiled a power law relationship between the activation threshold and persistence time of YAP in the nucleus. Overall, this study provides novel insights into the regulatory mechanisms governing YAP dynamics and the probability of activation that is of immense clinical significance.

Mind In Vitro Platforms: Versatile, Scalable, Robust, and Open Solutions to Interfacing with Living Neurons.

Motivated by the unexplored potential of in vitro neural systems for computing and by the corresponding need of versatile, scalable interfaces for multimodal interaction, an accurate, modular, fully customizable, and portable recording/stimulation solution that can be easily fabricated, robustly operated, and broadly disseminated is presented. This approach entails a reconfigurable platform that works across multiple industry standards and that enables a complete signal chain, from neural substrates sampled through micro-electrode arrays (MEAs) to data acquisition, downstream analysis, and cloud storage. Built-in modularity supports the seamless integration of electrical/optical stimulation and fluidic interfaces. Custom MEA fabrication leverages maskless photolithography, favoring the rapid prototyping of a variety of configurations, spatial topologies, and constitutive materials. Through a dedicated analysis and management software suite, the utility and robustness of this system are demonstrated across neural cultures and applications, including embryonic stem cell-derived and primary neurons, organotypic brain slices, 3D engineered tissue mimics, concurrent calcium imaging, and long-term recording. Overall, this technology, termed "mind in vitro" to underscore the computing inspiration, provides an end-to-end solution that can be widely deployed due to its affordable (>10× cost reduction) and open-source nature, catering to the expanding needs of both conventional and unconventional electrophysiology.

Prevalence of the HLA-B*5701 Allele and Abacavir Hypersensitivity in Saudi HIV Patients: A Multicenter Study.

Introduction Human immunodeficiency virus (HIV) incidence and prevalence are increasing in Saudi Arabia, with a total prevalence of 12,000 in 2020. Treatment of HIV patients includes multiple regimens that may involve abacavir (ABC), which is a potent drug for treating HIV and can be used as a single or combined pill. Unfortunately, its use was limited by the known associated hypersensitivity reaction (HSR). A worldwide literature review over the past decades reported that the incidence of ABC-related HSR is 5-8%. Methods The study was a cross-sectional multicentric study involving five governmental hospitals in Saudi Arabia and included all HIV patients who were following in these centers. Results Out of 3082 patients, 1293 were tested for HLA-B*5701. The prevalence for ABC-HSR is 1.59%, with variability among the five hospitals, with the highest in King Fahad Hospital in Hafuf (KFH-H) at 4.00% and the lowest in Dammam Medical Complex (DMC) at 0.49%. In previous studies, HLA-B*5701 associated with ABC-HSR varied among different ethnic groups. Our study showed that two patients developed ABC-HSR clinically while they were both negative for HLA-B*5701. Conclusion The fact that patients with negative genetic testing are still at risk of developing ABC-HSR makes continuing screening for HLA-B*5701 status essential, as the consequences of missing such a life-threatening HSR could be detrimental.

Synapses without tension fail to fire in an in vitro network of hippocampal neurons.

Neurons in the brain communicate with each other at their synapses. It has long been understood that this communication occurs through biochemical processes. Here, we reveal that mechanical tension in neurons is essential for communication. Using in vitro rat hippocampal neurons, we find that 1) neurons become tout/tensed after forming synapses resulting in a contractile neural network, and 2) without this contractility, neurons fail to fire. To measure time evolution of network contractility in 3D (not 2D) extracellular matrix, we developed an ultrasensitive force sensor with 1 nN resolution. We employed Multi-Electrode Array and iGluSnFR, a glutamate sensor, to quantify neuronal firing at the network and at the single synapse scale, respectively. When neuron contractility is relaxed, both techniques show significantly reduced firing. Firing resumes when contractility is restored. This finding highlights the essential contribution of neural contractility in fundamental brain functions and has implications for our understanding of neural physiology.

Analyzing the Effects of Nano-Titanium Dioxide and Nano-Zinc Oxide Nanoparticles on the Mechanical and Durability Properties of Self-Cleaning Concrete.

The goal of this paper is to investigate the impact of nano-materials on the mechanical and electrochemical properties of self-cleaning concrete. Nano-titanium dioxide and nano-zinc oxide were used as additives for this purpose. Additionally, a comparative study on the effect of using these materials on the self-cleaning concrete's characteristics was conducted. The dosages of nano-titanium dioxide (nps-TiO2) and nano-zinc oxide (nps-ZnO) used were 0, 0.5, 1, 1.5, 2, and 2.5% and 0, 1, 2, and 3% of the weight of the cement, respectively. The results showed that the optimum compressive strength and the lowest corrosion rate were fulfilled at 2.5% of nps-TiO2 and 1% of nps-ZnO, and using 2.5% of nps-TiO2 achieved the highest improvement in the corrosion rate. However, 1% for nps-TiO2 mixtures and 1% for nps-ZnO mixtures were the best ratios for flexural strength. On the other hand, for the corrosion rate, the samples were tested at 2 and 6 months. When nps-TiO2 and nps-ZnO samples were compared to the control sample, 2.5% and 1% of nps-TiO2 and nps-ZnO, respectively, showed the largest improvement in resistance to corrosion. Also, the self-cleaning property of the samples containing nano-materials (nps-TiO2 and nps-ZnO) was tested. As the results illustrated, the self-cleaning property of the samples was increased over time due to photocatalytic degradation. Furthermore, the results of the photocatalytic tests showed that nps-TiO2 samples outperformed nps-ZnO samples overall.

The Efficacy of Educational Interventions in Improving School Teachers' Knowledge of Attention Deficit Hyperactivity Disorder.

BACKGROUND: Well-trained primary school teachers should be competent in recognizing attention deficit hyperactivity disorder (ADHD) in students and be able to assist in providing care and support. OBJECTIVES: This study intends to assess primary school teachers' knowledge of ADHD and evaluate the effectiveness of a short-term educational intervention.  Methods: A quasi-experimental quantitative study was conducted among primary school teachers in Jazan, Saudi Arabia. A two-hour educational intervention was designed and run in six schools using a specific knowledge rating scale before and after the application of the intervention.  Results: A total of 150 primary school teachers were included in this study, of which 64% were males, 51.3% were in the age group of 40-49 years, and 28% had teaching experience of more than 20 years. Regarding ADHD knowledge, the pre-intervention knowledge of the general criteria, symptoms and diagnosis, and treatment was considered adequate in 3.3%, 16.7%, and 2.7% of the participants, respectively, which improved post-intervention to 22%, 54.7%, and 19.3%, respectively. There was a significant association between the pre-intervention knowledge of the general criteria and the gender and between the knowledge of symptoms and diagnosis and the attendance of ADHD workshop by the participants. Also, there was a significant association between the participants' age, residence experience, attendance of ADHD workshops, and the general criteria and treatment domains. CONCLUSIONS:  Most primary school teachers in Jazan have insufficient knowledge of ADHD. Using a knowledge improvement intervention can substantially improve the teachers' knowledge. Therefore, it is necessary to incorporate thoughtful knowledge improvement programs into the educational curricula for teachers.

Mechanosensitive changes in the expression of genes in colorectal cancer-associated fibroblasts.

Most solid tumors become stiff with progression of cancer. Cancer Associated Fibroblasts (CAFs), most abundant stromal cells in the tumor microenvironment (TME), are known to mediate such stiffening. While the biochemical crosstalk between CAFs and cancer cells have been widely investigated, it is not clear if and how CAFs in stiffer TME promote metastatic progression. To gather insights into the process, we controlled the mechanical stiffness of the substrates and collected gene expression data with human colorectal CAFs. We cultured human primary CAFs on 2D polyacrylamide hydrogels with increasing elastic modulus (E) of 1, 10 and 40 kPa, and performed genome-wide transcriptome analyses in these cells to identify expression levels of ~16000 genes. The high-quality RNAseq results can be an excellent data-source for bioinformatic analysis for identifying novel pathways and biomarkers in cancer development and metastatic progression. With thorough analysis and accurate interpretation, this data may help researchers understand the role of mechanical stiffness of the TME in CAF-cancer cell crosstalk.

π-Electron-Extended Triazine-Based Covalent Organic Framework as Photocatalyst for Organic Pollution Degradation and H2 Production from Water.

Herein, we report the efficient preparation of π-electron-extended triazine-based covalent organic framework (TFP-TPTPh COF) for photocatalysis and adsorption of the rhodamine B (RhB) dye molecule, as well as for photocatalytic hydrogen generation from water. The resultant TFP-TPTPh COF exhibited remarkable porosity, excellent crystallinity, high surface area of 724 m2 g-1, and massive thermal stability with a char yield of 63.41%. The TFP-TPTPh COF demonstrated an excellent removal efficiency of RhB from water in 60 min when used as an adsorbent, and its maximum adsorption capacity (Qm) of 480 mg g-1 is among the highest Qm values for porous polymers ever to be recorded. In addition, the TFP-TPTPh COF showed a remarkable photocatalytic degradation of RhB dye molecules with a reaction rate constant of 4.1 × 10-2 min-1 and an efficiency of 97.02% under ultraviolet-visible light irradiation. Furthermore, without additional co-catalysts, the TFP-TPTPh COF displayed an excellent photocatalytic capacity for reducing water to generate H2 with a hydrogen evolution rate (HER) of 2712 µmol g-1 h-1. This highly active COF-based photocatalyst appears to be a useful material for dye removal from water, as well as solar energy processing and conversion.

Astrocyte-mediated Transduction of Muscle Fiber Contractions Synchronizes Hippocampal Neuronal Network Development.

Exercise supports brain health in part by enhancing hippocampal function. The leading hypothesis is that muscles release factors when they contract (e.g., lactate, myokines, growth factors) that enter circulation and reach the brain where they enhance plasticity (e.g., increase neurogenesis and synaptogenesis). However, it remains unknown how the muscle signals are transduced by the hippocampal cells to modulate network activity and synaptic development. Thus, we established an in vitro model in which the media from contracting primary muscle cells (CM) is applied to developing primary hippocampal cell cultures on a microelectrode array. We found that the hippocampal neuronal network matures more rapidly (as indicated by synapse development and synchronous neuronal activity) when exposed to CM than regular media (RM). This was accompanied by a 4.4- and 1.4-fold increase in the proliferation of astrocytes and neurons, respectively. Further, experiments established that factors released by astrocytes inhibit neuronal hyper-excitability induced by muscle media, and facilitate network development. Results provide new insight into how exercise may support hippocampal function by regulating astrocyte proliferation and subsequent taming of neuronal activity into an integrated network.

Smart biomaterials for enhancing cancer therapy by overcoming tumor hypoxia: a review.

Hypoxia is a distinctive feature of most solid tumors due to insufficient oxygen supply of the abnormal vasculature, which cannot work with the demands of the fast proliferation of cancer cells. One of the main obstacles to limiting the efficacy of cancer medicines is tumor hypoxia. Thus, oxygen is a vital parameter for controlling the efficacy of different types of cancer therapy, such as chemotherapy (CT), photodynamic therapy (PDT), photothermal therapy (PTT), immunotherapy (IT), and radiotherapy (RT). Numerous technologies have attracted much attention for enhancing oxygen distribution in humans and improving the efficacy of cancer treatment. Such technologies include treatment with hyperbaric oxygen therapy (HBO), delivering oxygen by polysaccharides (e.g., cellulose, gelatin, alginate, and silk) and other biocompatible synthetic polymers (e.g., PMMA, PLA, PVA, PVP and PCL), decreasing oxygen consumption, producing oxygen in situ in tumors, and using polymeric systems as oxygen carriers. Herein, this review provides an overview of the relationship between hypoxia in tumor cells and its role in the limitation of different cancer therapies alongside the numerous strategies for oxygen delivery using polysaccharides and other biomaterials as carriers and for oxygen generation.

Disorder to order transition in cell-ECM systems mediated by cell-cell collective interactions.

Cells in functional tissues execute various collective activities to achieve diverse ordered processes including wound healing, organogenesis, and tumor formation. How a group of individually operating cells initiate such complex collective processes is still not clear. Here, we report that cells in 3D extracellular matrix (ECM) initiate collective behavior by forming cell-ECM network when the cells are within a critical distance from each other. We employed compaction of free-floating (FF) 3D collagen gels with embedded fibroblasts as a model system to study collective behavior and found a sharp transition in the amount of compaction as a function of cell-cell distance, reminiscent of phase transition in materials. Within the critical distance, cells remodel the ECM irreversibly, and form dense collagen bridges between each other resulting in the formation of a network. Beyond the critical distance, cells exhibit Brownian dynamics and only deform the matrix reversibly in a transient manner with no memory of history, thus maintaining the disorder. Network formation seems to be a necessary and sufficient condition to trigger collective behavior and a disorder-to order transition. STATEMENT OF SIGNIFICANCE: Macroscopic compaction of in vitro collagen gels is mediated by collective mechanical interaction of cells. Previous studies on cell-induced ECM compaction suggest the existence of a critical cell density and phase transition associated with this phenomenon. Cell-mediated mechanical remodeling and global compaction of ECM has mostly been studied at steady state. Our study reveals a link between a transition in cell dynamics and material microstructure as cells collectively compact collagen gels. It underscores the significance of temporal evolution of these cell-ECM systems in understanding the mechanism of such collective action and provides insights on the process from a mechanistic viewpoint. These insights can be valuable in understanding dynamic pathological processes such as, cancer progression and wound healing, as well as engineering biomaterials and regenerative tissue mimics.

Antitumor/anti-angiogenesis efficacy of epigallocatechin gallate nanoformulated with antioxidant in melanoma.

Aim: Epigallocatechin gallate (EGCG) derived from green tea has poor stability; therefore, to enhance its bioavailability and anticancer efficiency, we synthesized three different nanoformulations. We hypothesized that these three nanoformulations of EGCG (nano-EGCG) would enhance EGCG's stability and improve its anticancer and antiangiogenic activity against melanoma compared with free EGCG. Methods: We prepared nano-EGCG using a copolymerization method with the UV blocker ZnO and the antioxidants lycopene and olive oil. Results: The different nano-EGCG formulation exhibited improved EGCG stability and greater suppression of melanoma growth than free EGCG. Nanoformulation preparation methods efficiently prevented the loss of EGCG activity and are a favorable approach for the treatment of melanoma. Conclusion: Nano-EGCG formulations had enhanced stability and produced greater suppression of melanoma tumor growth and angiogenesis compared with free EGCG.