Assessing soil erosion risk in a peri-urban catchment of the Lake Victoria basin.

Soil erosion and sedimentation contribute to deteriorating water quality, adverse alterations in basin hydrology and overall ecosystem biogeochemistry. Thus, understanding soil erosion patterns in catchments is critical for conservation planning. This study was conducted in a peri-urban Inner Murchison Bay (IMB) catchment on the northern shores of Lake Victoria since most soil erosion studies in Sub-Saharan Africa have been focused on rural landscapes. The study sought to identify sediment sources by mapping erosion hotspots using the revised universal soil loss equation (RUSLE) model in appendage with field walks. RUSLE model was built in ArcGIS 10.5 software with factors including: rainfall erosivity, soil erodibility, slope length and steepness, land cover and support practices. The model was run, producing an erosion risk map and field assessments conducted to ground-truth findings and identify other hotspots. The percentage areas for RUSLE modelled erosion rates were: 66.8% for 0-2 t ha-1 year-1; 10.8% for 2-5 t ha-1 year-1; 10.1% for 5-10 t ha-1 year-1; 9% for 10-50 t ha-1 year-1 and 3.3% for 50-100 t ha-1 year-1. Average erosion risk was 7 t ha-1 year-1 and the total watershed erosion risk was 197,400 t year-1, with croplands and steep areas (slope factor > 20) as the major hotspots (> 5 t ha-1 year-1). Field walks revealed exposed soils, marrum (gravel) roads and unlined drainage channels as other sediment sources. This study provided the first assessment of erosion risk in this peri-urban catchment, to serve as a basis for identifying mitigation priorities. It is recommended that tailored soil and water conservation measures be integrated into physical planning, focusing on identified non-conventional hotspots to ameliorate sediment pollution in Lake Victoria.

Physicochemical characterization and heavy metals analysis from industrial discharges in Upper Awash River Basin, Ethiopia.

The recent expansion of industries in Addis Ababa is causing additional environmental pollution through wastewater discharges; this is becoming a critical concern. Addis Ababa is located in the upper Awash River basin, and is the main source of industrial pollutants to the river. In this study, physicochemical parameters, nutrients and heavy metal content of wastewaters released from 16 factories, 6 tanneries, 6 beverages and 4 diverse factories, and the Akaki-Kality central wastewater treatment plant in Addis Ababa, were sampled to assess the level of pollutants. Heavy metals were determined using inductively coupled plasma optical emission spectroscopy (ICP-OES). Analysis of nutrients were conducted using Palintest Photometer. Physicochemical characteristics were measured either in situ using a portable micro meter or in the laboratory. Among the measured physicochemical properties, critical issues were observed with electrical conductivity, total dissolved solids and total hardness. Effluents from all of the tanneries, and a number of other factories, were found at levels higher than the maximum limits of various guideline standards. In addition, samples from two of the tanneries (T1 and T5), two beverage factories (B3 and B6) and the central wastewater treatment plant showed elevated concentrations of PO4 3-, which violated the limit (10 mg/l) set by Environmental Protection Agency of Ethiopia (ETHEPA). The two tanneries (T1 and T5) also contained higher SO4 2- than the guideline limit of 1000 mg/l. On the other hand, only one factory, one brewery (B3), exhibited NO3 - above the standard limit of 20 mg/l. Whereas NH3, NH4 +, Cl-, S2- and NO2 - were within the limits in all of the samples. Severe pollution was found in wastewaters from tanneries, where half of them (T1, T5 and T6) contained Cr beyond the maximum limit of 2000 µg/l. Furthermore, a third of the tanneries (T1 and T5) and a beverage factory (B5) contained Fe, Mn, Zn and Cu, higher than the ETHEPA limits of 10000, 5000, 5000 and 2000 µg/l, respectively. Waste disposal from factories without proper treatment can cause great harm to the local people and the environment. Hence, the results of this study call for regulatory bodies to pay close attention to factories, particularly tanneries, in Addis Ababa in implementing adequate treatments of their wastewater discharges.

Functional Links between Biomass Production and Decomposition of Vetiver (Chrysopogon zizanioides) Grass in Three Australian Soils.

Plant roots are primary factors to contribute to surface and deep soil carbon sequestration (SCS). Perennial grasses like vetiver produce large and deep root system and are likely to contribute significantly to soil carbon. However, we have limited knowledge on how root and shoot decomposition differ and their contribution to SCS. This study examined biomass production and relative decomposition of vetiver which was grown under glasshouse conditions. Subsequently the biomass incubated for 206 days, and the gas analysed using ANCA-GSL. The results confirmed large shoot and root production potential of 161 and 107 Mg ha−1 (fresh) and 67.7 and 52.5 Mg ha−1 (dry) biomass, respectively with 1:1.43 (fresh) and 1:1.25 (dry) production ratio. Vetiver roots decomposed more rapidly in the clay soil (p < 0.001) compared with the shoots, which could be attributed to the lower C:N ratio of roots than the shoots. The large root biomass produced does indeed contribute more to the soil carbon accumulation and the faster root decomposition is crucial in releasing the carbon in the root exudates and would also speed up its contribution to stable SOM. Hence, planting vetiver and similar tropical perennial grasses on degraded and less fertile soils could be a good strategy to rehabilitate degraded soils and for SCS.