Extending the low-temperature operation of sodium metal batteries combining linear and cyclic ether-based electrolyte solutions.

Nonaqueous sodium-based batteries are ideal candidates for the next generation of electrochemical energy storage devices. However, despite the promising performance at ambient temperature, their low-temperature (e.g., < 0 °C) operation is detrimentally affected by the increase in the electrolyte resistance and solid electrolyte interphase (SEI) instability. Here, to circumvent these issues, we propose specific electrolyte formulations comprising linear and cyclic ether-based solvents and sodium trifluoromethanesulfonate salt that are thermally stable down to -150 °C and enable the formation of a stable SEI at low temperatures. When tested in the Na||Na coin cell configuration, the low-temperature electrolytes enable long-term cycling down to -80 °C. Via ex situ physicochemical (e.g., X-ray photoelectron spectroscopy, cryogenic transmission electron microscopy and atomic force microscopy) electrode measurements and density functional theory calculations, we investigate the mechanisms responsible for efficient low-temperature electrochemical performance. We also report the assembly and testing between -20 °C and -60 °C of full Na||Na3V2(PO4)3 coin cells. The cell tested at -40 °C shows an initial discharge capacity of 68 mAh g-1 with a capacity retention of approximately 94% after 100 cycles at 22 mA g-1.

Electrocatalytic CO2 reduction on earth abundant 2D Mo2C and Ti3C2 MXenes.

Mo2C and Ti3C2 MXenes were investigated as earth-abundant electrocatalyts for the CO2 reduction reaction (CO2RR). Mo2C and Ti3C2 exhibited faradaic efficiencies of 90% (250 mV overpotential) and 65% (650 mV overpotential), respectively, for the reduction of CO2 to CO in acetonitrile using an ionic liquid electrolyte. The use of ionic liquid 1-ethyl-2-methylimidazolium tetrafluoroborate as an electrolyte in organic solvent suppressed the competing hydrogen evolution reaction. Density functional theory (DFT) calculations suggested that the catalytic active sites are oxygen vacancy sites on both MXene surfaces. Also, a spontaneous dissociation of adsorbed COOH species to a water molecule and adsorbed CO on Mo2C promote the CO2RR.

Distinct Nanoscale Interphases and Morphology of Lithium Metal Electrodes Operating at Low Temperatures.

While Li-ion batteries are known to fail at temperatures below -20 °C, very little is known regarding the low-temperature behavior of next-generation high-capacity electrode materials. The lithium metal anode is of particular interest for high-energy battery chemistries, but improved understanding of and control over its electrochemical and nanoscale interfacial behavior in diverse conditions is necessary. Here, we investigate lithium deposition/stripping, morphology evolution, and solid-electrolyte interphase (SEI) structure and properties down to -80 °C using an ether-based electrolyte (DOL/DME). As temperature is reduced, we find that the morphology of deposited lithium is significantly altered. Furthermore, cryogenic transmission electron microscopy coupled with vacuum-transfer X-ray photoelectron spectroscopy reveal that the SEI exhibits different structure, chemistry, thickness, and conductive properties at lower temperatures. These results show that Li is promising for batteries operating under extreme conditions, and the distinct nanoscale evolution of Li electrodes at different temperatures must be considered when designing high-energy batteries.

Antimicrobial Properties of 2D MnO2 and MoS2 Nanomaterials Vertically Aligned on Graphene Materials and Ti3C2 MXene.

Two-dimensional (2D) nanomaterials have attracted considerable attention in biomedical and environmental applications due to their antimicrobial activity. In the interest of investigating the primary antimicrobial mode-of-action of 2D nanomaterials, we studied the antimicrobial properties of MnO2 and MoS2, toward Gram-positive and Gram-negative bacteria. Bacillus subtilis and Escherichia coli bacteria were treated individually with 100 µg/mL of randomly oriented and vertically aligned nanomaterials for ∼3 h in the dark. The vertically aligned 2D MnO2 and MoS2 were grown on 2D sheets of graphene oxide, reduced graphene oxide, and Ti3C2 MXene. Measurements to determine the viability of bacteria in the presence of the 2D nanomaterials performed by using two complementary techniques, flow cytometry, and fluorescence imaging showed that, while MnO2 and MoS2 nanosheets show different antibacterial activities, in both cases, Gram-positive bacteria show a higher loss in membrane integrity. Scanning electron microscopy images suggest that the 2D nanomaterials, which have a detrimental effect on bacteria viability, compromise the cell wall, leading to significant morphological changes. We propose that the peptidoglycan mesh (PM) in the bacterial wall is likely the primary target of the 2D nanomaterials. Vertically aligned 2D MnO2 nanosheets showed the highest antimicrobial activity, suggesting that the edges of the nanosheets were likely compromising the cell walls upon contact.

Systematic Doping of Cobalt into Layered Manganese Oxide Sheets Substantially Enhances Water Oxidation Catalysis.

The effect on the electrocatalytic oxygen evolution reaction (OER) of cobalt incorporation into the metal oxide sheets of the layered manganese oxide birnessite was investigated. Birnessite and cobalt-doped birnessite were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and conductivity measurements. A cobalt:manganese ratio of 1:2 resulted in the most active catalyst for the OER. In particular, the overpotential (η) for the OER was 420 mV, significantly lower than the η = 780 mV associated with birnessite in the absence of Co. Furthermore, the Tafel slope for Co/birnessite was 81 mV/dec, in comparison to a Tafel slope of greater than 200 mV/dec for birnessite. For chemical water oxidation catalysis, an 8-fold turnover number (TON) was achieved (h = 70 mmol of O2/mol of metal). Density functional theory (DFT) calculations predict that cobalt modification of birnessite resulted in a raising of the valence band edge and occupation of that edge by holes with enhanced mobility during catalysis. Inclusion of extra cobalt beyond the ideal 1:2 ratio was detrimental to catalysis due to disruption of the layered structure of the birnessite phase.

Cobalt Intercalated Layered NiFe Double Hydroxides for the Oxygen Evolution Reaction.

We present a combined experimental and theoretical study to demonstrate that the electrocatalytic activity of NiFe layered double hydroxides (NiFe LDHs) for the oxygen evolution reaction (OER) can be significantly enhanced by systematic cobalt incorporation using coprecipitation and/or intercalation. Electrochemical measurements show that cobalt modified NiFe LDH possesses an enhanced activity for the OER relative to pristine NiFe LDH. The Co-modified NiFe LDH exhibits overpotentials in the range of 290-322 mV (at 10 mA cm-2), depending on the degree of cobalt content. The best catalyst, cobalt intercalated NiFe LDH achieved a current density of 10 mA cm-2 at an overpotential of ∼265 mV (compared to 310 mV for NiFe LDH), with a near unity (99%) faradaic efficiency and long-term stability. Density functional theory calculations revealed that enhanced activity of Co-modified NiFe LDH could be attributed to the ability of Co to tune the electronic structure of the NiFe LDH so that optimal binding of OER reaction intermediates could be achieved.

Redox properties of birnessite from a defect perspective.

Birnessite, a layered-structure MnO2, is an earth-abundant functional material with potential for various energy and environmental applications, such as water oxidation. An important feature of birnessite is the existence of Mn(III) within the MnO2 layers, accompanied by interlayer charge-neutralizing cations. Using first-principles calculations, we reveal the nature of Mn(III) in birnessite with the concept of the small polaron, a special kind of point defect. Further taking into account the effect of the spatial distribution of Mn(III), we propose a theoretical model to explain the structure-performance dependence of birnessite as an oxygen evolution catalyst. We find an internal potential step which leads to the easy switching of the oxidation state between Mn(III) and Mn(IV) that is critical for enhancing the catalytic activity of birnessite. Finally, we conduct a series of comparative experiments which support our model.

Effect of Interlayer Spacing on the Activity of Layered Manganese Oxide Bilayer Catalysts for the Oxygen Evolution Reaction.

We investigated the dependence of the electrocatalytic activity for the oxygen evolution reaction (OER) on the interlayer distance of five compositionally distinct layered manganese oxide nanostructures. Each individual electrocatalyst was assembled with a different alkali metal intercalated between two nanosheets (NS) of manganese oxide to form a bilayer structure. Manganese oxide NS were synthesized via the exfoliation of a layered material, birnessite. Atomic force microscopy was used to determine the heights of the bilayer catalysts. The interlayer spacing of the supported bilayers positively correlates with the size of the alkali cation: NS/Cs+/NS > NS/Rb+/NS > NS/K+/NS > NS/Na+/NS > NS/Li+/NS. The thermodynamic origins of these bilayer heights were investigated using molecular dynamics simulations. The overpotential (η) for the OER correlates with the interlayer spacing; NS/Cs+/NS has the lowest η (0.45 V), while NS/Li+/NS exhibits the highest η (0.68 V) for OER at a current density of 1 mA/cm2. Kinetic parameters (η and Tafel slope) associated with NS/Cs+/NS for the OER were superior to that of the bulk birnessite phase, highlighting the structural uniqueness of these nanoscale assemblies.

Nickel Confined in the Interlayer Region of Birnessite: an Active Electrocatalyst for Water Oxidation.

We report a synthetic method to enhance the electrocatalytic activity of birnessite for the oxygen evolution reaction (OER) by intercalating Ni(2+) ions into the interlayer region. Electrocatalytic studies showed that nickel (7.7 atomic %)-intercalated birnessite exhibits an overpotential (η) of 400 mV for OER at an anodic current of 10 mA cm(-2) . This η is significantly lower than the η values for birnessite (η≈700 mV) and the active OER catalyst ß-Ni(OH)2 (η≈550 mV). Molecular dynamics simulations suggest that a competition among the interactions between the nickel cation, water, and birnessite promote redox chemistry in the spatially confined interlayer region.

Oxidation of arsenite to arsenate on birnessite in the presence of light.

The effect of simulated solar radiation on the oxidation of arsenite [As(III)] to arsenate [As(V)] on the layered manganese oxide, birnessite, was investigated. Experiments were conducted where birnessite suspensions, under both anoxic and oxic conditions, were irradiated with simulated solar radiation in the presence of As(III) at pH 5, 7, and 9. X-ray absorption spectroscopy (XAS) was used to determine the nature of the adsorbed product on the surface of the birnessite. The oxidation of As(III) in the presence of birnessite under simulated solar light irradiation occurred at a rate that was faster than in the absence of light at pH 5. At pH 7 and 9, As(V) production was significantly less than at pH 5 and the amount of As(V) production for a given reaction time was the same under dark and light conditions. The first order rate constant (kobs) for As(III) oxidation in the presence of light and in the dark at pH 5 were determined to be 0.07 and 0.04 h-1, respectively. The As(V) product was released into solution along with Mn(II), with the latter product resulting from the reduction of Mn(IV) and/or Mn(III) during the As(III) oxidation process. Post-reaction XAS analysis of As(III) exposed birnessite showed that arsenic was present on the surface as As(V). Experimental results also showed no evidence that reactive oxygen species played a role in the As(III) oxidation process.

Copper-Intercalated Birnessite as a Water Oxidation Catalyst.

We report a synthetic method to increase the catalytic activity of birnessite toward water oxidation by intercalating copper in the interlayer region of the layered manganese oxide. Intercalation of copper, verified by XRD, XPS, ICP, and Raman spectroscopy, was accomplished by exposing a suspension of birnessite to a Cu(+)-bearing precursor molecule that underwent disproportionation in solution to yield Cu(0) and Cu(2+). Electrocatalytic studies showed that the Cu-modified birnessite exhibited an overpotential for water oxidation of ∼490 mV (at 10 mA/cm(2)) and a Tafel slope of 126 mV/decade compared to ∼700 mV (at 10 mA/cm(2)) and 240 mV/decade, respectively, for birnessite without copper. Impedance spectroscopy results suggested that the charge transfer resistivity of the Cu-modified sample was significantly lower than Cu-free birnessite, suggesting that Cu in the interlayer increased the conductivity of birnessite leading to an enhancement of water oxidation kinetics. Density functional theory calculations show that the intercalation of Cu(0) into a layered MnO2 model structure led to a change of the electronic properties of the material from a semiconductor to a metallic-like structure. This conclusion from computation is in general agreement with the aforementioned impedance spectroscopy results. X-ray photoelectron spectroscopy (XPS) showed that Cu(0) coexisted with Cu(2+) in the prepared Cu-modified birnessite. Control experiments using birnessite that was decorated with only Cu(2+) showed a reduction in water oxidation kinetics, further emphasizing the importance of Cu(0) for the increased activity of birnessite. The introduction of Cu(0) into the birnessite structure also increased the stability of the electrocatalyst. At a working current of 2 mA, the Cu-modified birnessite took ∼3 times longer for the overpotential for water oxdiation to increase by 100 mV compared to when Cu was not present in the birnessite.