RESUMO
The present study aimed to extract nanocellulose (NC) from sugarcane bagasse agricultural waste through a chemical method (sulfuric acid hydrolysis and ultrasonication). Subsequently, the nanocellulose product was conjugated with polylysine (NC-PL) and assessed for its efficacy in reducing the toxicity of Fumonisin B1 (FB1), a mycotoxin produced by fungi commonly found in corn, wheat, and other grains. Experimental results confirmed the successful conjugation of NC and PL, as evidenced by FTIR peaks at 1635 and 1625 cm-1 indicating amide I and amide II vibrations in polylysine (PL). SEM analysis revealed a larger size due to PL coating, consistent with DLS results showing the increased size and positive charge (38.0 mV) on the NC-PL surface. Moreover, the effect of FB1 adsorption by NC and NC-PL was evaluated at various concentrations (0-200,000 µg/mL). NC-PL demonstrated the ability to adsorb FB1 at concentrations of 2000, 20,000, and 200,000 µg/mL, with adsorption efficiencies of 94.4-100%. Human hepatocellular carcinoma (HepG2) cells were utilized to assess NC and NC-PL cytotoxic effects. This result is a preliminary step towards standardizing results for future studies on their application as novel FB1 binders in food, food packaging, and functional feeds.
RESUMO
Bamboo cellulose fiber (BF)-reinforced epoxy (EP) composites were fabricated with BF subjected to plasma treatment using argon (Ar), oxygen (O2), and nitrogen (N2) gases. Optimal mechanical properties of the EP/BF composites were achieved with BFs subjected to 30 min of plasma treatment using Ar. This is because Ar gas improved the plasma electron density, surface polarity, and BF roughness. Flexural strength and flexural modulus increased with O2 plasma treatment. Scanning electron microscopy images showed that the etching of the fiber surface with Ar gas improved interfacial adhesion. The water contact angle and surface tension of the EP/BF composite improved after 10 min of Ar treatment, owing to the compatibility between the BFs and the EP matrix. The Fourier transform infrared spectroscopy results confirmed a reduction in lignin after treatment and the formation of new peaks at 1736 cm-1, which indicated a reaction between epoxy groups of the EP and carbon in the BF backbone. This reaction improved the compatibility, mechanical properties, and water resistance of the composites.
RESUMO
The objective of this study was to characterize the properties of cellulose and CMC synthesized from young and mature coconut coir with different bleaching times (bleaching for the first time; 1 BT, bleaching for a second time; 2 BT, and bleaching for the third time; 3 BT) using hydrogen peroxide (H2O2). The surface morphology, structural information, chemical compositions, and crystallinity of both cellulose and CMC were determined. H2O2 bleaching can support delignification by reducing hemicellulose and lignin, as evidenced by FTIR showing a sharp peak at wave number 1260 cm-1. The cellulose and CMC from coconut coir can be more dispersed and have greater functional characteristics with increasing bleaching times due to the change in accessibility of hydroxyl groups in the structure. The CMC diffraction patterns of coconut coir after the bleaching process showed the destruction of the crystalline region of the original cellulose. The SEM images showed that the surface of CMC was smoother than that of cellulose. The CMCy had a higher water holding capacity (WHC) compared to the CMCm as the bleaching can increase interaction between the polymer and water molecules. Therefore, the best quality of CMC corresponds to CMCy. Based on these findings, bleaching time has a strong effect on the functional properties of cellulose and CMC from coconut coir.
RESUMO
Using vegetable oils as a plasticizer or processing aid in green rubber products is becoming popular due to environmental concerns. However, differences in vegetable oil processing result in varying amounts of low-molecular-weight (low-MW) free fatty acids (FFAs) in their composition, which range from 2% to 30%. This research investigated how the properties of silica-filled styrene butadiene rubber (SBR) and butadiene rubber (BR) blends were affected by the presence of FFAs in palm oil (PO). The rubber compounds containing a 70/30 SBR/BR blend, 30 phr of silica, and 2 phr of bis-(3-triethoxysilylpropyl) tetrasulfide (TESPT), and the vulcanizing agents were prepared and tested. The PO content was kept constant at 20 phr, while the number of FFAs, i.e., lauric acid (LA), palmitic acid (PA), and oleic acid (OA), in PO varied from 10-30%. The viscosity, dynamic mechanical properties, morphology, cure characteristics, and mechanical properties of the rubber blend were then measured. Regardless of the FFA types, increasing FFA content in PO decreased scorch time, cure time, minimum torque, and viscosity. As the FFA content increased, the torque difference and crosslink density also increased, which led to higher hardness, modulus, tensile strength, and abrasion resistance. The FFA types had a slight effect on the vulcanizate properties, even though LA showed slightly better mechanical properties than PA and OA. The results reveal that FFAs in PO not only improve processability but also function as a co-activator in silica-filled sulfur-vulcanized SBR/BR blend compounds.
RESUMO
Cellulose from different species of bamboo (Thyrsostachys siamesi Gamble, Dendrocalamus sericeus Munro (DSM), Bambusa logispatha, and Bambusa sp.) was converted to cellulose nanocrystals (CNCs) by a chemical-mechanical method. First, bamboo fibers were pre-treated (removal of lignin and hemicellulose) to obtain cellulose. Next, the cellulose was hydrolyzed with sulfuric acid using ultrasonication to obtain CNCs. The diameters of CNCs are in the range of 11-375 nm. The CNCs from DSM showed the highest yield and crystallinity, which was chosen in the film fabrication. The plasticized cassava starch-based films with various amounts (0-0.6 g) of CNCs (from DSM) were prepared and characterized. As the number of CNCs in cassava starch-based films increased, water solubility and the water vapor permeability of CNCs decreased. In addition, the atomic force microscope of the nanocomposite films showed that CNC particles were dispersed uniformly on the surface of cassava starch-based film at 0.2 and 0.4 g content. However, the number of CNCs at 0.6 g resulted in more CNC agglomeration in cassava starch-based films. The 0.4 g CNC in cassava starch-based film was found to have the highest tensile strength (4.2 MPa). Cassava starch-incorporated CNCs from bamboo film can be applied as a biodegradable packaging material.
RESUMO
The effect of argon (Ar) and oxygen (O2) gases as well as the treatment times on the properties of modified bamboo fibers using dielectric barrier discharge (DBD) plasma at generated power of 180 W were investigated. The plasma treatment of bamboo fibers with inert gases leads to the generation of ions and radicals on the fiber surface. Fourier transform-infrared spectroscopy (FTIR) confirmed that the functional groups of lignin and hemicellulose were reduced owing to the removal of the amorphous portion of the fibers by plasma etching. X-ray diffraction analysis (XRD) results in an increased crystallinity percentage. X-ray photoelectron spectroscopy (XPS) results showed the oxygen/carbon (O/C) atomic concentration ratio increased with increasing treatment time. The fiber weight loss percentage increased with increased treatment time. Scanning electron microscopy (SEM) images showed that partial etching of the fiber surface led to a higher surface roughness and area and that the Ar + O2 gas plasma treatment provided more surface etching than the Ar gas treatment because of the oxidation reaction of the O2 plasma. The mechanical properties of fiber-reinforced epoxy (FRE) matrix composites revealed that the F(tr)RE-Ar (30) samples showed a high tensile strength, whereas the mechanical properties of the F(tr)RE-Ar + O2 sample decreased with increased treatment time.
RESUMO
With the growing interest in environmentally friendly and personalized medicines, new concept for combining three-dimensional printing (3DP) with natural-based biomaterials derived from agro-food wastes has emerged. This approach provides sustainable solutions for agricultural waste management and potential for developing of novel pharmaceutical products with tunable characteristics. This work demonstrated the feasibility of fabricating personalized theophylline films with four different structures (Full, Grid, Star, and Hilbert) using syringe extrusion 3DP and carboxymethyl cellulose (CMC) derived from durian rind wastes. Our findings suggested that all the CMC-based inks with shear thinning properties capable of being extruded smoothly through a small nozzle could potentially be used to fabricate the films with various complex printing patterns and high structural fidelity. The results also demonstrated that the film characteristics and release profiles could be easily modified by simply changing the slicing parameters (e.g., infill density and printing pattern). Amongst all formulations, Grid film, which was 3D-printed with 40 % infill and a grid pattern, demonstrated a highly porous structure with high total pore volume. The voids between printing layers in Grid film increased theophylline release (up to 90 % in 45 min) through improved wetting and water penetration. All findings in this study provide significant insight into how to modify film characteristics simply by digitally changing the printing pattern in slicer software without creating a new CAD model. This approach could help to simplify the 3DP process so that non-specialist users can easily implement it in community pharmacies or hospital on demand.
Assuntos
Bombacaceae , Carboximetilcelulose Sódica , Tinta , Teofilina , Impressão TridimensionalRESUMO
The pulsed electric field (PEF) was applied to improve the extraction yield and properties of rice bran proteins from two rice varieties ("Kum Chao Mor Chor 107" and "Kum Doi Saket"). As compared to the conventional alkaline extraction, PEF treatment at 2.3 kV for 25 min increased the protein extraction efficiency by 20.71-22.8% (p < 0.05). The molecular weight distribution detected by SDS-PAGE and amino acid profiles of extracted rice bran proteins was likely unchanged. The PEF treatment influenced changes in the secondary structures of rice bran proteins, especially from the ß-turn to the ß-sheet structure. Functional properties of rice bran protein including oil holding capacity and emulsifying properties were significantly improved by PEF treatments by about 20.29-22.64% and 3.3-12.0% (p < 0.05), respectively. Foaming ability and foam stability increased by 1.8- to 2.9-fold. Moreover, the in vitro digestibility of protein was also enhanced, which was consistent with the increment of DPPH and ABTS radical-scavenging activities of peptides generated under in vitro gastrointestinal digestion (37.84-40.45% and 28.46-37.86%, respectively). In conclusion, the PEF process could be a novel technique for assisting the extraction and modification of the protein's digestibility and functional properties.
RESUMO
This study investigated the effect of chitosan particle sizes on the properties of carboxymethyl chitosan (CMCh) powders and films. Chitosan powders with different particle sizes (75, 125, 250, 450 and 850 µm) were used to synthesize the CMCh powders. The yield, degree of substitution (DS), and water solubility of the CMCh powders were then determined. The CMCh films prepared with CMCh based on chitosan with different particle sizes were fabricated by a solution casting technique. The water solubility, mechanical properties, and water vapor transmission rate (WVTR) of the CMCh films were measured. As the chitosan particle size decreased, the yield, DS, and water solubility of the synthesized CMCh powders increased. The increase in water solubility was due to an increase in the polarity of the CMCh powder, from a higher conversion of chitosan into CMCh. In addition, the higher conversion of chitosan was also related to a higher surface area in the substitution reaction provided by chitosan powder with a smaller particle size. As the particle size of chitosan decreased, the tensile strength, elongation at break, and WVTR of the CMCh films increased. This study demonstrated that a greater improvement in water solubility of the CMCh powders and films can be achieved by using chitosan powder with a smaller size.