RESUMO
Hexagonal boron nitride (hBN) is an emerging two-dimensional material attracting considerable attention in the industrial sector given its innovative physicochemical properties. Potential risks are associated mainly with occupational exposure where inhalation and skin contact are the most relevant exposure routes for workers. Here we aimed at characterizing the effects induced by composites of thermoplastic polyurethane (TPU) and hBN, using immortalized HaCaT skin keratinocytes and BEAS-2B bronchial epithelial cells. The composite was abraded using a Taber® rotary abraser and abraded TPU and TPU-hBN were also subjected to photo-Fenton-mediated degradation mimicking potential weathering across the product life cycle. Cells were exposed to the materials for 24 h (acute exposure) or twice per week for 4 weeks (chronic exposure) and evaluated with respect to material internalization, cytotoxicity, and proinflammatory cytokine secretion. Additionally, comprehensive mass spectrometry-based proteomics and metabolomics (secretomics) analyses were performed. Overall, despite evidence of cellular uptake of the material, no significant cellular and/or protein expression profiles alterations were observed after acute or chronic exposure of HaCaT or BEAS-2B cells, identifying only few pro-inflammatory proteins. Similar results were obtained for the degraded materials. These results support the determination of hazard profiles associated with cutaneous and pulmonary hBN-reinforced polymer composites exposure.
Assuntos
Compostos de Boro , Poliuretanos , Humanos , Poliuretanos/toxicidade , Poliuretanos/química , Compostos de Boro/química , Compostos de Boro/toxicidade , Linhagem Celular , Pele/efeitos dos fármacos , Pele/metabolismo , Pulmão/efeitos dos fármacos , Pulmão/metabolismo , Queratinócitos/efeitos dos fármacos , Queratinócitos/metabolismo , Citocinas/metabolismo , Sobrevivência Celular/efeitos dos fármacosRESUMO
Lithium-sulfur battery of practical interest requires thin-layer support to achieve acceptable volumetric energy density. However, the typical aluminum current collector of Li-ion battery cannot be efficiently used in the Li/S system due to the insulating nature of sulfur and a reaction mechanism involving electrodeposition of dissolved polysulfides. We study the electrochemical behavior of a Li/S battery using a carbon-coated Al current collector in which the low thickness, the high electronic conductivity, and, at the same time, the host ability for the reaction products are allowed by a binder-free few-layer graphene (FLG) substrate. The FLG enables a sulfur electrode having a thickness below 100 µm, fast kinetics, low impedance, and an initial capacity of 1000 mAh gS -1 with over 70% retention after 300 cycles. The Li/S cell using FLG shows volumetric and gravimetric energy densities of 300 Wh L-1 and 500 Wh kg-1, respectively, which are values well competing with commercially available Li-ion batteries.
RESUMO
The printing of three-dimensional (3D) porous electrodes for Li-ion batteries is considered a key driver for the design and realization of advanced energy storage systems. While different 3D printing techniques offer great potential to design and develop 3D architectures, several factors need to be addressed to print 3D electrodes, maintaining an optimal trade-off between electrochemical and mechanical performances. Herein, we report the first demonstration of 3D printed Si-based electrodes fabricated using a simple and cost-effective fused deposition modelling (FDM) method, and implemented as anodes in Li-ion batteries. To fulfil the printability requirement while maximizing the electrochemical performance, the composition of the FDM filament has been engineered using polylactic acid as the host polymeric matrix, a mixture of carbon black-doped polypyrrole and wet-jet milling exfoliated few-layer graphene flakes as conductive additives, and Si nanoparticles as the active material. The creation of a continuous conductive network and the control of the structural properties at the nanoscale enabled the design and realization of flexible 3D printed anodes, reaching a specific capacity up to â¼345 mA h g-1 at the current density of 20 mA g-1, together with a capacity retention of 96% after 350 cycles. The obtained results are promising for the fabrication of flexible polymeric-based 3D energy storage devices to meet the challenges ahead for the design of next-generation electronic devices.
RESUMO
One of the applications of graphene in which its scalable production is of utmost importance is the development of polymer composites. Among the techniques used to produce graphene flakes, the liquid-phase exfoliation (LPE) of graphite stands out due to its versatility and scalability. However, solvents suitable for the LPE process are generally toxic and have a high boiling point, making the processing challenging. The use of low boiling point solvents could be convenient for the processing, due to the easiness of their removal. In this study, the use of poly(methyl methacrylate) (PMMA) as a stabilizing agent is proposed for the production of graphene flakes in a low boiling point solvent, that is, acetone. The graphene dispersions produced in the mixture acetone-PMMA have higher concentration, +175 %, and contain a higher percentage of few-layer graphene flakes (<5â layers), that is, +60 %, compared to the dispersions prepared in acetone. The as-produced graphene dispersions are used to develop graphene/acrylonitrile-butadiene-styrene composites. The mechanical properties of the pristine polymer are improved, that is, +22 % in the Young's modulus, by adding 0.01â wt. % of graphene flakes. Moreover, a decrease of ≈20 % in the oxygen permeability is obtained by using 0.1â wt. % of graphene flakes filler, compared to the unloaded matrix.
RESUMO
OBJECTIVES: The study aims at demonstrating the feasibility of a novel type of coupling-agent-free resin composite based on nano-porous fillers. METHODS: The fillers were obtained by ball-milling anodic alumina membranes. Composites were prepared with standard resin at maximum loading of 50% by weight. The resin matrix penetration into the pores was verified visually by scanning electron microscopy and mechanically by atomic force microscopy in force modulation mode. The dynamic flexural modulus at 1Hz was measured by dynamic mechanical analysis. Silver nanoparticles were also synthesized in the pores and their release was investigated with inductive coupled plasma optical emission spectrometry. RESULTS: A storage modulus of 5GPa was measured, similar to the â¼6GPa ones of two coupling-agent-based dental restorative composites used for comparison, which is a promising starting point, additionally showing better one-year equivalent ageing as compared to both commercial materials. Loading the pores with silver nanoparticles was demonstrated as well as their subsequent release in a model system. SIGNIFICANCE: The alumina micro-particles with interconnected nano-pores allow mechanical interlocking between fillers and matrix without the need for chemical bonding. This material is also promising for being made bio-active, after pore filling with different agents.