Wet-chemical synthesis and consolidation of stoichiometric bismuth telluride nanoparticles for improving the thermoelectric figure-of-merit.

Bismuth telluride nanoparticles (NPs) have been synthesized using a low-temperature wet-chemical approach from bismuth(III) oleate and tri-n-octylphosphine telluride. The size and shape of the NPs can be controlled by adjusting the temperature, reaction time, and nature of the surfactants and solvents. Aromatic hydrocarbons (toluene, xylenes) and ethers (phenyl- and benzyl-ether) favor the formation of stoichiometric Bi2Te3 NPs of platelike morphology, whereas the presence of oleylamine and 1-dodecanethiol yields Bi-rich Bi2Te3 spherical NPs. XRD, IR, SEM, TEM, and SAED techniques have been used to characterize the obtained products. We show that the surfactants can be efficiently removed from the surface of the NPs using a two-step process employing nitrosonium tetrafluoroborate and hydrazine hydrate. The surfactant-free NPs were further consolidated into high density pellets using cold-pressing and field-assisted sintering techniques. The sintered surfactant-free Bi2Te3 showed electrical and thermal properties comparable to Bi2Te3 materials processed through conventional solid state techniques, and greatly improved over other nanostructured Bi2Te3 materials synthesized by wet-chemical approaches.

Enhanced thermoelectric figure of merit of p-type half-Heuslers.

Half-Heuslers would be important thermoelectric materials due to their high temperature stability and abundance if their dimensionless thermoelectric figure of merit (ZT) could be made high enough. The highest peak ZT of a p-type half-Heusler has been so far reported about 0.5 due to the high thermal conductivity. Through a nanocomposite approach using ball milling and hot pressing, we have achieved a peak ZT of 0.8 at 700 °C, which is about 60% higher than the best reported 0.5 and might be good enough for consideration for waste heat recovery in car exhaust systems. The improvement comes from a simultaneous increase in Seebeck coefficient and a significant decrease in thermal conductivity due to nanostructures. The samples were made by first forming alloyed ingots using arc melting and then creating nanopowders by ball milling the ingots and finally obtaining dense bulk by hot pressing. Further improvement in ZT is expected when average grain sizes are made smaller than 100 nm.

Glassy thermal conductivity in the two-phase Cu(x)Ag(3-x)SbSeTe(2) alloy and high temperature thermoelectric behavior.

We have measured the thermal transport properties over the temperature range 1.8 K

Statistical Analysis of a Round-Robin Measurement Survey of Two Candidate Materials for a Seebeck Coefficient Standard Reference Material.

In an effort to develop a Standard Reference Material (SRM™) for Seebeck coefficient, we have conducted a round-robin measurement survey of two candidate materials-undoped Bi2Te3 and Constantan (55 % Cu and 45 % Ni alloy). Measurements were performed in two rounds by twelve laboratories involved in active thermoelectric research using a number of different commercial and custom-built measurement systems and techniques. In this paper we report the detailed statistical analyses on the interlaboratory measurement results and the statistical methodology for analysis of irregularly sampled measurement curves in the interlaboratory study setting. Based on these results, we have selected Bi2Te3 as the prototype standard material. Once available, this SRM will be useful for future interlaboratory data comparison and instrument calibrations.

Synthesis and thermoelectric power of nitrogen-doped carbon nanotubes.

We have previously shown that high-purity multiwalled carbon nanotubes (pristine MWNTs) can be prepared from a mixture of xylene-ferrocene (99 at% C:1 at% Fe) inside a quartz tube reactor operating at approximately 700 degrees C. In a similar process, approximately 3 g of melamine (C3H6N6) was introduced during the growth of MWNTs to prepare nitrogen-doped nanotubes. The structural and electronic properties of nitrogen-doped MWNTs were determined by scanning electron microscopy, high-resolution transmission electron microscopy (HRTEM), electron energy loss spectroscopy (EELS), and thermopower measurements. The individual nitrogen-doped nanotube exhibits a bamboo-like structure and comprises 6-16 tube walls, as evidenced by HRTEM studies. The EELS measurements yielded an average nitrogen content of approximately 5 at% in the doped tubes. The thermoelectric power data of nitrogen-doped MWNTs remained negative even after exposure to oxygen for an extended period of time, suggesting that nitrogen doping of MWNTs renders them n-type, consistent with scanning tunneling spectroscopic studies on similar nanotubes.