Sodium Manganese Ferrite Water Splitting Cycle: Unravelling the Effect of Solid-Liquid Interfaces in Molten Alkali Carbonates.

In this work, the Na2CO3 of the sodium manganese ferrite thermochemical cycle was substituted by different eutectic or eutectoid alkali carbonate mixtures. Substituting Na2CO3 with the eutectoid (Li0.07Na0.93)2CO3 mixture resulted in faster hydrogen production after the first cycle, shifting the hydrogen production maximum toward shorter reaction times. Thermodynamic calculations and in situ optical microscopy attributed this fact to the partial melting of the eutectoid carbonate, which helps the diffusion of the ions. Unfortunately, all the mixtures exhibit a significant loss of reversibility in terms of hydrogen production upon cycling. Among them, the nonsubstituted Na mixture exhibits the highest reversibility in terms of hydrogen production followed by the 7%Li-Na mixture, while the 50%Li-Na and Li-K-Na mixtures do not produce any hydrogen after the first cycle. The loss of reversibility is attributed to both the formation of undesired phases and sintering, the latter being more pronounced in the eutectic and eutectoid alkali carbonate mixtures, where the melting of the carbonate is predicted by thermodynamics.

Thermal and Photocatalytic Performance of Unsaturated Polyester Resins Modified with TiO2 Nanoparticles as Panel Bodies for Vehicles.

The transport sector is the fastest growing contributor to climate emissions and experiences the highest growth in energy use. This study explores the use of TiO2 nanoparticles for obtaining photocatalytic nanocomposites with improved infrared reflectance properties. The nanocomposites were prepared by dispersing 0-20 wt% of TiO2 nanoparticles in an unsaturated polyester resin. The effect of TiO2 on the curing kinetics was studied by differential scanning calorimetry, showing a significant delay of the curing reactions. The thermal reflectance of the modified resins was characterized by UV-Vis-NIR spectrophotometry, measuring total solar reflectance (TSR). The TiO2 greatly increased the TSR of the resin, due to the reflectance properties of the nanoparticles and the change in color of the modified resin. These nanocomposites reflect a significant part of near-infrared radiation, which can contribute to a reduction of the use of heating, ventilation, and air conditioning. Moreover, the photocatalytic effect of the TiO2 modified nanocomposites was studied by monitoring the degradation of an organic model contaminant in an aqueous medium under UV light, and the reusability of the nanocomposites was studied with 5 cycles. The developed nanocomposites are proposed as a solution for reducing global warming and pollutant emissions.

Direct Powder Extrusion of Paracetamol Loaded Mixtures for 3D Printed Pharmaceutics for Personalized Medicine via Low Temperature Thermal Processing.

Three-dimensional printed drug development is nowadays an active area in the pharmaceutical industry, where the search for an appropriate edible carrier that permits the thermal processing of the mixture at temperature levels that are safe for the drug is an important field of study. Here, potato starch and hydroxypropyl cellulose based mixtures loaded with paracetamol up to 50% in weight were processed by hot melt extrusion at 85 °C to test their suitability to be thermally processed. The extruded mixtures were tested by liquid chromatography to analyze their release curves and were thermally characterized. The drug recovery was observed to be highly dependent on the initial moisture level of the mixture, the samples being prepared with an addition of water at a ratio of 3% in weight proportional to the starch amount, highly soluble and easy to extrude. The release curves showed a slow and steady drug liberation compared to a commercially available paracetamol tablet, reaching the 100% of recovery at 60 min. The samples aged for 6 weeks showed slower drug release curves compared to fresh samples, this effect being attributable to the loss of moisture. The paracetamol loaded mixture in powder form was used to print pills with different sizes and geometries in a fused deposition modelling three-dimensional printer modified with a commercially available powder extrusion head, showing the potential of this formulation for use in personalized medicine.

Colloidal stability and ecotoxicity of multiwalled carbon nanotubes: Influence of select organic matters.

In the last few years, the release of multiwalled carbon nanotubes (MWCNTs) into the environment has raised serious concerns regarding their fate and potential impacts. Aquatic organisms constitute an important pathway for their entrance and transfer throughout the food web, and the current demand for standardization of methodologies to analyze the interactions of MWCNTs with them requires aquatic media that represent natural systems. However, the inherent hydrophobicity of MWCNTs and the substances present in natural waters may greatly affect their stability and bioavailability. The present study analyzes the influence of the most referenced synthetic and natural organic matters (Sigma-Aldrich humic acid and Suwannee River natural organic matter) in the agglomeration kinetics and ecotoxicity of MWCNTs, with the aim of determining their suitability to fulfill the current standardization requirements. Natural organic matter provides increased colloidal stability to the MWCNTs' dispersions, which results in higher adverse effects on the key invertebrate organism Daphnia magna. Furthermore, the results obtained with this type of organic matter allow for observation of the important role of the outer diameter and content impurities of MWCNTs in their stability and ecotoxicity on daphnids. Sigma-Aldrich humic acid appeared to alter the response of the organisms to carbon nanotubes compared with that observed in the presence of natural organic matter.