Assessment of static and perfusion methods for decellularization of PCL membrane-supported periodontal ligament cell sheet constructs.

OBJECTIVES: Decellularization aims to harness the regenerative properties of native extracellular matrix. The objective of this study was to evaluate different methods of decellularization of periodontal ligament cell sheets whilst maintaining their structural and biological integrity. DESIGN: Human periodontal ligament cell sheets were placed onto melt electrospun polycaprolactone (PCL) membranes that reinforced the cell sheets during the various decellularization protocols. These cell sheet constructs (CSCs) were decellularized under static/perfusion conditions using a) 20 mM ammonium hydroxide (NH4OH)/Triton X-100, 0.5% v/v; and b) sodium dodecyl sulfate (SDS, 0.2% v/v), both +/- DNase besides Freeze-thaw (F/T) cycling method. CSCs were assessed using a collagen quantification assay, immunostaining and scanning electron microscopy. Residual fibroblast growth factor (bFGF), vascular endothelial growth factor (VEGF) and hepatocyte growth factor (HGF) were assessed with Bio-plex assays. RESULTS: DNA removal without DNase was higher under static conditions. However, after DNase treatment, there were no differences between the different decellularization methods with virtually 100% DNA removal. DNA elimination in F/T was less efficient even after DNase treatment. Collagen content was preserved with all techniques, except with SDS treatment. Structural integrity was preserved after NH4OH/Triton X-100 and F/T treatment, while SDS altered the extracellular matrix structure. Growth factor amounts were reduced after decellularization with all methods, with the greatest reduction (to virtually undetectable amounts) following SDS treatment, while NH4OH/Triton X-100 and DNase treatment resulted in approximately 10% retention. CONCLUSIONS: This study showed that treatment with NH4OH/Triton X-100 and DNase solution was the most efficient method for DNA removal and the preservation of extracellular matrix integrity and growth factors retention.

Oleic acid surfactant in polycaprolactone/hydroxyapatite-composites for bone tissue engineering.

Bone substitutes are required to repair osseous defects caused by a number of factors, such as traumas, degenerative diseases, and cancer. Autologous bone grafting is typically used to bridge bone defects, but suffers from chronic pain at the donor-site and limited availability of graft material. Tissue engineering approaches are being investigated as viable alternatives, which ideal scaffold should be biocompatible, biodegradable, and promote cellular interactions and tissue development, need to present proper mechanical and physical properties. In this study, poly(ε-caprolactone) (PCL), oleic acid (OA) and hydroxyapatite (HAp) were used to obtain films whose properties were investigated by contact angle, scanning electron microscopy, atomic force microscopy, tensile mechanical tests, and in vitro tests with U2OS human osteosarcoma cells by direct contact. Our results indicate that by using OA as surfactant/dispersant, it was possible to obtain a homogenous film with HAp. The PCL/OA/Hap sample had twice the roughness of the control (PCL) and a lower contact angle, indicating increased hydrophilicity of the film. Furthermore, mechanical testing showed that the addition of HAp decreased the load at yield point and tensile strength and increased tensile modulus, indicating a more brittle composition vs. PCL matrix. Preliminary cell culture experiments carried out with the films demonstrated that U2OS cells adhered and proliferated on all surfaces. The data demonstrate the improved dispersion of HAp using OA and the important consequences of this addition on the composite, unveiling the potentially of this composition for bone growth support. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1076-1082, 2016.

Nutrient diffusion and simple nth-order consumption in regenerative tissue and biocatalytic sensors.

This contribution addresses intra-tissue molar density profiles for nutrients, oxygen, growth factors, and other essential ingredients that anchorage-dependent cells require for successful proliferation on biocompatible surfaces. One-dimensional transient and steady state models of the reaction-diffusion equation are solved to correct a few deficiencies in the first illustrative example of diffusion and zeroth-order rates of consumption in tissues with rectangular geometry, as discussed in Ref. [(Griffith and Swartz, 2006) 1]. The functional form of the molar density profile for each species depends on geometry and the magnitude of the species-specific intra-tissue Damköhler number. The tissue's central core is reactant starved at high consumption rates and low rates of intra-tissue diffusion when the Damköhler number exceeds its geometry-sensitive critical value. Ideal tissue engineering designs avoid the diffusion-limited regime such that attached cells are exposed to all of the ingredients required for proliferation everywhere within a regenerative matrix. Analytical and numerical molar density profiles that satisfy the unsteady state modified diffusion equation with pseudo-homogeneous n(th)-order rates of intra-tissue consumption (i.e., n=0,1,2) allow one to (i) predict von Kármán-Pohlhausen mass transfer boundary layer thicknesses, measured inward from the external biomaterial surface toward its central core, and, most importantly, (ii) estimate the time required to achieve steady state conditions for regenerative tissue growth and biocatalytic sensing.