Tin Oxide Nanoparticles via Solar Vapor Deposition for Hexavalent Chromium Remediation.

Tin oxide nanoparticles optimized to capture low concentrations of hexavalent chromium from water were developed through a facile, scalable, and low-cost one-step solar vapor deposition methodology. Considering the preservation of high electron donation capacity as the key to support the reduction of mobile Cr(VI) into insoluble forms, the growth of SnO nanoparticles was favored by the co-evaporation of SnO2 with Fe powders at various mass ratios. Characterization techniques indicated that the percentage and the stability of SnO is proportional to the Fe content in the target with a requirement of at least 50% wt to inhibit the formation of a passive SnO2 surface layer. The produced particles were evaluated regarding their efficiency to capture Cr(VI) under conditions similar to water treatment for drinking purposes (pH 7). It was revealed that passivation-free SnO nanoparticles deliver significant improvement in the adsorption capacity corresponding to the residual concentration of 25 µg/L, reaching a value of 1.74 mg/g for the sample prepared with 50% wt Fe in the target. The increase of water acidity was found responsible for the activation of more reduction sites on the particle surface, as reflected through the elevation of efficiency by more than 20% at pH 6.

Enhanced detoxification of Cr6+ by Shewanella oneidensis via adsorption on spherical and flower-like manganese ferrite nanostructures.

Maximizing the safe removal of hexavalent chromium (Cr6+) from waste streams is an increasing demand due to the environmental, economic and health benefits. The integrated adsorption and bio-reduction method can be applied for the elimination of the highly toxic Cr6+ and its detoxification. This work describes a synthetic method for achieving the best chemical composition of spherical and flower-like manganese ferrite (MnxFe3-xO4) nanostructures (NS) for Cr6+ adsorption. We selected NS with the highest adsorption performance to study its efficiency in the extracellular reduction of Cr6+ into a trivalent state (Cr3+) by Shewanella oneidensis (S. oneidensis) MR-1. MnxFe3-xO4 NS were prepared by a polyol solvothermal synthesis process. They were characterised by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), dynamic light scattering (DLS) and Fourier transform-infrared (FTIR) spectroscopy. The elemental composition of MnxFe3-xO4 was evaluated by inductively coupled plasma atomic emission spectroscopy. Our results reveal that the oxidation state of the manganese precursor significantly affects the Cr6+ adsorption efficiency of MnxFe3-xO4 NS. The best adsorption capacity for Cr6+ is 16.8 ± 1.6 mg Cr6+/g by the spherical Mn0.22+Fe2.83+O4 nanoparticles at pH 7, which is 1.4 times higher than that of Mn0.8Fe2.2O4 nanoflowers. This was attributed to the relative excess of divalent manganese in Mn0.22+Fe2.83+O4 based on our XPS analysis. The lethal concentration of Cr6+ for S. oneidensis MR-1 was 60 mg L-1 (determined by flow cytometry). The addition of Mn0.22+Fe2.83+O4 nanoparticles to S. oneidensis MR-1 enhanced the bio-reduction of Cr6+ 2.66 times compared to the presence of the bacteria alone. This work provides a cost-effective method for the removal of Cr6+ with a minimum amount of sludge production.

Correction: Enhanced detoxification of Cr6+ by Shewanella oneidensis via adsorption on spherical and flower-like manganese ferrite nanostructures.

[This corrects the article DOI: 10.1039/D2NA00691J.].

Oxygen Evolution Reaction at IrO2/Ir(Ni) Film Electrodes Prepared by Galvanic Replacement and Anodization: Effect of Precursor Ni Film Thickness.

IrO2/Ir(Ni) film electrodes of variable Ni content have been prepared via a galvanic replacement method, whereby surface layers of pre-deposited Ni are replaced by Ir, followed by electrochemical anodization. Electrodeposition of Ni on a glassy carbon electrode support has been carried out at constant potential and the charge of electrodeposited Ni controlled so as to investigate the effect of precursor Ni layer thickness on the electrocatalytic activity of the corresponding IrO2/Ir(Ni)/GC electrodes for the oxygen evolution reaction (OER). After their preparation, these electrodes were characterized by microscopic (SEM) and spectroscopic (EDS, XPS) techniques, revealing the formation of Ir deposits on the Ni support and a thin IrO2 layer on their surfaces. To determine the electroactive surface area of the IrO2 coatings, cyclic voltammograms were recorded in the potential range between hydrogen and oxygen evolution and the charge under the anodic part of the curves, corresponding to Ir surface oxide formation, served as an indicator of the quantity of active IrO2 in the film. The electrocatalytic activity of the coatings for OER was investigated by current-potential curves under steady state conditions, revealing that the catalysts prepared from thinner Ni films exhibited enhanced electrocatalytic performance.

Octadecylamine-Mediated Versatile Coating of CoFe2O4 NPs for the Sustained Release of Anti-Inflammatory Drug Naproxen and in Vivo Target Selectivity.

Magnetic nanoparticles (MNPs) can play a distinct role in magnetic drug delivery via their distribution to the targeted area. The preparation of such MNPs is a challenging multiplex task that requires the optimization of size, magnetic, and surface properties for the achievement of desirable target selectivity, along with the sustained drug release as a prerequisite. In that context, CoFe2O4 MNPs with a small size of ∼7 nm and moderate saturation magnetization of ∼60 emu g(-1) were solvothermally synthesized in the presence of octadecylamine (ODA) with a view to investigate the functionalization route effect on the drug release. Synthetic regulations allowed us to prepare MNPs with aminated (AmMNPs) and amine-free (FAmMNPs) surface. The addition of the nonsteroidal anti-inflammatory drug with a carboxylate donor, Naproxen (NAP), was achieved by direct coupling with the NH2 groups, rendered by ODA, through the formation of an amide bond in the case of AmMNPs. In the case of FAmMNPs, indirect coupling of NAP was performed through an intermediate linker (polyethylenimine) and on PEG-ylated MNPs. FT-IR, (1)H NMR, (13)C NMR, and UV-vis data confirmed the addition of NAP, whereas diverse drug-release behavior was observed for the different functionalization approaches. The biological behavior of the MNPs@NAP was evaluated in vitro in rat serum and in vivo in mice, after radiolabeling with a γ-emitting radionuclide, (99m)Tc. The in vivo fate of MNPs@NAP carriers was in straightforward relation with the direct or indirect coupling of NAP. Furthermore, an inflammation was induced intramuscularly, where the directly coupled (99m)Tc-MNPs@NAP carriers showed increased accumulation at the inflammation site.

ZnO-based thin film transistors employing aluminum titanate gate dielectrics deposited by spray pyrolysis at ambient air.

The replacement of SiO2 gate dielectrics with metal oxides of higher dielectric constant has led to the investigation of a wide range of materials with superior properties compared with SiO2. Despite their attractive properties, these high-k dielectrics are usually manufactured using costly vacuum-based techniques. To overcome this bottleneck, research has focused on the development of alternative deposition methods based on solution-processable metal oxides. Here we report the application of spray pyrolysis for the deposition and investigation of Al2x-1·TixOy dielectrics as a function of the [Ti(4+)]/[Ti(4+)+2·Al(3+)] ratio and their implementation in thin film transistors (TFTs) employing spray-coated ZnO as the active semiconducting channels. The films are studied by UV-visible absorption spectroscopy, spectroscopic ellipsometry, impedance spectroscopy, atomic force microscopy, X-ray diffraction and field-effect measurements. Analyses reveal amorphous Al2x-1·TixOy dielectrics that exhibit a wide band gap (∼4.5 eV), low roughness (∼0.9 nm), high dielectric constant (k ∼ 13), Schottky pinning factor S of ∼0.44 and very low leakage currents (<5 nA/cm(2)). TFTs employing stoichiometric Al2O3·TiO2 gate dielectrics and ZnO semiconducting channels exhibit excellent electron transport characteristics with low operating voltages (∼10 V), negligible hysteresis, high on/off current modulation ratio of ∼10(6), subthreshold swing (SS) of ∼550 mV/dec and electron mobility of ∼10 cm(2) V(-1) s(-1).

Factors controlling the enhanced mechanical and thermal properties of nanodiamond-reinforced cross-linked high density polyethylene.

A systematic investigation of the factors influencing the notable enhancement of the mechanical and thermal properties of nanodiamonds (NDs)-reinforced cross-linked high density polyethylene (PEX) is presented in this work. The effects of crystal structure and molecular conformation as well as filler dispersion and adhesion with the matrix were found to govern the mechanical properties of the final composites. A considerable increase in the strength, toughness, and elastic modulus of the materials was found for the composites with filler content below 1 wt %. For higher NDs concentrations, the properties degraded. When filler concentration does not exceed 1 wt %, enhanced adhesion with the matrix is achieved, allowing a more successful load transfer between the filler and the matrix, thus enabling an effective reinforcement of the composites. The higher degree of crystallinity along with larger crystal size are also positively influencing the mechanical properties of PEX. Higher filler concentrations, on the other hand, lead to the formation of larger aggregates, which lead to lower adhesion with the matrix, while they also constitute stress concentrators and therefore reduce the positive reinforcement of the matrix. The thermal conductivity of the composites was also found to be significantly increased for low-filler concentrations. This enhancement was less significant for higher NDs concentrations. It is concluded that this reinforcement is due to the heat capacity increase that NDs incorporation causes in PEX. Additionally, a thermal stability enhancement was found for the composite with minimum filler content.