RESUMO
Organic light-emitting diodes (OLEDs) that are able to emit high levels of circularly polarized (CP) light hold significant promise in numerous future technologies. Such devices require chiral emissive materials to enable CP electroluminescence. However, the vast majority of current OLED emitter classes, including the state-of-the-art triplet-harvesting thermally activated delayed fluorescence (TADF) materials, produce very low levels of CP electroluminescence. Here a host-guest strategy that allows for energy transfer between a chiral polymer host and a representative chiral TADF emitter is showcased. Such a mechanism results in a large amplification of the circular polarization of the emitter. As such, this study presents a promising avenue to further boost the performance of circularly polarized organic light-emitting diode devices, enabling their further development and eventual commercialization.
RESUMO
Circular dichroism spectroscopy is a key probe of the structural and optical properties of chiral materials, however, commercial circular dichroism spectrometers are large, prohibitively expensive and rarely offer environmental control of the sample under test. Using Fresnel rhombs as inexpensive broadband quarter-wave plates, we demonstrate two novel, low-cost (<£2000) and portable imaging systems controlled by our own bespoke open-source control software which are capable of spatially mapping the circular dichroism of chiral solid state films. By coupling these imaging systems with a temperature controlled stage, we show that we can rapidly identify the thermal processing conditions required to maximise circular dichroism in chiral solid state films by measuring circular dichroism in situ during thermal annealing of a sample under test. The accuracy and spatial resolution of these circular dichroism imagers are cross-compared against our previous studies using an existing circular dichroism imaging system at the Diamond Light Source and are shown to be in good agreement, with a sensitivity down to 250 mdeg and a spatial resolution of 100 µm.
RESUMO
Helicity is expressed differently in ortho- and para-fused acenes-helicenes and twistacenes, respectively. While the extent of helicity is constant in helicenes, it can be tuned in twistacenes, and the handedness of flexible twistacenes is often determined by more rigid helicenes. Here, we combine helicenes with rigid twistacenes consisting of a tunable degree of twisting, forming helitwistacenes. While the X-ray structures reveal that the connection does not affect the helicity of each moiety, their electronic circular dichroism (ECD) and circularly polarized luminescence (CPL) spectra are strongly affected by the helicity of the twistacene unit, resulting in solvent-induced sign inversion. ROESYâ NMR and TD-DFT calculations support this observation, which is explained by differences in the relative orientation of the helicene and twistacene moieties.
RESUMO
We synthesized a fluorene-bithiophene co-polymer with chiral side chains (cPFT2) and investigated its chiroptical properties via synchotronradiation circular dichroism. We observed that thin films of the polymer display an intense circular dichroism (CD) upon annealing, which is of opposite handedness to the CD reported for similar polyfluorenes bearing the same enantiomeric chiral side chain. We then contrast the properties of this polymer with chiral side chain fluorene homopolymer (cPF) and observe large differences in their thin film morphology. Using photoluminescence spectroscopy, we uncover evidence of polymer chain bending in cPFT2, which is further supported by theoretical calculations, and propose an explanation for the observed inverted optical activity.
RESUMO
Introduction: Evaluation and management of an early pregnancy diagnosis are clinically pertinent to multiple specialties that will encounter reproductive-age patients. We designed an interactive, small-group, flipped classroom session teaching concepts related to early pregnancy for obstetrics and gynecology clerkship students. Methods: Students received advance preparation materials prior to joining the small group facilitated by clinical educators in the OB/GYN department. Following each 2-hour session, students and facilitators were asked to voluntarily complete a satisfaction survey. Results: Over six clerkships, which occurred across 9 months, 116 students participated. Eighty-three students completed the satisfaction survey, with 98% agreeing that the session was helpful in applying learned principles to patient care. A very high rate of students (average: 93%) self-reported that they achieved the session's learning objectives after completing the prework and interactive small-group teaching. Eleven clinical instructors completed the survey, with 91% agreeing that they were able to facilitate active learning using the materials and 82% agreeing that the curriculum reduced their personal preparation time to teach compared to traditional didactics. Discussion: This interactive flipped classroom session achieves specified learning objectives and helps students apply learned concepts in the evaluation of early pregnancy while standardizing clerkship education and reducing the burden on clinical educators.
Assuntos
Estágio Clínico , Ginecologia , Obstetrícia , Estudantes de Medicina , Feminino , Gravidez , Humanos , Ginecologia/educação , Obstetrícia/educação , CurrículoRESUMO
[This corrects the article DOI: 10.1039/D2TC01224C.].
RESUMO
Chiral π-conjugated molecules bring new functionality to technological applications and represent an exciting, rapidly expanding area of research. Their functional properties, such as the absorption and emission of circularly polarized light or the transport of spin-polarized electrons, are highly anisotropic. As a result, the orientation of chiral molecules critically determines the functionality and efficiency of chiral devices. Here we present a strategy to control the orientation of a small chiral molecule (2,2'-dicyano[6]helicene) by the use of organic and inorganic templating layers. Such templating layers can either force 2,2'-dicyano[6]helicene to adopt a face-on orientation and self-assemble into upright supramolecular columns oriented with their helical axis perpendicular to the substrate, or an edge-on orientation with parallel-lying supramolecular columns. Through such control, we show that low- and high-energy chiroptical responses can be independently 'turned on' or 'turned off'. The templating methodologies described here provide a simple way to engineer orientational control and, by association, anisotropic functional properties of chiral molecular systems for a range of emerging technologies.
Assuntos
Elétrons , AnisotropiaRESUMO
Circularly polarised light will revolutionise emerging technologies, including encrypted light-based communications, quantum computing, bioimaging and multi-channel data processing. In order to make use of these remarkable opportunities, high performance photodetectors that can accurately differentiate between left- and right-handed circularly polarised light are desperately needed. Whilst this potential has resulted in considerable research interest in chiral materials and circularly polarised photodetecting devices, their translation into real-world technologies is limited by non-standardised reporting and testing protocols. This mini-review provides an accessible introduction into the working principles of circularly polarised photodetectors and a comprehensive overview of the performance metrics of state-of-the-art devices. We propose a rigorous device characterisation procedure that will allow for standardised evaluation of novel devices, which we hope will accelerate research and investment in this area.
RESUMO
We study the influence of the physical and chemical structure on the chiroptical response of fluorene-based polymeric systems, namely poly(9,9-dioctylfluorene) (PFO) and the donor-acceptor type copolymer poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT). We reveal the significance of electric-magnetic coupling, at both short (molecular-level) and intermediate (delocalised over multiple polymer chains) length scales, on the magnitude of the dissymmetry. These findings provide a framework for the design of new materials with an enhanced chiroptical response.
RESUMO
The dissymmetric interaction between circularly polarised (CP) light and chiral molecules is central to a range of areas, from spectroscopy and imaging to next-generation photonic devices. However, the selectivity in absorption or emission of left-handed versus right-handed CP light is low for many molecular systems. In this perspective, we assess the magnitude of the measured chiroptical response for a variety of chiral systems, ranging from small molecules to large supramolecular assemblies, and highlight the challenges towards enhancing chiroptical activity. We explain the origins of low CP dissymmetry and showcase recent examples in which molecular design, and the modification of light itself, enable larger responses. Our discussion spans spatial extension of the chiral chromophore, manipulation of transition dipole moments, exploitation of forbidden transitions and creation of macroscopic chiral structures; all of which can increase the dissymmetry. Whilst the specific strategy taken to enhance the dissymmetric interaction will depend on the application of interest, these approaches offer hope for the development and advancement of all research fields that involve interactions of chiral molecules and light.
RESUMO
The search for organic biosignatures on Mars will depend on finding material protected from the destructive ambient radiation. Solar ultraviolet can induce photochemical degradation of organic compounds, but certain clays have been shown to preserve organic material. We examine how the SHERLOC instrument on the upcoming Mars 2020 mission will use deep-ultraviolet (UV) (248.6 nm) Raman and fluorescence spectroscopy to detect a plausible biosignature of adenosine 5'-monophosphate (AMP) adsorbed onto Ca-montmorillonite clay. We found that the spectral signature of AMP is not altered by adsorption in the clay matrix but does change with prolonged exposure to the UV laser over dosages equivalent to 0.2-6 sols of ambient martian UV. For pure AMP, UV exposure leads to breaking of the aromatic adenine unit, but in the presence of clay the degradation is limited to minor alteration with new Raman peaks and increased fluorescence consistent with formation of 2-hydroxyadenosine, while 1 wt % Mg perchlorate increases the rate of degradation. Our results confirm that clays are effective preservers of organic material and should be considered high-value targets, but that pristine biosignatures may be altered within 1 sol of martian UV exposure, with implications for Mars 2020 science operations and sample caching.
Assuntos
Meio Ambiente Extraterreno , Marte , Monofosfato de Adenosina , Percloratos , Espectrometria de Fluorescência , Raios UltravioletaRESUMO
Solubilized fullerene derivatives have revolutionized the development of organic photovoltaic devices, acting as excellent electron acceptors. The addition of solubilizing addends to the fullerene cage results in a large number of isomers, which are generally employed as isomeric mixtures. Moreover, a significant number of these isomers are chiral, which further adds to the isomeric complexity. The opportunities presented by single-isomer, and particularly single-enantiomer, fullerenes in organic electronic materials and devices are poorly understood however. Here, ten pairs of enantiomers are separated from the 19 structural isomers of bis[60]phenyl-C61-butyric acid methyl ester, using them to elucidate important chiroptical relationships and demonstrating their application to a circularly polarized light (CPL)-detecting device. Larger chiroptical responses are found, occurring through the inherent chirality of the fullerene. When used in a single-enantiomer organic field-effect transistor, the potential to discriminate CPL with a fast light response time and with a very high photocurrent dissymmetry factor (gph = 1.27 ± 0.06) is demonstrated. This study thus provides key strategies to design fullerenes with large chiroptical responses for use as chiral components of organic electronic devices. It is anticipated that this data will position chiral fullerenes as an exciting material class for the growing field of chiral electronic technologies.
RESUMO
Strongly dissymmetric circularly polarised (CP) luminescence from small organic molecules could transform a range of technologies, such as display devices. However, highly dissymmetric emission is usually not possible with small organic molecules, which typically give dissymmetric factors of photoluminescence (gPL ) less than 10-2 . Here we describe an almost 103 -fold chiroptical amplification of a π-extended superhelicene when embedded in an achiral conjugated polymer matrix. This combination increases the |gPL | of the superhelicene from approximately 3×10-4 in solution to 0.15 in a blend film in the solid-state. We propose that the amplification arises not simply through a chiral environment effect, but instead due to electrodynamic coupling between the electric and magnetic transition dipoles of the polymer donor and superhelicene acceptor, and subsequent CP Förster resonance energy transfer. We show that this amplification effect holds across several achiral polymer hosts and thus represents a simple and versatile approach to enhance the g-factors of small organic molecules.
RESUMO
Polymer thin films that emit and absorb circularly polarised light have been demonstrated with the promise of achieving important technological advances; from efficient, high-performance displays, to 3D imaging and all-organic spintronic devices. However, the origin of the large chiroptical effects in such films has, until now, remained elusive. We investigate the emergence of such phenomena in achiral polymers blended with a chiral small-molecule additive (1-aza[6]helicene) and intrinsically chiral-sidechain polymers using a combination of spectroscopic methods and structural probes. We show that - under conditions relevant for device fabrication - the large chiroptical effects are caused by magneto-electric coupling (natural optical activity), not structural chirality as previously assumed, and may occur because of local order in a cylinder blue phase-type organisation. This disruptive mechanistic insight into chiral polymer thin films will offer new approaches towards chiroptical materials development after almost three decades of research in this area.
RESUMO
Circularly polarized (CP) electroluminescence has been demonstrated as a strategy to improve the performance of organic light-emitting diode (OLED) displays. CP emission can be generated from both small-molecule and polymer OLEDs (SM-OLEDs and PLEDs), but to date, these devices suffer from low dissymmetry factors (g-factor < 0.1), poor device performance, or a combination of the two. Here, we demonstrate the first CP-PLED employing an inverted device architecture. Through this approach, we demonstrate a highly efficient CP-PLED, with a current efficiency of 16.4 cd/A, a power efficiency of 16.6 lm/W, a maximum luminance of over 28,500 cd/m2, and a high EL dissymmetry (gEL) of 0.57. We find that the handedness of the emitted light is sensitive to the PLED device architecture: the sign of CP-EL from an identically prepared active layer reverses between inverted and conventional devices. The inverted structure affords the first demonstration of CP-PLEDs exhibiting both high efficiency and high dissymmetry-the two figures of merit which, until now, have been difficult to achieve at the same time. We also highlight device architecture and associated internal electric field to be a previously unexplored means to control the handedness of CP emission. Our findings significantly broaden the versatility of CP emissive devices and should enable their further application in a variety of other CP-dependent technologies.
RESUMO
Graphene-coated polypropylene (PP) textile fibers are presented for their use as temperature sensors. These temperature sensors show a negative thermal coefficient of resistance (TCR) in a range between 30 and 45 °C with good sensitivity and reliability and can operate at voltages as low as 1 V. The analysis of the transient response of the temperature on resistance of different types of graphene produced by chemical vapor deposition (CVD) and shear exfoliation of graphite (SEG) shows that trilayer graphene (TLG) grown on copper by CVD displays better sensitivity due to the better thickness uniformity of the film and that carbon paste provides good contact for the measurements. Along with high sensitivity, TLG on PP shows not only the best response but also better transparency, mechanical stability, and washability compared to SEG. Temperature-dependent Raman analysis reveals that the temperature has no significant effect on the peak frequency of PP and expected effect on graphene in the demonstrated temperature range. The presented results demonstrate that these flexible, lightweight temperature sensors based on TLG with a negative TCR can be easily integrated in fabrics.
RESUMO
In the midst of the COVID-19 pandemic, science is crucial to inform public policy. At the same time, mistrust of scientists and misinformation about scientific facts are rampant. Six scientists, actively involved in outreach, reflect on how to build a better understanding and trust of science.
RESUMO
The emission of circularly polarized light is central to many applications, including data storage, optical quantum computation, biosensing, environmental monitoring, and display technologies. An emerging method to induce (chiral) circularly polarized (CP) electroluminescence from the active layer of polymer light-emitting diodes (polymer OLEDs; PLEDs) involves blending achiral polymers with chiral small-molecule additives, where the handedness/sign of the CP light is controlled by the absolute stereochemistry of the small molecule. Through the in-depth study of such a system we report an interesting chiroptical property: the ability to tune the sign of CP light as a function of active layer thickness for a fixed enantiomer of the chiral additive. We demonstrate that it is possible to achieve both efficient (4.0 cd/A) and bright (8000 cd/m2) CP-PLEDs, with high dissymmetry of emission of both left-handed (LH) and right-handed (RH) light, depending on thickness (thin films, 110 nm: gEL = 0.51, thick films, 160 nm: gEL = -1.05, with the terms "thick" and "thin" representing the upper and lower limits of the thickness regime studied), for the same additive enantiomer. We propose that this arises due to an interplay between localized CP emission originating from molecular chirality and CP light amplification or inversion through a chiral medium. We link morphological, spectroscopic, and electronic characterization in thin films and devices with theoretical studies in an effort to determine the factors that underpin these observations. Through the control of active layer thickness and device architecture, this study provides insights into the mechanisms that result in CP luminescence and high performance from CP-PLEDs, as well as demonstrating new opportunities in CP photonic device design.