High-performance activation of ozone by sonocavitation for BTEX degradation in water.

This work presents a novel advanced oxidation process (AOP) for degradation of emerging organic pollutants - benzene, toluene, ethylbenzene and xylenes (BTEXs) in water. A comparative study was performed for sonocavitation assisted ozonation under 40-120 kHz and 80-200 kHz dual frequency ultrasounds (DFUS). Based on the obtained results, the combination of 40-120 kHz i.e., low-frequency US (LFDUS) with O3 exhibited excellent oxidation capacity degrading 99.37-99.69% of BTEXs in 40 min, while 86.09-91.76% of BTEX degradation was achieved after 60 min in 80-200 kHz i.e., high-frequency US (HFDUS) combined with O3. The synergistic indexes determined using degradation rate constants were found as 7.86 and 2.9 for LFDUS/O3 and HFDUS/O3 processes, respectively. The higher extend of BTEX degradation in both processes was observed at pH 6.5 and 10. Among the reactive oxygen species (ROSs), hydroxyl radicals (HO•) were found predominant according to scavenging tests, singlet oxygen also importantly contributed in degradation, while O2•- radicals had a minor contribution. Sulfate (SO42-) ions demonstrated higher inhibitory effect compared to chloride (Cl-) and carbonate (CO32-) ions in both processes. Degradation pathways of BTEX was proposed based on the intermediates identified using GC-MS technique.

A fluorescent NBD "turn-on" probe for the rapid and on-site analysis of fructose in food.

High fructose intake is an important cause of metabolic disease. Due to the increasing prevalence of metabolic diseases worldwide, the development of an accurate and efficient tool for monitoring fructose in food is urgently needed to control the intake of fructose. Herein, a new fluorescent probe NBD-PQ-B with 7-nitrobenz-2-oxa-1, 3-diazole (NBD) as the fluorophore, piperazine (PQ) as the bridging group and phenylboronic acid (B) as the recognition receptor, was synthesized to detect fructose. The fluorescence of NBD-PQ-B increased linearly at 550 nm at an excitation wavelength of 497 nm with increasing fructose concentration from 0.1 to 20 mM. The limit of detection (LOD) of fructose was 40 µM. The pKa values of NBD-PQ-B and its fructose complexes were 4.1 and 10.0, respectively. In addition, NBD-PQ-B bound to fructose in a few seconds. The present technique was applied to determine the fructose content in beverages, honey, and watermelon with satisfactory results. Finally, the system could not only be applied in an aqueous solution with a spectrophotometer, but also be fabricated as a NBD-PQ-B/polyvinyl oxide (PEO) film by electrospinning for on-site food analysis simply with the assistance of a smartphone.

Synthesis of copper/carbon nanofibers by electrostatic spinning toward persulfate activation for treatment of antibiotic wastewater.

Antibiotics in water will cause serious harm to human health and ecosystem. Carbon-based materials and transition metals activated peroxodisulfate (PDS) to produce active species, which can degrade residual antibiotics in water. In this paper, Cu/CNF (carbon nanofibers) composites were first prepared by introducing Cu into CNF using electrostatic spinning technology, which was used to activate PDS to degrade tetracycline (TC). The degradation efficiency of Cu/CNF/PDS was 36.23% higher than that of CNF/PDS. The reason is that introducing Cu can increase the number of surface functional groups and specific surface area of CNF, and then improve the catalytic performance. The functional groups and Cu species are the active sites for catalytic PDS. Moreover, the main ways to degrade TC in the Cu/CNF/PDS system are singlet oxygen (1O2) and electron transfer. Based on the above analysis, we modified CNF with transition metal salts, prepared efficient environmental functional materials, and used them for PDS activation, providing a theoretical basis and technical support for the degradation of antibiotic pollutants and creating new ideas for other research.

Identification and effective regulation of scarb1 gene involved in pigmentation change in autotetraploid Carassius auratus.

The autotetraploid Carassius auratus (4nRR, 4 n=200, RRRR) is derived from whole-genome duplication of Carassius auratus red var. (RCC, 2 n=100, RR). In the current study, we demonstrated that chromatophores and pigment changes directly caused the coloration and variation of 4nRR skin (red in RCC, brownish-yellow in 4nRR). To further explore the molecular mechanisms underlying coloration formation and variation in 4nRR, we performed transcriptome profiling and molecular functional verification in RCC and 4nRR. Results revealed that scarb1, associated with carotenoid metabolism, underwent significant down-regulation in 4nRR. Efficient editing of this candidate pigment gene provided clear evidence of its significant role in RCC coloration. Subsequently, we identified four divergent scarb1 homeologs in 4nRR: two original scarb1 homeologs from RCC and two duplicated ones. Notably, three of these homeologs possessed two highly conserved alleles, exhibiting biased and allele-specific expression in the skin. Remarkably, after precise editing of both the original and duplicated scarb1 homeologs and/or alleles, 4nRR individuals, whether singly or multiply mutated, displayed a transition from brownish-yellow skin to a cyan-gray phenotype. Concurrently, the proportional areas of the cyan-gray regions displayed a gene-dose correlation. These findings illustrate the subfunctionalization of duplicated scarb1, with all scarb1 genes synergistically and equally contributing to the pigmentation of 4nRR. This is the first report concerning the functional differentiation of duplicated homeologs in an autopolyploid fish, substantially enriching our understanding of coloration formation and change within this group of organisms.

Research advances on production and application of algal biochar in environmental remediation.

Algae, comprising microalgae and macroalgae, have emerged as a promising feedstock for the production of functional biochar. Recently, the application of algal biochar in environmental remediation gains increasing attention. This review summarizes research advancements in the synthesis and application of algal biochar, a versatile and sustainable material for environmental remediation ranging from wastewater treatment to soil improvement. Algal biochar can be prepared by pyrolysis, microwave-assisted pyrolysis, and hydrothermal carbonization. Physical and chemical modifications have proven to be effective for improving biochar properties. Algal biochar is promising for removing diverse pollutants including heavy metals, organic pollutants, and microplastics. The role in soil improvement signifies a sustainable approach to enhancing soil structure, nutrient retention, and microbial activity. Research gaps are identified based on current understanding, necessitating further exploration into variations in biochar characteristics, the performance improvement, large-scale applications, and the long-term evaluation for environmental application. This review provides a better understanding of algal biochar as a sustainable and effective tool in environmental remediation.

Removal of Plastics from Micron Size to Nanoscale Using Wood Filter.

Plastic pollution, particularly microplastic (MP) and nanoplastic (NP) pollution, has become a significant concern. This study explores the use of porous wood for filtration to remove MPs and NPs and investigates their removal mechanisms. Undecorated fir wood with a thickness of 4 mm achieves a 91% removal rate for model polystyrene (PS) MPs (2.6 µm) at a water flux of 198 L/m2h. However, its separation performance for NPs (255.8 and 50.9 nm) is poor. It also shows that fir wood (coniferous wood) has a higher PS removal rate than poplar wood (hard wood). With poly dimethyl diallyl ammonium chloride (PDDA) modification, both MPs and NPs are effectively removed, with NPs' removal rate increasing from <10% to 90% for PDDA/wood. Characterization results reveal that size-exclusive interception dominates for micron-sized particles, and electrostatic interaction is crucial for nanosized particles. Additionally, intercepted NPs have been used as a strong binder for hot-pressed wood to remarkably enhance the mechanical properties of wood, suggesting a novel recycle utilization of discarded wood filters. Overall, this renewable wood material offers a simple solution for tackling MP/NP pollution.

Expression and localization of HPG axis-related genes in Carassius auratus with different ploidy.

Introduction: In the Dongting water system, the Carassius auratus (Crucian carp) complex is characterized by the coexistence of diploid forms (2n=100, 2nCC) and polyploidy forms. The diploid (2nCC) and triploid C.auratus (3n=150, 3nCC) had the same fertility levels, reaching sexual maturity at one year. Methods: The nucleotide sequence, gene expression, methylation, and immunofluorescence of the gonadotropin releasing hormone 2(Gnrh2), Gonadotropin hormone beta(Gthß), and Gonadotropin-releasing hormone receptor(Gthr) genes pivotal genes of the hypothalamic-pituitary-gonadal (HPG) axis were analyzed. Results: The analysis results indicated that Gnrh2, follicle-stimulating hormone receptor(Fshr), and Lethal hybrid rescue(Lhr) genes increased the copy number and distinct structural differentiation in 3nCC compared to that in 2nCC. The transcript levels of HPG axis genes in 3nCC were higher than 2nCC (P<0.05), which could promote the production and secretion of sex steroid hormones conducive to the gonadal development of 3nCC. Meanwhile, the DNA methylation levels in the promoter regions of the HPG axis genes were lower in 3nCC than in 2nCC. These results suggested that methylation of the promoter region had a potential regulatory effect on gene expression after triploidization. Immunofluorescence showed that the localization of the Fshß, Lhß, and Fshr genes between 3nCC and 2nCC remained unchanged, ensuring the normal expression of these genes at the corresponding sites after triploidization. Discussion: Relevant research results provide cell and molecular biology evidence for normal reproductive activities such as gonad development and gamete maturation in triploid C. auratus, and contribute to further understanding of the genetic basis for fertility restoration in triploid C. auratus.

Recent updates on remediation approaches of environmentally occurring pollutants using visible light-active nano-photocatalysts.

Photocatalysis emerges as a potential remedy for the issue of an unreliable light source. Recognized as the most dependable and potent energy source sustaining life on Earth, sunlight offers a promising solution. Sunlight is abundant and free, operational costs associated with running photocatalytic system using nanoparticles are often lower compared to system relying on artificial light source. The escalating problem of water pollution, particularly in highly industrialized nations, necessitates effective wastewater treatment methods. These methods aim to combat elevated pollution levels, encompassing pharmaceuticals, dyes, flame retardants, and pesticide components. Advanced oxidation processes within photocatalytic wastewater treatment exhibit substantial promise for removing complex organic pollutants. Doped nanomaterials, with their enhanced properties, enable efficient utilization of light. Coupled nanomaterials present significant potential in addressing both water and energy challenges by proficiently eliminating persistent pollutants from environment. Photocatalysis when exposed to sunlight can absorb photons and generate e- h + pairs. This discussion briefly outlines the wastewater treatment facilitated by interconnected nanomaterials, emphasizing their role in water-energy nexus. In exploring the capabilities of components within a functional photocatalyst, a comprehensive analysis of both simple photocatalysts and integrated photocatalytic systems is undertaken. Review aims to provide detailed explanation of the impact of light source on photon generation and significance of solar light on reaction kinetics, considering various parameters such as catalyst dosage, pH, temperature, and types of oxidants. By shedding light on these aspects, this review seeks to enhance our understanding of intricate processes involved in photocatalysis and its potential applications in addressing contemporary environmental challenges.

A review of metallurgical slags as catalysts in advanced oxidation processes for removal of refractory organic pollutants in wastewater.

With the rapid growth of the metallurgical industry, there is a significant increase in the production of metallurgical slags. The waste slags pose significant challenges for their disposal because of complex compositions, low utilization rates, and environmental toxicity. One promising approach is to utilize metallurgical slags as catalysts for treatment of refractory organic pollutants in wastewater through advanced oxidation processes (AOPs), achieving the objective of "treating waste with waste". This work provides a literature review of the source, production, and chemical composition of metallurgical slags, including steel slag, copper slag, electrolytic manganese residue, and red mud. It emphasizes the modification methods of metallurgical slags as catalysts and the application in AOPs for degradation of refractory organic pollutants. The reaction conditions, catalytic performance, and degradation mechanisms of organic pollutants using metallurgical slags are summarized. Studies have proved the feasibility of using metallurgical slags as catalysts for removing various pollutants by AOPs. The catalytic performance was significantly influenced by slags-derived catalysts, catalyst modification, and process factors. Future research should focus on addressing the safety and stability of catalysts, developing green and efficient modification methods, enhancing degradation efficiency, and implementing large-scale treatment of real wastewater. This work offers insights into the resource utilization of metallurgical slags and pollutant degradation in wastewater.

Hydrothermal treatment of alkaline red mud and sewage sludge: formation of a soil-like matrix.

Increasing attention has been focused on the comprehensive utilisation of alkaline red mud (RM) derived from the aluminium industry. Phytoremediation serves as an effective strategy, but it is limited by the drawbacks of red mud. This study proposed 'co-hydrothermally treating red mud and sewage sludge (SS)' for producing a soil-like matrix, and explored the impacts of SS addition on the characteristics of hydrothermal solid and liquid products of RM. The results showed that the introduction of SS could improve the characteristics of hydrothermal products, including pH, the particle aggregation, and organic components. During hydrothermal treatment, the acid components released from SS could neutralise the alkalinity of RM, reducing the pH of hydrothermal product from 10.1 (without SS) to and 8.2 (80% SS), respectively. With the increase of addition ratio of SS, the main range of particle size distribution in hydrothermal solid products changed from 0.1∼1 µm to 10∼100 µm, suggesting the positive role of SS in improving the particle aggregation. XRD analysis showed that the addition of SS hindered the mineral crystallization of RM during hydrothermal treatment, while FTIR and XPS analysis confirmed that SS could serve as a 'supply source' of organic components, which created favourable conditions for hydrothermal solid products as soil-like matrix. The addition ratio of SS presented the negative correlation with the pH value and positive relative with chemical oxygen demand of hydrothermal liquid products. The hydrothermal liquid product modified by SS was beneficial to further improve soil-like matrix. The strategy of co-hydrothermal treating RM and SS to produce the soil-like matrix could massively consume solid wastes, which is a prospective approach to deal with the trouble of the aluminium industry and sewage treatment plants.

Phosphorus Footprint in the Whole Biowaste-Biochar-Soil-Plant System: Reservation, Replenishment, and Reception.

Two phosphorus (P)-rich biowastes, sewage sludge (SS) and bone dreg (BD), were selected to clarify P footprints among biowaste, biochar, soil, and plants by introducing a novel "3R" concept model. Results showed that pyrolysis resulted in P transformation from an unstable-organic amorphous phase to a stable-inorganic crystalline phase with a P retention rate of 70-90% in biochar (P reservation). In soil, SSBC released more P in acid red soil and alkaline yellow soil than BDBC, while the opposite result appeared in neutral paddy soil. The P released from SSBC formed AlPO4 by combining with Al in soil, whereas P from BDBC transformed into Ca5(PO4)3F(or Cl) in conjunction with Ca in the soil (P replenishment). Various plants exhibited an uptake of approximately 2-6 times more P from biochar-amended soil than from the original soil (P reception). This study can guide the application of biochar in various soil-plant systems for effective nutrient reclamation.

Immobilization of purified enzyme EreB in metalorganic framework (MOF) mesopores for erythromycin degradation.

Erythromycin, a commonly used macrolide antibiotic, plays a crucial role in both human medicine and animal husbandry. However, its abuse has led to residual presence in the environment, with problems such as the emergence of resistant bacteria and enrichment of resistance genes. These issues pose significant risks to human health. Thus far, there are no effective, environmentally friendly methods to manage this problem. Enzymes can specifically degrade erythromycin without causing other problems, but their unrecyclability and environmental vulnerability hinder large-scale application. Enzyme immobilization may help to solve these problems. This study used Cu-BTC, a synthetic metal-organic framework, to immobilize the erythromycin-degrading enzyme EreB. The loading temperature and enzyme quantity were optimized. The Cu-BTC and EreB@Cu-BTC were characterized by various methods to confirm the preparation of Cu-BTC and immobilization of EreB. The maximum enzyme loading capacity was 66.5 mg g-1. In terms of enzymatic properties, immobilized EreB had improved heat (25-45 °C) and alkaline (6.5-10) tolerance, along with greater affinity between the enzyme and its substrate; Km decreased from 438.49 to 372.30 mM. Recycling was also achieved; after 10 cycles, 57.12% of the enzyme activity was maintained. After composite degradation, the antibacterial activity of erythromycin-containing wastewater was examined; the results showed that the novel composite could completely inactivate erythromycin. In summary, Cu-BTC was an ideal carrier for immobilization of the enzyme EreB, and the EreB@Cu-BTC composite has good prospects for the treatment of erythromycin-containing wastewater.

Machine learning: Next promising trend for microplastics study.

Microplastics (MPs), as an emerging pollutant, pose a significant threat to humans and ecosystems. However, traditional MPs characterization methods are limited by sample requirements and characterization time. Machine Learning (ML) has emerged as a vital technology for analyzing MPs pollution due to its accuracy, broad application, and powerful feature extraction. Nevertheless, environmental scientists require threshold knowledge before using ML, restricting the ML application in MPs research. Furthermore, imbalanced development of ML in MPs research is a pressing concern. In order to achieve a wide ML application in MPs research, in this review, we comprehensively discussed the size and sources of MPs datasets in relevant literature to help environmental scientists deepen their understanding of the construction of MPs datasets. Commonly used ML algorithms are analyzed from the perspective of interpretability and the need for computer facilities. Additionally, methods for improving and evaluating ML model performance, such as dataset pre-processing, model optimization, and model assessment metrics, are discussed. According to datasets and characterization techniques, MPs identification using ML was divided into three categories in this work: spectral identification, image identification, and spectral imaging identification. Finally, other applications of ML in MPs studies, including toxicity analysis, pollutants adsorption, and microbial colonization, are comprehensively discussed, which reveals the great application potential of ML. Based on the discussion above, this review suggests an algorithm selection strategy to assist researchers in selecting the most suitable ML algorithm in different situations, improving efficiency and decreasing the costs of trial and error. We believe that this work sheds light on the application of ML in MPs study.

Straw-derived biochar for the removal of antibiotics from water: Adsorption and degradation mechanisms, recent advancements and challenges.

Antibiotics, a kind of containments with the properties of widely distributed and difficult to degrade, has aroused extensive attention in the world. As a prevalent agricultural waste, straws can be utilized to prepare biochar (straw-derived biochar, SBC) to remove antibiotics from aquatic environment. To date, although a number of review papers have summarized and discussed research on biochar application in wastewater treatment and soil remediation, there are few reviews on SBC for antibiotic removal. Due to the limitations of poor adsorption and degradation performance of the pristine SBC, it is necessary to modify SBC to improve its applications for antibiotics removal. The maximum antibiotic removal capacity of modified SBC could reach 1346.55 mg/g. Moreover, the adsorption mechanisms between modified SBC and antibiotics mainly involve π-π interactions, electrostatic interactions, hydrophobic interactions, and charge dipole interactions. In addition, the modified SBC could completely degrade antibiotics within 6 min by activating oxidants, such as PS, PDS, H2O2, and O3. The mechanisms of antibiotic degradation by SBC activated oxidants mainly include free radicals (including SO4•-, •OH, and O2•-) and non-free radical pathway (such as, 1O2, electrons transfer, and surface-confined reaction). Although SBC and modified SBC have demonstrated excellent performance in removing antibiotics, they still face some challenges in practical applications, such as poor stability, high cost, and difficulties in recycling. Therefore, the further research directions and trends for the development of SBC and biochar-based materials should be taken into consideration.

Biochar/layered double hydroxides composites as catalysts for treatment of organic wastewater by advanced oxidation processes: A review.

Heterogeneous advanced oxidation process has been widely studied as an effective method for removing organic pollutants in wastewater, but the development of efficient catalysts is still challenging. This review summaries the present status of researches on biochar/layered double hydroxides composites (BLDHCs) as catalysts for treatment of organic wastewater. The synthesis methods of layered double hydroxides, the characterizations of BLDHCs, the impacts of process factors influencing catalytic performance, and research advances in various advanced oxidation processes are discussed in this work. The integration of layered double hydroxides and biochar provides synthetic effects for improving pollutant removal. The enhanced pollutant degradation in heterogeneous Fenton, sulfate radical-based, sono-assisted, and photo-assisted processes using BLDHCs have been verified. Pollutant degradation in heterogeneous advanced oxidation processes using BLDHCs is influenced by process factors such as catalyst dosage, oxidant addition, solution pH, reaction time, temperature, and co-existing substances. BLDHCs are promising catalysts due to the unique features including easy preparation, distinct structure, adjustable metal ions, and high stability. Currently, catalytic degradation of organic pollutants using BLDHCs is still in its infancy. More researches should be conducted on the controllable synthesis of BLDHCs, the in-depth understanding of catalytic mechanism, the improvement of catalytic performance, and large-scale application of treating real wastewater.

Harnessing the power of natural minerals: A comprehensive review of their application as heterogeneous catalysts in advanced oxidation processes for organic pollutant degradation.

The release of untreated wastewater into water bodies has become a significant environmental concern, resulting in the accumulation of refractory organic pollutants that pose risks to human health and ecosystems. Wastewater treatment methods, including biological, physical, and chemical techniques, have limitations in achieving complete removal of the refractory pollutants. Chemical methods, particularly advanced oxidation processes (AOPs), have gained special attention for their strong oxidation capacity and minimal secondary pollution. Among the various catalysts used in AOPs, natural minerals offer distinct advantages, such as low cost, abundant resources, and environmental friendliness. Currently, the utilization of natural minerals as catalysts in AOPs lacks thorough investigation and review. This work addresses the need for a comprehensive review of natural minerals as catalysts in AOPs. The structural characteristics and catalytic performance of different natural minerals are discussed, emphasizing their specific roles in AOPs. Furthermore, the review analyzes the influence of process factors, including catalyst dosage, oxidant addition, pH value, and temperature, on the catalytic performance of natural minerals. Strategies for enhancing the catalytic efficiency of AOPs mediated by natural minerals are explored, mainly including physical fields, reductant addition, and cocatalyst utilization. The review also examines the practical application prospects and main challenges associated with the use of natural minerals as heterogeneous catalysts in AOPs. This work contributes to the development of sustainable and efficient approaches for organic pollutant degradation in wastewater.

Formation and fine-tuning of metal-organic frameworks with carboxylic pincers for the recognition of a C2H2 tetramer and highly selective separation of C2H2/C2H4.

Highly efficient ethylene (C2H4) and acetylene (C2H2) separation is a great challenge and an important process in current industries. Herein, we finely tune a new family of 6-c metal-organic frameworks (MOFs) with crab-like carboxylic pincers for the recognition of a C2H2 tetramer and afford NTU-72 with high adsorption C2H2/C2H4 selectivity (56-441, 298 K) as well as unprecedented recovery of both highly pure C2H4 (99.95%) and C2H2 (99.36%). Furthermore, the effective binding of a C2H2 tetramer by NTU-72's carboxylic pincers has been revealed by gas-loaded crystallography and Raman spectral studies. Our work provides a novel approach for the selective binding of a small molecular cluster for designing high-performance MOFs.

The alternative transcription and expression characterization of Dmc1 in autotetraploid Carassius auratus.

Established autotetraploids often have a highly stable meiosis with high fertility compared with neo-autotetraploids. The autotetraploid Carassius auratus (4n = 200, RRRR) (4nRR), which stemmed from whole-genome duplication of Carassius auratus red var. (2n = 100, RR) (RCC), produces diploid gametes with an adopted diploid-like chromosome pairing in meiosis and maintains the formation of autotetraploid lineages. In this study, we focused on Dmc1, a meiosis-specific recombinase during the prophase of meiosis I, and elaborated on the genetic variation, alternative transcription, expression characterization, and epigenetic modification of Dmc1 in RCC and 4nRR. Two original Dmc1 from RCC were identified in 4nRR, and two duplicated Dmc1 differences in genetic composition were observed in 4nRR. Furthermore, we only noticed that one original and one duplicated Dmc1 were expressed in RCC and 4nRR, respectively. However, both possessed identical gene expression profiles, differential expression of sexual dimorphism, and hypomethylation levels. These results indicated that the specific expression of duplicated Dmc1 may be involve in the progression of meiosis of the diploid-like chromosome pairing in autotetraploid Carassius auratus. Herein, the findings significantly increase knowledge of meiosis of autopolyploid fish and provide meaningful insights into genetic breeding in polyploidy fish.

Environmental factors induced macrolide resistance genes in composts consisting of erythromycin fermentation residue, cattle manure, and maize straw.

With the growing concerns about antibiotic resistance, it is more and more important to prevent the environmental pollution caused by antibiotic fermentation residues. In this study, composted erythromycin fermentation residue (EFR) with the mixture of cattle manure and maize straw at ratios of 0:10 (CK), 1:10 (T1), and 3:10 (T2) explores the effects on physicochemical characteristics, mobile genetic elements (MGEs), and antibiotic resistance genes (ARGs). Results reflected that the addition of EFR reduced the carbon/nitrogen ratio of each compost and improved the piles' temperature, which promoted the composting process. However, the contents of Na+, SO42-, and erythromycin were also significantly increased. After 30 days of composting, the degradation rates of erythromycin in CK, T1, and T2 were 72.7%, 20.3%, and 37.1%, respectively. Meanwhile, the total positive rates for 26 detected ARGs in T1 and T2 were 65.4%, whereas that of CK was only 23.1%. Further analysis revealed that ARGs responsible for ribosomal protection, such as ermF, ermT, and erm(35), dominated the composts of T1 and T2, and most were correlated with IS613, electrical conductivity (EC), nitrogen, and Zn2+. Above all, adding EFR helps to improve the nutritional value of composts, but the risks in soil salinization and ARG enrichment caused by high EC and erythromycin content should be further investigated and eliminated.

Surface change of microplastics in aquatic environment and the removal by froth flotation assisted with cationic and anionic surfactants.

Microplastics (MPs) are increasingly released into the environment due to the widespread usage and improper management of plastics. Considerable research efforts have been devoted to the remediation of MPs. Froth flotation has been demonstrated as an effective method to remove MPs in water and sediment. However, there is a lack of knowledge on the regulation of the hydrophobicity/hydrophilicity of MPs surfaces. We found that exposure to the natural environment resulted in the increased hydrophilicity of MPs. The flotation efficiencies of polyvinyl chloride (PVC), polypropylene (PP), polystyrene (PS), and polyethylene glycol terephthalate (PET) MPs decreased to zero after six months of natural incubation in rivers. According to various characterizations, the hydrophilization mechanism is mainly correlated with surface oxidation and the deposition of clay minerals. Inspired by surface wettability conversion, we applied surfactants (collectors) to enhance MPs hydrophobicity and flotation efficiency. Anionic sodium oleate (NaOL) and cationic dodecyl trimethyl ammonium chloride (DTAC) were used to regulate surface hydrophobicity. The effects of collector concentration, pH, conditioning time, and metal ions on MPs flotation were thoroughly elucidated. Characterizations and adsorption experiments were performed to describe the heterogeneous adsorption of surfactants on MPs surfaces. The interaction between surfactants and MPs was explained through density functional theory (DFT) simulations. The dispersion energy between hydrophobic hydrocarbon chains attracts collectors on the MPs surface, and the collector molecules wrap and laminate to MPs surfaces. Flotation using NaOL exhibited a higher removal efficiency, and NaOL was environmentally friendly. Subsequently, we investigated the activation of Ca2+, Fe3+, and Al3+ to further improve the collecting efficiency of NaOL. Under the optimized conditions, MPs in natural rivers could be removed by froth flotation. This study shows the great promise of froth flotation for the application of MPs removal.