Germanene saturable absorber for mode-locked operation in an all-fiber laser with multiple dispersion environments.

In this paper, a high-quality germanene-polyvinyl alcohol (PVA) saturable absorber (SA) with a modulation depth of 3.05% and a saturation intensity of 17.95M W/c m 2 was prepared. Stable conventional mode-locking and harmonic mode-locking (HML) were achieved in germanene-based Er-doped fiber lasers (EDFL) using dispersion management techniques. In a cavity with a net dispersion value of -0.22p s 2, the conventional soliton had a center wavelength of 1558.2 nm, a repetition frequency of 19.09 MHz, and a maximum 3 dB spectrum bandwidth of 3.5 nm. The highest repetition frequencies achieved in cavities with net dispersion values of -2.81p s 2, -1.73p s 2, and -1.09p s 2 were 9.48 MHz, 12.75 MHz, and 12.10 MHz for HML, respectively. Furthermore, the effects of dispersion, power, and the polarization state on HML were systematically investigated. Our research results fully demonstrate the capability of germanene as an optical modulator in generating conventional mode-locked and harmonic mode-locked solitons. This provides meaningful references for promoting its application in ultrafast fiber lasers.

Evolution between bright and dark pulses in a MoxW1-xTe2 based fiber laser.

We proposed an erbium-doped fiber laser mode-locked with a MoxW1-xTe2-based nonlinear optical modulator for the first time to our best knowledge. This fiber laser can deliver bright pulses, bright-dark pulse pairs, dark pulses, bright-dark-bright pulses, and dark-dark-bright pulses. The modulation depth and saturation intensity of the MoxW1-xTe2-based saturable absorber were about 7.8% and 8.6 MW/cm2, respectively. When 10% of the laser in the cavity was output, conventional soliton pulses with central wavelength of 1560.1 nm can be obtained in the cavity. When 70% of the laser was output, dual-wavelength domain-wall dark pulses appeared in the laser cavity. This experiment revealed that an appropriate increase in the ratio of output energy can improve the chance of dark pulses in fiber lasers. The mode-locking states in this fiber laser can evolve with each other between bright pulses, bright-dark pulse pairs and dark pulses by adjusting the polarization controller. The results indicated that the MoxW1-xTe2 can be used to make modulators for generating dark pulses. Furthermore, our work will be of great help to improve the chance of the generation of dark pulse in fiber lasers.

High-Energy Mode-Locked Pulse Er-Doped Fiber Laser-Based GeTe as Saturable Absorber.

High-energy Er-doped fiber laser with high conversion efficiency is reported, which is mode-locked by a germanium telluride (GeTe)-based saturable absorber (SA). By adjusting the direction of the polarization controller (PC), a high-energy pulse with a central wavelength of 1533.1 nm and a fundamental repetition frequency of 1.58 MHz is achieved. Under the pump power of 450.1 mW, the maximum average output power is 50.48 mW, and the single-pulse energy is 32 nJ. It is worth noting that the optical-to-optical conversion efficiency has reached about 11.2%. The experimental results indicate that GeTe performs excellently as SAs for obtaining mode-locked fiber lasers and plays an extremely important role in high-energy fiber lasers.

Nanosized indium selenide saturable absorber for multiple solitons operation in Er3+-doped fiber laser.

With the advances in the field of ultrafast photonics occurring so fast, the demand for optical modulation devices with high performance and soliton lasers which can realize the evolution of multiple soliton pulses is gradually increasing. Nevertheless, saturable absorbers (SAs) with appropriate parameters and pulsed fiber lasers which can output abundant mode-locking states still need to be further explored. Due to the special band gap energy values of few-layer indium selenide (InSe) nanosheets, we have prepared a SA based on InSe on a microfiber by optical deposition. In addition, we demonstrate that our prepared SA possesses a modulation depth and saturable absorption intensity about 6.87% and 15.83 MW/cm2, respectively. Then, multiple soliton states are obtained by dispersion management techniques, including regular solitons, and second-order harmonic mode-locking solitons. Meanwhile, we have obtained multi-pulse bound state solitons. We also provide theoretical basis for the existence of these solitons. The results of the experiment show that the InSe has the potential to be an excellent optical modulator because of its excellent saturable absorption properties. This work also is important for improving the understanding and knowledge of InSe and the output performance of fiber lasers.

Generation of bright-dark solitons in an Er-doped fiber laser employing InSb as a saturable absorber.

In this paper, an indium antimonide (InSb) saturable absorber (SA) was successfully fabricated. The saturable absorption properties of the InSb SA were studied, and they show a modulation depth and a saturable intensity of 5.17% and 9.23M W/c m 2, respectively. By employing the InSb SA and building the ring cavity laser structure, the bright-dark soliton operations were successfully obtained by increasing the pump power to 100.4 mW and adjusting the polarization controller. As the pump power increased from 100.4 to 180.3 mW, the average output power increased from 4.69 to 9.42 mW, the corresponding fundamental repetition rate was 2.85 MHz, and the signal-to-noise ratio was 68 dB. The experimental results show that InSb with excellent saturable absorption characteristics can be used as a SA to obtain pulse lasers. Therefore, InSb has important potential in fiber laser generation, further applications in optoelectronics, laser distance ranging, and optical fiber communication, and it can be widely developed.

Dual-shearing interferometer for multi-modal hyperspectral imaging.

A dual-shearing interferometer (DSI) for multimodal hyperspectral imaging is presented. Two orthogonally stacked pairs of coherent beams are generated by a pair of novel, to the best of our knowledge, birefringent lateral shearing splitters. Consequently, two sets of interferograms with full pixel resolution are captured alternately in a time sequence in the double Nyquist frequency mode. Modals of dual-field-of-view hyperspectral imaging and differential-polarization hyperspectral imaging are introduced, and verification experiments are performed. The feasibility of other modals is discussed. The proposed method can effectively improve the instrument's performance in terms of the field of view, polarization, spectral resolution, and spectral range.

Generation of bright-dark soliton pairs based on a ferromagnetic insulator Cr2Si2Te6 as a modulator in an Er-doped fiber laser.

In this work, a saturable absorber (SA) based on Cr2Si2Te6 (CST), with a modulation depth of 14.90% and saturation intensity of 4.81MW/cm2, was prepared by a liquid phase stripping method. Its nonlinear optical properties and application in obtaining mode-locked pulse output of bright-dark solitons are studied. When the pump power was 1250 mW, the maximum output power was 26.60 mW; the energy of the single pulse was 15.02 nJ, and the repetition rate was 1.77 MHz. Our results provided evidence that CST can be used as an excellent SA for a mode-locked laser and demonstrated that ferromagnetic insulators can be used for the study of bright-dark soliton pairs.

Passively mode-locked Er-doped fiber laser based on a ferromagnetic insulator Cr2Si2Te6 as a saturable absorber.

In our work, a new-type, to the best of our knowledge, ferromagnetic insulator and its nonlinear optical absorption characteristics and related ultrafast modulation applications were investigated. Cr2Si2Te6 saturable absorbers (SAs) with a modulation depth and a saturable intensity of 9.7% and 3.5MW/cm2 were fabricated. By adjusting the pump power to 120 mW and optimizing the polarization state, traditional soliton operations were obtained successfully; the corresponding duration of pulse and the fundamental repetition rate were ∼1.33ps and 6.70 MHz, and the signal-to-noise ratio was 50 dB. The experimental results reveal that Cr2Si2Te6 with excellent saturable absorption characteristics can be used as a SA to obtain ultrafast pulse lasers.

Passively mode-locked fiber laser based on GeTe as a saturable absorber.

In this work, we fabricate a saturable absorber based on GeTe with saturation intensity and modulation depth of 12.6M W/c m 2 and 7%, respectively. We obtain stable conventional soliton and stretched soliton mode-locking operation. For the conventional soliton state, the average output power increased from 0.93 to 8.70 mW with the increase of pump power, and the fundamental repetition rate was 7.8351 MHz. Its central wavelength and 3 dB bandwidth were 1564.72 and 4.78 nm, respectively. For the stretched soliton state, when the pump power was increased from 87.4 to 420.3 mW, the average output power increased from 2.05 to 10.46 mW. When the maximum average output power reached 10.46 mW, the maximum average single-pulse energy was 0.86 nJ. The experimental results show that GeTe nanosheets will have broad application potential in the field of ultrafast photonics.

Passively Q-switched and mode-locked erbium-doped fiber lasers based on tellurene nanosheets as saturable absorber.

Various two-dimensional (2D) materials show unique optical properties and excellent performance in acting as saturable absorber (SA) for demonstrating all-fiber ultra-fast lasers. Tellurene, as a new-fashioned few-layer 2D monoelemental material, was designed as an excellent saturable absorber to achieve Q-switched and mode-locked operations within erbium-doped fiber (EDF) lasers in our experiment. High-quality tellurene-based SA with a modulation depth of 0.97% was obtained by blending few-layer tellurene nanosheet solution prepared by liquid phase exfoliation method and the polyvinyl alcohol (PVA) solution. Inserting the SA into the EDF laser cavity by sandwiching the tellurene-PVA film between two fiber ferrules, either the passively Q-switched or the passively mode-locked operations can be obtained. The repetition rate varies from 15.92 to 47.61 kHz, and the pulse duration decreases from 8.915 to 5.196 µs in the passively Q-switched operation. To the best of our knowledge, this is the first demonstration focusing on the modulation application of tellurene in designing Q-switched pulsed laser operations. Additionally, mode-locked operations were also achieved by adjusting the polarization state. The obtained results fully indicate that tellurene can be developed as an efficient SA for pulsed fiber lasers.

Molecular Mapping of Fusarium Head Blight Resistance in the Spring Wheat Line ND2710.

ND2710 is a hard red spring wheat line with a very high level of resistance to Fusarium head blight (FHB). It was selected from the progeny of a cross between ND2603 (an advanced breeding line derived from the Sumai 3/Wheaton cross) and Grandin (a spring wheat cultivar). The FHB resistance of ND2710 is presumably derived from Sumai 3 because the other parents (Grandin and Wheaton) are very susceptible to FHB. To identify and map the quantitative trait loci (QTL) for FHB resistance in ND2710, we developed a mapping population consisting of 233 recombinant inbred lines (RILs) from the cross between ND2710 and the spring wheat cultivar Bobwhite. These RILs along with their parents and checks were evaluated for reactions to FHB in three greenhouse experiments and one field experiment during 2013 to 2014. The population was also genotyped with the wheat 90K iSelect single-nucleotide polymorphism (SNP) assay, and a genetic linkage map was developed with 1,373 non-cosegregating SNP markers, which were distributed on all 21 wheat chromosomes spanning 914.98 centimorgans of genetic distance. Genetic analyses using both phenotypic and genotypic data identified one major QTL (Qfhb.ndwp-3B) on the short arm of chromosome 3B, and three minor QTL (Qfhb.ndwp-6B, Qfhb.ndwp-2A, and Qfhb.ndwp-6A) on 6B, 2A, and 6A, respectively. The major QTL on 3B was detected in all experiments and explained 5 to 20% of the phenotypic variation, while the three minor QTL on 6B, 2A, and 6A explained 5 to 12% phenotypic variation in at least two experiments, except for Qfhb.ndwp-2A, which was only detected in the field experiment. Qfhb.ndwp-3B and Qfhb.ndwp-6B were mapped to the genomic regions containing Fhb1 and Fhb2, respectively, confirming that they originated from Sumai 3. The additive effect of the major and minor QTL may contribute to the high level of FHB resistance in ND2710. The SNP markers closely linked to the FHB resistance QTL will be useful for marker-assisted selection of FHB resistance in wheat breeding programs.

MSH1-induced non-genetic variation provides a source of phenotypic diversity in Sorghum bicolor.

MutS Homolog 1 (MSH1) encodes a plant-specific protein that functions in mitochondria and chloroplasts. We showed previously that disruption or suppression of the MSH1 gene results in a process of developmental reprogramming that is heritable and non-genetic in subsequent generations. In Arabidopsis, this developmental reprogramming process is accompanied by striking changes in gene expression of organellar and stress response genes. This developmentally reprogrammed state, when used in crossing, results in a range of variation for plant growth potential. Here we investigate the implications of MSH1 modulation in a crop species. We found that MSH1-mediated phenotypic variation in Sorghum bicolor is heritable and potentially valuable for crop breeding. We observed phenotypic variation for grain yield, plant height, flowering time, panicle architecture, and above-ground biomass. Focusing on grain yield and plant height, we found some lines that appeared to respond to selection. Based on amenability of this system to implementation in a range of crops, and the scope of phenotypic variation that is derived, our results suggest that MSH1 suppression provides a novel approach for breeding in crops.

Identification of genetic factors controlling kernel hardness and related traits in a recombinant inbred population derived from a soft × 'extra-soft' wheat (Triticum aestivum L.) cross.

Kernel hardness or texture, used to classify wheat (Triticum aestivum L.) into soft and hard classes, is a major determinant of milling and baking quality. Wheat genotypes in the soft class that are termed 'extra-soft' (with kernel hardness in the lower end of the spectrum) have been associated with superior end-use quality. In order to better understand the relationship between kernel hardness, milling yield, and various agronomic traits, we performed quantitative trait mapping using a recombinant inbred line population derived from a cross between a common soft wheat line and a genotype classified as an 'extra-soft' line. A total of 47 significant quantitative trait loci (QTL) (LOD ≥ 3.0) were identified for nine traits with the number of QTL affecting each trait ranging from three to nine. The percentage of phenotypic variance explained by these QTL ranged from 3.7 to 50.3%. Six QTL associated with kernel hardness and break flour yield were detected on chromosomes 1BS, 4BS, 5BS, 2DS, 4DS, and 5DL. The two most important QTL were mapped onto orthologous regions on chromosomes 4DS (Xbarc1118-Rht-D1) and 4BS (Xwmc617-Rht-B1). These results indicated that the 'extra-soft' characteristic was not controlled by the Hardness (Ha) locus on chromosome 5DS. QTL for eight agronomic traits occupied two genomic regions near semi-dwarf genes Rht-D1 on chromosome 4DS and Rht-B1 on chromosome 4BS. The clustering of these QTL is either due to the pleiotropic effects of single genes or tight linkage of genes controlling these various traits.