First Principles Investigation of C, Cl2 and CO Co-Adsorption on ZrSiO4 Surfaces for Carbochlorination Reaction.

The study of the adsorption behavior of C, CO and Cl2 on the surface of ZrSiO4 is of great significance for the formulation of the technological parameters in the carbochlorination reaction process. Based on first principles, the adsorption structure, adsorption energy, Barder charge, differential charge density, partial density of states and energy barrier were calculated to research the adsorption and reaction mechanism of C and Cl2 on ZrSiO4 surfaces. The results indicated that when C, CO and Cl2 co-adsorbed on the surface of ZrSiO4, they interacted with surface atoms and the charge transfer occurred. The Cl2 molecules dissociated and formed Zr-Cl bonds, while C atoms formed C1=O1 bonds with O atoms. Compared with CO, the co-adsorption energy and reaction energy barrier of C and Cl2 are lower, and the higher the C content, the lower the adsorption energy and energy barrier, which is beneficial for promoting charge transfer and the dissociation of Cl2. The 110-2C-2Cl2 has the lowest adsorption energy and the highest reaction activity, with adsorption energy and energy barriers of -13.45 eV and 0.02 eV. The electrons released by C are 2.30 e, while the electrons accepted by Cl2 are 2.37 e.

Efficient Inverted Perovskite Photovoltaics Through Surface State Manipulation.

Inverted perovskite solar cells (PSCs) are considered as the most promising avenue for the commercialization of PSCs due to their potential inherent stability. However, suboptimal interface contacts between electron transport layer (ETL) (such as C60) and the perovskite absorbing layer within inverted PSCs always result in reduced efficiency and poor stability. Herein, a surface state manipulation strategy has been developed by employing a highly electronegative 4-fluorophenethylamine hydrochloride (p-F-PEACl) to effectively address the issue of poor interface contacts in the inverted PSCs. The p-F-PEACl demonstrates a robust interaction with perovskite film through bonding of amino group and Cl- with I- and Pb2+ ions in the perovskite, respectively. As such, the surface defects of perovskite film can be significantly reduced, leading to suppressed non-radiative recombination. Moreover, p-F-PEACl also plays a dual role in enhancing the surface potential and improving energy-level alignment at the interfaces between the perovskite and C60 carrier transport layer, which directly contributes to efficient charge extraction. Finally, the open-circuit voltage (Voc) of devices increases from 1.104 V to 1.157 V, leading to an overall efficiency improvement from 22.34% to 24.78%. Furthermore, the p-F-PEACl-treated PSCs also display excellent stability.

Modulation of Charge Transport from Two-Dimensional Perovskites to Industrial Charge Transport Layers by the Organic Spacer-Dependent Exciton-Phonon Interactions.

In the past decade, two-dimensional (2D) perovskite surface treatment has emerged as a promising strategy to improve the performance of three-dimensional (3D) perovskite solar cells (PSCs). However, systematic studies on the impact of organic spacers of 2D perovskites on charge transport in 2D/3D PSCs are still lacking. Here, using 2D perovskite film/C60 heterostructures with different organic spacers [butylamine (BA), phenylethylamine (PEA), and 3-fluorophenethylamine (m-F-PEA)], we systematically investigated the carrier diffusion and interfacial transfer process. Using a 2D perovskite film with a thickness of ∼7 nm, we observed subtle differences in electron transfer time between 2D perovskites and C60 layers, which can be attributed to limited thickness and similar electron coupling strength. However, with the thickness of 2D perovskite increasing, electron transfer efficiency in the (BA)2PbI4/C60 heterostructure exhibits the most rapid decrease due to poor carrier diffusion of (BA)2PbI4 caused by stronger exciton-phonon interactions compared to (PEA)2PbI4 and (m-F-PEA)2PbI4 in thickness-dependent charge transfer research. Meanwhile, the fill factor of 2D/3D PSC treated with BAI exhibits the most rapid decrease compared to PEAI- and m-F-PEAI-treated 2D/3D PSCs with the concentration increase of passivators. This study indicates that it is easier to enhance open-circuit voltages and minimize the decrease of fill factor by increasing the concentration of passivators in 2D/3D PSCs when using passivators with a rigid molecular structure.

Post-Treatment-Free Dual-Interface Passivation via Facile 1D/3D Perovskite Heterojunction Construction.

For achieving high-efficiency perovskite solar cells, it is almost always necessary to substantially passivate defects and protect the perovskite structure at its interfaces with charge transport layers. Such a modification generally involves the post-treatment of the deposited perovskite film by spin coating, which cannot meet the technical demands of scaling up the production of perovskite photovoltaics. In this work, we demonstrate one-step construction of buried and capped double 1D/3D heterojunctions without the need for any post-treatment, which is achieved through facile tetraethylammonium trifluoroacetate (TEATFA) prefunctionalization on the SnO2 substrate. The functional TEATFA salt is first deposited onto the SnO2 substrate and reacts on this buried interface. Once the FAPbI3 perovskite precursor solution is dripped, a portion of the TEA+ cations spontaneously diffuse to the top surface over film crystallization. The TEATFA-based water-resistant 1D/3D TEAPbI3/FAPbI3 heterojunctions at both the buried and capped interfaces lead to much better photovoltaic performance and higher operational stability. Since this approach saves the need for any postsynthesis passivation, its feasibility for the fabrication of large-area perovskite photovoltaics is also showcased. Compared to ∼15% for a pristine 5 cm × 5 cm FAPbI3 mini-module without postsynthesis passivation, over 20% efficiency is achieved following the proposed route, demonstrating its great potential for larger-scale fabrication with fewer processing steps.

A Review of Robotic Fish Based on Smart Materials.

The present study focuses on summarizing the recent advancements in the field of fish swimming mode research and bionic robotic fish prototypes based on smart materials. It has been widely acknowledged that fish exhibit exceptional swimming efficiency and manoeuvrability compared to conventional underwater vehicles. In the pursuit of developing autonomous underwater vehicles (AUVs), conventional experimental methods often prove to be complex and expensive. Hence, the utilization of computer simulations for hydrodynamic modelling provides a cost-effective and efficient approach for analysing the swimming behaviour of bionic robotic fish. Additionally, computer simulations can provide data that are difficult to obtain through experimental methods. Smart materials, which integrate perception, drive, and control functions, are increasingly being applied to bionic robotic fish research. However, the utilization of smart materials in this field is still an area of ongoing research and several challenges remain unresolved. This study provides an overview of the current state of research on fish swimming modes and the development of hydrodynamic modelling. The application of four distinct types of smart materials in bionic robotic fish is then reviewed, with a focus on analysing the advantages and disadvantages of each material in driving swimming behaviour. In conclusion, the paper highlights the key technical challenges that must be addressed for the practical implementation of bionic robotic fish and provides insights into the potential future directions of this field.

Functional organic cation induced 3D-to-0D phase transformation and surface reconstruction of CsPbI3 inorganic perovskite.

Efficiency and stability are the main research focuses for perovskite solar cells. Inorganic perovskites like CsPbI3 possess higher chemical stability than those with organic A-site cations, while they also exhibit higher defect density. Nonetheless, it is highly challenging to induce orderly secondary arrangement or reconstruction of inorganic perovskites with reduced defects because of their unique chemical properties. In this work, in-situ three-dimension-to-zero-dimension (3D-to-0D) phase transformation and surface reconstruction on CsPbI3 film is achieved as induced by a functional organic cation, benzyldodecyldimethylammonium (BDA), a process of which that is similar to phase-transfer catalysis. With the help of BDABr salt treatment, 0D Cs4PbI6 perovskites are secondarily formed along CsPbI3 grain boundaries with Cs-related cationic defects passivated, yielding structures of higher stability. The BDA-CsPbI3 films exhibit reduced non-radiative recombination and promoted charge transfer, leading to inorganic perovskite solar cells with a high power conversion efficiency of 20.63% and good operational stability.

Solution chemistry quasi-epitaxial growth of atomic CaTiO3 perovskite layers to stabilize and passivate TiO2 photoelectrodes for efficient water splitting.

Perovskite oxides with unique crystal structures and high defect tolerance are promising as atomic surface passivation layers for photoelectrodes for efficient and stable water splitting. However, controllably depositing and crystalizing perovskite-type metal oxides at the atomic level remains challenging, as they usually crystalize at higher temperatures than regular metal oxides. Here, we report a mild solution chemistry approach for the quasi-epitaxial growth of an atomic CaTiO3 perovskite layer on rutile TiO2 nanorod arrays. The high-temperature crystallization of CaTiO3 perovskite is overcome by a sequential hydrothermal conversion of the atomic amorphous TiOx layer to CaTiO3 perovskite. The atomic quasi-epitaxial CaTiO3 layer passivated TiO2 nanorod arrays exhibit more efficient interface charge transfer and high photoelectrochemical performance for water splitting. Such a mild solution-based approach for the quasi-epitaxial growth of atomic metal oxide perovskite layers could be a promising strategy for both fabricating atomic perovskite layers and improving their photoelectrochemical properties.

Decoupling engineering of formamidinium-cesium perovskites for efficient photovoltaics.

Although pure formamidinium iodide perovskite (FAPbI3) possesses an optimal gap for photovoltaics, their poor phase stability limits the long-term operational stability of the devices. A promising approach to enhance their phase stability is to incorporate cesium into FAPbI3. However, state-of-the-art formamidinium-cesium (FA-Cs) iodide perovskites demonstrate much worse efficiency compared with FAPbI3, limited by the different crystallization dynamics of formamidinium and cesium, which result in poor composition homogeneity and high trap densities. We develop a novel strategy of crystallization decoupling processes of formamidinium and cesium via a sequential cesium incorporation approach. As such, we obtain highly reproducible, highly efficient and stable solar cells based on FA1 - x Cs x PbI3 (x = 0.05-0.16) films with uniform composition distribution in the nanoscale and low defect densities. We also revealed a new stabilization mechanism for Cs doping to stabilize FAPbI3, i.e. the incorporation of Cs into FAPbI3 significantly reduces the electron-phonon coupling strength to suppress ionic migration, thereby improving the stability of FA-Cs-based devices.

Stable Pure Iodide MA0.95Cs0.05PbI3 Perovskite toward Efficient 1.6 eV Bandgap Photovoltaics.

Perovskite photovoltaics with the advantages of facile fabrication and high efficiency have been the rising star in the field for a decade. Methylammonium lead triiodide (MAPbI3) was the first widely studied perovskite to initiate the boom of perovskite photovoltaics, but it was later considered thermodynamically instable for commercialization. Here, we demonstrate that simple cesium (Cs) doping without any complicated process can form a stable MA-based perovskite with a widened bandgap, which may broaden the application of MA-based perovskites in tandem solar cells. A record-high efficiency of ≤22% is thus achieved for a 1.6 eV bandgap perovskite solar cell. This work not only provides a new stable and efficient pure iodide candidate as a 1.6 eV bandgap perovskite but also reveals that Cs incorporation can help improve the efficiency and stability of MA-based perovskites.

Mitochondria-Targeted Degradable Nanocomposite Combined with Laser and Ultrasound for Synergistic Tumor Therapies.

Although the development of safe and efficient cancer therapeutic agents is essential, this process remains challenging. In this study, a mitochondria-targeted degradable nanoplatform (PDA-MnO2-IR780) for synergistic photothermal, photodynamic, and sonodynamic tumor treatment was investigated. PDA-MnO2-IR780 exhibits superior photothermal properties owing to the integration of polydopamine, MnO2, and IR780. IR780, a photosensitizer and sonosensitizer, was used for photodynamic therapy and sonodynamic therapy. When PDA-MnO2-IR780 was delivered to the tumor site, MnO2 was decomposed by hydrogen peroxide, producing Mn2+ and oxygen. Meanwhile, alleviating tumor hypoxia promoted the production of reactive oxygen species during photodynamic therapy and sonodynamic therapy. Moreover, large amounts of reactive oxygen species could reduce the expression of heat shock proteins and increase the heat sensitivity of tumor cells, thereby improving the photothermal treatment effect. In turn, hyperthermia caused by photothermal therapy accelerated the production of reactive oxygen species in photodynamic therapy. IR780 selectively accumulation in mitochondria also promoted tumor apoptosis. In this system, the mutual promotion of photothermal therapy and photodynamic therapy/sonodynamic therapy had an enhanced therapeutic effect. Moreover, the responsive degradable characteristic of PDA-MnO2-IR780 in the tumor microenvironment ensured excellent biological safety. These results reveal a great potential of PDA-MnO2-IR780 for safe and highly-efficiency synergistic therapy for cancer.

Zwitterion-Functionalized SnO2 Substrate Induced Sequential Deposition of Black-Phase FAPbI3 with Rearranged PbI2 Residue.

Black-phase formamidinium lead iodide (FAPbI3 ) with narrow bandgap and high thermal stability has emerged as the most promising candidate for highly efficient and stable perovskite photovoltaics. In order to overcome the intrinsic difficulty of black-phase crystallization and to eliminate the lead iodide (PbI2 ) residue, most sequential deposition methods of FAPbI3 -based perovskite will introduce external ions like methylammonium (MA+ ), cesium (Cs+ ), and bromide (Br- ) ions to the perovskite structure. Here a zwitterion-functionalized tin(IV) oxide (SnO2 ) is introduced as the electron-transport layer (ETL) to induce the crystallization of high-quality black-phase FAPbI3 . The SnO2 ETL treated with the zwitterion of formamidine sulfinic acid (FSA) can help rearrange the stack direction, orientation, and distribution of residual PbI2 in the perovskite layer, which reduces the side effect of the residual PbI2 . Besides, the FSA functionalization also modifies SnO2 ETL to suppress deep-level defects at the perovskite/SnO2 interface. As a result, the FSA-FAPbI3 -based perovskite solar cells (PSCs) exhibit an excellent power conversion efficiency of up to 24.1% with 1000 h long-term operational stability. These findings provide a new interface engineering strategy on the sequential fabrication of black-phase FAPbI3 PSCs with improved optoelectronic performance.

Hot Deformation Behavior of the 25CrMo4 Steel Using a Modified Arrhenius Model.

25CrMo4 steel is widely used in the manufacturing of high-speed train axles due to its excellent mechanical properties. The purpose of this study is to develop an accurate modified constitutive model to describe the hot deformation behavior of the steel. Isothermal compression experiments were performed at different strain rates (0.01, 0.1, 0.5, and 1 s-1) and different temperatures (950, 1000, 1050, and 1100 °C) using a Gleeble-3800 thermal simulator. The microstructure after hot deformation was observed by the electron backscatter diffraction (EBSD), and the effects of temperature and strain rate were analyzed. The results showed that the coupling effect of temperature and strain rate on the dislocation density led to the change in the shape of the true stress-strain curve and that dynamic recovery (DRV) and dynamic recrystallization (DRX) caused the macroscopic softening phenomenon, with DRX being the main mechanism. Based on the true stress-strain curves, the strain-compensated Arrhenius constitutive model was calibrated. To improve prediction ability, a modified Arrhenius constitutive model was proposed, in which the temperature and strain rate coupling correction functions were incorporated. The original, modified Arrhenius models were evaluated according to the absolute relative error (ARE), the average absolute relative error (AARE), and the correlation coefficient (R2). Compared with the original model, the modified Arrhenius model has a higher prediction accuracy, with the ARE value mostly below 4%, the AARE value of 1.91%, and the R2 value of 0.9958.

The Chemical Design in High-Performance Lead Halide Perovskite: Additive vs Dopant?

Metal halide perovskite solar cells (PSCs) have attracted enormous attention as one of the most promising candidates for next-generation photovoltaics in the past few years. During the development of PSCs, various chemicals have been added to improve film quality and device performance. However, there are still debates about whether these chemicals are additives as removed from the final film or dopants incorporated into the crystal lattice. It is important to clarify whether these added chemicals are additives or dopants when designed for high-quality perovskite films' fabrications. Herein, we summarized several commonly used chemicals for hybrid and all-inorganic perovskites, such as MACl, DMAI, MAAc, and alkali metal cations. The underlying mechanism and their roles during the formation of perovskite films were discussed. In the end, we proposed some conclusive important factors to clarify additives and dopants, which would be helpful for the further chemical design for improving high-performance perovskite devices.

MA Cation-Induced Diffusional Growth of Low-Bandgap FA-Cs Perovskites Driven by Natural Gradient Annealing.

Low-bandgap formamidinium-cesium (FA-Cs) perovskites of FA1-x Cs x PbI3 (x < 0.1) are promising candidates for efficient and robust perovskite solar cells, but their black-phase crystallization is very sensitive to annealing temperature. Unfortunately, the low heat conductivity of the glass substrate builds up a temperature gradient within from bottom to top and makes the initial annealing temperature of the perovskite film lower than the black-phase crystallization point (~150°C). Herein, we take advantage of such temperature gradient for the diffusional growth of high-quality FA-Cs perovskites by introducing a thermally unstable MA+ cation, which would firstly form α-phase FA-MA-Cs mixed perovskites with low formation energy at the hot bottom of the perovskite films in the early annealing stage. The natural gradient annealing temperature and the thermally unstable MA+ cation then lead to the bottom-to-top diffusional growth of highly orientated α-phase FA-Cs perovskite, which exhibits 10-fold of enhanced crystallinity and reduced trap density (~3.85 × 1015 cm-3). Eventually, such FA-Cs perovskite films were fabricated into stable solar cell devices with champion efficiency up to 23.11%, among the highest efficiency of MA-free perovskite solar cells.

Efficient and Stable CsPbI3 Inorganic Perovskite Photovoltaics Enabled by Crystal Secondary Growth.

Defect-triggered phase degradation is generally considered as the main issue that causes phase instability and limited device performance for CsPbI3 inorganic perovskites. Here, a defect compensation in CsPbI3 perovskite through crystal secondary growth of inorganic perovskites is demonstrated, and highly efficient inorganic photovoltaics are realized. This secondary growth is achieved by a solid-state reaction between a bromine salt and defective CsPbI3 perovskite. Upon solid-state reaction, the Br- ions can diffuse over the entire CsPbI3 perovskite layer to heal the undercoordinated Pb2+ and conduct certain solid-state I/Br ion exchange reaction, while the organic cations can potentially heal the Cs+ cation vacancies through coupling with [PbI6 ]4- octahedra. The carrier dynamics confirm that this crystal secondary growth can realize defect compensation in CsPbI3 . The as-achieved defect-compensated CsPbI3 not only improves the charge dynamics but also enhances the photoactive phase stability. Finally, the CsPbI3 -based solar cell delivers 20.04% efficiency with excellent operational stability. Overall, this work proposes a novel concept of defect compensation in inorganic perovskites through crystal secondary growth induced by solid-state reaction that is promising for various optoelectronic applications.

Incorporation of Two-Dimensional WSe2 into MAPbI3 Perovskite for Efficient and Stable Photovoltaics.

Achieving reduced defect density and efficient charge carrier extraction plays a vital role for efficient and stable perovskite solar cells (PSCs). Over the course of technical development, it is desired to use one single material or approach to synergistically passivate defects and enhance the charge extraction. In this work, we developed an effective strategy for obtaining efficient and stable PSCs via incorporating quasi-monolayer two-dimensional WSe2 into the MAPbI3 perovskite layer. The addition of WSe2 helps with the formation of perovskite film with higher quality and also passivates the Pb-related defects through Pb-Se coordination bonding. MAPbI3/WSe2 shows a more matched energy-level alignment between the perovskite layer and hole transport layer for accelerated hole extraction. Consequently, the performances of PSCs significantly improved with power conversion efficiency increase from 19.2% to 21.2% after the incorporation of WSe2. Accordingly, the MAPbI3/WSe2-based PSCs exhibit well-improved photostability with suppression of Pb0 defect formation.

Using steric hindrance to manipulate and stabilize metal halide perovskites for optoelectronics.

The chemical instability of metal halide perovskite materials can be ascribed to their unique properties of softness, in which the chemical bonding between metal halide octahedral frameworks and cations is the weak ionic and hydrogen bonding as in most perovskite structures. Therefore, various strategies have been developed to stabilize the cations and metal halide frameworks, which include incorporating additives, developing two-dimensional perovskites and perovskite nanocrystals, etc. Recently, the important role of utilizing steric hindrance for stabilizing and passivating perovskites has been demonstrated. In this perspective, we summarize the applications of steric hindrance in manipulating and stabilizing perovskites. We will also discuss how steric hindrance influences the fundamental kinetics of perovskite crystallization and film formation processes. The similarities and differences of the steric hindrance between perovskite solar cells and perovskite light emission diodes are also discussed. In all, utilizing steric hindrance is a promising strategy to manipulate and stabilize metal halide perovskites for optoelectronics.

Organic Tetrabutylammonium Cation Intercalation to Heal Inorganic CsPbI3 Perovskite.

The in situ formation of reduced dimensional perovskite layer via post-synthesis ion exchange has been an effective way of passivating organic-inorganic hybrid perovskites. In contrast, cesium ions in Cs-based inorganic perovskite with strong ionic binding energy cannot exchange with those well-known organic cations to form reduced dimensional perovskite. Herein, we demonstrate that tetrabutylammonium (TBA+ ) cation can intercalate into CsPbI3 to effectively substitute the Cs cation and to form one-dimensional (1D) TBAPbI3 layer in the post-synthesis TBAI treatment. Such TBA cation intercalation leads to in situ formation of TBAPbI3 protective layer to heal defects at the surface of inorganic CsPbI3 perovskite. The TBAPbI3 -CsPbI3 perovskite exhibited enhanced stability and lower defect density, and the corresponding perovskite solar cell devices achieved an improved efficiency up to 18.32 % compared to 15.85 % of the control one.

Self-Amplification of Coherent Energy Modulation in Seeded Free-Electron Lasers.

The spectroscopic techniques for time-resolved fine analysis of matter require coherent x-ray radiation with femtosecond duration and high average brightness. Seeded free-electron lasers (FELs), which use the frequency up-conversion of an external seed laser to improve temporal coherence, are ideal for providing fully coherent soft x-ray pulses. However, it is difficult to operate seeded FELs at a high repetition rate due to the limitations of present state-of-the-art laser systems. Here, we report a novel self-modulation method for enhancing laser-induced energy modulation, thereby significantly reducing the requirement of an external laser system. Driven by this scheme, we experimentally realize high harmonic generation in a seeded FEL using an unprecedentedly small external laser-induced energy modulation. An electron beam with a laser-induced energy modulation as small as 1.8 times the slice energy spread is used for lasing at the seventh harmonic of a 266-nm seed laser in a single-stage high-gain harmonic generation (HGHG) setup and the 30th harmonic of the seed laser in a two-stage HGHG setup. The results mark a major step toward a high-repetition-rate, fully coherent x-ray FEL.