Process for Producing Lithium Iodide Cleanly through Electrodialysis Metathesis.

Lithium iodide is commonly used in the production of batteries and drugs. Currently, the neutralization method is the primary means of producing lithium iodide. This method involves using hydriodic acid as a raw material, adding lithium carbonate or lithium hydroxide, and obtaining lithium iodide through evaporation and concentration. However, hydriodic acid is chemically unstable. Its preparation can lead to explosive accidents and encountering high temperatures generates toxic iodine vapors. These limitations restrict its industrial production. The study evaluates the impact of membrane stack configuration, operating voltage, and initial concentrations and volume ratios of reactants on the production process. Electrodialysis metathesis, characterized by a simpler process flow, lower energy consumption, and environmental benefits, emerges as an effective technique for electrically driven membrane separation in lithium salt production and purification. Under the specific conditions of a C-C-A-C-A-C membrane stack configuration, operating voltage at 25 V, initial potassium iodide concentration at 0.4 mol/L, initial lithium sulfate concentration at 0.2 mol/L, and a 1:1 volume ratio of product liquid to raw material liquid, the method achieves a lithium iodide purity of 98.9% with a production cost of approximately 0.502 $/kg LiI.

Improvement of the silver staining method for bacterial flagella.

Flagella staining is a common method used in microbial research to identify and mark morphological features of bacteria. We improved the Blendon staining method by adding two steps to the usual procedure, viz. "preparation of a pre-atomized microscope slide" and "stretching flagella in situ". The staining effects were then comparatively studied for this new, improved method on Bacillus subtilis, under four different culture conditions: 1) liquid culture medium, 2) aqueous solution at the bottom of slant medium, 3) solid culture medium adding water for stretching after culture, and 4) semi-solid culture medium adding water for stretching after culture. The results revealed that after the addition of these two steps to the usual procedure, the order of the staining effects for the four culture conditions from best to worst was as follows: semi-solid culture medium > solid culture medium > aqueous solution at the bottom of slant medium > liquid culture medium. Hence, the semi-solid culture medium brought about the best staining effect, with flagella stretching freely and not entangled with each other, while the liquid culture medium had the worst staining, owing to the serious background interference. This improved method is simple, low cost, and worthy of promotion.

Recycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide.

Lithium resources face risks of shortages owing to the rapid development of the lithium industry. This makes the efficient production and recycling of lithium an issue that should be addressed immediately. Lithium bromide is widely used as a water-absorbent material, a humidity regulator, and an absorption refrigerant in the industry. However, there are few studies on the recovery of lithium from lithium bromide after disposal. In this paper, a bipolar membrane electrodialysis (BMED) process is proposed to convert waste lithium bromide into lithium hydroxide, with the generation of valuable hydrobromic acid as a by-product. The effects of the current density, the feed salt concentration, and the initial salt chamber volume on the performance of the BMED process were studied. When the reaction conditions were optimized, it was concluded that an initial salt chamber volume of 200 mL and a salt concentration of 0.3 mol/L provided the maximum benefit. A high current density leads to high energy consumption but with high current efficiency; therefore, the optimum current density was identified as 30 mA/cm2. Under the optimized conditions, the total economic cost of the BMED process was calculated as 2.243 USD·kg-1LiOH. As well as solving the problem of recycling waste lithium bromide, the process also represents a novel production methodology for lithium hydroxide. Given the prices of lithium hydroxide and hydrobromic acid, the process is both environmentally friendly and economical.

Recovery of Acid and Base from Sodium Sulfate Containing Lithium Carbonate Using Bipolar Membrane Electrodialysis.

Lithium carbonate is an important chemical raw material that is widely used in many contexts. The preparation of lithium carbonate by acid roasting is limited due to the large amounts of low-value sodium sulfate waste salts that result. In this research, bipolar membrane electrodialysis (BMED) technology was developed to treat waste sodium sulfate containing lithium carbonate for conversion of low-value sodium sulfate into high-value sulfuric acid and sodium hydroxide. Both can be used as raw materials in upstream processes. In order to verify the feasibility of the method, the effects of the feed salt concentration, current density, flow rate, and volume ratio on the desalination performance were determined. The conversion rate of sodium sulfate was close to 100%. The energy consumption obtained under the best experimental conditions was 1.4 kWh·kg-1. The purity of the obtained sulfuric acid and sodium hydroxide products reached 98.32% and 98.23%, respectively. Calculated under the best process conditions, the total process cost of BMED was estimated to be USD 0.705 kg-1 Na2SO4, which is considered low and provides an indication of the potential economic and environmental benefits of using applying this technology.

Purification of Methylsulfonylmethane from Mixtures Containing Salt by Conventional Electrodialysis.

Methylsulfonylmethane (MSM) is one of the main sources of sulfur for living bodies, but it is hard to obtain as a pure compound. Conventional electrodialysis (CED) is a mature technology that can be used for the separation and purification of biochemical products. In this study, the purification of MSM from mixtures containing salt was performed by CED. The effects of operating conditions such as operation voltage drop, feed MSM concentration, and electrolyte salt concentration on the separation performances were investigated. The results showed that the current efficiency reached 74.0%, and the energy consumption could be 12.3 Wh·L-1. As for the recovery rate and desalination rate, the highest recovery rate could be 97.4%, and the desalination rate was 98.5%. Based on process energy consumption calculation, the total cost of the whole process was estimated at only 2.34 $·t-1. Thus, CED is highly efficient and cost-effective for the separation and purification of MSM.