Photodissociation spectra of single trapped CaOH+ molecular ions.

Molecular ions that are generated by chemical reactions with trapped atomic ions can serve as an accessible testbed for developing molecular quantum technologies. On the other hand, they are also a hindrance to scaling up quantum computers based on atomic ions, as unavoidable reactions with background gases destroy the information carriers. Here, we investigate the single- and two-photon dissociation processes of single CaOH+ molecular ions co-trapped in Ca+ ion crystals using a femtosecond laser system. We report the photodissociation cross section spectra of CaOH+ for single-photon processes at λ = 245-275 nm and for two-photon processes at λ = 500-540 nm. Measurements are interpreted with quantum-chemical calculations, which predict the photodissociation threshold for CaOH+ → Ca+ + OH at 265 nm. This result can serve as a basis for dissociation-based spectroscopy for studying the internal structure of CaOH+. The result also gives a prescription for recycling Ca+ ions in large-scale trapped Ca+ quantum experiments from undesired CaOH+ ions formed in the presence of background water vapor.

Investigation of piezoelectric printing devices for oil-free and on-demand picolitre monodisperse droplet generation.

Picolitre monodisperse droplet printing technology has important applications in biochemistry, such as accounting for quantitative analysis and single-cell analysis, and can be used for parallel high-throughput analysis of biomarkers and chemicals. However, commonly used droplet generation devices require complex control systems or customised microfluidic chips, making them costly and difficult for researchers to operate. Additionally, generating picolitre monodisperse droplets with microfluidic devices necessitates the introduction of an oil phase to block and separate the liquid. This requirement can reduce the throughput of the target droplets and cause cell contamination, hindering the adoption of this technology. By employing a common 1-mm-diameter capillary in the laboratory in combination with a piezoelectric transducer, we have achieved on-demand picolitre droplet printing of less than 100 pL in an oil-free environment. The device was found to be biocompatible with K562 cells. This approach is less costly, offers greater operational freedom, and is easier to integrate with other downstream assay modules or even handheld cell-printing devices. This study holds great potential for application in areas such as single-cell analysis, cell sampling, and pharmaceutical analysis.

Identification and Analysis of Biomarkers Associated with Lipophagy and Therapeutic Agents for COVID-19.

BACKGROUND: Lipids, as a fundamental cell component, play an regulating role in controlling the different cellular biological processes involved in viral infections. A notable feature of coronavirus disease 2019 (COVID-19) is impaired lipid metabolism. The function of lipophagy-related genes in COVID-19 is unknown. The present study aimed to investigate biomarkers and drug targets associated with lipophagy and lipophagy-based therapeutic agents for COVID-19 through bioinformatics analysis. METHODS: Lipophagy-related biomarkers for COVID-19 were identified using machine learning algorithms such as random forest, Support Vector Machine-Recursive Feature Elimination, Generalized Linear Model, and Extreme Gradient Boosting in three COVID-19-associated GEO datasets: scRNA-seq (GSE145926) and bulk RNA-seq (GSE183533 and GSE190496). The cMAP database was searched for potential COVID-19 medications. RESULTS: The lipophagy pathway was downregulated, and the lipid droplet formation pathway was upregulated, resulting in impaired lipid metabolism. Seven lipophagy-related genes, including ACADVL, HYOU1, DAP, AUP1, PRXAB2, LSS, and PLIN2, were used as biomarkers and drug targets for COVID-19. Moreover, lipophagy may play a role in COVID-19 pathogenesis. As prospective drugs for treating COVID-19, seven potential downregulators (phenoxybenzamine, helveticoside, lanatoside C, geldanamycin, loperamide, pioglitazone, and trichostatin A) were discovered. These medication candidates showed remarkable binding energies against the seven biomarkers. CONCLUSIONS: The lipophagy-related genes ACADVL, HYOU1, DAP, AUP1, PRXAB2, LSS, and PLIN2 can be used as biomarkers and drug targets for COVID-19. Seven potential downregulators of these seven biomarkers may have therapeutic effects for treating COVID-19.

Solidification of municipal solid waste incineration fly ash with alkali-activated technology.

Alkali-activation is effective municipal solid waste incineration fly ash (MSWIFA) solidification/stabilization (S/S) technology. Percolation and migration of heavy metals in MSWIFA S/S matrix is a complicated and slow process. Here, several alkali-activated MSWIFA samples are selected to comparatively investigate the long-term leaching behavior and environmental availability of Pb, Zn and Cd when exposed in different erosion environment. Acid environment posed the more serious destroy to MSWIFA S/S matrices. RAC demonstrated that potential risk level of heavy metals is higher in acid rain environment, and Cd, Zn showed the prominent risk. When soaked in acid rain solution, the surface of alkali-activated MSWIFA S/S matrices was cracked seriously and a large number of hardened slurry peeled off. However, more stable structural properties and lower heavy metal leachability can be found in alkali-activated MSWIFA/aluminosilicate. The immobilization efficiency of Pb, Zn and Cd were all above 99.0%. Microstructure and morphology results indicated that there is new phase Friedel's salts generated and much more amorphous substance such as C-(A)-S-H gel with incorporation of aluminosilicate, which all contributed much to the formation of compact and stable microstructure, then significantly facilitated the encapsulation of heavy metal. These findings will provide theoretical basis and new insight for resource utilization and security landfill of MSWIFA.

Silicon-Organic Hybrid Electro-Optic Modulator and Microwave Photonics Signal Processing Applications.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication systems and ultra-wideband microwave photonic systems. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper, we present an SOH-integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH-integrated EOM is measured with 3 dB bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH-integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410° is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

High-performance grating couplers on 220-nm thick silicon by inverse design for perfectly vertical coupling.

Efficient grating couplers (GCs) for perfectly vertical coupling are difficult to realize due to the second-order back reflection. In this study, apodized GCs (AGCs) are presented for achieving perfectly-vertical coupling to 220 nm thick silicon-on-insulator (SOI) waveguides in the C-band. We compare the performance of the AGCs to that of uniform GCs (UGCs) and demonstrate the superiority of the former. The AGCs were obtained through inverse design using gradient-based optimization and were found to effectively suppress back reflection and exhibit better matching to the Gaussian beam profile. The design and measurement results show that AGCs have a 3 dB lower coupling loss than UGCs. We fabricated focusing AGCs by electron beam lithography with a single, 70 nm shallow etch and a minimum feature size of 100 nm, which makes them compatible with CMOS technology. The AGCs achieved a coupling efficiency of -5.86 dB for perfectly vertical coupling. Overall, our results demonstrate the potential of AGCs for achieving high-performance coupling in the C-band on the SOI platform.

Open source board based acoustofluidic transwells for reversible disruption of the blood-brain barrier for therapeutic delivery.

BACKGROUND: Blood-brain barrier (BBB) is a crucial but dynamic structure that functions as a gatekeeper for the central nervous system (CNS). Managing sufficient substances across the BBB is a major challenge, especially in the development of therapeutics for CNS disorders. METHODS: To achieve an efficient, fast and safe strategy for BBB opening, an acoustofluidic transwell (AFT) was developed for reversible disruption of the BBB. The proposed AFT was consisted of a transwell insert where the BBB model was established, and a surface acoustic wave (SAW) transducer realized using open-source electronics based on printed circuit board techniques. RESULTS: In the AFT device, the SAW produced acousto-mechanical stimulations to the BBB model resulting in decreased transendothelial electrical resistance in a dose dependent manner, indicating the disruption of the BBB. Moreover, SAW stimulation enhanced transendothelial permeability to sodium fluorescein and FITC-dextran with various molecular weight in the AFT device. Further study indicated BBB opening was mainly attributed to the apparent stretching of intercellular spaces. An in vivo study using a zebrafish model demonstrated SAW exposure promoted penetration of sodium fluorescein to the CNS. CONCLUSIONS: In summary, AFT effectively disrupts the BBB under the SAW stimulation, which is promising as a new drug delivery methodology for neurodegenerative diseases.

Power-controlled acoustofluidic manipulation of microparticles.

Recently, surface acoustic wave (SAW) based acoustofluidic separation of microparticles and cells has attracted increasing interest due to accuracy and biocompatibility. Precise control of the input power of acoustofluidic devices is essential for generating optimum acoustic radiation force to manipulate microparticles given their various parameters including size, density, compressibility, and moving velocity. In this work, an acoustophoretic system is developed by employing SAW based interdigital electrode devices. Power meters are applied to closely monitor the incident and reflected powers of the SAW device, which are associated with the separation efficiency. There exists a range of input powers to migrate the microparticles to the pressure node due to their random locations when entering the SAW field. Theoretical analysis is performed to predict a proper input power to separate mixtures of polystyrene microspheres, and the end lateral position of microspheres being acoustically separated. The separation efficiency of four sizes of microspheres, including 20 µm, 15 µm, 10 µm, and 5 µm, is calculated and compared with experimental results, which suggest the input power for separating the mixture of these microspheres. The study provides a practical guidance on operating SAW devices for bioparticle separation using the incident power as a control parameter.

An enhanced tilted-angle acoustic tweezer for mechanical phenotyping of cancer cells.

Acoustofluidic devices becomes one of the emerging and versatile tools for many biomedical applications. Most of the previous acoustofluidic devices are used for cells manipulation, and the few devices for cell phenotyping with a limitation in throughput. In this study, an enhanced tilted-angle (ETA) acoustofluidic device is developed and applied for mechanophenotyping of live cells. The ETA Device consists of an interdigital transducer which is positioned along a microfluidic channel. An inclination angle of 5° is introduced between the interdigital transducer and the liquid flow direction. The pressure nodes formed inside the acoustofluidic field in the channel deflect the biological cells from their original course in accordance with their mechanical properties, including volume, compressibility, and density. The threshold power for fully converging the cells to the pressure node is used to calculate the acoustic contrast factor. To demonstrate the ETA device in cell mechanophenotyping, and distinguishing between different cell types, further experimentation is carried out by using A549 (lung cancer cells), MDB-MA-231 (breast cancer cells), and leukocytes. The resulting acoustic contrast factors for the lung and breast cancer cells are different from that of the leukocytes by 27.9% and 21.5%, respectively. These results suggest this methodology can successfully distinguish and phenotype different cell types based on the acoustic contrast factor.

Facile surface treatment strategy to generate dense lysozyme layer on ultra-high molecular weight polyethylene enabling inhibition of bacterial biofilm formation.

Medical plastics such as those found in endotracheal tubes are widely used in intensive care units for the treatment of critically ill patients. Although commonplace in hospital environment, these catheters are at a high risk of bacterial contamination and have been found responsible for numerous health-care-associated infections. Antimicrobial coatings that can prevent harmful bacterial growth are required to reduce the occurrence of such infections. In this study, we introduce a facile surface treatment strategy that could form antimicrobial coatings on the surface of average medical plastics. The strategy involves treatment of activated surfaces with lysozyme, a natural antimicrobial enzyme presenting in human lacrimal gland secretions which is widely used for wound healing. Using ultra-high molecular weight polyethylene (UHMWPE) as the representative surface, oxygen/argon plasma treatment for 3 min led to the increase of surface roughness and the generation of negatively charged groups, with the zeta potential measured as -94.5 mV at pH 7. The activated surface could accommodate lysozyme with a density of up to 0.3 nmol/cm2 through electrostatic interaction. Antimicrobial activity of the resulting surface (UHMWPE@Lyz) was characterized with Escherichia coli and Pseudomonas sp. strains, and the treated surface significantly inhibited the bacterial colonization and the formation of biofilm compared to the untreated UHMWPE. This method of constructing an effective lysozyme-based antimicrobial coating is a generally applicable, simple and fast process for surface treatment with no adverse solvent and wastes involved.

Multiband Signal Receiver by Using an Optical Bandpass Filter Integrated with a Photodetector on a Chip.

Photonic integration brings the promise of significant cost, power and space savings and propels the real applications of microwave photonic technology. In this paper, a multiband radio frequency (RF) signal simultaneous receiver using an optical bandpass filter (OBPF) integrated with a photodetector (PD) on a chip is proposed, which was experimentally demonstrated. The OBPF was composed of ring-assisted Mach-Zehnder interferometer with a periodical bandpass response featuring a box-like spectral shape. The OBPF was connected to a PD and then integrated onto a single silicon photonic chip. Phase-modulated multiband RF signals transmitted from different locations were inputted into the OBPF, by which one RF sideband was filtered out and the phase modulation to intensity modulation conversion was realized. The single sideband with carrier signals were then simultaneously detected by the PD. A proof-of-concept experiment with the silicon photonic integrated chip was implemented to simultaneously receive four channels of 8 GHz, 12 GHz, 14 GHz and 18 GHz in the X- and Ku-bands. The performance of the integrated microwave photonic multiband receiver-including the receiving sensitivity, the spurious free dynamic range, the gain and the noise figure across the whole operation frequency band-was characterized in detail.

Acoustically accelerated neural differentiation of human embryonic stem cells.

Human embryonic stem cells (hESCs) and their derived products offer great promise for targeted therapies and drug screening, however, the hESC differentiation process of mature neurons is a lengthy process. To accelerate the neuron production, an acoustic stimulator producing surface acoustic waves (SAWs) is proposed and realized by clamping a flexible printed circuit board (PCB) directly onto a piezoelectric substrate. Neural differentiation of the hESCs is greatly accelerated after application of the acoustic stimulations. Acceleration mechanisms for neural differentiation have been explored by bulk RNA sequencing, quantitative polymerase chain reaction (qPCR) and immunostaining. The RNA sequencing results show changes of extracellular matrix-related and physiological activity-related gene expression in the low or medium SAW dose group and the high SAW dose group, respectively. The neural progenitor cell markers, including Pax6, Sox1, Sox2, Sox10 and Nkx2-1, are less expressed in the SAW dose groups compared with the control group by the qPCR. Other genes including Alk, Cenpf, Pcdh17, and Actn3 are also found to be regulated by the acoustic stimulation. Moreover, the immunostaining confirmed that more mature neuron marker Tuj1-positive cells, while less stem cell marker Sox2-positive cells, are presented in the SAW dose groups. These results indicate that the SAW stimulation accelerated neural differentiation process. The acoustic stimulator fabricated by using the PCB is a promising tool in regulation of stem cell differentiation process applied in cell therapy. STATEMENT OF SIGNIFICANCE: Human embryonic stem cells (hESC) are used for investigating the complex mechanisms involved in the development of specialized biological cells and organs. Different types of hESCs derived cell products can be used for cell therapy procedures aiming to regenerate functional tissues in patients who suffer from various degenerative diseases. Accelerating the hESCs' differentiation process can considerably benefit the clinical utilization of these cells. This study develops a highly effective acoustic stimulator working at ∼20 MHz to investigate what roles do acousto-mechanical stimuli play in the differentiation of hESCs. Our results show that acoustic dose alters the extracellular matrix and physiological activity-related gene expression, which indicates that the acoustic stimulation is an important tool for regulating the stem cells' differentiation processes in cell therapy.

Optical Waveguide Sensors for Measuring Human Temperature and Humidity with Gel Polymer Electrolytes.

In this work, multimodal responsive optical waveguide sensors using a stable cross-linking gel polymer electrolyte are successfully designed and fabricated by bottom metal-printing technology. Temperature and humidity sensing characterization based on the polymer electrolyte is simulated and analyzed. The multimodal responsive properties of the photonic chip are defined based on the analysis of ion relaxation dynamics: optical phase variable to monitor temperature and optical attenuation variable to detect humidity. In the supervising temperature (36.0-38.0 °C) and relative humidity (45-65%) range, the temperature and humidity sensitivities of the device are measured as 0.5π rad/°C and 1.14 dB/% RH, respectively. The fast-response time for both temperature and humidity of the multifunctional sensor can be obtained as 4.21 ms and 1.32 s, respectively. These findings provide a feasible scheme for the design and application of temperature and humidity sensors in potential medical treatment. From gel polymer electrolytes to multimode monitoring applications, the application exploration of high stability and ultrafast response multimode waveguide sensors is gradually being carried out. This study has great significance for the comprehensive monitoring of sophisticated human physical signs by multimodal responsive waveguide sensors.

Correction: Development and characterisation of acoustofluidic devices using detachable electrodes made from PCB.

Correction for 'Development and characterisation of acoustofluidic devices using detachable electrodes made from PCB' by Roman Mikhaylov et al., Lab Chip, 2020, 20, 1807-1814, DOI: 10.1039/C9LC01192G.

Thin film Gallium nitride (GaN) based acoustofluidic Tweezer: Modelling and microparticle manipulation.

Gallium nitride (GaN) is a compound semiconductor which shows advantages in new functionalities and applications due to its piezoelectric, optoelectronic, and piezo-resistive properties. This study develops a thin film GaN-based acoustic tweezer (GaNAT) using surface acoustic waves (SAWs) and demonstrates its acoustofluidic ability to pattern and manipulate microparticles. Although the piezoelectric performance of the GaNAT is compromised compared with conventional lithium niobate-based SAW devices, the inherited properties of GaN allow higher input powers and superior thermal stability. This study shows for the first time that thin film GaN is suitable for the fabrication of the acoustofluidic devices to manipulate microparticles with excellent performance. Numerical modelling of the acoustic pressure fields and the trajectories of mixtures of microparticles driven by the GaNAT was performed and the results were verified from the experimental studies using samples of polystyrene microspheres. The work has proved the robustness of thin film GaN as a candidate material to develop high-power acoustic tweezers, with the potential of monolithical integration with electronics to offer diverse microsystem applications.

Development and characterisation of acoustofluidic devices using detachable electrodes made from PCB.

Acoustofluidics has been increasingly applied in biology, medicine and chemistry due to its versatility in manipulating fluids, cells and nano-/micro-particles. In this paper, we develop a novel and simple technology to fabricate a surface acoustic wave (SAW)-based acoustofluidic device by clamping electrodes made using a printed circuit board (PCB) with a piezoelectric substrate. The PCB-based SAW (PCB-SAW) device is systematically characterised and benchmarked with a SAW device made using the conventional photolithography process with the same specifications. Microparticle manipulations such as streaming in droplets and patterning in microchannels were demonstrated in the PCB-SAW device. In addition, the PCB-SAW device was applied as an acoustic tweezer to pattern lung cancer cells to form three or four traces inside the microchannel in a controllable manner. Cell viability of ∼97% was achieved after acoustic manipulation using the PCB-SAW device, which proved its ability as a suitable tool for acoustophoretic applications.

Alkali Activation of Copper and Nickel Slag Composite Cementitious Materials.

Alkali-activated copper and nickel slag cementitious materials (ACNCMs) are composite cementitious materials with CNS (copper and nickel slag) as the main materials and GGBFS (ground-granulated blast-furnace slag) as a mineral admixture. In this paper, the activity indexes of CNS with different grinding times were studied using CNS to replace a portion of cement. NaOH, Na2SO4, and Na2SiO3 activators were used to study the alkaline solution of the CNS glass phase. The effects of the fineness of CNS and the type of activator on the hydration of ACNCMs were investigated via physical/mechanical grinding and chemical activation. The hydration products of ACNCMs were analyzed via XRD, SEM, FT-IR, TG, and MIP. The results of the study revealed that the activity indexes of CNS ground with different grinding times (10, 30 and 50 min) were 0.662, 0.689, and 0.703, respectively. When Na2SiO3 was used as the activator, the glass phase dissolved the most Si4+, Al3+, and Ca2+, and the respective concentrations in the solution were found to be 2419, 39.55, and 3.38 mg/L. Additionally, the hydration products of ACNCMs were found to have a 28-day compressive strength of up to 84 MPa.

Polymer-Based Device Fabrication and Applications Using Direct Laser Writing Technology.

Polymer materials exhibit unique properties in the fabrication of optical waveguide devices, electromagnetic devices, and bio-devices. Direct laser writing (DLW) technology is widely used for micro-structure fabrication due to its high processing precision, low cost, and no need for mask exposure. This paper reviews the latest research progresses of polymer-based micro/nano-devices fabricated using the DLW technique as well as their applications. In order to realize various device structures and functions, different manufacture parameters of DLW systems are adopted, which are also investigated in this work. The flexible use of the DLW process in various polymer-based microstructures, including optical, electronic, magnetic, and biomedical devices are reviewed together with their applications. In addition, polymer materials which are developed with unique properties for the use of DLW technology are also discussed.

Cascaded-Microrings Biosensors Fabricated on a Polymer Platform.

Polymer-based single-microring biosensors usually have a small free spectral range (FSR) that hampers the tracing of the spectrum shifting in the measurement. A cascade of two microring resonators based on the Vernier effect, is applied in this article in order to make up for this defect. A small FSR difference between the reference microring and the sensing microring is designed, in order to superpose the periodic envelope signal onto the constituent peaks, which makes it possible to continuously track the spectrum of the sensor. The optical polymer material, Ormocore, which has a large transparent window, is used in the fabrication. The biosensor is fabricated by using an UV-based soft imprint technique, which is considered to be cost-effective and suitable for mass production. By optimizing the volume ratio of Ormocore and the maT thinner, the device can be fabricated almost without a residual layer. The device works at a wavelength of 840 nm, where water absorption loss is much lower than at the infrared wavelengths. A two-step fitting method, including single-peak fitting and whole-envelope fitting, is applied in order to trace the spectral shift accurately. Finally, the two-cascaded-microrings biosensor is characterized, and the obtained FSR is 4.6 nm, which is 16 times larger than the FSR of the single microring biosensor demonstrated in our previous work. Moreover, the sensitivity can also be amplified by 16-fold, thanks to the Vernier effect.

Tilted Fiber Bragg Grating Sensor Using Chemical Plating of a Palladium Membrane for the Detection of Hydrogen Leakage.

A tilted fiber Bragg grating (TFBG) hydrogen sensor coated with a palladium (Pd) membrane by the electroless plating method is proposed in this paper. A uniform layer of Pd metal is fabricated in aqueous solutions by the chemical coating method, which is used as the sensitive element to detect the change of the surrounding refractive index (SRI) caused by hydrogen absorption. The change in SRI causes an unsynchronized change of the cladding modes and the Bragg peak in the TFBG transmission spectrum, thereby eliminating the cross-sensitivity due to membrane expansion and is able to simultaneously monitor the presence of cracks in the pipe, as well as the hydrogen leakage. By subtracting the wavelength shift caused by fiber expansion, the change of SRI, i.e., the information from the H2 level, can be separately obtained. The drifted wavelength is measured for the H2 concentration below the hydrogen explosion limit between 1% and 4%. The chemical-based coating has the advantages of a low cost, a simple operation, and being suitable for coating on long fiber structures. The proposed sensor is able to detect the H2 signal in 5 min at a 1% H2 concentration. The proposed sensor is proved to be able to monitor the hydrogen level without the cross-sensitivity of temperature variation and expansion strains, so could be a good candidate for security applications in industry.