Magnetic Field Influence on the Microwave Characteristics of Composite Samples Based on Polycrystalline Y-Type Hexaferrite.

Here, we report results on the magnetic and microwave properties of polycrystalline Y-type hexaferrite synthesized by sol-gel auto-combustion and acting as a filler in a composite microwave-absorbing material. The reflection losses in the 1-20 GHz range of the Y-type hexaferrite powder dispersed homogeneously in a polymer matrix of silicon rubber were investigated in the absence and in the presence of a magnetic field. A permanent magnet was used with a strength of 1.4 T, with the magnetic force lines oriented perpendicularly to the direction of the electromagnetic wave propagation. In the case of using an external magnetic field, an extraordinary result was observed. The microwave reflection losses reached a maximum value of 35.4 dB at 5.6 GHz in the Ku-band without a magnetic field and a maximum value of 21.4 dB at 8.2 GHz with the external magnetic field applied. The sensitivity of the microwave properties of the composite material to the external magnetic field was manifested by the decrease of the reflected wave attenuation. At a fixed thickness, tm, of the composite, the attenuation peak frequency can be adjusted to a certain value either by changing the filling density or by applying an external magnetic field.

High Critical Current Density in the Textured Nanofiber Structure in Multifilament MgB2 Wires Made by the Powder-In-Tube (PIT) Technique.

We show that the structure of multifilament MgB2 wires made by the powder-in-tube (PIT) method can be texturized by annealing the structure under high isostatic pressure. Our results show that we obtained continuous fibers with a uniform diameter of 250 nm in all 36 filaments, a small grain size of approximately 50 nm and a high density of the superconducting material. These results contribute to a significant improvement in the critical current density in high magnetic fields, e.g., 100 A/mm2 at 14 T and 4.2 K.

Effect of Heat Treatments under High Isostatic Pressure on the Transport Critical Current Density at 4.2 K and 20 K in Doped and Undoped MgB2 Wires.

Annealing undoped MgB2 wires under high isostatic pressure (HIP) increases transport critical current density (Jtc) by 10% at 4.2 K in range magnetic fields from 4 T to 12 T and significantly increases Jtc by 25% in range magnetic fields from 2 T to 4 T and does not increase Jtc above 4 T at 20 K. Further research shows that a large amount of 10% SiC admixture and thermal treatment under a high isostatic pressure of 1 GPa significantly increases the Jtc by 40% at 4.2 K in magnetic fields above 6 T and reduces Jtc by one order at 20 K in MgB2 wires. Additionally, our research showed that heat treatment under high isostatic pressure is more evident in wires with smaller diameters, as it greatly increases the density of MgB2 material and the number of connections between grains compared to MgB2 wires with larger diameters, but only during the Mg solid-state reaction. In addition, our study indicates that smaller wire diameters and high isostatic pressure do not lead to a higher density of MgB2 material and more connections between grains during the liquid-state Mg reaction.

Influence of Amorphous Boron Grain Size, High Isostatic Pressure, Annealing Temperature, and Filling Density of Unreacted Material on Structure, Critical Parameters, N-Value, and Engineering Critical Current Density in Mgb2 Wires.

Our results show that a lower density of unreacted Mg + B material during an Mg solid-state synthesis reaction leads to a significant reduction in the quantity of the superconducting phase and lowers the homogeneity of the superconducting material. It also significantly reduces the irreversible magnetic field (Birr), critical temperature (Tc), upper magnetic field (Bc2), engineered critical current density (Jec), and n-value, despite high isostatic pressure (HIP) treatment and the use of nanoboron in the sample. Our measurements show that samples with large boron grains with an 8% higher density of unreacted Mg + B material allow better critical parameters to be achieved. Studies have shown that the density of unreacted material has little effect on Birr, Tc, Bc2, Jec, and the n-value for an Mg liquid-state synthesis reaction. The results show that the critical parameters during an Mg liquid-state synthesis reaction depend mainly on grain size. Nanoboron grains allow for the highest Birr, Tc, Bc2, Jec, and n-values. Scanning electron microscopy (SEM) images taken from the longitudinal sections of the wires show that the samples annealed under low isostatic pressure have a highly heterogeneous structure. High isostatic pressure heat treatment greatly improves the homogeneity of MgB2.

Data supporting the results of the characterization of the phases and structures appearing during the synthesis process of Ba0.5Sr1.5Zn2-xNixFe12O22 by auto-combustion.

The data presented has to do with identifying the various phases arising during the synthesis of the Y-type hexaferrite series Ba0.5Sr1.5Zn2-xNixFe12O22 by auto-combustion that we deem important for their microstructural and magnetic properties. The data and the related analyses support the research paper "Ni-substitution effect on the properties of Ba0.5Sr1.5Zn2-xNixFe12O22 powders" [1]. Thus, the parameters are presented of the phases appearing after auto-combustion and after the initial annealing at 800 °C, namely, crystal cell and crystallite size. Also, additional data are provided obtained by EDS concerning the Ba:Sr:Zn:Ni:Fe ratio in Ba0.5Sr1.5Zn2-xNixFe12O22 (x = 0.8, 1, 1.5) samples synthesized at 1170 °C for 10 h. The data can be used as a reference in establishing how the phases distinguished during the initial process of auto-combustion affect the Ba0.5Sr1.5Zn2-xNixFe12O22 powders, which are candidates for room-temperature multiferroic materials. The data have not been published previously and are made available to permit critical or further analyses.

Observation of superconductivity in the intermetallic compound ß-IrSn4.

Low-temperature dc-magnetization, ac electrical resistivity and specific heat measurements were performed on single crystals of the intermetallic compound ß-IrSn4. The compound crystallizes in the tetragonal MoSn4-type structure (space group I41/acd) and exhibits superconductivity below Tc = 0.9 ± 0.05 K. Further, the magnitude of the ratios ΔCp/(γnkBTc) = 1.29, 2Δ/(kBTc) = 3.55 and of the electron-phonon coupling λ[overline](e-ph) = 0.5 imply that superconductivity in ß-IrSn4 can be ascribed to a s-wave weak coupling regime. We determined crucial thermodynamic characteristics of the superconducting state. It turned out that depending on the assumption of either a spherical or non-spherical Fermi surface, the superconductivity can be ascribed to either a type-I and type-II/1 or type-II in clean limit, respectively. However, the behavior of the upper critical field and the anisotropic crystalline structure of the studied compound provide strong support to the type-II superconductivity. In the normal state the resistivity exhibits a prominent quadratic temperature dependence, which together with a large Kadowaki-Woods ratio and with the enhanced effective mass indicate that the electrons in ß-IrSn4 are strongly correlated.