A selective and sensitive fluorescent probe for bilirubin in human serum based on europium(III) post-functionalized Zr(IV)-Based MOFs.

In the present study, a kind of Eu(III) post-functionalized Zr(IV)-based metal-organic framework (UiO-66(COOH)2, Zr-MOF: Eu3+) was synthesized and utilized as an independently luminescent probe for sensing bilirubin (BR) in human serum, a biomarker of jaundice hepatitis. It can be served as a turn-off fluorescent switch for BR because its red emission from Eu3+ can be easily quenched by BR through a fluorescent resonant energy transfer (FRET) process between BR and its ligands, and as a result, BR is recognized successfully. Particularly, Zr-MOF: Eu3+ has shown many appealing properties, such as high sensitivity, quick response (less than 1 min), broad response window (0-15 µM), and excellent selectivity. Most importantly, a kind of portable test paper based on Zr-MOF: Eu3+ probe has been developed for directly assessing the level of BR in real human serum and further diagnosing bilirubin-related diseases via visually observing the luminescent color variation.

[Comparison of the shear bond strength by using nano silica sol to zirconia basement and veneer porcelain].

PURPOSE: To investigate the feasibility of using sol gel technique to produce thin layer nano silicon dioxide on zirconia ceramic surface and the effect of improving shear bond strength between zirconia and veneer porcelain. METHODS: The presintered zirconia specimen was cut into a rectangle block piece (15 mm×10 mm×2.5 mm), a total of 40 pieces were obtained and divided into 4 groups, each group had 10 pieces. Four different treatments were used in each group respectively. Pieces in group A (control group) were only sintered at 1450°C to crystallization; pieces in group B underwent 30% nano silica sol infiltration first and then were sintered at 1450°C to crystallization; piece in group C underwent crystallization first at 1450°C, then 30% nano silica sol infiltration and were sintered at 1450°C again; pieces in group D was coated by nano silica sol and then sintered at 1450°C to crystallization; ten rectangle block pieces (12 mm×8 mm×2 mm) in group E were made. Cylinder veneers 5 mm in diameter and 4 mm in height were produced in each group and the shear bond strength was tested. Data were statistically analyzed by SPSS 19.0 software package. RESULTS: The shear bond strength of the 5 group specimens were: (28.12±2.95) MPa in group A, (31.09±3.94) MPa in group B, (25.60±2.45) MPa in group C, (31.75±4.90) MPa in group D, (28.67±3.95) MPa in group E, respectively. Significant differences existed between the 5 groups, and group C had significant difference compared with group B and D. CONCLUSIONS：① Use of nano silicon sol gel on presintered zirconia surface to make thin layer of nano silicon dioxide can improve the shear bond strength between zirconia and veneer; ②Using nano silicon sol gel on crystallization zirconia surface to make thin layer of nano silicon dioxide will decrease the shear bond strength between zirconia and veneer; ③ Zirconia veneer bilayer ceramic has the same shear bond strength with porcelain fused to Ni Cr alloy; ④Use of sol gel technique to produce thin layer nano silicon dioxide on zirconia ceramic surface is feasible and can improve shear bond strength between zirconia and veneer porcelain.

Effect of Evodiamine on CYP Enzymes in Rats by a Cocktail Method.

The aim of this study was to assess the influence of evodiamine on the activities of the drug-metabolizing enzymes cytochrome P450 (CYP) 1A2, CYP2C9, CYP2C19, CYP2D6 and CYP3A4 in rats. The activities of CYP1A2, CYP2C9, CYP2C19, CYP2D6 and CYP3A4 were measured using specific probe drugs. After pretreatment for 1 week with evodiamine or physiological saline (control group) by oral administration, probe drugs phenacetin (5.0 mg/kg; CYP1A2 activity), tolbutamide (1.0 mg/kg; CYP2C9 activity), omeprazole (10 mg/kg; CYP2C19 activity), metoprolol (20 mg/kg; CYP2D6 activity) and midazolam (10 mg/kg; CYP3A4 activity) were administered to rats by oral administration. The blood was then collected at different times for ultra-performance liquid chromatography-tandem mass spectrometry analysis. The data showed that evodiamine exhibits an inhibitory effect on CYP1A2, CYP2C9 and CYP2D6 by increasing t(1/2), Cmax and AUC(0-∞), and decreasing CL/F compared with those of the control group. However, no significant changes in CYP2C19 and CYP3A4 activities were observed. In conclusion, the results indicated that evodiamine could inhibit CYP1A2, CYP2C9 and CYP2D6, which may affect the disposition of medicines primarily dependent on these pathways. Our work may be the basis of related herb-drug interactions in the clinic.

[Influence of MgO and TiO2 on mechanical properties of zirconia toughened alumina ceramics formed by gel-casting technique].

OBJECTIVE: The objective of this study is to investigate the influence of mechanical properties and sintering performance by adding 5% weight percentage aids to nano-compound zirconia toughened alumina (ZTA) ceramics. METHODS: Micrometer Al2O3 and nanometer ZrO2 (quality ratio 4:1) were used to get 55% volume percentage slurry. Magnesium oxide and titanium oxide were taken as aids which were 5% weight percentage of the Al2O3 and ZrO2 powder. Five groups (number 0, 1, 2, 3, 4 group) were divided according to different proportion of aids. After gel-casting, the porcelain pieces were sintered at 1150, 1200, 1300, 1400, 1450, 1500, 1600 degrees C for 2 hours. Static three-point flexure strength, line shrinkage, relative density were measured and scanning electron microscopy (SEM) was used to observe section. RESULTS: Number 1 (MgO 1%, TiO2 4%) group had the highest bending strength. It was (401.78+/-19.50) MPa after sintering at 1600 degrees C for 2 hours and was higher than 0 group (380.64+/-44.50) MPa. Bending strength became lower than 0 group when MgO was more than 2% or more than that weight percentage of ZTA powder. When MgO content was higher than 2% or more than that weight percentage, there was no difference in relative density raising rate between each sintering assistants groups. When the sintering temperature was higher than 1200 degrees C, all groups showed obvious line-shrinkage and the groups which contained sintering assistants were all was higher than 0 group. CONCLUSION: Adding MgO and TiO2 aids from 1% to 4% weight percentage of ZTA will promote fritting and increase ZTA nano-compound ceramics mechanical properties. Adding 2% MgO aids or more than that weight percent will has no obvious help to increase the relative density raising rate of ZTA nano-compound ceramics and will degrade the mechanical properties of ZTA nano-compound ceramics.

[Effects of fluid shear stress on apoptosis of osteoblasts and expression of bcl-2,Bax and caspase-3].

PURPOSE: The aim of the present investigation is to evaluate the effects of fluid shear stress on the cells of osteoblasts and to determine the mechanisms involved. METHODS: The fluid shear stress with a magnitude of 0 (control group), 0.6, 1.0, 2.0, 3.0, 4.0, 5.0 Pa was exerted on the third passage of osteoblasts for 1 hour,and incubation in static condition for 24 hours. The cell apoptotic index was tested by the terminal transferase dUTP nick end-labeling(TUNEL) method. The expression of bcl-2 ,Bax and caspase-3 were detected by immunohistochemical method. Statistical analysis was performed using SPSS11.5 software package for one-way ANOVA. RESULTS: The apoptosis of osteoblasts and the expression of bcl-2, Caspase-3 were not affected significantly by the fluid shear stress with a magnitude from 0 to 2.0 Pa(P>0.05) . But in the 3.0,4.0 and 5.0 Pa groups, the number of apoptotic cells and the expression of caspase-3 increased while the expression of bcl-2 decreased(P<0.05).There was no significant difference in expression of Bax in all groups. CONCLUSIONS: The physiological fluid shear stress does not affect apoptosis of osteoblasts. However,the fluid shear stress of over-magnitude may lead to the decrease the expression of bcl-2,which results in activation of caspase-3 and apoptosis of osteoblasts. Supported by Research Grant from Zhejiang Provincial Education Committee(Grant No.20061823).

[Study on the surface roughness of three dental alloys soaked in artificial saliva].

PURPOSE: The aim of this study was to investigate the corrosion behavior of three metal materials for dental use (Co-Cr alloy, Ni-Cr alloy, titanium) by measurement of their surface roughness after soaked in artificial saliva with two different pH values. METHODS: Standard samples were casted respectively from 3 different alloys and grided into the same roughness .Then the samples were exposed to artificial saliva with two different pH values. After three months,the surface roughness of the samples was tested, and the microstructure of surfaces was studied by metalloscope. The data were analyzed with SPSS11.0 software package for one-way ANOVA and t test. RESULTS: There was significant difference in surface roughness of three alloys after exposed to artificial saliva with pH5.6. The surface roughness values of three alloys were listed as follows: Ni-Cr alloy>Co-Cr alloy >titanium(P<0.01). When exposed to artificial saliva with pH7.0, Ni-Cr alloy was found rougher than Co-Cr alloy and titanium(P<0.01), while there was no significant difference in roughness between Co-Cr alloy and titanium(P>0.05).Ni-Cr alloy and Co-Cr alloy soaked in artificial saliva with pH5.6 were found rougher than the same material in artificial saliva with pH7.0(P<0.01).The microstructure of the samples' surface verified the results. CONCLUSION: Titanium was stable not only in neutral environment but also in acid environment. The corrosion resistance of Co-Cr alloy and Ni-Cr alloy was superior in neutral environment than in acid environment. The corrosion resistance of the three alloys was: Titanium >Co-Cr alloy >Ni-Cr alloy.