Quantitative evaluation of vertical control in orthodontic camouflage treatment for skeletal class II with hyperdivergent facial type.

BACKGROUND: In this study, we sought to quantify the influence of vertical control assisted by a temporary anchorage device (TAD) on orthodontic treatment efficacy for skeletal class II patients with a hyperdivergent facial type and probe into the critical factors of profile improvement. METHODS: A total of 36 adult patients with skeletal class II and a hyperdivergent facial type were included in this retrospective case-control study. To exclude the effect of sagittal anchorage reinforcement, the patients were divided into two groups: a maxillary maximum anchorage (MMA) group (N = 17), in which TADs were only used to help with anterior tooth retraction, and the MMA with vertical control (MMA + VC) group (N = 19), for which TADs were also used to intrude the maxillary molars and incisors. The treatment outcome was evaluated using dental, skeletal, and soft-tissue-related parameters via a cephalometric analysis and cast superimposition. RESULTS: A significant decrease in ANB (P < 0.05 for both groups), the retraction and uprighting of the maxillary and mandibular incisors, and the retraction of protruded upper and lower lips were observed in both groups. Moreover, a significant intrusion of the maxillary molars was observed via the cephalometric analysis (- 1.56 ± 1.52 mm, P < 0.05) and cast superimposition (- 2.25 ± 1.03 mm, P < 0.05) of the MMA + VC group but not the MMA group, which resulted in a remarkable decrease in the mandibular plane angle (- 1.82 ± 1.38°, P < 0.05). The Z angle (15.25 ± 5.30°, P < 0.05) and Chin thickness (- 0.97 ± 0.45°, P < 0.05) also improved dramatically in the MMA + VC group, indicating a better profile and a relaxed mentalis. Multivariate regression showed that the improvement in the soft tissue was closely related to the counterclockwise rotation of the mandible plane (P < 0.05). CONCLUSIONS: TAD-assisted vertical control can achieve intrusion of approximately 2 mm for the upper first molars and induce mandibular counterclockwise rotation of approximately 1.8°. Moreover, it is especially important for patients without sufficient retraction of the upper incisors or a satisfactory chin shape.

Biomechanical effects of clear aligner with different shape design at extraction space area during anterior teeth retraction.

OBJECTIVE: This study aimed to investigate the biomechanical effects of clear aligner (CA) with different shape designs at extraction space (CAES) area during space closing. MATERIALS AND METHODS: A finite-element method (FEM) model of mandibular dentition, periodontal ligaments, attachments, and corresponding CA was established. The connecting rod design of CAES was modelled for the control group. Eight test groups with different heights of CAES from -4 mm to +4 mm were designed. Tooth displacement tendencies were calculated. The maximum principal stress in PDLs, teeth, and CAs was analysed. Both global coordinate system and local coordinate system were also used to evaluate individual tooth movements. RESULTS: Across all groups, stresses concentrated on the lingual outer surface of CAESs. For the lowered CAES groups, both the stress value and the stress distribution area at CAESs were increased. The lowered CAES groups showed reduced movement in anterior teeth and less tipping tendency of the canines. CONCLUSION: The shape of CAES has a biomechanical impact on anterior teeth movement and should be considered in aligner design. The results suggest that increasing the height of CAES can enhance anterior teeth retraction, while lowered CAES may facilitate controlled root movement. Changes in the shape of CAES represent a potential direction for biomechanical improvement of clear aligner in extraction cases and are worth exploring.

Matrix Metalloproteinase-Responsive Hydrogel with On-Demand Release of Phosphatidylserine Promotes Bone Regeneration Through Immunomodulation.

Inflammation-responsive hydrogels loaded with therapeutic factors are effective biomaterials for bone tissue engineering and regenerative medicine. In this study, a matrix metalloproteinase (MMP)-responsive injectable hydrogel is constructed by integrating an MMP-cleavable peptide (pp) into a covalent tetra-armed poly-(ethylene glycol) (PEG) network for precise drug release upon inflammation stimulation. To establish a pro-regenerative environment, phosphatidylserine (PS) is encapsulated into a scaffold to form the PEG-pp-PS network, which could be triggered by MMP to release a large amount of PS during the early stage of inflammation and retain drug release persistently until the later stage of bone repair. The hydrogel is found to be mechanically and biologically adaptable to the complex bone defect area. In vivo and in vitro studies further demonstrated the ability of PEG-pp-PS to transform macrophages into the anti-inflammatory M2 phenotype and promote osteogenic differentiation, thus, resulting in new bone regeneration. Therefore, this study provides a facile, safe, and promising cell-free strategy on simultaneous immunoregulation and osteoinduction in bone engineering.

[Soft and hard tissue changes of hyperdivergent class â ¡ patients before and after orthodontic extraction treatment].

OBJECTIVE: To investigate the hard and soft tissue changing trend and contributing factors of skeletal class Ⅱ hyperdivergent patients before and after orthodontic camouflage treatment by analyzing the cephalogram and the three dimensional (3D) facial scan data. METHODS: Eighteen skeletal class Ⅱ hyperdivergent adult female patients who finished camouflage orthodontic treatment were selected. Skeletal and dental measurements were carried out with the cephalometric analysis before and after the treatment. 3D facial data before and after orthodontic treatment were acquired and the anatomical landmarks were set after the repositioning and superimposition process. Hard tissue measurement included 17 mea-surement indicators (sella-nasion-subspinale angle, sella-nasion-supramental angle, subspinale-nasion-supramental angle, facial angle, angle of convexity, Frankfort horizontal plane-mandibular plane angle (FH-MP), Y axis angle, sella-nasion plane-mandibular plane angle (MP-SN), pogonion-nasion-supramental distance, upper incisor-nasion-subspinale distance, upper incisor to sella-nasion, lower incisor-nasion-supramental distance, lower incisor-nasion-supramental angle, upper incisor to lower incisor, upper incisor to sella-nasion, lower incisor-mandibular plane angle, and Z angle), and the changes before and after treatment were measured for 11 of them. Twenty soft tissue landmarks (left/right cheekbone, left/right chelion, left/right crista philtra, soft tissue gnathion, left/right gonion, glabella, labrale infe-rius, labrale superius, soft tissue menton, left/right mid-mandibular border, soft tissue pogonion, stomion superius, sublabial, subnasale, and supralabial) and 9 soft tissue indicators (lower lip height, facial convexity, lower vermilion height, mandibular contour, nasolabial angle, philtral length, philtral width, upper lip height, and upper vermilion height) were measured and recorded for treatment changes. Linear-regression analysis and correlation analysis were carried out for analyzing the relationship between hard and soft tissue changes before and after the treatment. RESULTS: Significant differences were noticed for 18 out of the 20 cephalometric measurements and facial measurements before and after the treatment (P < 0.05), which mainly represented the sagittal retraction of lip area after the treatment. Significant vertical displacements were revealed for soft tissue menton after treatment [(1.88±2.61) mm, P < 0.05]. Significant sagittal displacements were revealed for left/right cheilion [(-2.95±1.9) mm, (-2.90±1.92) mm], labrale inferius[(-4.94±1.95) mm], labrale superius[(-3.25±1.44) mm], sublabial [(-3.10±3.5) mm], and subnasale [(-1.23±1.06) mm] after treatment (P < 0.05). An average of 4.10°±2.57° increasement was noticed for Z angle after treatment. High correlation (r>0.7) was noticed for the displacement of menton after treatment with FH-MP, with the rate of -0.183 :1, and MP-SN, with the rate of -0.157 :1. Moderate correlations (0.7≥r>0.4) were noticed for the other measurements with correlations (P < 0.05). CONCLUSION: A certain extent of facial improvements could be achieved with orthodontic camouflage treatment for skeletal class Ⅱ hyperdivergent patients, which were mostly represented by the improvement of sagittal relationship of nose, lips, and chin. Certain correlations were noticed for the hard and soft tissue changes.

Force-induced Caspase-1-dependent pyroptosis regulates orthodontic tooth movement.

Pyroptosis, an inflammatory caspase-dependent programmed cell death, plays a vital role in maintaining tissue homeostasis and activating inflammatory responses. Orthodontic tooth movement (OTM) is an aseptic force-induced inflammatory bone remodeling process mediated by the activation of periodontal ligament (PDL) progenitor cells. However, whether and how force induces PDL progenitor cell pyroptosis, thereby influencing OTM and alveolar bone remodeling remains unknown. In this study, we found that mechanical force induced the expression of pyroptosis-related markers in rat OTM and alveolar bone remodeling process. Blocking or enhancing pyroptosis level could suppress or promote OTM and alveolar bone remodeling respectively. Using Caspase-1-/- mice, we further demonstrated that the functional role of the force-induced pyroptosis in PDL progenitor cells depended on Caspase-1. Moreover, mechanical force could also induce pyroptosis in human ex-vivo force-treated PDL progenitor cells and in compressive force-loaded PDL progenitor cells in vitro, which influenced osteoclastogenesis. Mechanistically, transient receptor potential subfamily V member 4 signaling was involved in force-induced Caspase-1-dependent pyroptosis in PDL progenitor cells. Overall, this study suggested a novel mechanism contributing to the modulation of osteoclastogenesis and alveolar bone remodeling under mechanical stimuli, indicating a promising approach to accelerate OTM by targeting Caspase-1.

Self-promoted electroactive biomimetic mineralized scaffolds for bacteria-infected bone regeneration.

Infected bone defects are a major challenge in orthopedic treatment. Native bone tissue possesses an endogenous electroactive interface that induces stem cell differentiation and inhibits bacterial adhesion and activity. However, traditional bone substitutes have difficulty in reconstructing the electrical environment of bone. In this study, we develop a self-promoted electroactive mineralized scaffold (sp-EMS) that generates weak currents via spontaneous electrochemical reactions to activate voltage-gated Ca2+ channels, enhance adenosine triphosphate-induced actin remodeling, and ultimately achieve osteogenic differentiation of mesenchymal stem cells by activating the BMP2/Smad5 pathway. Furthermore, we show that the electroactive interface provided by the sp-EMS inhibits bacterial adhesion and activity via electrochemical products and concomitantly generated reactive oxygen species. We find that the osteogenic and antibacterial dual functions of the sp-EMS depend on its self-promoting electrical stimulation. We demonstrate that in vivo, the sp-EMS achieves complete or nearly complete in situ infected bone healing, from a rat calvarial defect model with single bacterial infection, to a rabbit open alveolar bone defect model and a beagle dog vertical bone defect model with the complex oral bacterial microenvironment. This translational study demonstrates that the electroactive bone graft presents a promising therapeutic platform for complex defect repair.

Analysis of oral microbiome on temporary anchorage devices under different periodontal conditions.

BACKGROUND: Temporary anchorage devices (TADs) are maximum anchorages that have been widely used in orthodontic treatment. The aim of the study was to uncover whether a history of periodontitis would influence microbiome colonization on the TAD surface. RESULTS: Patients were grouped by periodontal evaluations before the orthodontic treatment. Patients with healthy periodontal conditions were classified as the healthy group, and patients diagnosed with periodontitis stage II or even worse were classified as the periodontitis group. Scanning electron microscopy (SEM) was used to analyze the existence of biofilm on the surface of 4 TADs from the healthy group and 4 TADs from the periodontitis group. Fifteen TADs from the healthy group and 12 TADs from the periodontitis group were collected. The microorganisms on the surface of TADs were harvested and analyzed by 16S rRNA gene sequencing. α-diversity indices and ß-diversity indices were calculated. Wilcoxon's test was used to determine differences between genera, species as well as KEGG functions. SEM analysis revealed bacteria colonization on the surface of TADs from both groups. Principal coordinate analysis (PCoA) based on ß diversity revealed differential sample clusters depending on periodontal conditions (P < 0.01). When comparing specific genera, Fusobacterium, Porphyromonas, Saccharibacteria_(TM7)_[G-1], Dialister, Parvimonas, Fretibacterium, Treponema were more enriched in TADs in the periodontitis group. In the KEGG analysis, TADs in the periodontitis group demonstrated enriched microbial activities involved with translation, genetic information processing, metabolism, and cell motility. CONCLUSIONS: This analysis elucidated the difference in total composition and function of TADs oral microorganisms between patients periodontally healthy and with periodontitis.

Orthodontic craniofacial pattern diagnosis: cephalometric geometry and machine learning.

Efficient and reliable diagnosis of craniofacial patterns is critical to orthodontic treatment. Although machine learning (ML) is time-saving and high-precision, prior knowledge should validate its reliability. This study proposed a craniofacial ML diagnostic workflow base on a cephalometric geometric model through clinical verification. A cephalometric geometric model was established to determine the landmark location by analyzing 408 X-ray lateral cephalograms. Through geometric information and feature engineering, nine supervised ML algorithms were conducted for sagittal and vertical skeleton patterns. After dimension reduction, plane decision boundary and landmark contribution contours were depicted to demonstrate the diagnostic consistency and the consistency with clinical norms. As a result, multi-layer perceptron achieved 97.56% accuracy for sagittal, while linear support vector machine reached 90.24% for the vertical. Sagittal diagnoses showed average superiority (91.60 ± 5.43)% over the vertical (82.25 ± 6.37)%, where discriminative algorithms exhibited more steady performance (93.20 ± 3.29)% than the generative (85.98 ± 9.48)%. Further, the Kruskal-Wallis H test was carried out to explore statistical differences in diagnoses. Though sagittal patterns had no statistical difference in diagnostic accuracy, the vertical showed significance. All aspects of the tests indicated that the proposed craniofacial ML workflow was highly consistent with clinical norms and could supplement practical diagnosis.

Subjective evaluation of facial asymmetry with three-dimensional simulated images among the orthodontists and laypersons: a cross-sectional study.

OBJECTIVES: We used three-dimensional (3D) virtual images to undertake a subjective evaluation of how different factors affect the perception of facial asymmetry among orthodontists and laypersons with the aim of providing a quantitative reference for clinics. MATERIALS AND METHODS: A 3D virtual symmetrical facial image was acquired using FaceGen Modeller software. The left chin, mandible, lip and cheek of the virtual face were simulated in the horizontal (interior/exterior), vertical (up/down), or sagittal (forward or backward) direction in 3, 5, and 7 mm respectively with Maya software to increase asymmetry for the further subjective evaluation. A pilot study was performed among ten volunteers and 30 subjects of each group were expected to be included based on 80% sensitivity in this study. The sample size was increased by 60% to exclude incomplete and unqualified questionnaires. Eventually, a total of 48 orthodontists and 40 laypersons evaluated these images with a 10-point visual analog scale (VAS). The images were presented in random order. Each image would stop for 30 s for observers with a two-second interval between images. Asymmetry ratings and recognition accuracy for asymmetric virtual faces were analyzed to explore how different factors affect the subjective evaluation of facial asymmetry. Multivariate linear regression and multivariate logistic regression models were used for statistical data analysis. RESULTS: Orthodontists were found to be more critical of asymmetry than laypersons. Our results showed that observers progressively decreased ratings by 1.219 on the VAS scale and increased recognition rates by 2.301-fold as the degree of asymmetry increased by 2 mm; asymmetry in the sagittal direction was the least noticeable compared with the horizontal and vertical directions; and chin asymmetry turned out to be the most sensitive part among the four parts we simulated. Mandible asymmetry was easily confused with cheek asymmetry in the horizontal direction. CONCLUSIONS: The degree, types and parts of asymmetry can affect ratings for facial deformity as well as the accuracy rate of identifying the asymmetrical part. Although orthodontists have higher accuracy in diagnosing asymmetrical faces than laypersons, they fail to correctly distinguish some specific asymmetrical areas.

The effect of maxillary molar distalization with clear aligner: a 4D finite-element study with staging simulation.

INTRODUCTION: Long-term simulation of tooth movement is crucial for clear aligner (CA) treatment. This study aimed to investigate the effect of maxillary molar distalization with CA via an automatic staging simulation. METHOD: A finite-element method (FEM) model of maxillary dentition, periodontal ligaments, attachments, and corresponding CA was established, and a prescribed 2-mm distalization with 0.1 mm each step of the second molar was simulated. The long-term tooth movement under orthodontic force was simulated with an iterative computation method. The morphologic changes of CA during staging were simulated with the thermal expansion method. RESULTS: Twenty steps of molar distalization were simulated. Significant distal tilting of the second molar was revealed, along with the proclination of anterior teeth, which caused the 'reversed bow effect'. For the second molar, 4.63°distal tilting at the 20th step was revealed. The intrusion of the incisors and the second molar were 0.43 mm, 0.39 mm, and 0.45 mm, respectively, at step 20. All the anterior teeth showed a proclination of approximately 1.41°-2.01° at the 20th step. The expression rate of the designed distalization of the second molar was relatively low (approximately 68%) compared to the high efficacy of interdental space opening between molars with CA (approximately 89%). CONCLUSION: A novel method of simulating long-term molar distalization with CA with FEM was developed. The FEM results suggested distal tilting of the second molar and the proclination of anterior teeth during the molar distalization.

Expansion rebound deformation of clear aligners and its biomechanical influence: a three-dimensional morphologic analysis and finite element analysis study.

OBJECTIVES: To determine the expansion rebound deformation (ERD) of clear aligners (CAs) and its biomechanical influence. MATERIALS AND METHODS: A four-premolar extraction treatment plan was carried out for a patient with 2 CA companies. Thirty-six digitally scanned clear aligners with the corresponding 36 virtually constructed "ideal" aligners were constructed. The arch width and length between pairs of reference landmarks of the scanned CAs and corresponding dentition models were measured. Cone-beam computed tomography data and digital dental models were used for three-dimensional (3D) finite element analysis (FEA) modeling. Thirty-six scanned CA models with the corresponding 36 ideal CA models were constructed. One-way analysis of variance was used to determine the differences among deviation values at tooth level, and paired t-test was used to compare the displacements of teeth between the two group of CAs. RESULTS: All CAs were wider and shorter than the digital model from which they were constructed. In the scanned CA model group, significant stress was observed in the buccolingual area of the periodontal ligament on posterior teeth, and the corresponding displacements of teeth were also noted. Significantly larger coronal displacements were noted for the lateral incisor, the canine, the second premolar, and the first molar in the scanned CA group (P < .05). CONCLUSIONS: The general trend of ERD of thermoformed CAs was shown. This deformation may cause unforeseen tooth movements and negatively affect treatment outcomes.

Effects of orthodontic camouflage treatment vs orthodontic-orthognathic surgical treatment on condylar stability in Class II hyperdivergent patients with severe temporomandibular joint osteoarthrosis: a retrospective observational study.

OBJECTIVES: To investigate the differences in profile changes and stability of the condyles between orthodontic camouflage treatment assisted by vertical control and that accomplished via orthognathic surgery in Class II hyperdivergent patients with TMJ osteoarthrosis (TMJOA). MATERIALS AND METHODS: This study included 27 Class II hyperdivergent TMJOA patients (54 condyles) who received orthodontic camouflage treatment (13 patients) or orthognathic surgery (14 patients) Cone-beam computerized tomography (CBCT) scans were taken before treatment (T1) and 1 year after treatment (T2). Cephalometric and TMJ measurement analyses were conducted to evaluate the change in profile and condyles from T1 to T2 using independent samples t-test and paired t-test. Three-dimensional (3D) deviation analysis was also performed to evaluate the stability of condyles from T1 to T2. RESULTS: Both groups showed significant profile improvement from T1 to T2. The changes in Z angle and ANB angle were larger in the surgical group than in the orthodontic group. Condylar width, length, and height remained stable after treatment in the orthodontic group (P > .05), while they reduced by 0.67 ± 0.85 mm, 1.14 ± 1.10 mm, and 1.07 ± 1.34 mm, respectively, in the surgical group (P < .05). Superior, posterior, medial, and lateral joint spaces were significantly reduced in the orthodontic group (P < .05). 3D deviations intuitively showed that condylar bone in the orthodontic group was more stable than that in the surgical group. CONCLUSIONS: For Class II hyperdivergent patients with severe TMJOA, orthodontic camouflage treatment with vertical control can effectively maintain the stability of condyles while significantly improving the profile. Surgical treatment yields a better profile but may increase the risk of condyle resorption.

Dental Pulp Stem Cell-Derived Exosomes Alleviate Mice Knee Osteoarthritis by Inhibiting TRPV4-Mediated Osteoclast Activation.

Osteoarthritis (OA) is a degenerative disease that causes chronic pain and joint swelling and even disables millions of patients. However, current non-surgical treatment for OA can only relieve pain without obvious cartilage and subchondral bone repair. Mesenchymal stem cell (MSC)-secreted exosomes have promising therapeutic effects on knee OA, but the efficacy of MSC-exosome therapy is not well determined, and the mechanisms involved are still unclear. In this study, we isolated dental pulp stem cell (DPSC)-derived exosomes by ultracentrifugation and determined the therapeutic effects of a single intra-articular injection of DPSC-derived exosomes in a mice knee OA model. The results showed that the DPSC-derived exosomes effectively improved abnormal subchondral bone remodeling, inhibited the occurrence of bone sclerosis and osteophytes, and alleviated cartilage degradation and synovial inflammation in vivo. Moreover, transient receptor potential vanilloid 4 (TRPV4) was activated during the progression of OA. Enhanced TRPV4 activation facilitated osteoclast differentiation, and TRPV4 inhibition blocked this process in vitro. DPSC-derived exosomes repressed osteoclast activation in vivo by inhibiting TRPV4 activation. Our findings demonstrated that a topical, single injection of DPSC-derived exosomes is a potential strategy for knee OA treatment, and that the exosomes regulated osteoclast activation by TRPV4 inhibition, which may act as a promising target for clinical OA treatment.

Oral microbiome contributes to the failure of orthodontic temporary anchorage devices (TADs).

BACKGROUND: The stability of temporary anchorage devices (TADs) is critical in orthodontic clinics. The failure of TADs is multifactorial, and the role of the oral microbiome has not been clearly defined. Herein, we attempted to analyze the contribution of the oral microbiome to the failure of TADs. METHODS: Next-generation sequencing was adopted for analyzing the microbiome on the TADs from orthodontic patients. 29 TADs (15 failed TADs and 14 successful TADs) were used for 16S rRNA gene sequencing. A total of 135 TADs (62 failed TADs and 73 successful TADs) were collected to conduct metagenomic sequencing. Additionally, 34 verified samples (18 failed TADs and 16 successful TADs) were collected for quantitative real-time polymerase chain reaction analysis (qRT-PCR). RESULTS: Successful and failed TADs demonstrated discrepancies in microbiome structure, composition, and function. Clear separations were found in ß-diversity in 16S rRNA gene sequencing as well as metagenomic sequencing (p < 0.05). Metagenomic sequencing showed that Prevotella intermedia, Eikenella corrodens, Parvimonas spp., Neisseria elongata, and Catonella morbi were enriched in the failed groups. qRT-PCR also demonstrated that the absolute bacteria load of Prevotella intermedia was higher in failed TADs (p < 0.05). Considering functional aspects, the failed group showed enriched genes involved in flagellar assembly, bacterial chemotaxis, and oxidative phosphorylation. CONCLUSIONS: This study illustrated the compositional and functional differences of microorganisms found on successful and failed TADs, indicating that controlling bacterial adhesion on the surface of TADs is essential for their success rate.

A quantitative analysis of facial changes after orthodontic treatment with vertical control in patients with idiopathic condylar resorption.

OBJECTIVE: This study aimed to investigate temporomandibular joint (TMJ) stability and three-dimensional (3D) facial changes in class II hyperdivergent patients with stable idiopathic condylar resorption (ICR) after orthodontic camouflage treatment with vertical control by using temporary anchorage devises (TADs). METHODS: Nineteen skeletal class II hyperdivergent patients who were diagnosed with stable ICR underwent bicuspid extraction orthodontic treatment with vertical control via TADs were enrolled. TMJ was evaluated with the cone beam computerized tomography (CBCT) and clinical records before and after treatment. Changes in dental and skeletal parameters were evaluated with cephalometric and dental cast measurements. The 3D morphable model (3DMM) method was performed with the MeshMonk toolbox for the 3D facial analysis. After the reposition and landmark setting process, 3D facial heatmaps were used to illustrate facial changes, and the 3D deviations of landmarks were calculated. RESULTS: Both the imaging evaluation and clinical examination proved that TMJs remained stable after treatment. The retrusion of the upper and lower incisors reached 6.63 ± 0.79 mm and 3.78 ± 1.49 mm. The intrusion of the upper first molar reached 2.65 ± 0.75 mm, with a 2.27 ± 0.82° counterclockwise rotation of the mandibular plane. An upward shift of the soft tissue pogonion (2.34 ± 2.03 mm) and protrusion of Po-NB (0.82 ± 0.70 mm) was gained. Larger intrusion was found in the lower lip (3.29 ± 0.80 mm) than in the upper lip (2.20 ± 0.69 mm). CONCLUSION: Camouflage orthodontic treatment with TAD for vertical control is acceptable for skeletal class II hyperdivergent patients with ICR, which can improve the facial profile.

Effect of Different Anchorage Reinforcement Methods on Long-Term Maxillary Whole Arch Distalization with Clear Aligner: A 4D Finite Element Study with Staging Simulation.

The objective of this study was to examine how various anchorage methods impact long-term maxillary whole arch distalization using clear aligners (CAs) through an automated staging simulation. Three different anchorage reinforcement methods, namely, Class II elastics, buccal temporary anchorage device (TAD), and palatal TAD, were designed. Orthodontic tooth movement induced by orthodontic forces was simulated using an iterative computation method. Additionally, the automatic adjustment of the CA was simulated through the application of the thermal expansion method. The results indicated that the palatal TAD group had the largest retraction of incisors, followed by the buccal TAD group and the Class II elastic group, while the least was in the control group. The largest distal displacements and efficiency of molar distalization for the first and the second molars were noticed in the palatal TAD group. Arch width increased at the molar and premolar levels in all groups. The FEM results suggested palatal TAD had the best performance considering anterior teeth anchorage maintenance, both sagittally and vertically. However, attention should be paid to the possible increasement of arch width.

Microbiological Advances in Orthodontics: An Overview and Detailed Analysis of Temporary Anchorage Devices.

Dental biofilm is the initiating factor of oral diseases, such as periodontitis and caries. Orthodontic treatment could alter the microbiome structure balance, and increase the risk of such diseases. Furthermore, fixed appliances can induce temporary changes in the microbiome community, and the changes that clear aligners bring are smaller by comparison. Temporary anchorage devices (TADs) are skeletal anchorages that are widely used in orthodontic treatment. Microorganisms affect the occurrence and development of inflammation surrounding TADs. At present, existing researches have verified the existence of plaque biofilm on the surface of TADs, but the formation of plaque biofilm and plaque composition under different stable conditions have not been fully understood. The development of high-throughput sequencing, molecular biology experiments, and metabonomics have provided new research ideas to solve this problem. They can become an effective means to explore the microbiome surrounding TADs.

A New HIV-1 K28E32-Reverse Transcriptase Variant Associated with the Rapid Expansion of CRF07_BC among Men Who Have Sex with Men.

HIV-1 CRF07_BC originated among injection drug users (IDUs) in China. After diffusing into men who have sex with men (MSM), CRF07_BC has shown a rapid expansion in this group; however, the mechanism remains unclear. Here, we identified a new K28E32 variant of CRF07_BC that was characterized by five specific mutations (E28K, K32E, E248V, K249Q, and T338S) in reverse transcriptase. This variant was mainly prevalent among MSM, and was overrepresented in transmission clusters, suggesting that it could have driven the rapid expansion of CRF07_BC in MSM, though founder effects cannot be ruled out. It was descended from an evolutionary intermediate accumulating four specific mutations and formed an independent phylogenetic node with an estimated origin time in 2003. The K28E32 variant was demonstrated to have significantly higher in vitro HIV-1 replication ability than the wild type. Mutations E28K and K32E play a critical role in the improvement of in vitro HIV-1 replication ability, reflected by improved reverse transcription activity. The results could allow public health officials to use this marker (especially E28K and K32E mutations in the reverse transcriptase (RT) coding region) to target prevention measures prioritizing MSM population and persons infected with this variant for test and treat initiatives. IMPORTANCE HIV-1 has very high mutation rate that is correlated with the survival and adaption of the virus. The variants with higher transmissibility may be more selective advantage than the strains with higher virulence. Several HIV-1 variants were previously demonstrated to be correlated with higher viral load and lower CD4 T cell count. Here, we first identified a new variant (the K28E32 variant) of HIV-1 CRF07_BC, described its origin and evolutionary dynamics, and demonstrated its higher in vitro HIV-1 replication ability than the wild type. We demonstrated that five RT mutations (especially E28K and K32E) significantly improve in vitro HIV-1 replication ability. The appearance of the new K28E32 variant was associated with the rapidly increasing prevalence of CRF07_BC among MSM.

Neural regulation of alveolar bone remodeling and periodontal ligament metabolism during orthodontic tooth movement in response to therapeutic loading.

With increased understanding of orthodontic tooth movement (OTM) in recent years, neural regulation of OTM has become an emerging and expanding area of research. Numerous studies have shown that the nervous system, including the central and peripheral systems, regulates bone remodeling through various neuropeptides, receptor expression, etc. OTM is a unique periodontal tissue remodeling process induced by mechanical force, including changes in the periodontal ligament metabolism and alveolar bone remodeling. Various studies have shown that the nervous system participates in the OTM process and regulates the periodontal ligament metabolism. This review summarizes the current researches on neural regulation of bone remodeling and the biological responses within the periodontal ligamentduring OTM under therapeutic loading. We also discuss the issues that remain to be addressed in this field. The exploration of neural regulation on OTM not only assists us to understand the mechanism of OTM more thoroughly, but also provides a new insight to accelerate tooth movement in the future.

The accuracy of a three-dimensional face model reconstructing method based on conventional clinical two-dimensional photos.

BACKGROUND: This study aims to investigate the accuracy of a three-dimensional (3D) face reconstruction method based on conventional clinical two-dimensional (2D) photos. METHODS: Twenty-three patients were included, and Character Creator v3.2 software with the Headshot v1.0 plugin was used for 3D face model reconstruction. Various facial landmarks were finely adjusted manually to refine the models. After preprocessing and repositioning, 3D deviation analysis was performed. The accuracy of the landmarks in different dimensions was determined, and twelve facial soft tissue measurements were compared to validate the clinical potential of the method. RESULT: The reconstructed 3D face models showed good facial morphology with fine texture. The average root mean square errors between face scan models and reconstructed models at perioral area (1.26 ± 0.24 mm, 95%CI: 1.15-1.37 mm) were significantly smaller than the entire facial area (1.77 ± 0.23 mm, 95%CI:1.67-1.88 mm), P < 0.01. The deviation of menton of soft tissue was significantly larger than pronasale (P < 0.01). The deviations of all landmarks in the Y-direction were significantly larger than those in the other 2 dimensions (Y > Z > X, P < 0.01). A significant difference (P < 0.05) of approximately 1.5 mm was found for facial height. Significant differences (P < 0.05) were also identified in the remaining 6 soft tissue measurements, with average deviations no greater than 0.5 mm (linear measurement) or 1.2° (angular measurements). CONCLUSION: A 3D face modeling method based on 2D face photos was revealed and validated. The reconstruction accuracy of this method is clinically acceptable for orthodontic measurement purposes, but narrow clinical indications and labor-intensive operations remain problems.