RESUMO
OBJECTIVES: This clinical study aimed to assess the trueness of three intraoral scanners for the recor-ding of the maximal intercuspal position (MIP) to provide a reference for clinical practice. METHODS: Ten participants with good occlusal relationship and healthy temporomandibular joint were recruited. For the control group, facebow transferring procedures were performed, and bite registrations at the MIP were used to transfer maxillary and mandibular casts to a mechanical articulator, which were then scanned with a laboratory scanner to obtain digital cast data. For the experimental groups, three intraoral scanners (Trios 3, Carestream 3600, and Aoralscan 3) were used to obtain digital casts of the participants at the MIP following the scanning workflows endorsed by the corresponding manufacturers. Subsequently, measurement points were marked on the control group's digital casts at the central incisors, canines, and first molars, and corresponding distances between these points on the maxillary and mandibular casts were measured to calculate the sum of measured distances (DA). Distances between measurement points in the incisor (DI), canine (DC), and first molar (DM) regions were also calculated. The control group's maxillary and mandibular digital casts with the added measurement points were aligned with the experimental group's casts, and DA, DI, DC, and DM values of the aligned control casts were determined. Statistical analysis was performed on DA, DI, DC, and DM obtained from both the control and experimental groups to evaluate the trueness of the three intraoral scanners for the recording of MIP. RESULTS: In the control group, DA, DI, DC, and DM values were (39.58±6.40), (13.64±3.58), (14.91±2.85), and (11.03±1.56) mm. The Trios 3 group had values of (38.99±6.60), (13.42±3.66), (14.55±2.87), and (11.03±1.69) mm. The Carestream 3600 group showed values of (38.57±6.36), (13.56±3.68), (14.45±2.85), and (10.55±1.41) mm, while the Aoralscan 3 group had values of (38.16±5.69), (13.03±3.54), (14.23±2.59), and (10.90±1.54) mm. Analysis of variance revealed no statistically significant differences between the experimental and control groups for overall deviation DA (P=0.96), as well as local deviations DI (P=0.98), DC (P=0.96), and DM (P=0.89). CONCLUSIONS: With standardized scanning protocols, the three intraoral scanners demonstrated comparable trueness to traditional methods in recording MIP, fulfilling clinical requirements.
Assuntos
Incisivo , Dente Molar , Humanos , Mandíbula , Maxila , Desenho Assistido por Computador , Imageamento Tridimensional , Técnica de Moldagem OdontológicaRESUMO
OBJECTIVES: This clinical study aimed to evaluate the accuracy of a fully digital technique for measuring sagittal condylar inclination (SCI), as well as validating whether differences existed between the left and right SCI values of the same participant, to provide a reference for clinical practice. METHODS: Ten participants with good occlusal relationship and normal temporomandibular joint were recruited. Three methods were used to measure the SCI values of the participants, namely, A (mechanical facebow transferring and mechanical articulator-based measuring method with physical protrusive interocclusal registration), B (face scan-based virtual facebow and virtual articulator-based measuring method with digital protrusive interocclusal registration), and C (jaw motion tracking system-based measuring method). With the group subjected to methods A and C as the control, the SCI values obtained by the three methods were statistically analyzed. The left and right SCI values of the same participant were also compared. RESULTS: The left and right SCI values measured by method A were 41.70°±7.09° and 42.80°±8.62°, those by method B were 35.09°±12.49° and 37.63°±12.10°, and those by method C were 39.43°±8.72° and 38.45°±6.91°. No significant difference existed among the SCI values measured by the three methods (P>0.05). Meanwhile, no statistical difference existed between the SCI values on the left and right sides of the same participant (P>0.05). CONCLUSIONS: The accuracy of the virtual facebow and digital protrusive occlusal registration based SCI measuring method was the same as that of mechanical facebow based and jaw motion tracking system-based methods. The SCI values on the left and right sides of the same participant were similar. Clinically, an appropriate SCI measurement and setting strategy can be selected based on the actual situations.
Assuntos
Côndilo Mandibular , Articulação Temporomandibular , Humanos , Registro da Relação Maxilomandibular/métodos , Articuladores Dentários , Aparelhos de Tração ExtrabucalRESUMO
A digital approach to fabricating a custom holder to attach a mandibular sensor of an optical jaw motion tracking system is described. Typically, jaw motion tracking systems come with standard holders. However, additional chairside time is still required to adapt the holder's arm to the individual arch and securely attach the holder to the mandibular teeth. Moreover, the placement of the standard holder is problematic in patients with a deep vertical overlap or with short clinical crowns. This technique offers a digital approach to designing and fabricating a custom holder in situations where standard holders cannot be efficiently attached. The custom holder is designed to accommodate the available space without interfering with the occlusion, thereby minimizing the time needed to attach the holder and optimizing the workflow for clinical jaw motion tracking.
RESUMO
The design of engineered living materials (ELMs) is an emerging field developed from synthetic biology and materials science principles. ELMs are multi-scale bulk materials that combine the properties of self-healing and organism adaptability with the designed physicochemical or mechanical properties for functional applications in various fields, including therapy, electronics, and architecture. Among the many ELM design and manufacturing methods, three-dimensional (3D) bioprinting stands out for its precise control over the structure of the fabricated constructs and the spatial distribution of cells. In this review, we summarize the progress in the field, cell type and material selection, and the latest applications of 3D bioprinting to manufacture ELMs, as well as their advantages and limitations, hoping to deepen our understanding and provide new insights into ELM design. We believe that 3D bioprinting will become an important development direction and provide more contributions to this field.