Synthesis of δ-MnO2 via ozonation routine for low temperature formaldehyde removal.

Nowadays, it is still a challenge to prepared high efficiency and low cost formaldehyde (HCHO) removal catalysts in order to tackle the long-living indoor air pollution. Herein, δ-MnO2 is successfully synthesized by a facile ozonation strategy, where Mn2+ is oxidized by ozone (O3) bubble in an alkaline solution. It presents one of the best catalytic properties with a low 100% conversion temperature of 85°C for 50 ppm of HCHO under a GHSV of 48,000 mL/(g·hr). As a comparison, more than 6 times far longer oxidation time is needed if O3 is replaced by O2. Characterizations show that ozonation process generates a different intermediate of tetragonal ß-HMnO2, which would favor the quick transformation into the final product δ-MnO2, as compared with the relatively more thermodynamically stable monoclinic γ-HMnO2 in the O2 process. Finally, HCHO is found to be decomposed into CO2 via formate, dioxymethylene and carbonate species as identified by room temperature in-situ diffuse reflectance infrared fourier transform spectroscopy. All these results show great potency of this facile ozonation routine for the highly active δ-MnO2 synthesis in order to remove the HCHO contamination.

Protons intercalation induced hydrogen bond network in δ-MnO2 cathode for high-performance aqueous zinc-ion batteries.

Birnessite-type MnO2 (δ-MnO2) exhibits great potential as a cathode material for aqueous zinc-ion batteries (AZIBs). However, the structural instability and sluggish reaction kinetics restrict its further application. Herein, a unique protons intercalation strategy was utilized to simultaneously modify the interlayer environment and transition metal layers of δ-MnO2. The intercalated protons directly form strong O  H bonds with the adjacent oxygens, while the increased H2O molecules also establish a hydrogen bond network (O  H···O) between H2O molecules or bond with adjacent oxygens. Based on the Grotthuss mechanism, these bondings ultimately enhance the stability of layered structures and facilitate the rapid diffusion of protons. Moreover, the introduction of protons induces numerous oxygen vacancies, reduces steric hindrance, and accelerates ion transport kinetics. Consequently, the protons intercalated δ-MnO2 (H-MnO2-x) demonstrates exceptional specific capacity of 401.7 mAh/g at 0.1 A/g and a fast-charging performance over 1000 cycles. Density functional theory analysis confirms the improved electronic conductivity and reduced diffusion energy barrier. Most importantly, electrochemical quartz crystal microbalance tests combining with ex-situ characterizations verify the inhibitory effect of the interlayer proton environment on basic zinc sulfate formation. Protons intercalation behavior provides a promising avenue for the development of MnO2 as well as other cathodes in AZIBs.

Greener Approach for Synthesis of δ-MnO2 Nanoparticles: Access to Pharmaceutically Important Pyrimidines and their Antimicrobial Activity Studies.

A sustainable approach for pharmaceutically important pyrimidine derivatives is achieved by using biogenically produced single-phase δ-MnO2 NPs under external ligand-free conditions. The phytochemicals that comprise the extract of Areca Nut Husk (ANH) have been discovered to serve as reducing agents. The role of phytochemicals is not only to aid in the reduction of Mn(VII) into Mn(IV), but they also have an important role in stabilizing the catalyst. The establishment of δ-MnO2 NPs was confirmed inveterate by FE-SEM, p-XRD, ICP-OES (Mn content = 43.17% w/w), EDX, and with an active Mn content of 43.17% w/w. A series of pyrimidine derivatives were prepared in good yields using a one-pot multicomponent synthesis approach under atmospheric conditions. In addition, hot filtration tests, control experiments, gram-scale synthesis, and mechanistic investigations were demonstrated. Additionally, antimicrobial activity studies of δ-MnO2 NPs and pyrimidine derivatives against the Gram-negative bacteria E. coli, growth curve and minimum inhibitory concentration were studied.

Facile synthesis of δ-MnO2 biotemplated by waste tobacco stem-silks for enhanced removal of Sb(III).

The elimination of antimony pollution has attracted increasing concerns because of its high toxicity to human health and the natural environment. In this work, biomimetic δ-MnO2 was synthesized by using waste tobacco stem-silks as biotemplate (Bio-δ-MnO2) and used in the capture of Sb(III)from aqueous solution. The tobacco stem-silks not only provided unique wrinkled morphologies but also contained carbon element self-doped into the resulting samples. The maximum Sb(III) adsorption capacity reached 763.4 mg∙g -1, which is 2.06 times higher than δ-MnO2 without template (370.0 mg∙g -1), 4.53 times than tobacco stem-silks carbon (168.5 mg∙g -1), and 10.39 times than commercial MnO2 (73.5 mg∙g -1), respectively. The isotherm and kinetic studies indicated that the adsorption behavior was consistent with the Langmuir isotherm model and the pseudo-second-order kinetic equation. As far as we are aware, the adsorption capacity of Bio-δ-MnO2 is much higher than that of most Sb(III) adsorbents. FT-IR, XPS, SEM, XRD, and Zeta potential analyses showed that the main mechanism for the adsorption of Sb(III) by Bio-δ-MnO2 includes electrostatic attraction, surface complexation, and redox. Overall, this study provides a new sustainable way to convert agricultural wastes to more valuable products such as biomimetic adsorbent for Sb(III) removal in addition to conventional activated carbon and biochar.

Pre-intercalation of Ammonium Ions in Layered δ-MnO2 Nanosheets for High-Performance Aqueous Zinc-Ion Batteries.

Layered manganese dioxide is a promising cathode candidate for aqueous Zn-ion batteries. However, the narrow interlayer spacing, inferior intrinsic electronic conductivity and poor structural stability still limit its practical application. Herein, we report a two-step strategy to incorporate ammonium ions into manganese dioxide (named as AMO) nanosheets as a cathode for boosted Zn ion storage. K+ -intercalated δ-MnO2 nanosheets (KMO) grown on carbon cloth are chosen as the self-involved precursor. Of note, ammonium ions could replace K+ ions via a facile hydrothermal reaction to enlarge the lattice space and form hydrogen-bond networks. Compared with KMO, the structural stability and the ion transfer kinetics of the layered AMO are enhanced. As expected, the obtained AMO cathode exhibits remarkable electrochemical properties in terms of high reversible capacity, decent rate performance and superior cycling stability over 10000 cycles.

Layer-by-Layer Inkjet-Printed Manganese Oxide Nanosheets on Graphene for High-Performance Flexible Supercapacitors.

The widespread adoption of wearable, movable, and implantable smart devices has sparked the evolution of flexible, miniaturized power supplies. High-resolution inkjet printing of flexible microsupercapacitor (µSC) electrodes is a fast, inexpensive, and waste-free alternative manufacturing technology. In this work, a 2D birnessite-type manganese dioxide (δ-MnO2) water-based ink is used to print 10-25 layers of δ-MnO2 symmetrically on a preprinted interdigitated cell consisting of 10 layers of electrochemically exfoliated graphene (EEG). The cell with 10 printed layers of δ-MnO2 achieved the highest specific capacitance, energy density, and power density of 0.44 mF cm-2, 0.045 µW h cm-2, and 0.0012 mW cm-2, respectively. Since inkjet-printing technology supports µSC manufacturing with parallel/series connectivity, four cells were used to study and improve the potential window and capacitance that can be used to construct µSC arrays as power banks. This work provides the first approach for designing an inkjet-printed interdigitated hybrid cell based on δ-MnO2@EEG that could be a versatile candidate for the large-scale production of flexible and printable electronic devices for energy storage.

Effectively Modulating Oxygen Vacancies in Flower-Like δ-MnO2 Nanostructures for Large Capacity and High-Rate Zinc-Ion Storage.

In recent years, manganese-based oxides as an advanced class of cathode materials for zinc-ion batteries (ZIBs) have attracted a great deal of attentions from numerous researchers. However, their slow reaction kinetics, limited active sites and poor electrical conductivity inevitably give rise to the severe performance degradation. To solve these problems, herein, we introduce abundant oxygen vacancies into the flower-like δ-MnO2 nanostructure and effectively modulate the vacancy defects to reach the optimal level (δ-MnO2-x-2.0). The smart design intrinsically tunes the electronic structure, guarantees ion chemisorption-desorption equilibrium and increases the electroactive sites, which not only effectively accelerates charge transfer rate during reaction processes, but also endows more redox reactions, as verified by first-principle calculations. These merits can help the fabricated δ-MnO2-x-2.0 cathode to present a large specific capacity of 551.8 mAh g-1 at 0.5 A g-1, high-rate capability of 262.2 mAh g-1 at 10 A g-1 and an excellent cycle lifespan (83% of capacity retention after 1500 cycles), which is far superior to those of the other metal compound cathodes. In addition, the charge/discharge mechanism of the δ-MnO2-x-2.0 cathode has also been elaborated through ex situ techniques. This work opens up a new pathway for constructing the next-generation high-performance ZIBs cathode materials.

Efficacy and mechanisms of δ-MnO2 modified biochar with enhanced porous structure for uranium(VI) separation from wastewater.

Even though uranium (U) is considered to be an essential strategic resource with vital significance to nuclear power development and climate change mitigation, U exposure to human and ecological environment has received growing concerns due to its both highly chemically toxic and radioactively hazardous property. In this study, a composite (M-BC) based on Ficus macrocarpa (banyan tree) aerial roots biochar (BC) modified by δ-MnO2 was designed to separate U(VI) from synthetic wastewater. The results showed that the separation capacity of M-BC was 61.53 mg/g under the solid - liquid ratio of 1 g/L, which was significantly higher than that of BC (12.39 mg/g). The separation behavior of U(VI) both by BC and M-BC fitted well with Freundlich isothermal models, indicating multilayer adsorption occurring on heterogeneous surfaces. The reaction process was consistent with the pseudo-second-order kinetic model and the main rate-limiting step was particle diffusion process. It is worthy to note that the removal of U(VI) by M-BC was maintained at 94.56% even after five cycles, indicating excellent reusability and promising application potential. Multiple characterization techniques (e.g. Scanning Electron Microscope-Energy Dispersive Spectrometer (SEM-EDS), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Brunauer-Emmett-Teller (BET) and X-ray Photoelectron Spectroscopy (XPS)) uncovered that U(VI) complexation with oxygen-containing functional groups (e.g. O-CO and Mn-O) and cation exchange with protonated ≡MnOH were the dominant mechanisms for U(VI) removal. Application in real uranium wastewater treatment showed that 96% removal of U was achieved by M-BC and more than 92% of co-existing (potentially) toxic metals such as Tl, Co, Pb, Cu and Zn were simultaneously removed. The work verified a feasible candidate of banyan tree aerial roots biowaste based δ-MnO2-modified porous BC composites for efficient separation of U(VI) from uranium wastewater, which are beneficial to help address the dilemma between sustainability of nuclear power and subsequent hazard elimination.

An Artificial MnWO4 Cathode Electrolyte Interphase Enabling Enhanced Electrochemical Performance of δ-MnO2 Cathode for Aqueous Zinc Ion Battery.

The dissolution of active material in aqueous batteries can lead to a rapid deterioration in capacity, and the presence of free water can also accelerate the dissolution and trigger some side reactions that affect the service life of aqueous batteries. In this study, a MnWO4 cathode electrolyte interphase (CEI) layer is constructed on a δ-MnO2 cathode by cyclic voltammetry, which is effective in inhibiting the dissolution of Mn and improving the reaction kinetics. As a result, the CEI layer enables the δ-MnO2 cathode to produce a better cycling performance, with the capacity maintained at 98.2% (vs. activated capacity at 500 cycles) after 2000 cycles at 10 A g-1. In comparison, the capacity retention rate is merely 33.4% for pristine samples in the same state, indicating that this MnWO4 CEI layer constructed by using a simple and general electrochemical method can promote the development of MnO2 cathodes for aqueous zinc ion batteries.

Exceptional Ozone Decomposition over δ-MnO2/AC under an Entire Humidity Environment.

Ozone (O3) pollution is highly detrimental to human health and the ecosystem due to it being ubiquitous in ambient air and industrial processes. Catalytic decomposition is the most efficient technology for O3 elimination, while the moisture-induced low stability represents the major challenge for its practical applications. Here, activated carbon (AC) supported δ-MnO2 (Mn/AC-A) was facilely synthesized via mild redox in an oxidizing atmosphere to obtain exceptional O3 decomposition capacity. The optimal 5Mn/AC-A achieved nearly 100% of O3 decomposition at a high space velocity (1200 L g-1 h-1) and remained extremely stable under entire humidity conditions. The functionalized AC provided well-designed protection sites to inhibit the accumulation of water on δ-MnO2. Density functional theory (DFT) calculations confirmed that the abundant oxygen vacancies and a low desorption energy of intermediate peroxide (O22-) can significantly boost O3 decomposition activity. Moreover, a kilo-scale 5Mn/AC-A with low cost (∼1.5 $/kg) was used for the O3 decomposition in practical applications, which could quickly decompose O3 pollution to a safety level below 100 µg m-3. This work offers a simple strategy for the development of moisture-resistant and inexpensive catalysts and greatly promotes the practical application of ambient O3 elimination.

Toward the High-Performance Lithium Primary Batteries by Chemically Modified Fluorinate Carbon with δ-MnO2.

Li/CFx battery is one of the most promising lithium primary batteries (LPBs) which yields the highest energy density but with poor rate capability. This Achilles'' heel hinders the large-scale applications of Li/CFx batteries. This work first reports a facile chemical modification method of CFx with δ-MnO2 . Having benefited from the chemical bonding, the electrochemical performance at high-rate discharge is remarkably enhanced without compromising the specific capacity. The coin cells exhibit an energy density of 1.94 × 103  Wh kg-1 at 0.2 C, which is approaching the theoretical energy density of commercial fluorinated graphite (2.07 × 103  Wh kg-1 ). A power density of 5.49 × 104  W kg-1 at 40 C associated with an energy density of 4.39 × 102  Wh kg-1 , which is among the highest value of Li/CFx batteries, are obtained. Besides, the punch batteries achieve an ultrahigh power density of 4.39 × 104  W kg-1 with an energy density of 7.60 × 102  Wh kg-1 at 30 C. The intrinsic reasons for this outstanding electrochemical performance, which are known as the fast Li+ diffusion kinetics guided by thin δ-MnO2 flakes and the low formation energy barrier caused by chemical bonding, are explored by the galvanostatic intermittent titration technique (GITT) and theoretical calculations.

Sodium Ion Pre-Intercalation of δ-MnO2 Nanosheets for High Energy Density Aqueous Zinc-Ion Batteries.

With the merits of low cost, environmental friendliness and rich resources, manganese dioxide is considered to be a promising cathode material for aqueous zinc-ion batteries (AZIBs). However, its low ion diffusion and structural instability greatly limit its practical application. Hence, we developed an ion pre-intercalation strategy based on a simple water bath method to grow in situ δ-MnO2 nanosheets on flexible carbon cloth substrate (MnO2), while pre-intercalated Na+ in the interlayer of δ-MnO2 nanosheets (Na-MnO2), which effectively enlarges the layer spacing and enhances the conductivity of Na-MnO2. The prepared Na-MnO2//Zn battery obtained a fairly high capacity of 251 mAh g-1 at a current density of 2 A g-1, a satisfactory cycle life (62.5% of its initial capacity after 500 cycles) and favorable rate capability (96 mAh g-1 at 8 A g-1). Furthermore, this study revealed that the pre-intercalation engineering of alkaline cations is an effective method to boost the properties of δ-MnO2 zinc storage and provides new insights into the construction of high energy density flexible electrodes.

Urea-H2O2 defect engineering of δ-MnO2 for propane photothermal oxidation: Structure-activity relationship and synergetic mechanism determination.

Photothermal catalysis has an advantage in effective and economical elimination technology of volatile organic compounds (VOCs) in the ascendant. Herein, various surface defect engineering routes were adopted to enhance the low-temperature propane oxidation of δ-MnO2. Compared to reducing etchants urea and vitamin C, δ-MnO2 treated with urea - H2O2 exhibited an excellent thermal (T90 = 240 ℃) and photothermal (T90 = 196 ℃) activities of propane oxidation. Urea - H2O2 treatment provided high concentration of Mn4+ and surface-active oxygen (Mn4+-Osur) species as surface-active sites, and produced numerous oxygen vacancies to improve charge separation and superoxide species generation capacity. Thus, the photothermal conversion efficiency and low-temperature reducibility were remarkably enhanced. Furthermore, the photothermal synergistic catalytic mechanism was proposed based on in-situ diffuse reflectance infrared Fourier transform spectroscopy and control experiments. The strategy here offered insight into the rational design of efficient transition catalysts, and in-depth understanding of the photothermal catalytic VOCs removal mechanism.

Activation of peroxymonosulfate with cobalt embedded in layered δ-MnO2 for degradation of dimethyl phthalate: Mechanisms, degradation pathway, and DFT calculation.

The sulfate radical-based advanced oxidation processes (SR-AOPs) offer huge potential for the removal of organic pollutants. In this study, Co(II)-intercalated δ-MnO2 (Co-δ-MnO2) catalyst was successfully prepared by a simple cation exchange reaction. The obtained Co-δ-MnO2 exhibited high catalytic performance for the removal of dimethyl phthalate (DMP) under the activation of peroxymonosulfate (PMS), with the degradation efficiency reaching 100% within 6 h. Experiments and theoretical calculations revealed that interlayer Co(II) provided unique active sites in Co-δ-MnO2. In addition, radical and non-radical pathways were confirmed to play a role in Co-δ-MnO2/PMS system. •OH, SO4• ̶, and 1O2 were identified to be the dominating reactive species in Co-δ-MnO2/PMS system. This study provided new insights into the design of catalysts and laid a foundation for developing modifiable layered heterogeneous catalysts.

Degradation kinetics and transformation pathway of methyl parathion by δ-MnO2/oxalic acid reaction system.

Methyl parathion (MP) is a typical organophosphorus pesticide that is widely used worldwide, and hydrolysis, oxidation and reduction are the main abiotic degradation processes. Manganese dioxide (MnO2) and organic acid can participate in various geochemical processes of pollutants, a reaction system was constructed to degrade MP using δ-MnO2 and oxalic acid. The δ-MnO2/oxalic acid reaction system could efficiently degrade MP, and the removal rate of MP (20 µM) reached 67.83% within 30 h under the optimized conditions (pH 5, [δ-MnO2] = 2 mM, [oxalic acid] = 100 mM). MP was hydrolyzed by substitution reactions of SN@P and SN@C, and reduced by conversion of the nitro groups (-NO2) in MP and its hydrolysates to amino groups (-NH2). The primary active substance produced in the reaction system was the complexes dominated by Mn(III)-oxalic acid. This study provides a scientific basis for the degradation of organophosphorus pesticides using MnO2 and an organic acid. The results have important theoretical significance and application value for pollution control and remediation of organophosphorus pesticides.

Optimization of acetamide based deep eutectic solvents with dual cations for high performance and low temperature-tolerant aqueous zinc ion batteries via tuning the ratio of co-solvents.

In this work, a novel acetamide-based deep eutectic solvent (DES) with Zn2+/ Li+ dual ions is designed and its physicochemical properties are tuned by adjusting the co-solvents (water and acetonitrile). Furthermore, the interplay between electrolyte components is investigated by spectroscopic analyses and molecular dynamics calculations. The addition of acetonitrile facilitates the formation of solid electrolyte interphase (SEI) with organic/inorganic components on the zinc anode. The presence of SEI coating enhances Coulombic efficiency and cycling stability by inhibiting the parasitic reactions and dendrite formation in the anode. The advantages of using dual cations in DES are demonstrated by assembling Zn ion batteries (ZIB) with the composite of δ-MnO2 and reduced graphene oxide as the cathode. The study of electrode kinetics in hybrid DES electrolytes suggests that Zn2+ and Li+ ions are responsible for battery-like and pseudocapacitive behavior of δ-MnO2 electrodes, respectively. With these merits, ZIB with the cutoff voltage of 2 V delivers a high cell capacity of 208 mAh g-1 at 0.1 Ag-1 and achieves 91% capacity retention after 1500 cycles at 2 Ag-1. More importantly, ZIB with hybrid DES is stably operated at the temperature of -20 °C, which is impossibly achieved by ZIB with conventional aqueous electrolytes.

Oxygen vacancies refilling and potassium ions intercalation of δ-manganese dioxide with high structural stability toward 2.3 V high voltage asymmetric supercapacitors.

Oxygen vacancies occupation and coordination environment modulation of the transition-metal based electrodes are effective strategies to improve the structural stability and electrochemical performance. In this work, the 2-methylimidazole (2-MI) doped manganese dioxide (MnO2) anchored on carbon cloth (CC) is fabricated via a simple method (MI-MnO2-x/CC), where the oxygen defects on/inside the K+ doped δ-MnO2 nanosheets are in-situ created by reductive ethanol/Mn2+ and occupied by 2-MI ligands. With the pre-embedded K+ ions and abundant ligand-refilled defects, the electronic coordination structure, structural stability and electron/ion diffusion efficiency can be effectively enhanced. Therefore, the MI-MnO2-x/CC reveals a remarkable specific capacitance of 721.2 mF cm-2 with excellent cycle durability (capacitance retention of 93.4% after 10,000 cycles) under 1.3 V operation potential window. In addition, an asymmetric supercapacitor assembled by MI-MnO2-x/CC and activated mechanical exfoliated graphene oxide yields a maximum energy density of 57.0 Wh kg-1 and a highest power density of 23.0 kW kg-1 under 2.3 V. This effective oxygen defect stabilization strategy by ligands refilling can be extended to various metal oxide-based electrodes for energy storage and conversion.

New insight of Mn(III) in δ-MnO2 for peroxymonosulfate activation reaction: Via direct electron transfer or via free radical reactions.

Due to the increasing of industrial plastic waste and its refractory characteristics, it is extremely urgent to develop new degradation technology and environmentally friendly catalyst for industrial plastic waste. Manganese oxides are one of the most promising candidates for the catalytic degradation of plastic wastes. However, an improved understanding of the structural properties affecting their catalytic activity is required for high-efficient wastewater treatment. We herein report the surface reactivity effects of δ-MnO2 structural defects with regards to Bisphenol A (BPA) degradation/probe in the presence of peroxymonosulfate (PMS). Four δ-MnOx samples with different Mn(III) contents (different Mn(III)-deficient sample) were prepared and their structural properties as well as surface reactivity were characterized by batch test, ESR and XAFS analysis. For the Mn(III)-deficient sample, BPA removal was principally affected by direct electron transfer, with the adsorbed BPA degraded following hydroxylation. In contrast, a small fraction of Mn(III) substitution in δ-MnO2 could significantly encouraged the activation of PMS to produce SO4-☐and ☐OH, and a BPA degradation via beta scission. Moreover, the Mn(III)-rich δ-MnO2 demonstrate a high BPA removal rate even with a low sample load, which performed well following a reuse of five times. Our results provide a new way for the improvement of δ-MnO2 activity for the use of industrial plastic wastes treatment.

Engineering p-Band Center of Oxygen Boosting H+ Intercalation in δ-MnO2 for Aqueous Zinc Ion Batteries.

In aqueous zinc ion batteries (ZIBs), the H+ intercalation possesses superior electrochemical kinetics with excellent rate capability, however, precisely modulating H+ intercalation has been still challenging. Herein, a critical modification of pre-intercalating metal ions in the MnO2 interlayer (M-MnO2 ) with controllable p-band center (ϵp ) of O is reported to modulate the H+ intercalation. The modulation of metal-O bond type and covalency degree on the average charge of O atom results in optimized ϵp and H+ adsorption energy for M-MnO2 , thus promoting the balance between H+ adsorption and desorption, which plays a determinant role on H+ intercalation. The optimized Cu-MnO2 delivers superior rate capability with the capacity of 153 mAh g-1 at a high rate of 3 A g-1 after 1000 cycles. This work demonstrates that ϵp could be a significant descriptor for H+ intercalation, and tuning ϵp effectively increases H+ intercalation contribution with excellent rate capability in ZIBs.

Solar irradiation accelerates the oxidation of Cr(III) by δ-manganese dioxide.

Cr(VI) has been observed to be released from Cr(III)-bearing natural sources or residues when they are found alongside manganese and manganese oxides. However, relevant mechanism studies normally ignore the effect of simulated solar irradiation on this oxidation reaction. Therefore, we investigated the photochemical reaction between Cr(OH)3 and δ-MnO2, the common species of chromium and manganese oxide found in the environment. At pH 11, the oxidation of Cr(OH)3 by δ-MnO2 was accelerated under simulated solar irradiation, which had an oxidation rate 2.7-fold greater than that in the dark condition. Further investigation revealed that δ-MnO2, an n-type semiconductor with a 2.7 eV band gap, can be excited by light with wavelengths < 459 nm and produce photogenic electrons and holes. These photo-induced carriers reacted with surrounding molecules to form free radicals and participate the redox reactions. Free-radical quenching experiments indicated that hydroxyl radicals (•OH) are the main oxidants of Cr(III) under simulated solar irradiation. This work provides new mechanistic insight into the oxidation of Cr(III) to Cr(VI), which may help clarifying the environmental fate of Cr and the potential solar-triggered release of Cr(VI).